891 resultados para Take-up rate
Resumo:
The pre-salt province is composed by large amounts of light oil and with good quality, a reality that puts Brazil in a strategic position facing the great demand for energy worldwide. In this province are the largest discoveries in the world in the last ten years; areas as Libra, Franco and Lula field, everyone containing volumes greater than 8 billion recoverable oil barrels. To develop and optimize the production of these fields, a study was done for choosing the improved oil recovery methods. The main motivations were the presence of carbon dioxide (CO2) as a contaminant and the strategic decision of do not discard it, combined with high GOR (gas-oil ratio) of the reservoir fluid. The method should take advantage of the unique abundant resources: seawater and produced gas. This way, the process of matching these resources in the water alterning gas injection (WAG) became a good option. In this master’s dissertation, it was developed a reservoir model with average characteristics of the Brazilian pre-salt, where was applied the improved oil recovery method of water alternating gas. The production of this reservoir was analyzed by parameters as: the first fluid injected in the injection process, position of the injection wells completion, injection water and gas rate and cycle time. The results showed a good performance of the method, with up to 26% of gains in the recovery factor regarding the primary recovery, since the application of water injection and gas, individually, was not able to overcome 10 % of gain. The most influential parameter found in the results was the cycle time, with higher recovery factor values obtained with the use of shorter times.
Resumo:
Automation of managed pressure drilling (MPD) enhances the safety and increases efficiency of drilling and that drives the development of controllers and observers for MPD. The objective is to maintain the bottom hole pressure (BHP) within the pressure window formed by the reservoir pressure and fracture pressure and also to reject kicks. Practical MPD automation solutions must address the nonlinearities and uncertainties caused by the variations in mud flow rate, choke opening, friction factor, mud density, etc. It is also desired that if pressure constraints are violated the controller must take appropriate actions to reject the ensuing kick. The objectives are addressed by developing two controllers: a gain switching robust controller and a nonlinear model predictive controller (NMPC). The robust gain switching controller is designed using H1 loop shaping technique, which was implemented using high gain bumpless transfer and 2D look up table. Six candidate controllers were designed in such a way they preserve robustness and performance for different choke openings and flow rates. It is demonstrated that uniform performance is maintained under different operating conditions and the controllers are able to reject kicks using pressure control and maintain BHP during drill pipe extension. The NMPC was designed to regulate the BHP and contain the outlet flow rate within certain tunable threshold. The important feature of that controller is that it can reject kicks without requiring any switching and thus there is no scope for shattering due to switching between pressure and flow control. That is achieved by exploiting the constraint handling capability of NMPC. Active set method was used for computing control inputs. It is demonstrated that NMPC is able to contain kicks and maintain BHP during drill pipe extension.
Resumo:
Recent studies have shown the importance of the beat-by-beat changes in heart rate influenced by the autonomic nervous system (ANS), or heart rate variability (HRV). The purpose of this study was to examine the lasting effects of hypoxic exercise on HRV, and its influences on substrate usage. Results from this study could lead an increased understanding on this topic. Eight active healthy males (age: 31±11 years; height: 180±7 cm; weight: 83±8 kg; VO₂max (maximal oxygen consumption): 4.4±0.6 L•min⁻¹) underwent normoxic and hypoxic (FᵢO₂= 0.15) conditions during high-intensity interval (HIIT) cycling (70%-high interval, 35%-rest interval). Cycling intensity was determined by a peak power output cycling test. Each experimental session consisted of a basal metabolic rate determination, up to 45-minutes of HIIT cycling, and three 30-minute post-exercise metabolic rate measurements (spanning 3 hours and 15 minutes after exercise). During exercise, RPE was higher (p<0.01) and LAC (lactate) increased (p=0.001) at each point of time in hypoxia, with no change in normoxia. After hypoxic exercise, the SNS/PNS ratio (overall ANS activity) was significantly higher (p<0.01) and significantly decreased through time in both conditions (p<0.01). In addition, a significant interaction between time and conditions (p<0.02) showed a decrease in LAC concentration through time post-hypoxic exercise. The findings showed that a single bout of hypoxic exercise alters ANS activity post-exercise along with shifting substrate partitioning from glycolytic to lipolytic energy production. The significant decrease in LAC concentration post-hypoxic exercise supports the notion that hypoxic HIIT induces a greater muscle glycogen depletion leading to increased fat oxidation to sustain glycogenesis and gluconeogenesis to maintain blood glucose level during recovery.
