A comparison of road traffic crashes along mountainous and non-mountainous roads in Sabah, Malaysia

Constrained topography and complex road geometry along rural mountainous roads often represent a demanding driving situation. As a result, traffic crashes along mountainous roads are likely to have different characteristics to crashes on roads in flatter areas; however, there is little research on this topic. The objective of this study is to examine the characteristics of road traffic crashes on rural mountainous roads and to compare these with the characteristics of crashes on non-mountainous roads. This paper explores and compares general crash characteristics including crash type, crash severity, roadway geometric features and environmental factors, and road user/vehicle characteristics. Five years of road traffic crash data (2008-2012) for Sabah were obtained from the Malaysian Institute of Road Safety Research. During this period, a total of 25,439 crashes occurred along federal roads in Sabah, of which 4,875 crashes occurred in mountainous areas. Categorical data analysis techniques were used to examine the differences between mountainous and non-mountainous crashes. Results show that the odds ratio of ‘out-of-control’ crashes and the crash involvement due to speeding are respectively about 4.2 times and 2.8 times higher on mountainous than non-mountainous roads. Other factors and crash characteristics that increase the odds of crashes along mountainous roads compared with non-mountainous roads include horizontal curved sections compared with straight sections, single-vehicle crashes compared with multi-vehicle crashes and weekend crashes compared with weekday crashes. This paper identifies some of the basic characteristics of crashes along rural mountainous roads to aid future research on traffic safety along mountainous roads.

The functional liminality of the not-dead-yet students, or, how public schooling became compulsory: A glancing history

This paper redefines the focus for narrating histories of education in the USA through a ‘glancing history’. It highlights the important role played by ‘not-dead-yet students’ who occupied a liminal place on the scale of life in late nineteenth- and early twentieth-century. Traditional histories of education have been more singularly focused on the advent and dynamics of public schooling, ignoring the functionality of such child subjects to public schooling’s existence. This paper argues that public schools as historical objects cannot be understood outside of a broader trinary system of prior institutions that were established for ‘delinquent’ and ‘special’ children. These prior institutions facilitated the formation of ‘the public’ in public schooling less in opposition to ‘the private’ and more in consonance with ‘the human’. The existence of prior institutions enabled the enforcement of compulsory attendance legislation. Compulsory attendance legislation, in place across all existing states by 1918, was concerned more with the conditions for exclusion and exemption than with compelling attendance. Thus, at the most immediate level, this paper historicizes some of the discursive and hence institutional events that linked an array of tutelary complexes by the early 1900s, and which enabled such legislation. This part of the argument extends the notion of institution to consider broader places of confinement and systematicity. It examines the prior practice of reservation and slavery systems, and the efficacy they lent to further institutionalized segregation in the USA. At a second level, the narrative reflects on how such a narration has become possible. It considers how histories of education can currently be rethought and rewritten around the notion of dis/ability, historicizing the formation of dis/ability as identity categories made noticeable in part (and circularly) through the crystallization of a segregated but linked common schooling system. The paper thus provides a counter-memory against dominant economic foundationalist and psychomedical accounts of schooling’s past. It documents both ‘external’ conditions of possibility for public schooling’s emergence and ‘internal’ effects that emerged through the experiences of confinement

The roughness and imaging characterisation of different pharmaceutical surfaces

The surface properties of solid state pharmaceutics are of critical importance. Processing modifies the surfaces and effects surface roughness, which influences the performance of the final dosage form in many different levels. Surface roughness has an effect on, e.g., the properties of powders, tablet compression and tablet coating. The overall goal of this research was to understand the surface structures of pharmaceutical surfaces. In this context the specific purpose was to compare four different analysing techniques (optical microscopy, scanning electron microscopy, laser profilometry and atomic force microscopy) in various pharmaceutical applications where the surfaces have quite different roughness scale. This was done by comparing the image and roughness analysing techniques using powder compacts, coated tablets and crystal surfaces as model surfaces. It was found that optical microscopy was still a very efficient technique, as it yielded information that SEM and AFM imaging are not able to provide. Roughness measurements complemented the image data and gave quantitative information about height differences. AFM roughness data represents the roughness of only a small part of the surface and therefore needs other methods like laser profilometer are needed to provide a larger scale description of the surface. The new developed roughness analysing method visualised surface roughness by giving detailed roughness maps, which showed local variations in surface roughness values. The method was able to provide a picture of the surface heterogeneity and the scale of the roughness. In the coating study, the laser profilometer results showed that the increase in surface roughness was largest during the first 30 minutes of coating when the surface was not yet fully covered with coating. The SEM images and the dispersive X-ray analysis results showed that the surface was fully covered with coating within 15 to 30 minutes. The combination of the different measurement techniques made it possible to follow the change of surface roughness and development of polymer coating. The optical imaging techniques gave a good overview of processes affecting the whole crystal surface, but they lacked the resolution to see small nanometer scale processes. AFM was used to visualize the nanoscale effects of cleaving and reveal the full surface heterogeneity, which underlies the optical imaging. Ethanol washing changed small (nanoscale) structure to some extent, but the effect of ethanol washing on the larger scale was small. Water washing caused total reformation of the surface structure at all levels.

