Field-Effect and Frequency Dependent Transport in Semiconductor-Enriched Single-Wall Carbon Nanotube Network Device

The electrical and optical response of a field-effect device comprising a network of semiconductor-enriched single-wall carbon nanotubes, gated with sodium chloride solution is investigated. Field-effect is demonstrated in a device that uses facile fabrication techniques along with a small-ion as the gate electrolyte-and this is accomplished as a result of the semiconductor enhancement of the tubes. The optical transparency and electrical resistance of the device are modulated with gate voltage. A time-response study of the modulation of optical transparency and electrical resistance upon application of gate voltage suggests the percolative charge transport in the network. Also the ac response in the network is investigated as a function of frequency and temperature down to 5 K. An empirical relation between onset frequency and temperature is determined.

Effect of oxygen partial pressure on the growth of zinc micro and nanostructures

Zinc micro and nanostructures were synthesized in vacuum by condensing evaporated zinc on Si substrate at different gas pressures. The morphology of the grown Zn structures was found to be dependent on the oxygen partial pressure. Depending on oxygen partial pressure it varied from two-dimensional microdisks to one-dimensional nanowire. The morphology and structural properties of the grown micro and nanostructures were studied by scanning electron microscopy (SEM) and X-ray diffraction (XRD). Transmission electron microscopy (TEM) studies on the grown Zn nanowires have shown that they exhibit core/shell-like structures, where a thin ZnO layer forms the shell. A possible growth mechanism behind the formation of different micro and nanostructures has been proposed. In addition, we have synthesized ZnO nanocanal-like structures by annealing Zn nanowires in vacuum at 350 °C for 30 min.

Influence of Solvents on the MWCNT/Adhesive Grade Epoxy Nanocomposites Preparation

In this article, the effect of two solvents, namely dimethyl formamide (DMF) and N-methyl pyrrolidone (NMP), on the dispersion effectiveness and the resulting electrical and mechanical properties of multi-walled carbonanotubes (MNCNT) filled structural adhesive grade epoxy nanocomposites was studied. The solvents were used mainly to reduce the viscosity of the resin system to effectively disperse the nanofiller. The dispersion was carried out under vacuum using high energy sonic waves. SEM was undertaken to study the dispersion effectiveness. Electrical resistivity, tensile properties, and glass transition of the nanocomposites were studied. Between DMF and NMP, the former proved better in terms of dispersion effectiveness and the resulting electrical and mechanical properties of the nanocomposites. Addition of MWCNT into AV138M resulted in an increase in glass transition temperature irrespective of the solvent used and in both cases percolation threshold was found with respect to reduction in electrical resistivity of the nanocomposites. Less agglomeration and hence better interaction between CNT and epoxy was observed in the samples prepared using DMF compared with that using NMP.

The effect of lignin content and lignin modification on Norway spruce wood properties and decay resistance

Three different Norway spruce cutting clones growing in three environments with different soil and climatic conditions were studied. The purpose was to follow variation in the radial growth rate, wood properties and lignin content and to modify wood lignin with a natural monolignol, coniferyl alcohol, by making use of inherent wood peroxidases. In addition, the incorporation of chlorinated anilines into lignin was studied with synthetic model compounds and synthetic lignin preparations to show whether unnatural compounds originating from pesticides could be bound in the lignin polymer. The lignin content of heartwood, sapwood and earlywood was determined by applying Fourier transform infrared (FTIR) spectroscopy and a principal component regression (PCR) technique. Wood blocks were treated with coniferyl alcohol by using a vacuum impregnation method. The effect of impregnation was assessed by FTIR and by a fungal decay test. Trees from a fertile site showed the highest growth rate and sapwood lignin content and the lowest latewood proportion, weight density and modulus of rupture (MOR). Trees from a medium fertile site had the lowest growth rate and the highest latewood proportion, weight density, modulus of elasticity (MOE) and MOR. The most rapidly growing clone showed the lowest latewood proportion, weight density, MOE and MOR. The slowest growing clone had the lowest sapwood lignin content and the highest latewood proportion, weight density, MOE and MOR. Differences between the sites and clones were small, while fairly large variation was found between the individual trees and growing seasons. The cutting clones maintained clone-dependent wood properties in the different growing sites although variation between trees was high and climatic factors affected growth. The coniferyl alcohol impregnation increased the content of different lignin-type phenolic compounds in the wood as well as wood decay resistance against a white-rot fungus, Coriolus versicolor. During the synthetic lignin preparation 3,4-dichloroaniline became bound by a benzylamine bond to β-O-4 structures in the polymer and it could not be released by mild acid hydrolysis. The natural monolignol, coniferyl alcohol, and chlorinated anilines could be incorporated into the lignin polymer in vivo and in vitro, respectively.

