PCB-integrated optical waveguide sensors: An ammonia gas sensor

This paper presents a novel platform for the formation of cost-effective PCB-integrated optical waveguide sensors. The sensor design relies on the use of multimode polymer waveguides that can be formed directly on standard PCBs and commercially-available chemical dyes, enabling the integration of all essential sensor components (electronic, photonic, chemical) on low-cost substrates. Moreover, it enables the detection of multiple analytes from a single device by employing waveguide arrays functionalised with different chemical dyes. The devices can be manufactured with conventional methods of the PCB industry, such as solder-reflow processes and pick-and-place assembly techniques. As a proof of principle, a PCB-integrated ammonia gas sensor is fabricated on a FR4 substrate. The sensor operation relies on the change of the optical transmission characteristics of chemically functionalised optical waveguides in the presence of ammonia molecules. The fabrication and assembly of the sensor unit, as well as fundamental simulation and characterisation studies, are presented. The device achieves a sensitivity of approximately 30 ppm and a linear response up to 600 ppm at room temperature. Finally, the potential to detect multiple analytes from a single device is demonstrated using principal-component analysis. © 1983-2012 IEEE.

Optimizing the energy offset between dye and hole-transporting material in solid-state dye-sensitized solar cells

The power-conversion efficiency of solid-state dye-sensitized solar cells can be optimized by reducing the energy offset between the highest occupied molecular orbital (HOMO) levels of dye and hole-transporting material (HTM) to minimize the loss-in-potential. Here, we report a study of three novel HTMs with HOMO levels slightly above and below the one of the commonly used HTM 2,2′,7,7′- tetrakis(N,N-di-p-methoxyphenylamino)-9,9′- spirobifluorene (spiro-OMeTAD) to systematically explore this possibility. Using transient absorption spectroscopy and employing the ruthenium based dye Z907 as sensitizer, it is shown that, despite one new HTM showing a 100% hole-transfer yield, all devices based on the new HTMs performed worse than those incorporating spiro-OMeTAD. We further demonstrate that the design of the HTM has an additional impact on the electronic density of states present at the TiO2 electrode surface and hence influences not only hole- but also electron-transfer from the sensitizer. These results provide insight into the complex influence of the HTM on charge transfer and provide guidance for the molecular design of new materials. © 2013 American Chemical Society.

Low-cost PCB-integrated polymer waveguide sensor for gas detection

An optical waveguide sensor formed directly on low-cost PCB substrates is presented for the first time. The device integrates polymer waveguides functionalized with chemical dyes, photonic and electronic components and allows multiple-gas detection. © OSA/CLEO 2011.