A Design for Testability of Undetectable Crosspoint Faults in Programmable Logic Arrays

In this paper, the validity of'single fault assumption in deriving diagnostic test sets is examined with respect to crosspoint faults in programmable logic arrays (PLA's). The control input procedure developed here can be used to convert PLA's having undetectable crosspoint faults to crosspoint-irredundant PLA's for testing purposes. All crosspoints will be testable in crosspoint-irredundant PLA's. The control inputs are used as extra variables during testing. They are maintained at logic I during normal operation. A useful heuristic for obtaining a near-minimal number of control inputs is suggested. Expressions for calculating bounds on the number of control inputs have also been obtained.

Evaluation of Inoculated Lablab Silage for Growing Dairy Heifers

A summer grown forage legume crop – Lablab (Lablab purpureus) harvested in autumn, was ensiled as plastic wrapped, large round bales. Of the 30 bales produced, 13 were inoculated with a bacterial inoculant containing Lactobacillus plantarum and Enterococcus faecium. Inoculant was premixed at 30 g/litre water, cultured overnight (18 hours) then sprayed onto cut forage during the baling and wrapping procedure at 1 litre per tonne of silage. A replicated feeding experiment was conducted in July - August 1998 (5 weeks), using 24 eight month old Holstein Friesian heifers group fed non-inoculated or inoculated silage to appetite plus 2 kg rolled sorghum grain/heifer.day. Chemical composition and nutritive value of well preserved bales of control and inoculated silages were similar (P>0.05) with 50% DM and 26 g N and 6.8 MJ ME per kg DM. Lactic acid and acetic acid concentrations were 11.4 v. 11.4 and 4.90 v. 3.75 g/kg DM for control and inoculated silages respectively (P>0.05). Heifers preferentially selected leaf from the silage offered and maintained liveweight gains of 0.70 and 0.61 kg/day respectively (P>0.05) during the silage feeding period. High DM and low WSC content of the parent forage may have reduced the opportunity for the bacterial inoculant to have effect. Animal production for a consuming world : proceedings of 9th Congress of the Asian-Australasian Association of Animal Production Societies [AAAP] and 23rd Biennial Conference of the Australian Society of Animal Production [ASAP] and 17th Annual Symposium of the University of Sydney, Dairy Research Foundation, [DRF]. 2-7 July 2000, Sydney, Australia.

Using simulation techniques to investigate methods to determine resistance of helminths to anthelmintic treatment

The widespread and increasing resistance of internal parasites to anthelmintic control is a serious problem for the Australian sheep and wool industry. As part of control programmes, laboratories use the Faecal Egg Count Reduction Test (FECRT) to determine resistance to anthelmintics. It is important to have confidence in the measure of resistance, not only for the producer planning a drenching programme but also for companies investigating the efficacy of their products. The determination of resistance and corresponding confidence limits as given in anthelmintic efficacy guidelines of the Standing Committee on Agriculture (SCA) is based on a number of assumptions. This study evaluated the appropriateness of these assumptions for typical data and compared the effectiveness of the standard FECRT procedure with the effectiveness of alternative procedures. Several sets of historical experimental data from sheep and goats were analysed to determine that a negative binomial distribution was a more appropriate distribution to describe pre-treatment helminth egg counts in faeces than a normal distribution. Simulated egg counts for control animals were generated stochastically from negative binomial distributions and those for treated animals from negative binomial and binomial distributions. Three methods for determining resistance when percent reduction is based on arithmetic means were applied. The first was that advocated in the SCA guidelines, the second similar to the first but basing the variance estimates on negative binomial distributions, and the third using Wadley’s method with the distribution of the response variate assumed negative binomial and a logit link transformation. These were also compared with a fourth method recommended by the International Co-operation on Harmonisation of Technical Requirements for Registration of Veterinary Medicinal Products (VICH) programme, in which percent reduction is based on the geometric means. A wide selection of parameters was investigated and for each set 1000 simulations run. Percent reduction and confidence limits were then calculated for the methods, together with the number of times in each set of 1000 simulations the theoretical percent reduction fell within the estimated confidence limits and the number of times resistance would have been said to occur. These simulations provide the basis for setting conditions under which the methods could be recommended. The authors show that given the distribution of helminth egg counts found in Queensland flocks, the method based on arithmetic not geometric means should be used and suggest that resistance be redefined as occurring when the upper level of percent reduction is less than 95%. At least ten animals per group are required in most circumstances, though even 20 may be insufficient where effectiveness of the product is close to the cut off point for defining resistance.