Resumo:
Software bug analysis is one of the most important activities in Software Quality. The rapid and correct implementation of the necessary repair influence both developers, who must leave the fully functioning software, and users, who need to perform their daily tasks. In this context, if there is an incorrect classification of bugs, there may be unwanted situations. One of the main factors to be assigned bugs in the act of its initial report is severity, which lives up to the urgency of correcting that problem. In this scenario, we identified in datasets with data extracted from five open source systems (Apache, Eclipse, Kernel, Mozilla and Open Office), that there is an irregular distribution of bugs with respect to existing severities, which is an early sign of misclassification. In the dataset analyzed, exists a rate of about 85% bugs being ranked with normal severity. Therefore, this classification rate can have a negative influence on software development context, where the misclassified bug can be allocated to a developer with little experience to solve it and thus the correction of the same may take longer, or even generate a incorrect implementation. Several studies in the literature have disregarded the normal bugs, working only with the portion of bugs considered severe or not severe initially. This work aimed to investigate this portion of the data, with the purpose of identifying whether the normal severity reflects the real impact and urgency, to investigate if there are bugs (initially classified as normal) that could be classified with other severity, and to assess if there are impacts for developers in this context. For this, an automatic classifier was developed, which was based on three algorithms (Näive Bayes, Max Ent and Winnow) to assess if normal severity is correct for the bugs categorized initially with this severity. The algorithms presented accuracy of about 80%, and showed that between 21% and 36% of the bugs should have been classified differently (depending on the algorithm), which represents somewhere between 70,000 and 130,000 bugs of the dataset.
Resumo:
Medical imaging technologies are experiencing a growth in terms of usage and image resolution, namely in diagnostics systems that require a large set of images, like CT or MRI. Furthermore, legal restrictions impose that these scans must be archived for several years. These facts led to the increase of storage costs in medical image databases and institutions. Thus, a demand for more efficient compression tools, used for archiving and communication, is arising. Currently, the DICOM standard, that makes recommendations for medical communications and imaging compression, recommends lossless encoders such as JPEG, RLE, JPEG-LS and JPEG2000. However, none of these encoders include inter-slice prediction in their algorithms. This dissertation presents the research work on medical image compression, using the MRP encoder. MRP is one of the most efficient lossless image compression algorithm. Several processing techniques are proposed to adapt the input medical images to the encoder characteristics. Two of these techniques, namely changing the alignment of slices for compression and a pixel-wise difference predictor, increased the compression efficiency of MRP, by up to 27.9%. Inter-slice prediction support was also added to MRP, using uni and bi-directional techniques. Also, the pixel-wise difference predictor was added to the algorithm. Overall, the compression efficiency of MRP was improved by 46.1%. Thus, these techniques allow for compression ratio savings of 57.1%, compared to DICOM encoders, and 33.2%, compared to HEVC RExt Random Access. This makes MRP the most efficient of the encoders under study.
Resumo:
This dissertation studies capacity investments in energy sources, with a focus on renewable technologies, such as solar and wind energy. We develop analytical models to provide insights for policymakers and use real data from the state of Texas to corroborate our findings.
We first take a strategic perspective and focus on electricity pricing policies. Specifically, we investigate the capacity investments of a utility firm in renewable and conventional energy sources under flat and peak pricing policies. We consider generation patterns and intermittency of solar and wind energy in relation to the electricity demand throughout a day. We find that flat pricing leads to a higher investment level for solar energy and it can still lead to more investments in wind energy if considerable amount of wind energy is generated throughout the day.