基于核酸特殊结构的分子识别及核酸相关纳米结构的设计应用

核酸为生命的最基本物质之一，是生物体遗传信息的携带者，在生长、遗传、变异等一系列重大生命现象中起决定性的作用。以核酸作为新药设计的靶分子，越来越受到人们的广泛重视。然而，不像其它靶分子如蛋白质、受体等具有特定的结构和功能，核酸结构在很多情况下是同源的，而且联系到很多人体正常的生理功能；能够与核酸结合的药物又往往不具有序列选择性，这就带来明显的毒副作用。因此，寻找和发现一些与疾病相关的核酸的特殊结构，并筛选对其有特异性结合能力的小分子，是以核酸为靶的药物研究的一个重要课题。 近年来，随着纳米科学技术的兴起，以核酸作为纳米体系的结构材料开始受到人们的广泛关注。作为一类特殊的线性高分子，核酸具有化学性质稳定，结构丰富且可控，良好的刚性和柔性，精确识别，高度生物相容性，合成方便等诸多优点，是一类优良的结构材料。目前核酸相关的纳米组装结构和器件研究还处于起步阶段，但是已经呈现出良好的发展前景。 本论文主要针对核酸特殊结构的分子识别及核酸相关功能纳米结构的设计这两方面展开了研究，全文由以下两大部分组成： 第一部分通过光谱学和生物化学等手段，研究了小分子对不同核酸结构的识别作用。借助于竞争平衡透析技术，发现一类恶嗪染料(oxazine dyes)能够与多种结构核酸结合。热变性及光谱实验结果表明，oxazine染料能够诱导杂合体三链核酸poly(rA):2poly(dT)的形成，并强烈地稳定其结构，其中以cresyl violet作用最强，是迄今发现的化合物中最强的。进一步研究发现，此类化合物以嵌插方式与杂合体三链核酸结合。RNase H酶切实验表明，杂合体三链核酸的形成能够强烈地抑制RNase H核酸酶的活性。研究了oxazine-170与三链核酸poly(dA):2poly(dT)及poly(rA):2poly(rU)的相互作用，发现oxazine-170能够强烈稳定三链DNA poly(dA):2poly(dT)的结构，而对相应双链DNA不具稳定作用；对三链RNA poly(rA):2poly(rU)及相应的双链RNA都有一定稳定作用，但作用不强。进一步研究发现，oxazine-170能够以两种结合方式与核酸结合：嵌插方式和外部静电堆积作用。研究了oxazine-170及cresyl violet与单链核酸的相互作用。研究发现oxazine-170能够序列特异性地与单链核酸poly(rA) 结合，CD光谱及AFM研究发现oxazine-170诱导poly(rA)形成新的二级结构。UV光谱、FL光谱及RLS研究发现poly(rA)促使oxazine 170形成H-aggregate，并以poly(rA)为模板自组装。而cresyl violet能够与单链核酸poly(rA)及poly(dA)结合，且采用不同的结合方式： cresyl violet能够与oxazine-170 类似地以poly(rA)为模板自组装；以嵌插方式与poly(dA)结合，并诱导其单链碱基堆积方式的改变。通过以上实验结果，我们进一步揭示了oxazine染料作为肿瘤细胞染色及光动力学治疗试剂的结构基础，对进一步设计、合成更加高效的抗肿瘤药物具有一定的指导意义。 第二部分中，我们尝试设计了几种基于核酸的纳米结构功能体系，并讨论了其相关应用。利用有机小分子coralyne能够诱导聚腺嘌呤序列反平行双链结构的形成，实现了一类新型的小分子诱导的纳米金组装结构。并以(dA)16功能化的金纳米粒子作为新型纳米探针，发展了一种简单的筛选单链核酸聚腺嘌呤序列结合分子的筛选方法。利用核酸限制性内切酶酶切位点回文序列的结构特点，设计了一种以DNA功能化的金纳米粒子组装体为酶切底物的比较通用的核酸限制性内切酶活力检测方法，并进一步用于甲基化酶活性检测及其抑制剂的筛选。基于单链DNA富胞嘧啶i-motif结构在不同pH值条件下的形成与解离，设计了一类质子驱动的DNA分子镊子，与基于链交换反应的DNA分子镊子相比，该体系更加简单，工作效率更高。随后，我们又通过合理设计，得到了两种分别能够结合与释放DNA和蛋白的分子镊子，为其应用做了一些探索。

