Non-contact ACL injuries : association with clegg soil impact test values for sports fields, soil moisture and prevailing weather

Introduction: There is a recognised relationship between dry weather conditions and increased risk of anterior cruciate ligament (ACL) injury. Previous studies have identified 28 day evaporation as an important weather-based predictor of non-contact ACL injuries in professional Australian Football League matches. The mechanism of non-contact injury to the ACL is believed to increased traction and impact forces between footwear and playing surface. Ground hardness and the amount and quality of grass are factors that would most likely influence this and are inturn, related to the soil moisture content and prevailing weather conditions. This paper explores the relationship between soil moisture content, preceding weather conditions and the Clegg Soil Impact Test (CSIT) which is an internationally recognised standard measure of ground hardness for sports fields. Methodology: The 2.25 kg Clegg Soil Impact Test and a pair of 12 cm soil moisture probes were used to measure ground hardness and percentage moisture content. Five football fields were surveyed at 13 prescribed sites just before seven football matches from October 2008 to January 2009 (an FC Women’s WLeague team). Weather conditions recorded at the nearest weather station were obtained from the Bureau of Meteorology website and total rainfall less evaporation was calculated for 7 and 28 days prior to each match. All non-contact injuries occurring during match play and their location on the field were recorded. Results/conclusions: Ground hardness varied between CSIT 5 and 17 (x10G) (8 is considered a good value for sports fields). Variations within fields were typically greatest in the centre and goal areas. Soil moisture ranged from 3 to 40% with some fields requiring twice the moisture content of others to maintain similar CSIT values. There was a non-linear, negative relationship for ground hardness versus moisture content and a linear relationship with weather (R2, of 0.30 and 0.34, respectively). Three non-contact ACL injuries occurred during the season. Two of these were associated with hard and variable ground conditions.

Water absorption, permeability, and resistance to chloride-ion penetration of lightweight aggregate concrete

This paper presents an experimental study to evaluate effect of cumulative lightweight aggregate (LWA) content (including lightweight sand) in concrete [water/cement ratio (w/c) = 0.38] on its water absorption, water permeability, and resistance to chloride-ion penetration. Rapid chloride penetrability test (ASTM C 1202), rapid migration test (NT Build 492), and salt ponding test (AASHTO T 259) were conducted to evaluate the concrete resistance to chloride-ion penetration. The results were compared with those of a cement paste and a control normal weight aggregate concrete (NWAC) with the same w/c and a NWAC (w/c = 0.54) with 28-day compressive strength similar to some of the lightweight aggregate concrete (LWAC). Results indicate that although the total charge passed, migration coefficient, and diffusion coefficient of the LWAC were not significantly different from those of NWAC with the same w/c of 0.38, resistance of the LWAC to chloride penetration decreased with increase in the cumulative LWA content in the concretes. The water penetration depth under pressure and water sorptivity showed, in general, similar trends. The LWAC with only coarse LWA had similar water sorptivity, water permeability coefficient, and resistance to chloride-ion penetration compared to NWAC with similar w/c. The LWAC had lower water sorptivity, water permeability and higher resistance to chloride-ion penetration than the NWAC with similar 28-day strength but higher w/c. Both the NWAC and LWAC had lower sorptivity and higher resistance to chloride-ion penetration than the cement paste with similar w/c.

Fire performance of LSF walls made of hollow flange section studs

Load bearing Light Gauge Steel Frame (LSF) walls made of cold-formed steel studs and tracks are commonly used in residential and commercial buildings. Fire safety of these walls is essential to minimize the damage caused by fire related accidents. Past investigations on the fire performance of load bearing LSF wall systems have been limited to LSF walls made of conventional lipped channel section studs. Although structurally efficient hollow flange steel sections are available in the building industry, they are not used as LSF wall studs due to the lack of fire performance data for such walls. The hollow flange sections have torsionally rigid hollow flanges that eliminate the occurrence of local and distortional buckling to an extent, thereby increasing their structural efficiency. The weaknesses of hollow flange sections such as lower lateral distortional buckling capacity are also eliminated when they are used as studs of LSF walls as the plasterboard restraints will prevent any lateral movement. Therefore hollow flange sections can be considered as structurally more efficient studs for use in LSF wall systems. This paper reports the full scale fire tests of LSF walls made of hollow flange section studs under standard fire conditions. The frames were made of 1.6 mm thick and 150 mm deep hollow flange section studs with two closed rectangular flanges of 45 mm width x 15 mm depth. Dual plasterboards were attached on both sides of the test wall panels. The load ratio was varied and the failure times, the lateral deflections and the axial displacements of the test walls were obtained. The failure behaviour of LSF walls made of hollow flange section studs was found to be different to that of LSF walls made of conventional lipped channel section studs. The results of these fire tests show that hollow flange section studs have a higher potential in being used in load bearing LSF Walls.

