Wind Shear, Gust, and Yaw-Induced Dynamic Stall on Wind-Turbine Blades

This study examined the effect of a spanwise angle of attack gradient on the growth and stability of a dynamic stall vortex in a rotating system. It was found that a spanwise angle of attack gradient induces a corresponding spanwise vorticity gradient, which, in combination with spanwise flow, results in a redistribution of circulation along the blade. Specifically, when modelling the angle of attack gradient experienced by a wind turbine at the 30% span position during a gust event, the spanwise vorticity gradient was aligned such that circulation was transported from areas of high circulation to areas of low circulation, increasing the local dynamic stall vortex growth rate, which corresponds to an increase in the lift coefficient, and a decrease in the local vortex stability at this point. Reversing the relative alignment of the spanwise vorticity gradient and spanwise flow results in circulation transport from areas of low circulation generation to areas of high circulation generation, acting to reduce local circulation and stabilise the vortex. This circulation redistribution behaviour describes a mechanism by which the fluctuating loads on a wind turbine are magnified, which is detrimental to turbine lifetime and performance. Therefore, an understanding of this phenomenon has the potential to facilitate optimised wind turbine design.

Monitoring of Dynamic Bridge Behaviour Using Digital Image Correlation

Bridges are a critical part of North America’s transportation network that need to be assessed frequently to inform bridge management decision making. Visual inspections are usually implemented for this purpose, during which inspectors must observe and report any excess displacements or vibrations. Unfortunately, these visual inspections are subjective and often highly variable and so a monitoring technology that can provide quantitative measurements to supplement inspections is needed. Digital Image Correlation (DIC) is a novel monitoring technology that uses digital images to measure displacement fields without any contact with the bridge. In this research, DIC and accelerometers were used to investigate the dynamic response of a railway bridge reported to experience large lateral displacements. Displacements were estimated using accelerometer measurements and were compared to DIC measurements. It was shown that accelerometers can provide reasonable estimates of displacement for zero-mean lateral displacements. By comparing measurements in the girder and in the piers, it was shown that for the bridge monitored, the large lateral displacements originated in the steel casting bearings positioned above the piers, and not in the piers themselves. The use of DIC for evaluating the effectiveness of rehabilitation of the LaSalle Causeway lift bridge in Kingston, Ontario was also investigated. Vertical displacements were measured at midspan and at the lifting end of the bridge during a static test and under dynamic live loading. The bridge displacements were well within the operating limits, however a gap at the lifting end of the bridge was identified. Rehabilitation of the bridge was conducted and by comparing measurements before and after rehabilitation, it was shown that the gap was successfully closed. Finally, DIC was used to monitor the midspan vertical and lateral displacements in a monitoring campaign of five steel rail bridges. DIC was also used to evaluate the effectiveness of structural rehabilitation of the lateral bracing of a bridge. Simple finite element models are developed using DIC measurements of displacement. Several lessons learned throughout this monitoring campaign are discussed in the hope of aiding future researchers.

Comprehensive Characterization of Measurement Data Gathered by the Pressure Tube to Calandria Tube Gap Probe

Multi-frequency eddy current measurements are employed in estimating pressure tube (PT) to calandria tube (CT) gap in CANDU fuel channels, a critical inspection activity required to ensure fitness for service of fuel channels. In this thesis, a comprehensive characterization of eddy current gap data is laid out, in order to extract further information on fuel channel condition, and to identify generalized applications for multi-frequency eddy current data. A surface profiling technique, generalizable to multiple probe and conductive material configurations has been developed. This technique has allowed for identification of various pressure tube artefacts, has been independently validated (using ultrasonic measurements), and has been deployed and commissioned at Ontario Power Generation. Dodd and Deeds solutions to the electromagnetic boundary value problem associated with the PT to CT gap probe configuration were experimentally validated for amplitude response to changes in gap. Using the validated Dodd and Deeds solutions, principal components analysis (PCA) has been employed to identify independence and redundancies in multi-frequency eddy current data. This has allowed for an enhanced visualization of factors affecting gap measurement. Results of the PCA of simulation data are consistent with the skin depth equation, and are validated against PCA of physical experiments. Finally, compressed data acquisition has been realized, allowing faster data acquisition for multi-frequency eddy current systems with hardware limitations, and is generalizable to other applications where real time acquisition of large data sets is prohibitive.