染料脱色菌株筛选及染料脱色作用研究

染料废水成分复杂，色度高，是主要的环境污染源之一。应用微生物对染料废水脱色具有处理费用低和操作管理方便等优势，具有较好的发展前景。 本文采用筛选到一株短刺小克银汉霉(Cuuninghamella echinulata) KM3及一株红酵母(Rhodotorula sp.)YR-1分别对偶氮染料刚果红废水和酸性红废水进行了脱色研究，同时利用KM3及YR-1组成的复合菌种脱色体系对酸性红废水进行了脱色实验，为染料脱色真菌的应用奠定了基础。 KM3形成的菌丝球对多种染料具有较好脱色效果。KM3最适菌丝球形成条件：pH6-7、装液量90ml、孢子悬液浓度105个/ml (接种5ml)、摇床转速120rpm、培养温度30℃、培养时间72h；成球机理为凝聚型发育。KM3菌丝球对刚果红最佳脱色条件为：染料溶液初始pH值7.0，温度为33℃，摇床转速为120rpm。在刚果红50~200mg/l 浓度范围内， KM3菌丝球对刚果红吸附脱色动力学可用拟二级动力学方程描述。菌丝球对刚果红的吸附行为符合Langmuir和Freundlich 等温方程模型，Langmuir方程能更好的描述菌丝球对刚果红的吸附行为。丙酮对刚果红的解吸率最高，其解吸动力学过程符合二级动力学方程。将KM3应用在真菌生物滤床反应器中，在非灭菌和灭菌情况下接种孢子悬液后处理刚果红废水的过程中，均需长时间挂膜，处理效果一般。反应器中投加菌丝球后处理刚果红废水在3小时内达到92%以上的脱色效果。 YR-1对酸性红脱色机制属于降解脱色。YR-1对酸性红的最佳脱色培养条件为：初始pH 5.0、接种量5%、温度30℃；最佳碳源是葡萄糖，其次是蔗糖；最佳氮源是酵母膏或蛋白胨。在替换分批脱色实验和连续补料脱色实验中，脱色率一直保持在75%以上，显示YR-1在上述脱色体系中均具有良好适应性。 在三种复合菌种对酸性红的脱色体系中，体系Ⅲ（菌丝球与海藻酸钠固定化的酵母细胞混合培养）的脱色效果可达98%以上。对该体系而言，3种粒径固定化酵母小球（Ø1.1mm、1.8mm、3.1mm）中Ø1.8mm、3.1mm小球脱色率较为理想，而酵母细胞初始密度对脱色效果的影响不大。 KM3、YR-1分别具有处理刚果红废水和酸性红废水的应用前景，而KM3与YR-1联合应用对酸性红的脱色效果更好。

Synthesis and characterization of carbon black supported Pt-Ru alloy as a model catalyst for fuel cells

A set of bimetallic Pt-Ru catalysts prepared by co-impregnation of carbon black with ruthenium(III) chloride hydrate and hydrogen hexachloroplatinate(IV) hydrate were investigated by temperature-programmed reduction (TPR), chemisorption of hydrogen, transmission electron microscopy (TEM), microcalorimetry of adsorbed CO and a structure-sensitive reaction (n-hexane conversion). The results showed that the volumetric capacities for CO and H-2 adsorption is influenced in the bimetallic Pt-Ru catalysts by the formation of a Pt-Ru alloy. The n-hexane reaction revealed that the reaction mechanism for the pure Pt catalyst mainly occurs via cyclic isomerization and aromatization due to the presence of bigger Pt surface ensembles, whereas the Pt-Ru catalysts exhibited predominantly bond-shift isomerization by the diluting effect of Ru metal addition. The differential heats of CO chemisorption on Pt-Ru catalysts fell between the two monometallic Pt and Ru catalysts extremes. (C) 2004 Elsevier B.V. All rights reserved.

Studies on state and structure of noble metals in electrocatalyst made by coprecipitation method

The electrocatalysts of Pt/C, PtRu/C and Ru/C were prepared by the impregnation method. The facet characterization, the dispersion and the particle size for the catalysts were determined by means of X-ray diffraction and transmission electron microscopy. X-ray photoelectron spectroscopy was also used to analyze the state and the valency of the noble metals. The results show that the particle size was in nanometer range and the binary metals have come into being an alloy. The platinum in the catalysts existed in zero valency. The valency of the ruthenium on the surface is different from that in the body, while the ruthenium on the surface existed in oxide-form. PtRu/C and Pt/C are of good activity to the electrooxidation of hydrogen except Ru/C. PtRu/C is more tolerant of CO than Pt/C, and CO is only adsorbed on Pt.