In the second essay, we complement the first one by focusing on the problem of matching supply with demand in every operating period (e.g., every five minutes) from the perspective of a utility firm. We study the interaction between renewable and conventional sources with different levels of operational flexibility, i.e., the possibility
of quickly ramping energy output up or down. We show that operational flexibility determines these interactions: renewable and inflexible sources (e.g., nuclear energy) are substitutes, whereas renewable and flexible sources (e.g., natural gas) are complements.
In the final essay, rather than the capacity investments of the utility firms, we focus on the capacity investments of households in rooftop solar panels. We investigate whether or not these investments may cause a utility death spiral effect, which is a vicious circle of increased solar adoption and higher electricity prices. We observe that the current rate-of-return regulation may lead to a death spiral for utility firms. We show that one way to reverse the spiral effect is to allow the utility firms to maximize their profits by determining electricity prices.
Resumo:
Grey seal, Halichoerus grypus, pups in the breeding colony at Froan, Norway, have a bimodal pattern of early aquatic behaviour. About 40% of the pups spend their time ashore to save energy, which can be allocated to growth or deposition of energy-rich adipose tissue. The other 60% of the pups enter the sea during suckling and the early postweaning period, and disperse to other locations within the breeding colony. Pups may swim distances up to 12 km. Neonatal aquatic dispersal behaviour may lead to increased energy expenditure for thermoregulation and swimming, and thus lead to a low rate of body mass gain during suckling and a high rate of body mass loss after weaning. Thus, we examined relationships between natal aquatic dispersal behaviour and change in body mass (DeltaBM) in suckling and weaned pups. Suckling pups that had dispersed >2000 m had a significantly lower DBM than suckling pups that dispersed <2000 m or that did not disperse. In weaned pups, there were no effects of aquatic dispersal behaviour on DBM. We suggest that the bimodal natal aquatic dispersal behaviour in grey seals at the study site reflects two different strategies for postweaning survival: to stay ashore and get fat, or to take a swim and acquire diving and feeding skills.
Resumo:
Ocean acidification (OA), induced by rapid anthropogenic CO2 rise and its dissolution in seawater, is known to have consequences for marine organisms. However, knowledge on the evolutionary responses of phytoplankton to OA has been poorly studied. Here we examined the coccolithophore Gephyrocapsa oceanica, while growing it for 2000 generations under ambient and elevated CO2 levels. While OA stimulated growth in the earlier selection period (from generations 700 to 1550), it reduced it in the later selection period up to 2000 generations. Similarly, stimulated production of particulate organic carbon and nitrogen reduced with increasing selection period and decreased under OA up to 2000 generations. The specific adaptation of growth to OA disappeared in generations 1700 to 2000 when compared with that at 1000 generations. Both phenotypic plasticity and fitness decreased within selection time, suggesting that the species' resilience to OA decreased after 2000 generations under high CO2 selection.
Resumo:
About 30% of the anthropogenically released CO2 is taken up by the oceans; such uptake causes surface ocean pH to decrease and is commonly referred to as ocean acidification (OA). Foraminifera are one of the most abundant groups of marine calcifiers, estimated to precipitate ca. 50 % of biogenic calcium carbonate in the open oceans. We have compiled the state of the art literature on OA effects on foraminifera, because the majority of OA research on this group was published within the last three years. Disparate responses of this important group of marine calcifiers to OA were reported, highlighting the importance of a process-based understanding of OA effects on foraminifera. We cultured the benthic foraminifer Ammonia sp. under a range of carbonate chemistry manipulation treatments to identify the parameter of the carbonate system causing the observed effects. This parameter identification is the first step towards a process-based understanding. We argue that CO3 is the parameter affecting foraminiferal size-normalized weights (SNWs) and growth rates. Based on the presented data, we can confirm the strong potential of Ammonia sp. foraminiferal SNW as a CO3 proxy.