Development of improved fire design rules for cold-formed steel wall systems

Traditionally the fire resistance rating of LSF wall systems is based on approximate prescriptive methods developed using limited fire tests. Therefore a detailed research study into the performance of load bearing LSF wall systems under standard fire conditions was undertaken to develop improved fire design rules. It used the extensive fire performance results of eight different LSF wall systems from a series of full scale fire tests and numerical studies for this purpose. The use of previous fire design rules developed for LSF walls subjected to non-uniform elevated temperature distributions based on AISI design manual and Eurocode3 Parts 1.2 and 1.3 was investigated first. New simplified fire design rules based on AS/NZS 4600, North American Specification and Eurocode 3 Part 1.3 were then proposed in this study with suitable allowances for the interaction effects of compression and bending actions. The importance of considering thermal bowing, magnified thermal bowing and neutral axis shift in the fire design was also investigated. A spread sheet based design tool was developed based on the new design rules to predict the failure load ratio versus time and temperature curves for varying LSF wall configurations. The accuracy of the proposed design rules was verified using the test and FEA results for different wall configurations, steel grades, thicknesses and load ratios. This paper presents the details and results of this study including the improved fire design rules for predicting the load capacity of LSF wall studs and the failure times of LSF walls under standard fire conditions.

Development of a simplified design method to predict the fire rating of LSF walls

Recent fire research into the behaviour of light gauge steel frame (LSF) wall systems has devel-oped fire design rules based on Australian and European cold-formed steel design standards, AS/NZS 4600 and Eurocode 3 Part 1.3. However, these design rules are complex since the LSF wall studs are subjected to non-uniform elevated temperature distributions when the walls are exposed to fire from one side. Therefore this paper proposes an alternative design method for routine predictions of fire resistance rating of LSF walls. In this method, suitable equations are recommended first to predict the idealised stud time-temperature pro-files of eight different LSF wall configurations subject to standard fire conditions based on full scale fire test results. A new set of equations was then proposed to find the critical hot flange (failure) temperature for a giv-en load ratio for the same LSF wall configurations with varying steel grades and thickness. These equations were developed based on detailed finite element analyses that predicted the axial compression capacities and failure times of LSF wall studs subject to non-uniform temperature distributions with varying steel grades and thicknesses. This paper proposes a simple design method in which the two sets of equations developed for time-temperature profiles and critical hot flange temperatures are used to find the failure times of LSF walls. The proposed method was verified by comparing its predictions with the results from full scale fire tests and finite element analyses. This paper presents the details of this study including the finite element models of LSF wall studs, the results from relevant fire tests and finite element analyses, and the proposed equations.

A performance test of query operation on encrypted database

Database security techniques are available widely. Among those techniques, the encryption method is a well-certified and established technology for protecting sensitive data. However, once encrypted, the data can no longer be easily queried. The performance of the database depends on how to encrypt the sensitive data, and an approach for searching and retrieval efficiencies that are implemented. In this paper we analyze the database queries and the data properties and propose a suitable mechanism to query the encrypted database. We proposed and analyzed the new database encryption algorithm using the Bloom Filter with the bucket index method. Finally, we demonstrated the superiority of the proposed algorithm through several experiments that should be useful for database encryption related research and application activities.

