Estudo de massa cerâmica triaxial visando à otimização do ciclo de queima da indústria de cerâmica estrutural

Over recent years the structural ceramics industry in Brazil has found a very favorable market for growth. However, difficulties related to productivity and product quality are partially inhibiting this possible growth. An alternative for trying to solve these problems and, thus, provide the pottery industry the feasibility of full development, is the substitution of firewood used in the burning process by natural gas. In order to contribute to this process of technological innovation, this paper studies the effect of co-use of ceramic phyllite and kaolin waste on the properties of a clay matrix, verifying the possible benefits that these raw materials can give to the final product, as well as the possibility of such materials to reduce the heat load necessary to obtain products with equal or superior quality. The study was divided into two steps: characterization of materials and study of formulations. Two clays, a phyllite and a residue of kaolin were characterized by the following techniques: laser granulometry, plasticity index by Atterberg limits, X-ray fluorescence, X-ray diffraction, mineralogical composition by Rietveld, thermogravimetric and differential thermal analysis. To study the formulations, specifically for evaluation of technological properties of the parts, was performed an experimental model that combined planning involving a mixture of three components (standard mass x phyllite x kaolin waste) and a 23 factorial design with central point associated with thermal processing parameters. The experiment was performed with restricted strip-plot randomization. In total, 13 compositional points were investigated within the following constraints: phyllite ≤ 20% by weight, kaolin waste ≤ 40% by weight, and standard mass ≥ 60% by weight. The thermal parameters were used at the following levels: 750 and 950 °C to the firing temperature, 5 and 15 °C/min at the heating rate, 15 and 45min to the baseline. The results showed that the introduction of phyllite and/or kaolin waste in ceramic body produced a number of benefits in properties of the final product, such as: decreased absorption of water, apparent porosity and linear retraction at burn; besides the increase in apparent specific mass and mechanical properties of parts. The best results were obtained in the compositional points where the sum of the levels of kaolin waste and phyllite was maximal (40% by weight), as well as conditions which were used in firing temperatures of 950 °C. Regarding the prospect of savings in heat energy required to form the desired microstructure, the phyllite and the residue of kaolin, for having small particle sizes and constitutions mineralogical phases with the presence of fluxes, contributed to the optimization of the firing cycle.

A concepção estrutural como expressão plástica: um olhar tectônico sobre arquitetura em madeira

This work regards to the structural conception as a formal element of design in wood architecture. On this approach, the group of projects studied is formed by some realized works of two important Brazilian architects: Severiano Porto and Marcos Acayaba. The time interval comprises the period from 1971 to 1997, which correspond respectively to the years of the creation of first and the last of the analyzed constructions. The research perspective concerns to the relationship between the parts, the whole and the building techniques adopted in each project. Moreover, the analysis focuses on the structure as the link among the different projectual ideas. Thus, the research method firstly includes a survey of specific bibliographies and documents which refer to the structural conception in wood architecture. Secondly,the buildings are analyzed according to the methods of architectural composition discussed through this work.

Efeito da tecnologia de microondas nas propriedades tecnológicas dos componentes de cerâmica estrutural