Ammonia synthesis on graphitic-nanofilament supported Ru catalysts

Graphitic-nanofilaments (GNFs) supported ruthenium catalysts were prepared and characterized by NZ physisorption, X-ray diffraction (XRD), transmission electron microscope (TEM) and temperature programmed reduction-mass spectroscopy (TPR-MS) and used for ammonia synthesis in a fixed bed microreactor. The TEMs of the Ru/GNFs and Ru-Ba/GNFs catalysts indicate that the Ru particles are in the range of 2-4 nm, which is the optimum size of Ru particles for the maximum number of B5 type sites. The activity of Ru-Ba/GNFs catalysts is higher than that of Ru-Ba/AC by about 25%. The methanation reaction on the Ru/GNFs catalyst is remarkably inhibited compared with a Ru/AC catalyst. High graphitization of GNFs is likely to be the reason for the high resistance to the methanation reaction. The power rate law for ammonia synthesis on Ru-Ba/GNFs catalysts can be expressed by r = Kp(NH3)(-0.4) P-N2(0.8) P-H2(-0.7), indicating that H-2 is an inhibitor for N-2 activation on the catalyst. Catalysts with the promoters Ba, K and Cs show large differences in activity for ammonia synthesis. The catalyst promoted with Ba (Ba/Ru = 0.2 molar ratio) was found to be the most active, whereas that with a K promoter was the least active. (C) 2003 Elsevier B.V. All rights reserved.

Separation and detection of chlorpromazine hydrochloride and promethazine hydrochloride using electrochemiluminescence followed by capillary electrophoresis

Phenothiazine drugs, chlorpromazine hydrochloride (CPZ) and promethazine hydrochloride (PMZ), were determined with Ru(bpy)(3)(2+) electrochemiluminescene by the capillary electrophoresis (CE-ECL). It was found that both CPZ and PMZ could produce an intermediate that acted as coreactants to react with Ru(bpy)(3)(2+) to produce excited states which were capable of emitting light. This CE-ECL detection method had high sensitivity, good selectivity and reproducibility for CPZ and PMZ determination.

The synthesis and characterization of novel liquid crystalline, meso-tetra[4-(3,4,5-trialkoxybenzoate)phenyl]porphyrins

Five, novel, meso-tetra[4-(3,4,5-trialkoxybenzoate)phenyl]porphyrins and their metal complexes were synthesized and their molecular structures were confirmed by H-1 NMR, FTIR spectroscopy and elemental analysis. Mesomorphic studies using DSC, polarizing optical microscope and X-ray diffraction revealed that all compounds exhibited thermotropic columnar mesophases over a wide mesophase temperature range and low liquid crystalline-crystal line transition temperature. (c) 2007 Elsevier Ltd. All rights reserved

Tetrahydrothiophenium-based ionic liquids for high efficiency dye-sensitized solar cells

Binary melts of S-ethyltetrahydrothiophenium iodide and dicyanoamide (or tricyanomethide) have been employed for dye-sensitized solar cells with high power conversion efficiencies up to 6.9% under the illumination of AM 1.5G full sunlight. We have further shown that the transport of triiodide in ionic liquids with high iodide concentration is viscosity-dependent in terms of a physical diffusion coupled bond exchange mechanism apart from the simple physical diffusion.

New Efficiency Records for Stable Dye-Sensitized Solar Cells with Low-Volatility and Ionic Liquid Electrolytes

We report a high molar extinction coefficient heteroleptic polypyridyl ruthenium sensitizer, featuring an electron-rich 3,4-ethylenedioxythiophene unit in its ancillary ligand. A nanocrystalline titania film stained with this sensitizer shows an improved optical absorption, which is highly desirable for practical dye-sensitized solar cells with a thin photoactive layer, facilitating the efficient charge collection.

New Organic Sensitizer for Stable Dye-Sensitized Solar Cells with Solvent-Free Ionic Liquid Electrolytes

We report a high molar extinction coefficient metal-free sensitizer composed of a triarylamine donor in combination with the 2-(2,2'-bithiophen-5-yl)acrylonitrile conjugation unit and cyanoacrylic acid as an acceptor. In conjugation with a volatile acetonitrile-based electrolyte or a solvent-free ionic liquid electrolyte, we have fabricated efficient dye-sensitized solar cells showing a corresponding 7.5% or 6.1% efficiency measured under the air mass 1.5 global sunlight. The ionic liquid cell exhibits excellent stability during a 1000 h accelerated test under the light-soaking and thermal dual stress. Intensity-modulated photocurrent and photovolatge spectroscopies were employed along with the transient photoelectrical decay measurements to detail the electron transport in the mesoporous titania films filled with these two electrolytes.