Challenging the female underperformance hypothesis

Purpose – The question of whether female-owned firms underperform male-owned firms has triggered much research and discussion. Klapper and Parker's review concluded that the majority of prior research suggests that female-owned firms underperform relative to male-owned firms. However, using performance measures that control for size and risk (and after controlling for demographic differences such as industry, experience and hours worked) Robb and Watson found no gender performance difference in their sample of newly established US firms. The aim of this study, therefore, is to replicate Robb and Watson's study to determine whether their findings can be generalized to another geographical location, Australia. Design/methodology/approach – The authors test the female underperformance hypothesis using data from the CAUSEE project, a panel study which follows young firms over four years. They use three outcome variables: survival rates, return on assets and the Sharpe ratio. Findings – Consistent with Robb and Watson the results indicate that female-owned firms do not underperform male-owned firms. Originality/value – While replication studies are rare in entrepreneurship, they are an important tool for accumulating generalizable knowledge. The results suggest that while female-owned firms differ from male-owned firms in terms of many control variables (such as industry, owners' previous experience and hours worked) they are no less successful. This outcome should help dispel the female underperformance myth; which if left unchallenged could result in inappropriate policy decisions and, more importantly, could discourage women from establishing new ventures.

Genetic improvement of giant freshwater prawn in Vietnam

The giant freshwater prawn (Macrobrachium rosenbergii) or GFP is one of the most important freshwater crustacean species in the inland aquaculture sector of many tropical and subtropical countries. Since the 1990’s, there has been rapid global expansion of freshwater prawn farming, especially in Asian countries, with an average annual rate of increase of 48% between 1999 and 2001 (New, 2005). In Vietnam, GFP is cultured in a variety of culture systems, typically in integrated or rotational rice-prawn culture (Phuong et al., 2006) and has become one of the most common farmed aquatic species in the country, due to its ability to grow rapidly and to attract high market price and high demand. Despite potential for expanded production, sustainability of freshwater prawn farming in the region is currently threatened by low production efficiency and vulnerability of farmed stocks to disease. Commercial large scale and small scale GFP farms in Vietnam have experienced relatively low stock productivity, large size and weight variation, a low proportion of edible meat (large head to body ratio), scarcity of good quality seed stock. The current situation highlights the need for a systematic stock improvement program for GFP in Vietnam aimed at improving economically important traits in this species. This study reports on the breeding program for fast growth employing combined (between and within) family selection in giant freshwater prawn in Vietnam. The base population was synthesized using a complete diallel cross including 9 crosses from two local stocks (DN and MK strains) and a third exotic stock (Malaysian strain - MY). In the next three selection generations, matings were conducted between genetically unrelated brood stock to produce full-sib and (paternal) half-sib families. All families were produced and reared separately until juveniles in each family were tagged as a batch using visible implant elastomer (VIE) at a body size of approximately 2 g. After tags were verified, 60 to 120 juveniles chosen randomly from each family were released into two common earthen ponds of 3,500 m2 pond for a grow-out period of 16 to 18 weeks. Selection applied at harvest on body weight was a combined (between and within) family selection approach. 81, 89, 96 and 114 families were produced for the Selection line in the F0, F1, F2 and F3 generations, respectively. In addition to the Selection line, 17 to 42 families were produced for the Control group in each generation. Results reported here are based on a data set consisting of 18,387 body and 1,730 carcass records, as well as full pedigree information collected over four generations. Variance and covariance components were estimated by restricted maximum likelihood fitting a multi-trait animal model. Experiments assessed performance of VIE tags in juvenile GFP of different size classes and individuals tagged with different numbers of tags showed that juvenile GFP at 2 g were of suitable size for VIE tags with no negative effects evident on growth or survival. Tag retention rates were above 97.8% and tag readability rates were 100% with a correct assignment rate of 95% through to mature animal size of up to 170 g. Across generations, estimates of heritability for body traits (body weight, body length, cephalothorax length, abdominal length, cephalothorax width and abdominal width) and carcass weight traits (abdominal weight, skeleton-off weight and telson-off weight) were moderate and ranged from 0.14 to 0.19 and 0.17 to 0.21, respectively. Body trait heritabilities estimated for females were significantly higher than for males whereas carcass weight trait heritabilities estimated for females and males were not significantly different (P > 0.05). Maternal and common environmental effects for body traits accounted for 4 to 5% of the total variance and were greater in females (7 to 10%) than in males (4 to 5%). Genetic correlations among body traits were generally high in both sexes. Genetic correlations between body and carcass weight traits were also high in the mixed sexes. Average selection response (% per generation) for body weight (transformed to square root) estimated as the difference between the Selection and the Control group was 7.4% calculated from least squares means (LSMs), 7.0% from estimated breeding values (EBVs) and 4.4% calculated from EBVs between two consecutive generations. Favourable correlated selection responses (estimated from LSMs) were detected for other body traits (12.1%, 14.5%, 10.4%, 15.5% and 13.3% for body length, cephalothorax length, abdominal length, cephalothorax width and abdominal width, respectively) over three selection generations. Data in the second selection generation showed positive correlated responses for carcass weight traits (8.8%, 8.6% and 8.8% for abdominal weight, skeleton-off weight and telson-off weight, respectively). Data in the third selection generation showed that heritability for body traits were moderate and ranged from 0.06 to 0.11 and 0.11 to 0.22 at weeks 10 and 18, respectively. Body trait heritabilities estimated at week 10 were not significantly lower than at week 18. Genetic correlations between body traits within age and genetic correlations for body traits between ages were generally high. Overall our results suggest that growth rate responds well to the application of family selection and carcass weight traits can also be improved in parallel, using this approach. Moreover, selection for high growth rate in GFP can be undertaken successfully before full market size has been reached. The outcome of this study was production of an improved culture strain of GFP for the Vietnamese culture industry that will be trialed in real farm production environments to confirm the genetic gains identified in the experimental stock improvement program.

