Type 20 Design B Port Side; SS Deep Water

Print No:66.

Type 20 Design C Port Side; SS Deep Water

Print No:66.

Type 20 Design D Starboard Side; SS Deep Water

Print No: 80.; Initials Lower Left: WH; Initials Lower Left: LY; Initials Lower Left: RN

Type 20 Design D Port Side; SS Deep Water

Print No: 66 (stamped on).; Initials Lower Left: WH; Initials Lower Left: LY; Initials Lower Left: RN

Are deep-sea cephalopods really common preys for oceanic seabirds?

Uma análise de dados publicados sobre dietas de aves marinhas oceânicas mostra a predominância de cefalópodes musculares e de distribuição mais superficial nas camadas oceânicas, mas também são importantes as espécies gelatinosas e amoniacais restritas a camadas abaixo dos 300 m da superfície. A princípio, não deveria se esperar que cefalópodes de profundidade fossem considerados presas comuns de aves marinhas oceânicas como reportados por muitos autores. É proposto neste estudo que uma fonte indireta, importante e de fácil obtenção, surgiu com o início das atividades dos barcos atuneiros que operam com espinhel. O hábito de ingerir restos de vísceras de peixes capturados em barcos espinheleiros pode explicar as prováveis conclusões equivocadas de que cefalópodes de profundidade são presas naturais de aves marinhas oceânicas.

Estimativa da erodibilidade do solo para fins conservacionistas na microbacia córrego do Tijuco, SP

The soil erodibility factor is represented by the integrated effect of processes that regulate the water infiltration, soil resistance and the transport of soil particles. Therefore, this study had as objective to estimate the soil erodibility in the Corrego do Tijuco watershed, São Paulo State, Brazil, for guiding farmers in decision making for application of techniques for soil conservation. The soil samples were collected in a regular spacing of 500 m, resulting in a total of 310 points in a 0-20.0 m depth in an area of approximately 8,000 ha. For the estimation of soil erodibility (K) was applied a mathematical model which takes into account the soil organic matter content, the sand and silt size fractions, the soil permeability, and the particle mean diameter for each point of soil sampling. Estimated values greater than 0.040 Mg ha h ha(-1) MJ(-1) mm(-1) were considered very high for this factor. In areas with greater degree of erodibility occurs the Argisols order predominance, that shows high susceptibility to the development of interrill erosion due to its remarkable performance in relation to textural gradient, thereby, the interrill erosion rates can be very intensive due to rapid saturation of upper horizon, increasing the erosion process. At the Latosols (Oxisols) areas were also observed high soil erodibility values that under inappropriate conditions of soil occupation, concentrating runoff of rain water, leading to appear deep gullies.

Effect of liming on the mineral nutrition and yield of growing guava trees in a typic hapludox soil

High soil acidity influences the availability of mineral nutrients and increases that of toxic aluminium (Al), which has a jeopardizing effect on plant growth. The objective of this research was to evaluate the effects of soil liming on the development of guava (Psidium guajava L.) plants, on soil chemical characteristics, and on fruit yield. The experiment was carried out at the Bebedouro Citrus Experimental Station, state of São Paulo, Brazil, in a Typic Hapludox soil, from August 1999 to March 2003. The treatments consisted of limestone dose: D0 = zero; D1 = half dose; D2 = total dose; D3 = 1.5 times the dose, and D4 = 2 times the dose to raise the V value to 70%. The doses corresponded to zero, 1.85, 3.71, 5.56, and 7.41tha(-1) applied to the upper soil layer (0-30cm deep) before planting. The results showed that liming caused an improvement in the evaluated soil chemical characteristics up to a depth of 60cm in soil samples both in the line and between lines. The highest fruit yields were obtained when the base saturation reached a value of 55% in the line and 62% between the lines. Foliar levels of calcium (Ca) and magnesium (Mg) were 8.8 and 2.5gkg-1, respectively. The highest limestone dose maintained the soil base saturation (at the layer of 0-20cm) in the line close to 55% during at least 40 months after the incorporation of limestone.