O processamento térmico de materiais cerâmicos via energia de microondas, no estágio atual, vem ganhando cada dia mais importância, tendo em vista suas inúmeras aplicações, como por exemplo: aplicação de microondas na área de processamento mineral (aquecimento de minérios antes da moagem, secagem, redução carbotérmica de óxidos minerais, lixiviação, fusão, pré-tratamento de minérios e concentrados de ouro refratário, regeneração de carvão, etc. de acordo com Kigman & Rowson, 1998). Em virtude de uma série de vantagens em potencial, frente aos métodos convencionais de aquecimento, como redução no tempo de processamento; economia de energia; diminuição do diâmetro médio das partículas e melhoramento nas propriedades tecnológicas em geral, esta tecnologia vem se destacando. Neste contexto, o objetivo geral deste trabalho, é desenvolver uma pesquisa visando identificar e caracterizar novas opções de matérias-primas cerâmicas como argilas, feldspatos e caulins que sejam eficazes para definir a formulação de uma ou mais massas para produção de componentes de cerâmica estrutural com propriedades físicas, mecânicas e estéticas adequadas após passarem por sinterização convencional e por energia de microondas destacando as vantagens desta última. Além dos requisitos técnicos e de processo, as formulações apresentadas deverão atender às expectativas de preço e de logística de fornecimento. No estudo foram conformados corpos-de-prova por extrusão e prensagem, sinterizados em fornos microondas e convencional, sob ciclos de queima mais rápidos que os atualmente praticados. As matérias-primas foram caracterizadas e analisadas, utilizando as técnicas de fluorescência por raios X (FRX), difração por raios X (DRX), análise térmica diferencial (DTA), análise térmica gravimétrica (DTG), análise granulométrica (AG), microscopia eletrônica de varredura (MEV), absorção d agua (AA), massa especifica aparente (MEA), porosidade aparente (PA), retração linear (RL) e tensão de ruptura e flexão (TRF). Os resultados obtidos indicaram que as propriedades tecnológicas de Absorção de água (AA) e Tensão de Ruptura e flexão (TRF), proposto no trabalho foram adquiridos com sucesso e estão bem além do limite exigido pelas especificações das normas da ABNT NBR 15.270/05 e 15.310/09

Novos monômeros obtidos a partir do metacrilato de glicidila, bisfenol A e 4, 4 isopropilidenodicicloexanol : síntese, caracterização estrutural e propriedades de compósitos para utilização em resinas de restauração dental

Nowadays, composite resins are the direct restorative materials more important in dental clinical performance, due to their versatility and aesthetic excellence. Bis-GMA (2,2-bis[4(2-hydroxy-3-metacryloxypropoxy)phenil]propane) is the base monomer more frequently used in restorative composite resins. However, this monomer presents some disadvantages, such as high viscosity and two aromatic rings in its structure that can promote allergic reactions to the humans. In this work, the main purpose was to synthesize new monomers from glycidyl methacrylate to use in dental restorative materials. Structural characterization of the monomers was carried out through FTIR and NMR 1H, and eight composites were produced from the new monomers, by addition of silane-treated alumino silicate particles (inorganic filler) and a photocuring system (camphorquinone and ethyl 4-dimethylaminebenzoate). The composites were analyzed by environmental scanning electronic microscopy and the water sorption and solubility, compressive strength and elastic modulus were determined. A commercial composite resin [Z100 (3M)] was used to comparison effect. The new composites presented general characteristics similar to the commercial ones; however, they didn t present the properties expected. This behavior was attributed to the lower degree of monomer reaction and to the granulometry and size distribution of the mineral filler in the polymeric matrix

Efeito da velocidade de aquecimento nas propriedades de produtos da cerâmica estrutural

Heating rate is one of the main variables that determine a fire cycle. In industrial processes that use high temperatures, greater fire great can reduce the cost of production and increase productivity. The use of faster and more efficient fire cycles has been little investigated by the structural ceramic industry in Brazil. However, one of the possibilities that aims at modernizing the sector is the use of roller kilns and the inclusion of natural gas as fuel. Thus, the purpose of this study is to investigate the effect of heating rate on the technological properties of structural ceramic products. Clay raw materials from the main ceramic industries in the state of Rio Grande do Norte were characterized. Some of the raw materials characterized were formulated to obtain the best physical and mechanical properties. Next, raw materials and formulations were selected to study the influence of heating rate on the final properties of the ceramic materials. The samples were shaped by pressing and extrusion and submitted to rates of 1 °C/min, 10 °C/min and 20 °C/min, with final temperatures of 850 °C, 950 °C and 1050 °C. Discontinuous cycles with rates of 10 °C/min or 15 °C/min up to 600 °C and a rate of 20 °C/min up to final temperature were also investigated. Technological properties were determined for all the samples and microstructural analysis was carried out under a number of fire conditions. Results indicate that faster and more efficient fire cycles than those currently in practice could be used, limiting only some clay doughs to certain fire conditions. The best results were obtained for the samples submitted to slow cycles up to 600 °C and fast fire sinterization up to 950 °C. This paper presents for the first time the use of a fast fire rate for raw materials and clay formulations and seeks to determine ideal dough and processing conditions for using shorter fire times, thus enabling the use of roller kilns and natural gas in structural ceramic industries