Improving ultrasound excitation systems using a flexible power supply with adjustable voltage and frequency to drive piezoelectric transducers

The ability of a piezoelectric transducer in energy conversion is rapidly expanding in several applications. Some of the industrial applications for which a high power ultrasound transducer can be used are surface cleaning, water treatment, plastic welding and food sterilization. Also, a high power ultrasound transducer plays a great role in biomedical applications such as diagnostic and therapeutic applications. An ultrasound transducer is usually applied to convert electrical energy to mechanical energy and vice versa. In some high power ultrasound system, ultrasound transducers are applied as a transmitter, as a receiver or both. As a transmitter, it converts electrical energy to mechanical energy while a receiver converts mechanical energy to electrical energy as a sensor for control system. Once a piezoelectric transducer is excited by electrical signal, piezoelectric material starts to vibrate and generates ultrasound waves. A portion of the ultrasound waves which passes through the medium will be sensed by the receiver and converted to electrical energy. To drive an ultrasound transducer, an excitation signal should be properly designed otherwise undesired signal (low quality) can deteriorate the performance of the transducer (energy conversion) and increase power consumption in the system. For instance, some portion of generated power may be delivered in unwanted frequency which is not acceptable for some applications especially for biomedical applications. To achieve better performance of the transducer, along with the quality of the excitation signal, the characteristics of the high power ultrasound transducer should be taken into consideration as well. In this regard, several simulation and experimental tests are carried out in this research to model high power ultrasound transducers and systems. During these experiments, high power ultrasound transducers are excited by several excitation signals with different amplitudes and frequencies, using a network analyser, a signal generator, a high power amplifier and a multilevel converter. Also, to analyse the behaviour of the ultrasound system, the voltage ratio of the system is measured in different tests. The voltage across transmitter is measured as an input voltage then divided by the output voltage which is measured across receiver. The results of the transducer characteristics and the ultrasound system behaviour are discussed in chapter 4 and 5 of this thesis. Each piezoelectric transducer has several resonance frequencies in which its impedance has lower magnitude as compared to non-resonance frequencies. Among these resonance frequencies, just at one of those frequencies, the magnitude of the impedance is minimum. This resonance frequency is known as the main resonance frequency of the transducer. To attain higher efficiency and deliver more power to the ultrasound system, the transducer is usually excited at the main resonance frequency. Therefore, it is important to find out this frequency and other resonance frequencies. Hereof, a frequency detection method is proposed in this research which is discussed in chapter 2. An extended electrical model of the ultrasound transducer with multiple resonance frequencies consists of several RLC legs in parallel with a capacitor. Each RLC leg represents one of the resonance frequencies of the ultrasound transducer. At resonance frequency the inductor reactance and capacitor reactance cancel out each other and the resistor of this leg represents power conversion of the system at that frequency. This concept is shown in simulation and test results presented in chapter 4. To excite a high power ultrasound transducer, a high power signal is required. Multilevel converters are usually applied to generate a high power signal but the drawback of this signal is low quality in comparison with a sinusoidal signal. In some applications like ultrasound, it is extensively important to generate a high quality signal. Several control and modulation techniques are introduced in different papers to control the output voltage of the multilevel converters. One of those techniques is harmonic elimination technique. In this technique, switching angles are chosen in such way to reduce harmonic contents in the output side. It is undeniable that increasing the number of the switching angles results in more harmonic reduction. But to have more switching angles, more output voltage levels are required which increase the number of components and cost of the converter. To improve the quality of the output voltage signal with no more components, a new harmonic elimination technique is proposed in this research. Based on this new technique, more variables (DC voltage levels and switching angles) are chosen to eliminate more low order harmonics compared to conventional harmonic elimination techniques. In conventional harmonic elimination method, DC voltage levels are same and only switching angles are calculated to eliminate harmonics. Therefore, the number of eliminated harmonic is limited by the number of switching cycles. In the proposed modulation technique, the switching angles and the DC voltage levels are calculated off-line to eliminate more harmonics. Therefore, the DC voltage levels are not equal and should be regulated. To achieve this aim, a DC/DC converter is applied to adjust the DC link voltages with several capacitors. The effect of the new harmonic elimination technique on the output quality of several single phase multilevel converters is explained in chapter 3 and 6 of this thesis. According to the electrical model of high power ultrasound transducer, this device can be modelled as parallel combinations of RLC legs with a main capacitor. The impedance diagram of the transducer in frequency domain shows it has capacitive characteristics in almost all frequencies. Therefore, using a voltage source converter to drive a high power ultrasound transducer can create significant leakage current through the transducer. It happens due to significant voltage stress (dv/dt) across the transducer. To remedy this problem, LC filters are applied in some applications. For some applications such as ultrasound, using a LC filter can deteriorate the performance of the transducer by changing its characteristics and displacing the resonance frequency of the transducer. For such a case a current source converter could be a suitable choice to overcome this problem. In this regard, a current source converter is implemented and applied to excite the high power ultrasound transducer. To control the output current and voltage, a hysteresis control and unipolar modulation are used respectively. The results of this test are explained in chapter 7.

Improving sleep quality for patients after cardiac surgery

Research has consistently described that patients after cardiac surgery experience disturbed sleep yet there has been limited investigation into methods to improve this experience. Complementary therapies may be a method of addressing this issue. Aim: To determine if using progressive muscle relaxation improves self-rated sleep quality for patients following cardiac surgery. Methods and Results: Thirty-five participants' quantitative data on sleep quality were obtained via questionnaire during their first post-operative week after cardiac surgery. Qualitative data were obtained through written responses to open-ended questions. No significant differences in sleep quality scores were found between pre and post-intervention of progressive muscle relaxation using the Wilcoxon Signed Ranks Test. However, the qualitative analysis discovered the intervention aided some participants in initiating their sleep by diversion of thought, inducing relaxation or alleviating pain and anxiety. Conclusions: Qualitative findings suggest that progressive muscle relaxation may help patients who have undergone cardiac surgery initiate their sleep.

