Manufacturing of self-passivating tungsten based alloys by different powder metallurgical routes

Self-passivating tungsten based alloys will provide a major safety advantage compared to pure tungsten when used as first wall armor of future fusion reactors, due to the formation of a protective oxide layer which prevents the formation of volatile and radioactive WO3 in case of a loss of coolant accident with simultaneous air ingress. Bulk WCr10Ti2 alloys were manufactured by two different powder metallurgical routes: (1) mechanical alloying (MA) followed by hot isostatic pressing (HIP) of metallic capsules, and (2) MA, compaction, pressureless sintering in H2 and subsequent HIPing without encapsulation. Both routes resulted in fully dense materials with homogeneous microstructure and grain sizes of 300 nm and 1 μm, respectively. The content of impurities remained unchanged after HIP, but it increased after sintering due to binder residue. It was not possible to produce large samples by route (2) due to difficulties in the uniaxial compaction stage. Flexural strength and fracture toughness measured on samples produced by route (1) revealed a ductile-to-brittle-transition temperature (DBTT) of about 950 °C. The strength increased from room temperature to 800 °C, decreasing significantly in the plastic region. An increase of fracture toughness is observed around the DBTT.

Thermodynamic, surface and structural properties of liquid Co-Si alloys

The knowledge of thermophysical properties of liquid Co-Si alloys is a key requirement for manufacturing of composite materials by infiltration method. Despite this need, the experimental and predicted property data of the Co-Si system are scarce and often inconsistent between the various sources. In the present work the mixing behaviour of Co-Si melts has been analysed through the study of the concentration dependence of various thermodynamic, surface (surface tension and surface composition) and structural properties (concentration fluctuations in the long-wavelength limit and chemical short-range order parameter) in the framework of the Compound Formation Model (CFM) and Quasi Chemical Approximation for regular solutions (QCA). In addition, the surface tension of the Co22·5Si77.5 (in at%) eutectic alloy, that is proposed to be used as the infiltrant, has been measured by the pendant drop method at temperatures ranging from 1593 to 1773 K. The results obtained were discussed with respect to both, temperature and concentration, and subsequently compared with the model predictions and literature data.

Refractory metals and their alloys : a literature search /

"January 1959."

Metallurgy of molybdenum, niobium, and molybdenum-niobium alloys : a literature search /

"TID-3572."

Extrusion of uranium, uranium alloys, and uranium compacts : a literature search /

This literature search consisting of 240 references to unclassified reports and published literature has been taken from Nuclear Science Abstracts, the official abstract journal of the United States Atomic Energy Commission. The period covered is January 1951 through May 31, 1961. Abstracts for the references can be found by use of the NSA abstract numbers provided.

The assayer's guide : or, practical directions to assayers, miners, and smelters, for the tests and assays, by heat and by wet processes, of the ores of all the principal metals, and of gold and silver coins and alloys, and of coal etc. /

Catalogue of practical and scientific books, published by Henry Carey Baird ... [24 p.] at end.

Engineering alloys; names, properties, uses,

"Directory of manufacturers and their alloys", p. [447]-520.

Amorphous boron-silicon-hydrogen alloys for thin films heterojunction solar-cell : quarterly technical progress report no. 1 for June 1 - August 31, 1970 /

"Work Performed Under Contract No. AC02-77CH00178."

Practical metallurgy; applied physical metallurgy and the industrial processing of ferrous and nonferrous metals and alloys,

Bibliographical footnotes.

Engineering alloys; names, properties, uses,

"Advertising": p. [447]-500.

A treatise on brasses, bronzes, and other alloys : and their constituent metals /

Includes bibliographical references.