Resposta da caramboleira à calagem

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Desenvolvimento de uma ferramenta computacional para aplicação em métodos de elevação por bombeio centrífugo submerso

The Electrical Submersible Pump (ESP) has been one of the most appropriate solutions for lifting method in onshore and offshore applications. The typical features for this application are adverse temperature, viscosity fluids and gas environments. The difficulties in equipments maintenance and setup contributing to increasing costs of oil production in deep water, therefore, the optimization through automation can be a excellent approach for decrease costs and failures in subsurface equipment. This work describe a computer simulation related with the artificial lifting method ESP. This tool support the dynamic behavior of ESP approach, considering the source and electric energy transmission model for the motor, the electric motor model (including the thermal calculation), flow tubbing simulation, centrifugal pump behavior simulation with liquid nature effects and reservoir requirements. In addition, there are tri-dimensional animation for each ESP subsytem (transformer, motor, pump, seal, gas separator, command unit). This computer simulation propose a improvement for monitoring oil wells for maximization of well production. Currenty, the proprietaries simulators are based on specific equipments manufactures. Therefore, it is not possible simulation equipments of another manufactures. In the propose approach there are support for diverse kinds of manufactures equipments

Alterações em propriedades de solo adubado com doses de composto orgânico sob cultivo de bananeira

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

A dense GNSS meteorological network for observing deep convection in the Amazon

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Effect of pH of colloidal suspension on crystallization and activation energy of deep levels in SnO2 thin films obtained via sol-gel

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

A computational tool to assist the analysis of the transformer behavior related to lightning

This paper proposes the application of computational intelligence techniques to assist complex problems concerning lightning in transformers. In order to estimate the currents related to lightning in a transformer, a neural tool is presented. ATP has generated the training vectors. The input variables used in Artificial Neural Networks (ANN) were the wave front time, the wave tail time, the voltage variation rate and the output variable is the maximum current in the secondary of the transformer. These parameters can define the behavior and severity of lightning. Based on these concepts and from the results obtained, it can be verified that the overvoltages at the secondary of transformer are also affected by the discharge waveform in a similar way to the primary side. By using the tool developed, the high voltage process in the distribution transformers can be mapped and estimated with more precision aiding the transformer project process, minimizing empirics and evaluation errors, and contributing to minimize the failure rate of transformers. (C) 2011 Elsevier Ltd. All rights reserved.

A Comparison of Deep Drawing and Ironing of Metal Alloy Strip Produced conventionally and Non-conventionally via Semi Solid Material Processing

A semi solid thin strip continuous casting process was used to obtain 50%wt Pb/50%wtSn strip by single and twin roll processing at speed of 15 m/min. A 50%wt Pb/50%wtSn plate ingot was also cast for rolling conventionally into strips of 1.4 mm thickness and 45 mm width for comparison with those achieved non-conventionally. This hypoeutectic alloy has a solidification interval and fusion temperature of approximately 31 degrees C and 215 degrees C respectively. The casting alloy temperature was around 280 degrees C as measured by a type K immersion thermocouple prior to pouring into a tundish designed to maintain a constant melt flow on the cooling slope during semi solid material production. A nozzle with a weir ensures that the semi solid material is dragged smoothly by the lower roll, producing strip with minimum contamination of slag/oxide. The temperatures of the cooling slope and the lower roll were also monitored using K type thermocouples. The coiled semi solid strip, which has a thickness of 1.5 mm and 45 mm width, was rolled conventionally in order to obtain 1.2 mm thick strip. The coiled thixorolled strip had a thickness of 1.2 mm and achieved practically the same width as the conventional strips. Blanks of 40 mm diameter were cut from the strips in a mechanical press, ready for deep drawing and ironing for mechanical characterization. All the strips achieved from non-conventional processing had the same mechanical performance as those achieved conventionally. The limiting drawing ratio (LDR) achieved was approximately 2.0 for all strips. Microscopy examination was made in order to observe phase segregation during processing.