Factors associated with common mental disorders during the transition to adulthood : do emerging adults and ‘early starters’ differ? Findings from an Australian birth cohort study

Background: Despite increasing diversity in pathways to adulthood, choices available to young people are influenced by environmental, familial and individual factors, namely access to socioeconomic resources, family support and mental and physical health status. Young people from families with higher socioeconomic position (SEP) are more likely to pursue tertiary education and delay entry to adulthood, whereas those from low socioeconomic backgrounds are less likely to attain higher education or training, and more likely to partner and become parents early. The first group are commonly termed ‘emerging adults’ and the latter group ‘early starters’. Mental health disorders during this transition can seriously disrupt psychological, social and academic development as well as employment prospects. Depression, anxiety and most substance use disorders have early onset during adolescence and early adulthood with approximately three quarters of lifetime psychiatric disorders having emerged by 24 years of age. Aims: This thesis aimed to explore the relationships between mental health, sociodemographic factors and family functioning during the transition to adulthood. Four areas were investigated: 1) The key differences between emerging adults and ‘early starters’, were examined and focused on a series of social, economic, and demographic factors as well as DSM-IV diagnoses; 2) Methodological issues associated with the measurement of depression and anxiety in young adults were explored by comparing a quantitative measure of symptoms of anxiety and depression (Achenbach’s YSR and YASR internalising scales) with DSM-IV diagnosed depression and anxiety. 3) The association between family SEP and DSM-IV depression and anxiety was examined in relation to the different pathways to adulthood. 4) Finally, the association between pregnancy loss, abortion and miscarriage, and DSM-IV diagnoses of common psychiatric disorders was assessed in young women who reported early parenting, experiencing a pregnancy loss, or who had never been pregnant. Methods: Data were taken from the Mater University Study of Pregnancy (MUSP), a large birth cohort started in 1981 in Brisbane, Australia. 7223 mothers and their children were assessed five times, at 6 months, 5, 14 and 21 years after birth. Over 3700 young adults, aged 18 to 23 years, were interviewed at the 21-year phase. Respondents completed an extensive series of self-reported questionnaires and a computerised structured psychiatric interview. Three outcomes were assessed at the 21-year phase. Mental health disorders diagnosed by a computerised structured psychiatric interview (CIDI-Auto), the prevalence of DSM-IV depression, anxiety and substance use disorders within the previous 12-month, during the transition (between ages of 18 and 23 years) or lifetime were examined. The primary outcome “current stage in the transition to adulthood” was developed using a measure conceptually constructed from the literature. The measure was based on important demographic markers, and these defined four independent groups: emerging adults (single with no children and living with parents), and three categories of ‘early starter’, singles (with no children or partner, living independently), those with a partner (married or cohabitating but without children) and parents. Early pregnancy loss was assessed using a measure that also defined four independent groups and was based on pregnancy outcomes in the young women This categorised the young women into those who were never pregnant, women who gave birth to a live child, and women who reported some form of pregnancy loss, either an abortion or a spontaneous miscarriage. A series of analyses were undertaken to test the study aims. Potential confounding and mediating factors were prospectively measured between the child’s birth and the 21-year phase. Binomial and multinomial logistic regression was used to estimate the risk of relevant outcomes, and the associations were reported as odds ratios (OR) and 95% confidence intervals (95%CI). Key findings: The thesis makes a number of important contributions to our understanding of the transition to adulthood, particularly in relation to the mental health consequences associated with different pathways. Firstly, findings from the thesis clearly showed that young people who parented or partnered early fared worse across most of the economic and social factors as well as the common mental disorders when compared to emerging adults. That is, young people who became early parents were also more likely to experience recent anxiety (OR=2.0, 95%CI 1.5-2.8) and depression (OR=1.7, 95%CI 1.1-2.7) than were emerging adults after taking into account a range of confounding factors. Singles and those partnering early also had higher rates of lifetime anxiety and depression than emerging adults. Young people who partnered early, but were without children, had decreased odds of recent depression; this may be due to the protective effect of early marriage against depression. It was also found that young people who form families early had an increased risk of cigarette smoking (parents OR=3.7, 95%CI 2.9-4.8) compared to emerging adults, but not heavy alcohol (parents OR=0.4, 95%CI 0.3-0.6) or recent illicit drug use. The high rates of cigarette smoking and tobacco use disorders in ‘early starters’ were explained by common risk factors related to early adversity and lower SEP. Having a child and early marriage may well function as a ‘turning point’ for some young people, it is not clear whether this is due to a conscious decision to disengage from a previous ‘substance using’ lifestyle or simply that they no longer have the time to devote to such activities because of child caring. In relation to the methodological issues associated with assessing common mental disorders in young adults, it was found that although the Achenbach empirical internalising scales successfully predicted both later DSM-IV depression (YSR OR=2.3, 95%CI 1.7-3.1) and concurrently diagnosed depression (YASR OR=6.9, 95%CI 5.0- 9.5) and anxiety (YASR OR=5.1, 95%CI 3.8- 6.7), the scales discriminated poorly between young people with or without DSM-IV diagnosed mood disorder. Sensitivity values (the proportion of true positives) for the internalising scales were surprisingly low. Only a third of young people with current DSM-IV depression (range for each of the scales was between 34% to 42%) were correctly identified as cases by the YASR internalising scales, and only a quarter with current anxiety disorder (range of 23% to 31%) were correctly identified. Also, use of the DSM-oriented scales increased sensitivity only marginally (for depression between 2-8%, and anxiety between 2-6%) above the standard Achenbach scales. This is despite the fact that the DSM-oriented scales were originally developed to overcome the poor prediction of DSM-IV diagnoses by the Achenbach scales. The internalising scales, both standard and DSM-oriented, were much more effective at identifying young people with comorbid depression and anxiety, with OR’s 10.1 to 21.7 depending on the internalising scale used. SEP is an important predictor of both an early transition to adulthood and the experience of anxiety during that time Family income during adolescence was a strong predictor of early parenting and partnering before age 24 but not early independent living. Compared to families in the upper quintile, young people from families with low income were nearly twice as likely to live with a partner and four times more likely to become parents (OR ranged from 2.6 to 4.0). This association remained after adjusting for current employment and education level. Children raised in low income families were 30% more likely to have an anxiety disorder (OR=1.3, 95%CI 0.9-1.9), but not depression, as young adults when compared to children from wealthier families. Emerging adults and ‘early starters’ from low income families did not differ in their likelihood of having a later anxiety disorder. Young women reporting a pregnancy loss had nearly three times the odds of experiencing a lifetime illicit drug disorder (excluding cannabis) [abortion OR=3.6, 95%CI 2.0-6.7 and miscarriage OR=2.6, 95%CI 1.2-5.4]. Abortion was associated with alcohol use disorder (OR=2.1, 95%CI 1.3- 3.5) and 12-month depression (OR=1.9, 95%CI 1.1- 3.1). These finding suggest that the association identified by Fergusson et al between abortion and later psychiatric disorders in young women may be due to pregnancy loss and not to abortion, per se. Conclusion: Findings from this thesis support the view that young people who parent or partner early have a greater burden of depression and anxiety when compared to emerging adults. As well, young women experiencing pregnancy loss, from either abortion or miscarriage, are more likely to experience depression and anxiety than are those who give birth to a live infant or who have never been pregnant. Depression, anxiety and substance use disorders often go unrecognised and untreated in young people; this is especially true in young people from lower SEP. Early identification of these common mental health disorders is important, as depression and anxiety experienced during the transition to adulthood have been found to seriously disrupt an individual’s social, educational and economic prospects in later life.