Highly stable oscillator for quartz crystal thickness monitor

A highly stable oscillator used in a quartz crystal thickness monitor for monitoring the rate of evaporation and total thickness of film during thin film deposition is reported. The design aspects of the oscillator and its long term stability, which enhances the reproducibility and the performance of the thickness monitor, are discussed. The stability of the oscillator at defined conditions is tested and compared with the conventional transistorized oscillator and the IC oscillator using inverters. The oscillator is coupled to the crystal monitor and its performance is studied in an evaporation system by evaporating different materials

Synthesis of liquid crystalline benzothiazole base derivatives: A study of their optical and electrical properties

Two new donor-acceptor type liquid crystalline semiconductors based on benzothiazole have been synthesized. Their structural, photophysical and electronic properties were investigated using X-ray diffraction, atomic force microscopy, cyclic voltammetry, UV-Vis, photoluminescence, and Raman spectroscopy. The liquid crystalline behaviour of the molecules was thoroughly examined by differential scanning calorimetry (DSC) and optical polarizing microscope. The DSC and thermogravimetric analysis (TGA) show that these materials posses excellent thermal stability and have decomposition temperatures in excess of 300 degrees C. Beyond 160 degrees C both molecules show a smectic A liquid crystalline phase that exists till about 240 degrees C. Field-effect transistors were fabricated by vacuum evaporating the semiconductor layer using standard bottom gate/top contact geometry. The devices exhibit p-channel behaviour with hole mobilities of 10(-2) cm(2)/Vs. (C) 2009 Elsevier B.V. All rights reserved.

A germanium/single-walled carbon nanotube composite paper as a free-standing anode for lithium-ion batteries

Paper-like free-standing germanium (Ge) and single-walled carbon nanotube (SWCNT) composite anodes were synthesized by the vacuum filtration of Ge/SWCNT composites, which were prepared by a facile aqueous-based method. The samples were characterized by X-ray diffraction, field emission scanning electron microscopy, and transmission electron microscopy. Electrochemical measurements demonstrate that the Ge/SWCNT composite paper anode with the weight percentage of 32% Ge delivered a specific discharge capacity of 417 mA h g-1 after 40 cycles at a current density of 25 mA g-1, 117% higher than the pure SWCNT paper anode. The SWCNTs not only function as a flexible mechanical support for strain release, but also provide excellent electrically conducting channels, while the nanosized Ge particles contribute to improving the discharge capacity of the paper anode.

A numerical study of the effect of loading conditions on tubular hydroforming

In this work, the mechanics of tubular hydroforming under various types of loading conditions is investigated. The main objective is to contrast the effects of prescribing fluid pressure or volume flow rate, in conjunction with axial displacement, on the stress and strain histories experienced by the tube and the process of bulging. To this end, axisymmetric finite element simulations of free hydroforming (without external die contact) of aluminium alloy tubes are carried out. Hill’s normally anisotropic yield theory along with material properties determined in a previous experimental study [A. Kulkarni, P. Biswas, R. Narasimhan, A. Luo, T. Stoughton, R. Mishra, A.K. Sachdev, An experimental and numerical study of necking initiation in aluminium alloy tubes during hydroforming, Int. J. Mech. Sci. 46 (2004) 1727–1746] are employed in the computations. It is found that while prescribed fluid pressure leads to highly non-proportional strain paths, specified fluid volume flow rate may result in almost proportional ones for the predominant portion of loading. The peak pressure increases with axial compression for the former, while the reverse trend applies under the latter. The implication of these results on failure by localized necking of the tube wall is addressed in a subsequent investigation.

A theoretical model for the magnetic helicity of solar active regions

Active regions on the solar surface are known to possess magnetic helicity, which is predominantly negative in the northern hemisphere and positive in the southern hemisphere. Choudhuri et al. [Choudhuri, A.R. On the connection between mean field dynamo theory and flux tubes. Solar Phys. 215, 31–55, 2003] proposed that the magnetic helicity arises due to the wrapping up of the poloidal field of the convection zone around rising flux tubes which form active regions. Choudhuri [Choudhuri, A.R., Chatterjee, P., Nandy, D. Helicity of solar active regions from a dynamo model. ApJ 615, L57–L60, 2004] used this idea to calculate magnetic helicity from their solar dynamo model. Apart from getting broad agreements with observational data, they also predict that the hemispheric helicity rule may be violated at the beginning of a solar cycle. Chatterjee et al. [Chatterjee, P., Choudhuri, A.R., Petrovay, K. Development of twist in an emerging magnetic flux tube by poloidal field accretion. A&A 449, 781–789, 2006] study the penetration of the wrapped poloidal field into the rising flux tube due to turbulent diffusion using a simple 1-d model. They find that the extent of penetration of the wrapped field will depend on how weak the magnetic field inside the rising flux tube becomes before its emergence. They conclude that more detailed observational data will throw light on the physical conditions of flux tubes just before their emergence to the photosphere.