Resumo:
As a consequence of anthropogenic CO2 emissions, oceans are becoming more acidic, a phenomenon known as ocean acidification. Many marine species predicted to be sensitive to this stressor are photosymbiotic, including corals and foraminifera. However, the direct impact of ocean acidification on the relationship between the photosynthetic and nonphotosynthetic organism remains unclear and is complicated by other physiological processes known to be sensitive to ocean acidification (e.g. calcification and feeding). We have studied the impact of extreme pH decrease/pCO2 increase on the complete life cycle of the photosymbiotic, non-calcifying and pure autotrophic acoel worm, Symsagittifera roscoffensis. Our results show that this species is resistant to high pCO2 with no negative or even positive effects on fitness (survival, growth, fertility) and/or photosymbiotic relationship till pCO2 up to 54 K µatm. Some sub-lethal bleaching is only observed at pCO2 up to 270 K µatm when seawater is saturated by CO2. This indicates that photosymbiosis can be resistant to high pCO2. If such a finding would be confirmed in other photosymbiotic species, we could then hypothesize that negative impact of high pCO2 observed on other photosymbiotic species such as corals and foraminifera could occur through indirect impacts at other levels (calcification, feeding).
Resumo:
The Sr/Ca of aragonitic coral skeletons is a commonly used palaeothermometer. However skeletal Sr/Ca is typically dominated by weekly-monthly oscillations which do not reflect temperature or seawater composition and the origins of which are currently unknown. To test the impact of transcellular Ca2+ transport processes on skeletal Sr/Ca, colonies of the branching coral, Pocillopora damicornis, were cultured in the presence of inhibitors of Ca-ATPase (ruthenium red) and Ca channels (verapamil hydrochloride). The photosynthesis, respiration and calcification rates of the colonies were monitored throughout the experiment. The skeleton deposited in the presence of the inhibitors was identified (by 42Ca spike) and analysed for Sr/Ca and Mg/Ca by secondary ion mass spectrometry. The Sr/Ca of the aragonite deposited in the presence of either of the inhibitors was not significantly different from that of the solvent (dimethyl sulfoxide) control, although the coral calcification rate was reduced by up to 66% and 73% in the ruthenium red and verapamil treatments, respectively. The typical precision (95% confidence limits) of mean Sr/Ca determinations within any treatment was <±1% and differences in skeletal Sr/Ca between treatments were correspondingly small. Either Ca-ATPase and Ca channels transport Sr2+ and Ca2+ in virtually the same ratio in which they are present in seawater or transcellular processes contribute little Ca2+ to the skeleton and most Ca is derived from seawater transported directly to the calcification site. Variations in the activities of Ca-ATPase and Ca-channels are not responsible for the weekly-monthly Sr/Ca oscillations observed in skeletal chronologies, assuming that the specificities of Ca transcellular transport processes are similar between coral genera.