Evaluation of the Australian branched broomrape (Orobanche ramosa) eradication program

Because weed eradication programs commonly take 10 or more years to complete, there is a need to evaluate progress toward the eradication objective. We present a simple model, based on information that is readily obtainable, that assesses conformity to the delimitation and extirpation criteria for eradication. It is applied to the program currently targeting the annual parasitic weed, branched broomrape, in South Australia. The model consists of delimitation and extirpation (E) measures plotted against each other to form an 'eradograph.' Deviations from the 'ideal' eradograph plot can inform tactical responses, e.g., increases in survey and/or control effort. Infestations progress from the active phase to the monitoring phase when no plants have been detected for at least 12 mo. They revert to the active phase upon further detection of plants. We summarize this process for the invasion as a whole in a state-and-transition model. Using this model we demonstrate that the invasion is unlikely to be delimited unless the amount of newly detected infested area decreases, on average, by at least 50% per annum. As a result of control activities implemented, on average approximately 70% (range, 44 to 86%) of active infestations progressed to the monitoring phase in the year following their detection. Simulations suggest that increasing this rate of transition will not increase E to a significant extent. The rate of reversion of infestations from the monitoring phase to the active phase decreased logarithmically with time since last detection, but it is likely that lower rates of reversion would accelerate the trend toward extirpation. Program performance with respect to the delimitation criterion has been variable; performance with respect to the extirpation criterion would be improved considerably by the development and application of cost-effective methods for eliminating branched broomrape soil seed populations.

Time dependence of effective slip on textured hydrophobic surfaces

In this paper, we present results on water flow past randomly textured hydrophobic surfaces with relatively large surface features of the order of 50 µm. Direct shear stress measurements are made on these surfaces in a channel configuration. The measurements indicate that the flow rates required to maintain a shear stress value vary substantially with water immersion time. At small times after filling the channel with water, the flow rates are up to 30% higher compared with the reference hydrophilic surface. With time, the flow rate gradually decreases and in a few hours reaches a value that is nearly the same as the hydrophilic case. Calculations of the effective slip lengths indicate that it varies from about 50 µm at small times to nearly zero or “no slip” after a few hours. Large effective slip lengths on such hydrophobic surfaces are known to be caused by trapped air pockets in the crevices of the surface. In order to understand the time dependent effective slip length, direct visualization of trapped air pockets is made in stationary water using the principle of total internal reflection of light at the water-air interface of the air pockets. These visualizations indicate that the number of bright spots corresponding to the air pockets decreases with time. This type of gradual disappearance of the trapped air pockets is possibly the reason for the decrease in effective slip length with time in the flow experiments. From the practical point of usage of such surfaces to reduce pressure drop, say, in microchannels, this time scale of the order of 1 h for the reduction in slip length would be very crucial. It would ultimately decide the time over which the surface can usefully provide pressure drop reductions. ©2009 American Institute of Physics