An elementary introduction to solar dynamo theory

The cyclically varying magnetic field of the Sun is believed to be produced by the hydromagnetic dynamo process. We first summarize the relevant observational data pertaining to sunspots and solar cycle. Then we review the basic principles of MHD needed to develop the dynamo theory. This is followed by a discussion how bipolar sunspots form due to magnetic buoyancy of flux tubes formed at the base of the solar convection zone. Following this, we come to the heart of dynamo theory. After summarizing the basic ideas of a turbulent dynamo and the basic principles of its mean field formulation, we present the famous dynamo wave solution, which was supposed to provide a model for the solar cycle. Finally we point out how a flux transport dynamo can circumvent some of the difficulties associated with the older dynamo models.

Variations in paediatric upper respiratory surgery rates within and between two Nordic countries

Lasten ylähengitystiekirurgia (kita-nielurisojen poisto ja tärykalvon putkitus) on länsimaissa erittäin yleistä. Leikkausten lukumäärät vaihtelevat niin kansallisesti kuin kansainvälisestikin, mutta selvää syytä näille eroille ei tiedetä. Hoitosuositusten merkitys käytäntöihin on kyseenalaistettu ja voi olla, ettei hoitosuosituksia noudateta. Leikkaukset saattavat aiheuttaa lapsipotilaille psykologisen vamman, ja lisäksi niihin sisältyy komplikaatioiden, jopa kuoleman, vaara. Jotta haittoja voidaan välttää, on tärkeää tunnistaa ne lapset, jotka hyötyvät leikkauksesta. Ongelma on paitsi lääketieteellinen, myös taloudellinen: ylähengitystiekirurgiasta aiheutuu merkittäviä kuluja. Leikkausmäärien arvioiminen on tärkeää, jotta leikkauskäytäntöjä voidaan järkeistää. Tässä väitöskirjatyössä tutkittiin ylähengitystieleikkausten määriä Suomessa ja Norjassa sekä näiden kahden maan välillä. Aiempaa tutkimusta aiheesta ei kummassakaan maassa ole tehty. Kitarisanpoiston, välikorvan putkituksen, tärykalvopiston, nielurisanpoiston ja kita- ja nielurisanpoiston leikkausmäärät saatiin kansallisista tietokannoista. Lukuja verrattiin ko. maan lasten lukumäärään, maantieteelliseen sijoittumiseen sekä lasten ikään ja sukupuoleen. Lisäksi leikkausmääriä arvioitiin suhteessa korva-, nenä- ja kurkkulääkäreiden sekä yleislääkäreiden määrään, maantieteelliseen sijoittumiseen ja lääkäreiden ikään ja sukupuoleen. Leikkausten määrissä havaittiin suurta vaihtelua niin Suomessa kuin Norjassa. Suomessa suurimmat erot leikkausmäärissä löydettiin läntisen ja itäisen miljoonapiirin välillä. Läntisessä piirissä tehtiin lähes kaksin kertaa enemmän leikkauksia kuin itäisessä piirissä. Norjassa suurimmat erot olivat pohjoisen ja itäisen piirin välillä. Pohjoisessa piirissä tehtiin kaksinkertainen määrä leikkauksia itäiseen piirrin verrattuna. Suomessa tehtiin tutkimuksen koko aikavälillä enemmän kitarisanpoistoja kuin Norjassa, mutta ko. leikkausten määrä oli maassamme selvästi laskussa. Vuonna 2002 Suomessa tehtiin 2,5 kertaa enemmän kitarisanpoistoja kuin Norjassa. (Kita)nielurisanpoistoja tehtiin kuitenkin Suomessa vähemmän kuin Norjassa. Näiden leikkausten määrät pysyivät tutkimuksen aikavälillä Suomessa samalla tasolla, kun Norjassa leikkausmäärät hieman nousivat. Suomalaisia lapsia leikattiin keskimäärin paljon nuorempina kuin norjalaisia lapsia. Tutkimuksessa ei löydetty selitystä ylähengitystieleikkausten määrän suurelle vaihtelulle Suomessa ja Norjassa tai maiden välillä. Kuitenkin Suomessa tehtyjen kitarisanpoistojen huomattavan vähenemisen myötä maiden ylähengitystieleikkausten määrät lähenivät toisiaan.