Classifier selection using sequential error ratio criterion for multi-instance and multi-sample fusion

Classifier selection is a problem encountered by multi-biometric systems that aim to improve performance through fusion of decisions. A particular decision fusion architecture that combines multiple instances (n classifiers) and multiple samples (m attempts at each classifier) has been proposed in previous work to achieve controlled trade-off between false alarms and false rejects. Although analysis on text-dependent speaker verification has demonstrated better performance for fusion of decisions with favourable dependence compared to statistically independent decisions, the performance is not always optimal. Given a pool of instances, best performance with this architecture is obtained for certain combination of instances. Heuristic rules and diversity measures have been commonly used for classifier selection but it is shown that optimal performance is achieved for the `best combination performance' rule. As the search complexity for this rule increases exponentially with the addition of classifiers, a measure - the sequential error ratio (SER) - is proposed in this work that is specifically adapted to the characteristics of sequential fusion architecture. The proposed measure can be used to select a classifier that is most likely to produce a correct decision at each stage. Error rates for fusion of text-dependent HMM based speaker models using SER are compared with other classifier selection methodologies. SER is shown to achieve near optimal performance for sequential fusion of multiple instances with or without the use of multiple samples. The methodology applies to multiple speech utterances for telephone or internet based access control and to other systems such as multiple finger print and multiple handwriting sample based identity verification systems.