Resumo:
In June 2015, legal frameworks of the Asian Infrastructural Investment Bank were signed by its 57 founding members. Proposed and initiated by China, this multilateral development bank is considered to be an Asian counterpart to break the monopoly of the World Bank and the International Monetary Fund. In October 2015, China’s Central Bank announced a benchmark interest rate cut to combat the economic slowdown. The easing policy coincides with the European Central Bank’s announcement of doubts over US Fed’s commitment to raise interest rates. Global stock markets responded positively to China’s move, with the exception of the indexes from Wall Street (Bland, 2015; Elliott, 2015). In the meantime, China’s ‘One Belt, One Road’ (or New Silk Road Economic Belt) became atopic of discourse in relation to its growing global economy, as China pledged $40 billion to trade and infrastructure projects (Bermingham, 2015). The foreign policy aims to reinforce the economic belt from western China through Central Asia towards Europe, as well as to construct maritime trading routes from coastal China through the South China Sea (Summers, 2015). In 2012, The Economist launched a new China section, to reveal the complexity of the‘meteoric rise’ of China. John Micklethwait, who was then the chief editor of the magazine, said that China’s emergence as a global power justified giving it a section of its own(Roush, 2012). In July 2015, Hu Shuli, the former chief editor of Caijing, announced the launch of a think tank and financial data service division called Caixin Insight Group, which encompasses the new Caixin China Purchasing Managers Index (PMI). Incooperation with with Markit Group, a principal global provider of PMI, the index soon became a widely cited economic indicator. One anecdote from November’s Caixin shows how much has changed: in a high-profile dialogue between Hu Shuli and Kevin Rudd, Hu insisted on asking questions in English; interestingly, the former Prime Minister of Australia insisted on replying in Chinese. These recent developments point to one thing: the economic ascent of China and its increasing influence on the power play between economics and politics in world markets. China has begun to take a more active role in rule making and enforcement under neoliberal frameworks. However, due to the country’s size and the scale of its economy in comparison to other countries, China’s version of globalisation has unique characteristics. The ‘Capitalist-socialist’ paradox is vital to China’s market-oriented transformation. In order to comprehend how such unique features are articulated and understood, there are several questions worth investigating in the realms of media and communication studies,such as how China’s neoliberal restructuring is portrayed and perceived by different types of interested parties, and how these portrayals are de-contextualised and re-contextualised in global or Anglo-American narratives. Therefore, based on a combination of the themes of globalisation, financial media and China’s economic integration, this thesis attempts to explore how financial media construct the narratives of China’s economic globalisation through the deployment of comparative and multi-disciplinary approaches. Two outstanding elite financial magazines, Britain’s The Economist, which has a global readership and influence, and Caijing, China’s leading financial magazine, are chosen as case studies to exemplify differing media discourses, representing, respectively, Anglo-American and Chinese socio-economic and political backgrounds, as well as their own journalistic cultures. This thesis tries to answer the questions of how and why China’s neoliberal restructuring is constructed from a globally-oriented perspective. The construction primarily involves people who are influential in business and policymaking. Hence, the analysis falls into the paradigm of elite-elite communication, which is an important but relatively less developed perspective in studying China and its globalisation. The comparing of characteristics of narrative construction are the result of the textual analysis of articles published over a ten-year period (mid-1998 to mid-2008). The corpus of samples come from the two media outlets’ coverage of three selected events:China becoming a member of the World Trade Organization, its outward direct investment, and the listing of stocks of Chinese companies in overseas exchanges, which are mutually exclusive in sample collection and collectively exhaustive in the inclusion of articles regarding China’s economic globalisation. The findings help to understand that, despite language, socio-economic and political differences, elite financial media with globally-oriented readerships share similar methods of and approaches to agenda setting, the evaluation of news prominence, the selection of frame, and the advocacy of deeply rooted neoliberal ideas. The comparison of their distinctive features reflects the different phases of building up the sense of identity in their readers as global elites, as well as the different economic interests that are aligned with the corresponding readerships. However, textual analysis is only relevant in terms of exploring how the narratives are constructed and the elements they include; textual analysis alone prevents us from seeing the obstacles and the constrains of the journalistic practices of construction. Therefore, this thesis provides a brief discussion of interviews with practitioners from the two media, in order to understand how similar or different narratives are manifested and perceived, how the concept of neoliberalism deviates from and is justified in the Chinese context, and how and for what purpose deviations arise from Western to Chinese contexts. The thesis also contributes to defining financial media in the domain of elite communication. The relevant and closely interlocking concepts of globalisation, elitism and neoliberalism are discussed, and are used as a theoretical bedrock in the analysis of texts and contexts. It is important to address the agenda-setting and ideological role of elite financial media, because of its narrative formula of infusing business facts with opinions,which is important in constructing the global elite identity as well as influencing neoliberal policy-making. On the other hand, ‘journalistic professionalism’ has been redefined, in that the elite identity is shared by the content producer, reader and the actors in the news stories emerging from the much-compressed news cycle. The professionalism of elite financial media requires a dual definition, that of being professional in the understanding of business facts and statistics, and that of being professional in the making sense of stories by deploying economic logic.