Electrical Properties of Thermal Evaporated Cd1−xMnxS Nanocrystalline Films

Thin films of Cd1−xMnxS (0<=x<=0.5) were deposited on glass substrates by thermal evaporation. All the films were deposited at 300 K and annealed at 373, 473, and 573 K for 1 h in a high vacuum in the range 10−4 Pa. The as-deposited and the annealed films were characterized for composition, structure, and microstructure by using energy-dispersive X-ray, X-ray diffraction, scanning electron microscopy, and atomic force microscopy (AFM). The electrical properties were studied by Hall effect measurement. Electrical conductivity was studied in the temperature range 190–450 K. AFM studies showed that all the films were in nanocrystalline form with grain size varying in the range between 36 and 82 nm. Grain size studies showed a definite increase with annealing temperature. All the films exhibited wurtzite structure of the host material. The lattice parameter varied linearly with composition, following Vegard's law in the entire composition range. Grain size, electrical conductivity, Hall mobility, carrier concentration, and activation energy varied, exhibiting either maxima or minima at x=0.3.

Experimental studies on a two stage pulse tube cryocooler reaching 2.5K

A two stage Pulse Tube Cryocooler (PTC) is designed and fabricated which reaches a no-load temperature of 2.5K in the second stage and similar to 60 K in the first stage respectively. The system provides a cooling power of similar to 250 mW at 5K in the second stage. Stainless steel meshes (size 200) and lead (Pb) granules are used as the first stage regenerator materials and combination of Pb with Er3Ni / HoCu2 are used as the second stage regenerator materials. The system operates at 1.6 Hz using a 6 kW water cooled helium compressor. Studies conducted by varying the dimensions of Pulse Tubes and regenerators show that the dimensions of the Pulse Tubes are more critical to the performance of the Cryocooler than those of the regenerators. Experimental studies show that the optimum volume ratios of Er3Ni to Pb and HoCu2 to Pb in the second stage regenerator should be 3:2 and 2:3 respectively for the best performance. Further, systems with HoCu2 performed better than those with Er3Ni. The theoretical analysis of the system has been carried out using a simple isothermal model. The experimentally measured cooling powers are in good agreement with the theoretical predictions.

Childhood otitis media - risk factors and surgical management

Background: Otitis media (OM) is one of the most common childhood diseases. Approximately every third child suffers from recurrent acute otitis media (RAOM), and 5% of all children have persistent middle ear effusion for months during their childhood. Despite numerous studies on the prevention and treatment of OM during the past decades, its management remains challenging and controversial. In this study, the effect of adenoidectomy on the risk for OM, the potential risk factors influencing the development of OM and the frequency of asthma among otitis-prone children were investigated. Subjects and methods: One prospective randomized trial and two retrospective studies were conducted. In the prospective trial, 217 children with RAOM or chronic otitis media with effusion (COME) were randomized to have tympanostomy with or without adenoidectomy. The age of the children at recruitment was between 1 and 4 years. RAOM was defined as having at least 3 episodes of AOM during the last 6 months or at least 5 episodes of AOM during the last 12 months. COME was defined as having persistent middle ear effusion for 2-3 months. The children were followed up for one year. In the first retrospective study, the frequency of childhood infections and allergy was evaluated by a questionnaire among 819 individuals. In the second retrospective study, data of asthma diagnosis were analysed from hospital discharge records of 1616 children who underwent adenoidectomy or had probing of the nasolacrimal duct. Results: In the prospective randomized study, adenoidectomy had no beneficial effect on the prevention of subsequent episodes of AOM. Parental smoking was found to be a significant risk factor for OM even after the insertion of tympanostomy tubes. The frequencies of exposure to tobacco smoke and day-care attendance at the time of randomization were similar among children with RAOM and COME. However, the frequencies of allergy to animal dust and pollen and parental asthma were lower among children with COME than those with RAOM. The questionnaire survey and the hospital discharge data revealed that children who had frequent episodes of OM had an increased risk for asthma. Conclusions: The first surgical intervention to treat an otitis-prone child younger than 4 years should not include adenoidectomy. Interventions to stop parental smoking could significantly reduce the risk for childhood RAOM. Whether an otitis-prone child develops COME or RAOM, seems to be influenced by genetic predisposition more strongly than by environmental risk factors. Children who suffer from repeated upper respiratory tract infections, like OM, may be at increased risk for developing asthma.

Steel-concrete-steel composite columns subjected to lateral impact

Concrete-filled double skin tube (CFDST) is a creative innovation of steel-concrete-steel composite construction, formed by two concentric steel tubes separated by a concrete filler. Over the recent years, this column form has been widely used as a new sustainable alternative to existing structural bridge piers and building columns. Since they could be vulnerable to impact from passing vessels or vehicles, it is necessary to understand their behaviour under lateral impact loads. With this in mind, physical tests on full scale columns were performed using an innovative horizontal impact testing system to obtain the failure modes, the time history of the impact force, reaction forces and global lateral deflection as well as permanent local buckling profile of the columns. The experimental testing was complemented and supplemented by developing and using an advanced finite element analysis model. The model was validated by comparing the numerical results against experimental data. The findings of this study will serve as a benchmark reference for future analysis and design of CFDST columns.