Remote sensing of nitrogen and water stress in wheat

Nitrogen (N) is the largest agricultural input in many Australian cropping systems and applying the right amount of N in the right place at the right physiological stage is a significant challenge for wheat growers. Optimizing N uptake could reduce input costs and minimize potential off-site movement. Since N uptake is dependent on soil and plant water status, ideally, N should be applied only to areas within paddocks with sufficient plant available water. To quantify N and water stress, spectral and thermal crop stress detection methods were explored using hyperspectral, multispectral and thermal remote sensing data collected at a research field site in Victoria, Australia. Wheat was grown over two seasons with two levels of water inputs (rainfall/irrigation) and either four levels (in 2004; 0, 17, 39 and 163 kg/ha) or two levels (in 2005; 0 and 39 kg/ha N) of nitrogen. The Canopy Chlorophyll Content Index (CCCI) and modified Spectral Ratio planar index (mSRpi), two indices designed to measure canopy-level N, were calculated from canopy-level hyperspectral data in 2005. They accounted for 76% and 74% of the variability of crop N status, respectively, just prior to stem elongation (Zadoks 24). The Normalised Difference Red Edge (NDRE) index and CCCI, calculated from airborne multispectral imagery, accounted for 41% and 37% of variability in crop N status, respectively. Greater scatter in the airborne data was attributable to the difference in scale of the ground and aerial measurements (i.e., small area plant samples against whole-plot means from imagery). Nevertheless, the analysis demonstrated that canopy-level theory can be transferred to airborne data, which could ultimately be of more use to growers. Thermal imagery showed that mean plot temperatures of rainfed treatments were 2.7 °C warmer than irrigated treatments (P < 0.001) at full cover. For partially vegetated fields, the two-Dimensional Crop Water Stress Index (2D CWSI) was calculated using the Vegetation Index-Temperature (VIT) trapezoid method to reduce the contribution of soil background to image temperature. Results showed rainfed plots were consistently more stressed than irrigated plots. Future work is needed to improve the ability of the CCCI and VIT methods to detect N and water stress and apply both indices simultaneously at the paddock scale to test whether N can be targeted based on water status. Use of these technologies has significant potential for maximising the spatial and temporal efficiency of N applications for wheat growers. ‘Ground–breaking Stuff’- Proceedings of the 13th Australian Society of Agronomy Conference, 10-14 September 2006, Perth, Western Australia.

The effect of habitat and environmental history on otolith chemistry of barramundi Lates calcarifer in estuarine populations of a regulated tropical river

We examine the microchemistry of otoliths of cohorts of a fished shed population of the large catadromous fish, barramundi Lates calcarifer from the estuary of a large tropical river. Barramundi from the estuary of the large, heavily regulated Fitzroy River, north eastern Australia were analysed by making transects of 87Sr/86Sr isotope and trace metal/Ca ratios from the core to the outer edge. Firstly, we examined the Sr/Ca, Ba/Ca, Mg/Ca and Mn/Ca and 87Sr/86Sr isotope ratios in otoliths of barramundi tagged in either freshwater or estuarine habitats that were caught by the commercial fishery in the estuary. We used 87Sr/86Sr isotope ratios to identify periods of freshwater residency and assess whether trace metal/Ca ratios varied between habitats. Only Sr/Ca consistently varied between known periods of estuarine or freshwater residency. The relationships between trace metal/Ca and river flow, salinity, temperature were examined in fish tagged and recaptured in the estuary. We found weak and inconsistent patterns in relationships between these variables in the majority of fish. These results suggest that both individual movement history within the estuary and the scale of environmental monitoring were reducing our ability to detect any patterns. Finally, we examined fish in the estuary from two dominant age cohorts (4 and 7 yr old) before and after a large flood in 2003 to ascertain if the flood had enabled fish from freshwater habitats to migrate to the estuary. There was no difference in the proportion of fish in the estuary that had accessed freshwater after the flood. Instead, we found that larger individuals with each age cohort were more likely to have spent a period in freshwater. This highlights the need to maintain freshwater flows in rivers. About half the fish examined had accessed freshwater habitats before capture. Of these, all had spent at least their first two months in marine salinity waters before entering freshwater and some did not enter freshwater until four years of age. This contrasts with the results of several previous studies in other parts of the range that found that access to freshwater swamps by larval barramundi was important for enhanced population productivity and recruitment.

Expert Identity in Development of Core-Task-Oriented Working Practices for Mastering Demanding Situations