Resumo:
BACKGROUND: -There are few contemporary data on the mortality and morbidity associated with rheumatic heart disease (RHD) or information on their predictors. We report the two year follow-up of individuals with RHD from 14 low and middle income countries in Africa and Asia.
METHODS: -Between January 2010 and November 2012, we enrolled 3343 patients from 25 centers in 14 countries and followed them for two years to assess mortality, congestive heart failure (CHF), stroke or transient ischemic attack (TIA), recurrent acute rheumatic fever (ARF), and infective endocarditis (IE).
RESULTS: -Vital status at 24 months was known for 2960 (88.5%) patients. Two thirds were female. Although patients were young (median age 28 years, interquartile range 18 to 40), the two year case fatality rate was high (500 deaths, 16.9%). Mortality rate was 116.3/1000 patient-years in the first year and 65.4/1000 patient-years in the second year. Median age at death was 28.7 years. Independent predictors of death were severe valve disease (hazard ratio (HR) 2.36, 95% confidence interval (CI) 1.80-3.11), CHF (HR 2.16, 95% CI 1.70-2.72), New York Heart Association functional class III/IV (HR 1.67, 95% CI 1.32-2.10), atrial fibrillation (AF) (HR 1.40, 95% CI 1.10-1.78) and older age (HR 1.02, 95% CI 1.01-1.02 per year increase) at enrolment. Post-primary education (HR 0.67, 95% CI 0.54-0.85) and female sex (HR 0.65, 95%CI 0.52-0.80) were associated with lower risk of death. 204 (6.9%) had new CHF (incidence, 38.42/1000 patient-years), 46 (1.6%) had a stroke or TIA (8.45/1000 patient-years), 19 (0.6%) had ARF (3.49/1000 patient-years), and 20 (0.7%) had IE (3.65/1000 patient-years). Previous stroke and older age were independent predictors of stroke/TIA or systemic embolism. Patients from low and lower-middle income countries had significantly higher age- and sex-adjusted mortality compared to patients from upper-middle income countries. Valve surgery was significantly more common in upper-middle income than in lower-middle- or low-income countries.
CONCLUSIONS: -Patients with clinical RHD have high mortality and morbidity despite being young; those from low and lower-middle income countries had a poorer prognosis associated with advanced disease and low education. Programs focused on early detection and treatment of clinical RHD are required to improve outcomes.
Resumo:
Background: Medial UKA performed in England and Wales represents 7 to 11% of all knee arthroplasty procedures, and is most commonly performed using mobile-bearing designs. Fixed bearing eliminates the risk of bearing dislocation, however some studies have shown higher revision rates for all-polyethylene tibial components compared to those that utilize metal-backed implants. The aim of the study is to analyse survivorship and maximum 8-year clinical outcome of medial fixed bearing, Uniglide unicompartmental knee arthroplasty performed using an all-polyethylene tibial component with a minimal invasive approach. Methods: Between 2002 and 2009, 270 medial fixed UKAs were performed in our unit. Patients were reviewed pre-operatively, 5 and 8 years post-operatively. Clinical and radiographic reviews were carried out. Patients’ outcome scores (Oxford, WOMAC and American Knee Score) were documented in our database and analysed. Results: Survival and clinical outcome data of 236 knees with a mean 7.3 years follow-up are reported. Every patient with less than 4.93 years follow-up underwent a revision. The patients’ average age at the time of surgery was 69.5 years. The American Knee Society Pain and Function scores, the Oxford Knee Score and the WOMAC score all improved significantly. The 5 years survival rate was 94.1% with implant revision surgery as an end point. The estimated 10 years survival rate is 91.3%. 14 patients were revised before the 5 year follow-up. Conclusion: Fixed bearing Uniglide UKA with an all-polyethylene tibial component is a valuable tool in the management of a medial compartment osteoarthritis, affording good short term survivorship.