Realismo congnitivo, naturalismo e pragmatismo ético : a estrutura normativa das "formas de vida" segundo Hebermas e Putnam

Pretendo explicitar algumas implicações epistemológicas do debate entre Putnam e Habermas acerca da objetividade dos valores. Inicialmente, gostaria de construir, recorrendo a reflexões em filosofia da linguagem e no neopragmatismo, o horizonte teórico no qual se possa entender de maneira menos unilateral a relação entre naturalismo e a normatividade das “formas de vida” (1). Tais considerações devem funcionar como uma explanação do contexto filosófico em que se desenvolve o debate Habermas/Putnam. Em seguida, gostaria de resumir a posição de Putnam (2). Em terceiro lugar, a partir daquilo que parece ser a direção argumentativa compartilhada, pretendo evidenciar a pertinência do debate para os atuais questionamentos em filosofia prática, delineando os contornos do “pragmatismo ético” (3). Finalmente, procuro mostrar que Habermas escapa à crítica de Putnam aderindo implicitamente à tese da vinculação da moral deontológica a uma orientação axiológica em termos de vulnerabilidade (4). ______________________________________________________________________________ ABSTRACT

A contribuição de técnicas modernas de reabilitação estrutural para autenticidade e integridade de edificações patrimoniais

This work discusses the study of the application of structural reinforcement and rehabilitation using modern techniques for interventions in repair works of historical buildings as well as the verification of the behavior of works that have already undergone different structural intervention techniques, with the objective of obtaining data to allow a comparative analysis of the advantages/disadvantages of techniques adapted in each case, regarding the interferences related the authenticity and integrity of the buildings belong to the constructed patrimony so as to obtain a basis for the theoretical foundation for choosing the best solution to be adopted in the case study which consists in an intervention of structural rehabilitation of the old historic building in the primary school "Augusto Severo"

Hacia las profundidades del campo. Problemas de representación, puesta en escena y realismo en la SHOAH

[ES] El trabajo tiene como objeto contextualizar la evolución de la representación de la Shoah en el cine, así como estudiar las grandes opciones y problemas de puesta en escena y realismo, en base a secuencias y escenas de "Shoah" de Claude Lanzmann y la novedad que propone "El hijo de Saúl" de Lázsló Nemes.

Influência da adição de fibras de celulose (papel kraft) nas características dos blocos de concreto não estrutural

Dissertação (mestrado)—Universidade de Brasília, Faculdade de Tecnologia, Departamento de Engenharia Civil e Ambiental, 2016.

Religión, utopismo y realismo político en el renacimiento

This article examines the opposition between utopism and political realism in the context of Renaissance. First, it analyzes the question about the historical continuity or rupture of Renaissance from the Medieval imaginary. After that, it considers the question of religion in Moore ́s Utopia and Campanella’s City of the Sun and compares them with Machiavelli’s texts. Finally, it thinks about the relationship between Renaissance utopism and religion.

O impacto socioeconômico da implementação do programa jovem aprendiz a partir da inclusão laboral dos jovens aprendizes atendidos pelo Instituto Federal de Brasília - Campus Estrutural

Dissertação apresentada para obtenção do grau de Mestre em Educação Social e Intervenção Comunitária

Validade estrutural e concorrente das escalas de integração social no ensino superior e de suporte relacional extra-universitário

Dissertação de Mestrado apresentada ao Instituto Superior de Psicologia Aplicada para obtenção de grau de Mestre na especialidade de Psicologia Clínica.

Florescimento psicológico e sentido navida: que relações: Validação preliminar da escala MHC-SF

Dissertação de Mestrado apresentada no ISPA – Instituto Universitário para obtenção do grau de Mestre em Psicologia especialidade em Psicologia da Saúde.

O impacto socioeconômico da implementação do programa jovem aprendiz a partir da inclusão laboral dos jovens aprendizes atendidos pelo Instituto Federal de Brasília - Campus Estrutural

Dissertação apresentada para obtenção do grau de Mestre em Educação Social e Intervenção Comunitária