Consumo hídrico da rúcula em cultivo hidropônico NFT utilizando Rejeitos de dessalinizador em Ibimirim-PE

O consumo de águas salinas pelas plantas na maioria dos casos afetam o rendimento das culturas em suas diversas fases prejudicando desenvolvimento e produção. O trabalho avaliou o consumo hídrico da rúcula (Eruca sativa) em sistema hidropônico NFT com águas salinas. Foram analisados seis níveis crescentes de salinidade da água (CEa), quais sejam: 0,2; 1,2; 2,2; 3,2; 4,2 e 5,2 (dS m-1) utilizaram-se duas fontes de sais: águas salobras (AS) e NaCl. Foi determinado o volume evapotranspirado por planta (VETc) no sistema durante o cultivo. O consumo hídrico nos primeiros dias após transplantio foi de 250 mL dia-1 aproximadamente para ambas as testemunhas e decresceram com o aumento da salinidade, a eficiência de utilização da água foi reduzida revelando uma resposta linear decrescente em função da salinidade ocorrendo uma resposta negativa das plantas que apresentaram uma redução na quantidade de folhas de 3,34%.

Evaluating serial ZigBee devices for application in wireless networked control systems

Networked control systems (NCS) are distributed control system where the sensors, actuators and controllers are physically separated and connected through communication networks. NCS represent the evolution of networked control architectures providing greater modularity and control decentralization, ease maintenance and diagnosis and lower cost of implementation. A recent trend in this research topic is the development of NCS using wireless networks (WNCS) enabling interoperability between existing wired and wireless systems. This paper evaluates a serial RS-232 ZigBee device as a wireless sensor link in NCS. In order to support this investigation, relevant performance metrics for wireless control applications such as jitter, time delay and messages lost are highlighted and calculated to evaluate the device capabilities. In addition the control performance of an implemented motor control system using the device is analyzed. Experimental results led to the conclusion that serial RS-232 ZigBee devices can be used to implement WNCS and the use of this device delay information in the PID controller discretization can improve the control performance of the system. © 2012 IEEE.

Effect of different methods of cutting fluid application on turning of a difficult-to-machine steel (SAE EV-8)

In this study, different methods of cutting fluid application are used in turning of a difficult-to-machine steel (SAE EV-8). Initially, a semisynthetic cutting fluid was applied using a conventional method (i.e. overhead flood cooling), minimum quantity of cutting fluid, and pulverization. A lubricant of vegetable oil (minimum quantity of lubricant) was also applied using the minimum quantity method. Thereafter, a cutting fluid jet under high pressure (3.0 MPa) was singly applied in the following regions: chip-tool interface, top surface of the chip (between workpiece and chip) and tool-workpiece contact. Moreover, two other methods were used: an interflow between conventional application and chip-tool interface jet (combined method) and, finally, three jets simultaneously applied. In order to carry out these tests, it was necessary to set up a high-pressure system using a piston pump for generating a cutting fluid jet, a venturi for fluid application (minimum quantity of cutting fluid and minimum quantity of lubricant) and a nozzle for cutting fluid pulverization. The output variables analyzed included tool life, surface roughness, cutting tool temperature, cutting force, chip form, chip compression rate and machined specimen microstructure. Among the results, it can be observed that the tool life increases and the cutting force decreases with the application of cutting fluid jet, mainly when it is directed to the chip-tool interface. Excluding the methods involving jet fluid, the conventional method seems to be more efficient than other methods of low pressure, such as minimum quantity of volume and pulverization, when considering just the cutting tool wear. © 2013 IMechE.

Different methods of cutting fluid application on turning of a difficult-to-machine steel

Different methods of cutting fluid application are used on turning of a difficult-tomachine steel (SAE EV-8). A semi-synthetic cutting fluid was applied using a conventional method, minimum quantity of cutting fluid (MQCF), and pulverization. By the minimum quantity method was also applied a lubricant of vegetable oil (MQL). Thereafter, a cutting fluid jet under high pressure (3.0 MPa) was singly applied in the following regions: chip-tool interface; top surface of the chip; and tool-workpiece contact. Two other methods were used: an interflow between conventional application and chip-tool interface jet and, finally, three jets simultaneously applied. In order to carry out these tests, it was necessary to set up a high pressure system using a piston pump for generating a cutting fluid jet, a Venturi for fluid application (MQCF and MQL), and a nozzle for cutting fluid pulverization. The output variables analyzed included tool life, surface roughness, cutting tool temperature, cutting force, chip form, chip compression rate and machined specimen microstructure. It can be observed that the tool life increases and the cutting force decreases with the application of cutting fluid jet, mainly when it is directed to the chip-tool interface. Excluding the methods involving jet fluid, the conventional method seems to be more efficient than other methods of low pressure. © (2013) Trans Tech Publications, Switzerland.

Evaluation of Sperm Kinetics and Plasma Membrane Integrity of Frozen Equine Semen in Different Storage Volumes and Freezing Conditions

In the present study, different freezing systems (Styrofoam box and Mini Digitcool ZH 400) and storage volumes (0.5- and 0.25-mL straws) were compared with regard to sperm kinetics and plasma membrane integrity of frozen and thawed semen. For that, three ejaculates from four animals were frozen in Styrofoam box and Mini Digitcool ZH 400 machine. The 0.5-mL straws were thawed at 46°C for 20 seconds, and the 0.25-mL straws were thawed at 46°C for 12 seconds. Statistical analysis was performed using program R of descriptive analysis box plot, followed by analysis of variance using PROC MIXED of SAS 9.1 package. Variances of 5% were considered as different. There was no interaction between the straw sizes and volumes; however, statistical differences were observed between the semen storage volumes. The 0.5-mL straws had higher total motility (%), progressive motility (%), average path velocity (μm/s), straight-line velocity (μm/s), curvilinear velocity (μm/s), and rapid sperm percentage (%) than the 0.25-mL straws. However, plasma membrane integrity analysis did not differ between the two straws. Thus, it is possible to conclude that equine sperm cryopreserved in 0.5-mL straws has better sperm kinetics than when stored in 0.25-mL straws. Additionally, it is possible to conclude that automated systems that enable faster freezing rates result in a seminal quality that is similar to the one obtained by the conventional system using Styrofoam boxes. © 2013 Elsevier Inc.