Resumo:
Abstract : The structural build-up of fresh cement-based materials has a great impact on their structural performance after casting. Accordingly, the mixture design should be tailored to adapt the kinetics of build-up given the application on hand. The rate of structural build-up of cement-based suspensions at rest is a complex phenomenon affected by both physical and chemical structuration processes. The structuration kinetics are strongly dependent on the mixture’s composition, testing parameters, as well as the shear history. Accurate measurements of build-up rely on the efficiency of the applied pre-shear regime to achieve an initial well-dispersed state as well as the applied stress during the liquid-solid transition. Studying the physical and chemical mechanisms of build-up of cement suspensions at rest can enhance the fundamental understanding of this phenomenon. This can, therefore, allow a better control of the rheological and time-dependent properties of cement-based materials. The research focused on the use of dynamic rheology in investigating the kinetics of structural build-up of fresh cement pastes. The research program was conducted in three different phases. The first phase was devoted to evaluating the dispersing efficiency of various disruptive shear techniques. The investigated shearing profiles included rotational, oscillatory, and combination of both. The initial and final states of suspension’s structure, before and after disruption, were determined by applying a small-amplitude oscillatory shear (SAOS). The difference between the viscoelastic values before and after disruption was used to express the degree of dispersion. An efficient technique to disperse concentrated cement suspensions was developed. The second phase aimed to establish a rheometric approach to dissociate and monitor the individual physical and chemical mechanisms of build-up of cement paste. In this regard, the non-destructive dynamic rheometry was used to investigate the evolutions of both storage modulus and phase angle of inert calcium carbonate and cement suspensions. Two independent build-up indices were proposed. The structural build-up of various cement suspensions made with different cement contents, silica fume replacement percentages, and high-range water reducer dosages was evaluated using the proposed indices. These indices were then compared to the well-known thixotropic index (Athix.). Furthermore, the proposed indices were correlated to the decay in lateral pressure determined for various cement pastes cast in a pressure column. The proposed pre-shearing protocol and build-up indices (phases 1 and 2) were then used to investigate the effect of mixture’s parameters on the kinetics of structural build-up in phase 3. The investigated mixture’s parameters included cement content and fineness, alkali sulfate content, and temperature of cement suspension. Zeta potential, calorimetric, spectrometric measurements were performed to explore the corresponding microstructural changes in cement suspensions, such as inter-particle cohesion, rate of Brownian flocculation, and nucleation rate. A model linking the build-up indices and the microstructural characteristics was developed to predict the build-up behaviour of cement-based suspensions The obtained results showed that oscillatory shear may have a greater effect on dispersing concentrated cement suspension than the rotational shear. Furthermore, the increase in induced shear strain was found to enhance the breakdown of suspension’s structure until a critical point, after which thickening effects dominate. An effective dispersing method is then proposed. This consists of applying a rotational shear around the transitional value between the linear and non-linear variations of the apparent viscosity with shear rate, followed by an oscillatory shear at the crossover shear strain and high angular frequency of 100 rad/s. Investigating the evolutions of viscoelastic properties of inert calcite-based and cement suspensions and allowed establishing two independent build-up indices. The first one (the percolation time) can represent the rest time needed to form the elastic network. On the other hand, the second one (rigidification rate) can describe the increase in stress-bearing capacity of formed network due to cement hydration. In addition, results showed that combining the percolation time and the rigidification rate can provide deeper insight into the structuration process of cement suspensions. Furthermore, these indices were found to be well-correlated to the decay in the lateral pressure of cement suspensions. The variations of proposed build-up indices with mixture’s parameters showed that the percolation time is most likely controlled by the frequency of Brownian collisions, distance between dispersed particles, and intensity of cohesion between cement particles. On the other hand, a higher rigidification rate can be secured by increasing the number of contact points per unit volume of paste, nucleation rate of cement hydrates, and intensity of inter-particle cohesion.