Are consumers fooled by discounts? An experimental test in a consumer search environment

In this article, we investigate experimentally whether people search optimally and how price promotions influence search behaviour. We implement a sequential search task with exogenous price dispersion in a baseline treatment and introduce discounts in two experimental treatments. We find that search behaviour is roughly consistent with optimal search but also observe some discount biases. If subjects do not know in advance where discounts are offered, the purchase probability is increased by 19 percentage points in shops with discounts, even after controlling for the benefit of the discount and for risk preferences. If consumers know in advance where discounts are given, then the bias is only weakly significant and much smaller (7 percentage points).

Self-reported likelihood of speeding : the effects of attitudes, personality, and perceived legitimacy of enforcement

The positive relationship between speed and crash risk and severity is robust and well-established. While excessive speeding is typically regarded by the public as a common contributing factor in road crashes, speeding remains a common traffic infringement and an arguably socially acceptable behaviour, particularly at low levels over the speed limit. This suggests that other factors potentially contribute to this disparity between crash perceptions and actual behaviours. Previous work has described associations between perceptions of the legitimacy of speed enforcement, attitudes, and how they relate to the likelihood of speeding. This study sought to more closely examine the nature of the relationships between these variables. In total, 293 Queensland drivers participated in a study that examined how demographics, personality variables, attitudes, and perceptions of the legitimacy of enforcement contributed to drivers’ self-reported likelihood of speeding. Results suggested that positive attitudes towards speeding had the greatest impact on likelihood of speeding behaviours. Being younger and higher levels of the personality trait of extraversion were also associated with greater levels of self-reported likelihood of speeding. Attitudes were found to mediate the relationship between perceived legitimacy of speed enforcement and self-reported likelihood of speeding. A subgroup analysis of participants with positive and negative attitudes towards speeding revealed that a differential set of variables were predictive of self-reported likelihood of speeding for the two subgroups. This highlights the potential importance of attitudes in understanding the influence of perceptions of legitimacy of speed enforcement on speeding behaviour, and the need for targeted rather than a ‘one size fits all’ approach to changing attitudes and ultimately behaviour. The findings of the current study help to further understand why some drivers continue to speed.

Determinants of drink-driving and association between drink-driving and road traffic fatalities in Ghana

Aim The objective is to establish determinants of drink-driving and its association with traffic crashes in Ghana. Methods A multivariable logistic regression was used to establish significant determinants of drink-driving and a bivariate logistic regression to establish the association between drink–driving and road traffic crashes in Ghana. Results In total, 2,736 motorists were randomly stopped for breath testing of whom 8.7% tested positive for alcohol. Among the total participants, 5.5% exceeded the legal BAC limit of 0.08%. Formal education is associated with a reduced likelihood of drink-driving compared with drivers without formal education. The propensity to drink-drive is 1.8 times higher among illiterate drivers compared with drivers with basic education. Young adult drivers also recorded elevated likelihoods for driving under alcohol impairment compared with adult drivers. The odds of drink-driving among truck drivers is OR=1.81, (95% CI=1.16 to 2.82) and two wheeler riders is OR=1.41, (95% CI=0.47 to 4.28) compared with car drivers. Contrary to general perception, commercial car drivers have a significant reduced likelihood of 41%, OR=0.59, (95% CI=0.38 to 0.92) compared with the private car driver. Bivariate analysis conducted showed a significant association between the proportion of drivers exceeding the legal BAC limit and road traffic fatalities, p<0.001. The model predicts a 1% increase in the proportion of drivers exceeding the legal BAC to be associated with a 4% increase in road traffic fatalities, 95% CI= 3% to 5% and vice versa. Conclusion A positive and significant association between roadside alcohol prevalence and road traffic fatality has been established. Scaling up roadside breath test, determining standard drink and disseminating to the populace and formulating policies targeting the youth such as increasing minimum legal drinking age and reduced legal BAC limit for the youth and novice drivers might improve drink-driving related crashes in Ghana.