From science gateways to commercial solutions

The European CloudSME project that incorporated 24 European SMEs, besides five academic partners, has finished its funded phase in March 2016. This presentation will provide a summary of the results of the project, and will analyze the challenges and differences when developing “SME Gateways”, when compared to “Science Gateways”. CloudSME started in 2013 with the aim to develop a cloud-based simulation platform for manufacturing and engineering SMEs. The project was based around industry use-cases, five of which were incorporated in the project from the start, and seven additional ones that were added as an outcome of an open call in January 2015. CloudSME utilized science gateway related technologies, such as the commercial CloudBroker Platform and the WS-PGRADE/gUSE Gateway Framework that were developed in the preceding SCI-BUS project. As most important outcome, the project successfully implemented 12 industry quality demonstrators that showcase how SMEs in the manufacturing and engineering sector can utilize cloud-based simulation services. Some of these solutions are already market-ready and currently being rolled out by the software vendor companies. Some others require further fine-tuning and the implementation of commercial interfaces before being put into the market. The CloudSME use-cases came from a very wide application spectrum. The project implemented, for example, an open marketplace for micro-breweries to optimize their production and distribution processes, an insole design validation service to be used by podiatrists and shoe manufacturers, a generic stock management solution for manufacturing SMEs, and also several “classical” high-performance computing case-studies, such as fluid dynamics simulations for model helicopter design, and dual-fuel internal combustion engine simulation. As the project generated significant impact and interest in the manufacturing sector, 10 CloudSME stakeholders established a follow-up company called CloudSME UG for the future commercialization of the results. Besides the success stories, this talk would also like to highlight the difficulties when transferring the outcomes of an academic research project to real commercial applications. The different mindset and approach of academic and industry partners presented a real challenge for the CloudSME project, with some interesting and valuable lessons learnt. The academic way of supporting SMEs did not always work well with the rather different working practices and culture of many participants. Also, the quality of support regarding operational solutions required by the SMEs is well beyond the typical support services academic institutions are prepared for. Finally, a clear lack of trust in academic solutions when compared to commercial solutions was also imminent. The talk will highlight some of these challenges underpinned by the implementation of the CloudSME use-cases.

Aerodynamic optimization using Adjoint methods and parametric CAD models

This paper describes an implementation of a method capable of integrating parametric, feature based, CAD models based on commercial software (CATIA) with the SU2 software framework. To exploit the adjoint based methods for aerodynamic optimisation within the SU2, a formulation to obtain geometric sensitivities directly from the commercial CAD parameterisation is introduced, enabling the calculation of gradients with respect to CAD based design variables. To assess the accuracy and efficiency of the alternative approach, two aerodynamic optimisation problems are investigated: an inviscid, 3D, problem with multiple constraints, and a 2D high-lift aerofoil, viscous problem without any constraints. Initial results show the new parameterisation obtaining reliable optimums, with similar levels of performance of the software native parameterisations. In the final paper, details of computing CAD sensitivities will be provided, including accuracy as well as linking geometric sensitivities to aerodynamic objective functions and constraints; the impact in the robustness of the overall method will be assessed and alternative parameterisations will be included.

Rational O(2)–Equivariant Spectra

The category of rational O(2)-equivariant cohomology theories has an algebraic model A(O(2)), as established by work of Greenlees. That is, there is an equivalence of categories between the homotopy category of rational O(2)-equivariant spectra and the derived category of the abelian model DA(O(2)). In this paper we lift this equivalence of homotopy categories to the level of Quillen equivalences of model categories. This Quillen equivalence is also compatible with the Adams short exact sequence of the algebraic model.

Neuartiges Modell des Querverhaltens von FFZ-Reifen

Die dynamische Standsicherheit ist beim Betrieb eines Gegengewichtsgabelstaplers eine entscheidende Größe. Diese wird neben der Position des Gesamtschwerpunktes und den geometrischen Abmaßen wesentlich von den Reifeneigenschaften bestimmt. Ein neues Rechenmodell der Super-Elastik-Reifen ermöglicht genauere Simulationen, tiefere Einblicke in das dynamische Verhalten der Fahrzeuge bei der Auslegung und somit bessere dynamische Standsicherheit.

Untersuchungen Gewichtsreduktionspotentiale Gegengewichtsgabelstapler

Die Masse eines Gegengewichtstaplers beeinflusst den Energieverbrauch beim Fahren maßgeblich. Steigende Energiepreise und steigendes Umweltbewusstsein führen zu grünen Trends in Logistik. Durch Reduktion der Gesamtmasse eines Gabelstaplers können große Einsparungen erreicht werden. Eine Machbarkeitsstudie soll mithilfe der numerischen Simulationen zeigen, dass neuartige Fahrzeuge mit aktiven Systemen trotz geringerer Masse hinreichend hohe Standsicherheit aufweisen können. In diesem Beitrag sollen die ersten Ergebnisse dieses Forschungsvorhabens vorgestellt werden.

Einsatz faser- bzw. textilverstärkter Verbundwerkstoffe

Die hohen Leistungsansprüche an moderne Lagersysteme führen zu immer kürzeren Taktzeiten beim Warenumschlag, die auch von Regalbediengeräten (RBG) realisiert werden müssen. Um trotz der kurzen Umschlagzeiten eine schnelle und sichere Gutübergabe zu gewährleisten, muss innerhalb der Ausschwingzeit die Amplitude der Schwingungen des Lastaufnahmemittels vor dem Ein- beziehungsweise Auslagerungsvorgang weitgehend abgeklungen sein. Diese Wartezeiten beeinflussen die Taktzeit und damit die Umschlagleistung des RBG negativ. Ein möglicher Ansatz, die Ausschwingzeiten zu verkürzen, ist der Einsatz hochdämpfender Materialien, wie etwa Verbundwerkstoffe. Durch die erreichte Reduzierung der Schwingungsamplituden bei gleichzeitiger Erhöhung des Leichtbaugrades ist eine deutliche Effizienzsteigerung von RBG zu erwarten.