Atividade respiratória de leucócitos como indicador de imunidade inata de pacu (Piaractus mesopotamicus)

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Occurrence of Cu and Cr in the sedimentary humic substances and pore water from a typical sugar cane cultivation area in São Paulo, Brazil

Purpose: The purpose of this paper is to study the interactions of sedimentary humic substances (SHS) from a sugarcane cultivation area with Cu(II) and Cr(III) and to evaluate the occurrence of these metals in the pore water and SHS. Materials and methods: For this study, the northwestern region of the State of São Paulo, Brazil, which is considered the region with the highest production of sugar cane in the state, was selected. Samples of sediment were collected from four sampling sites in the Preto, Turvo, and Grande rivers. The SHS and pore water were extracted from the sediment using the method suggested by the International Humic Substances Society and centrifugation, respectively. The complexing capacity (CC) of the SHS for Cu(II) and Cr(III) was determined by individually titrating these metals with an ultrafiltration system using tangential flow. The total concentrations of Cr and Cu were determined for the pore water, sediments, and humic substances with graphite furnace atomic absorption spectrometry and Zeeman background correction after an acid digestion, according to the methods described in US EPA Method 3050B. Results and discussion: The SHS from a site in the Turvo River, which is typically cultivated with sugarcane, possessed the highest concentration of Cu bound to SHS (25.0%), the largest CC (0.63 mmol Cu g-1 HS) and the highest concentration of this metal in the pore water (1.38 mg Cu Kg-1 sed.). For Cr, the SHS collected from a location on the Preto River dam had the largest CC (0.90 mmol Cr g-1 HS) and the lowest Cr content in the pore water (0.29 mg Cr Kg-1 sed.), indicating that there was an inverse relationship between the CC and the concentration of metal available in the pore water. Conclusions: Sedimentary humic substances might be one of the regulatory factors controlling the availability of Cu and Cr in the sediments found in a typical region that has been planted with sugarcane. Distinct behaviors were observed between the two elements investigated; higher CC and a larger fraction of Cu(II) were found in the pore water of samples originating from sugarcane crops. The opposite behavior was observed for the Cr(III) species. © 2013 Springer-Verlag Berlin Heidelberg.

Proteinograma do soro lácteo de ovelhas da raça santa inês em diferentes fases de lactação

This study aimed to evaluate the influence of lactation phases on the proteinogram of whey protein in Santa Inês ewes. Ewes were accompanied in a semi-intensive system using the same sanitary and nutritional management evaluated at 15, 30, 60 and 90 days postpartum (end of weaning and lactation). Clinical examination of the mammary gland was carried out through and bacteriological culture. The screening of the material resulted in 44 milk samples of healthy glands concurrent negative by CMT and bacteriological culture exam. For obtaining the whey protein renin solution was used. The whey was fractionated into aliquots and kept in the -80C freezer to later separation of protein fractions. For determination of total protein of whey protein was employed the biuret, observing the linearity of the test. Separation of protein fractions was performed, using polyacrylamide gel containing sodium dodecyl sulfate (SDS-PAGE). Eigth protein were observed including lactoferrin, serum albumin, IgA, IgG (heavy chain IgG (IgG CP), light chain IgG (IgG CL), ß-lactoglobulin, a-lactalbumin and proteins identified as PM 15000 and PM 29000. No significant difference was observed at different stages of lactation in the following protein: IgA (P>0.3895), lactoferrin (P>0.1611), PM 29000 (P>0.4879), α-lactalbumin (P>0.0799) and PM15000 (P>0.4494). In total protein (P<0.0022), albumin protein (P<0.0377) and IgG (P<0.0354) it was observed a significant variation in the first moments of observations, in the ß-lactoglobulin protein (P<0.0005) there was significant variation with reduction of 15 to 30 days postpartum with progressive elevation until the last stage of lactation (90 days postpartum). The SDS-PAGE technique allowed the quantification of eigth whey proteins in health ewes. The protein fractions identified reflect the profile of whey to ovine species, with influence of stages of lactation in albumin, IgG and ß-lactoglobulin.

Manejo do nitrogênio em cobertura na cultura do milho (Zea mays L.) em solo arenoso baseado no índice relativo de clorofila

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Decomposição de Dantzig-Wolfe aplicada ao problema de planejamento de reativos em sistemas de potência multi-áreas

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Metodologia de localização de defeitos em redes subterrâneas integrando PSCAD/EMTDC e sistemas inteligentes

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Alocação de pólos com realimentação da derivada dos estados usando LMIs

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Análise do aproveitamento energético do biogás produzido numa estação de tratamento de esgoto

Pós-graduação em Engenharia Mecânica - FEIS

Percepção de fala e ortografia de fricativas na escrita de crianças do ensino fundamental

Pós-graduação em Fonoaudiologia - FFC

Desenvolvimento de um sistema informatizado para coleta, armazenamento e processamento dos dados referentes à cesta básica do Município de Botucatu -SP

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)