SISAL - Um sistema supervisório para elevação artificial de petróleo

MEDEIROS, Adelardo A. D. et al. SISAL - Um Sistema Supervisório para Elevação Artificial de Petróleo. In: Rio Oil and Gas Expo Conference, 2006, Rio de Janeiro, RJ. Anais... Rio de Janeiro, 2006.

Sneakerheads and Custom Kicks: Insights into Symbolic Mass Customization

This chapter presents an exploratory study involving a group of athletic shoe enthusiasts and their feelings towards customized footwear. These "sneakerheads" demonstrate their infatuation with sneakers via activities ranging from creating catalogs of custom shoes to buying and selling rare athletic footwear online. The key characteristic these individuals share is that, for them, athletic shoes are a fundamental fashion accessory stepped in symbolism and meaning. A series of in-depth interviews utilizing the Zaltman Metaphor Elicitation Technique (ZMET) provide a better understanding of how issues such as art, self-expression, exclusivity, peer recognition, and counterfeit goods interact with the mass customization of symbolic products by category experts.

Sesamoids of the metatarsophalangeal joint of the big toe: a sistematic review

Abstract: The first metatarsal sesamoid bones are not always taken into consideration when making a diagnosis, in pathologies that affect the region of the first metatarsal head. This is due to the insufficient knowledge of all the pathologies that can affect the sesamoids and the relative little incidence that they have. With the increment of sports activities, in particular the running, increasingly affects of the symptoms concerning this region are observed. Methods: A literature search was performed in 5 databases (Medline, PubMed, Scopus, Cochrane Library and BUCEA). The terms included in the search were: sesamoids, anatomy, biomechanics, sesamoids review and sesamoids pathology. In the initial search articles with no more than 10 years, only humans and revision texts are considered. Results: 24 articles were selected and include different pathologies with diagnosis using imaging tests and treatments, both conservative and surgical; as well as aspects from the biomechanics of the metatarsal-sesamoid joint. Conclusion: Sesamoids due of his anatomy, topography and function can be involved in a lot of pathologies; with similar signs and symptoms that can confuse the podiatry when he has to make a correct diagnosis or treatment.

Contact dermatitis from shoes: an update

Contact dermatitis is a common inflammatory skin condition characterized by erythematous and pruritic skin lesions that occur after contact with a foreign substance. There are two forms of contact dermatitis: irritant and allergic. Irritant contact dermatitis is caused by the non–immune-modulated irritation of the skin by a substance, leading to skin changes. Allergic contact dermatitis is a delayed hypersensitivity reaction in which a foreign substance comes into contact with the skin; skin changes occur after reexposure to the substance. A medical condition referred to as “shoe dermatitis” is a form of contact dermatitis caused by the contact of the foot with parts of the shoe due to these materials. Shoe dermatitis is a diagnostic and therapeutic challenge and is a common type of contact dermatitis. It is imperative the foot and ankle physician become familiar with recognizing signs and symptoms of shoe dermatitis so that their patients can be accurately diagnosis and appropriately treated to avoid secondary infections and disability. This review will first present causative factors for the etiology of shoe contact dermatitis supported by clinical-based evidence as found in the medical literature. Secondly, a description of the signs and symptoms of shoe contact dermatitis will be presented in a narrative fashion. Finally, both treatment options and preventative measures to avoid shoe.

Essays on Machine Learning and Hedonic Models

Thesis (Ph.D.)--University of Washington, 2016-08

Princípios Lean aplicados à gestão da informação: um caso prático no departamento de custeio da ECCO

O pensamento lean, assim como os conceitos e práticas que lhe estão associados, são, hoje em dia, vistos pelas organizações como meios que promovem a busca pela excelência empresarial. A aplicação dos princípios lean ultrapassou já a barreira do domínio produtivo, conhecendo-se, cada vez mais, outros ramos de utilização, como é o caso do setor dos serviços, que tem demonstrado um potencial enorme no que diz respeito à exploração desta filosofia. No entanto, as experiências de aplicação destes princípios a outras áreas, que não a indústria de transformação, têm ainda poucos resultados concretos espelhados na literatura. Este projeto surge no sentido de contribuir para alcançar processos mais eficientes, aplicando ferramentas e metodologias da filosofia lean a processos de gestão da informação, tendo o caso prático decorrido no recém-criado Departamento de Custeio Global da ECCO. Por se tratar de um novo departamento, ergue-se a necessidade de construir e modificar ferramentas e práticas em toda a estrutura da empresa. Deste modo, o lean será utilizado como um possível caminho para promover a melhoria contínua dos vários processos, tendo em vista a obtenção de uma melhor relação entre os resultados obtidos e os recursos despendidos. Assim, serão apresentadas várias propostas de melhoria para o departamento em causa, no âmbito da gestão da informação e que, partindo de uma análise inicial baseada nos princípios lean, pretendem agregar mais valor aos processos, minimizando os desperdícios que lhes estão associados e, consequentemente, promovendo o seu melhoramento contínuo.