The point of departure in this dissertation was the practical safety problem of unanticipated, unfamiliar events and unexpected changes in the environment, the demanding situations which the operators should take care of in the complex socio-technical systems. The aim of this thesis was to increase the understanding of demanding situations and of the resources for coping with these situations by presenting a new construct, a conceptual model called Expert Identity (ExId) as a way to open up new solutions to the problem of demanding situations and by testing the model in empirical studies on operator work. The premises of the Core-Task Analysis (CTA) framework were adopted as a starting point: core-task oriented working practices promote the system efficiency (incl. safety, productivity and well-being targets) and that should be supported. The negative effects of stress were summarised and the possible countermeasures related to the operators' personal resources such as experience, expertise, sense of control, conceptions of work and self etc. were considered. ExId was proposed as a way to bring emotional-energetic depth into the work analysis and to supplement CTA-based practical methods to discover development challenges and to contribute to the development of complex socio-technical systems. The potential of ExId to promote understanding of operator work was demonstrated in the context of the six empirical studies on operator work. Each of these studies had its own practical objectives within the corresponding quite broad focuses of the studies. The concluding research questions were: 1) Are the assumptions made in ExId on the basis of the different theories and previous studies supported by the empirical findings? 2) Does the ExId construct promote understanding of the operator work in empirical studies? 3) What are the strengths and weaknesses of the ExId construct? The layers and the assumptions of the development of expert identity appeared to gain evidence. The new conceptual model worked as a part of an analysis of different kinds of data, as a part of different methods used for different purposes, in different work contexts. The results showed that the operators had problems in taking care of the core task resulting from the discrepancy between the demands and resources (either personal or external). The changes of work, the difficulties in reaching the real content of work in the organisation and the limits of the practical means of support had complicated the problem and limited the possibilities of the development actions within the case organisations. Personal resources seemed to be sensitive to the changes, adaptation is taking place, but not deeply or quickly enough. Furthermore, the results showed several characteristics of the studied contexts that complicated the operators' possibilities to grow into or with the demands and to develop practices, expertise and expert identity matching the core task. They were: discontinuation of the work demands, discrepancy between conceptions of work held in the other parts of organisation, visions and the reality faced by the operators, emphasis on the individual efforts and situational solutions. The potential of ExId to open up new paths to solving the problem of the demanding situations and its ability to enable studies on practices in the field was considered in the discussion. The results were interpreted as promising enough to encourage the conduction of further studies on ExId. This dissertation proposes especially contribution to supporting the workers in recognising the changing demands and their possibilities for growing with them when aiming to support human performance in complex socio-technical systems, both in designing the systems and solving the existing problems.

Understanding the determinants of Australian hospital nurses' hand hygiene decisions following the implementation of a national hand hygiene initiative

Hand hygiene is the primary measure in hospitals to reduce the spread of infections, with nurses experiencing the greatest frequency of patient contact. The ‘5 critical moments’ of hand hygiene initiative has been implemented in hospitals across Australia, accompanied by awareness-raising, staff training and auditing. The aim of this study was to understand the determinants of nurses’ hand hygiene decisions, using an extension of a common health decision-making model, the theory of planned behaviour (TPB), to inform future health education strategies to increase compliance. Nurses from 50 Australian hospitals (n = 2378) completed standard TPB measures (attitude, subjective norm, perceived behavioural control [PBC], intention) and the extended variables of group norm, risk perceptions (susceptibility, severity) and knowledge (subjective, objective) at Time 1, while a sub-sample (n = 797) reported their hand hygiene behaviour 2 weeks later. Regression analyses identified subjective norm, PBC, group norm, subjective knowledge and risk susceptibility as the significant predictors of nurses’ hand hygiene intentions, with intention and PBC predicting their compliance behaviour. Rather than targeting attitudes which are already very favourable among nurses, health education strategies should focus on normative influences and perceptions of control and risk in efforts to encourage hand hygiene adherence.

Cassowary dispersal of the invasive pond apple in a tropical rainforest: the contribution of subordinate dispersal modes in invasion.

Dispersal is a significant determinant of the pattern and process of invasions; however, weed dispersal distances are rarely described and descriptions of dispersal kernels are completely lacking for vertebrate-dispersed weeds. Here, we describe dispersal kernels generated by a native disperser, the endangered southern cassowary (Casuarius casuarius, L.) for an invasive, tropical rainforest plant, pond apple (Annona glabra, L.). Pond apple is primarily water-dispersed and is managed as such. We consider whether cassowary dispersal, as a numerically subordinate dispersal mode, provides an additional dispersal service that may modify the invasion process. In infested areas, pond apple seed was common in cassowary dung. Gut passage had no effect on the probability of single seed germination but deposition in clumps or as whole fruits reduced the probability of germination below that of single seeds. Gut passage times ranged from 65 to 1675 min. Combined with cassowary movement data, this resulted in estimated dispersal distances of 12.5-5212 m, with a median distance of 387 m (quartile range 112-787 m). Native frugivores can be effective dispersers of weeds in rainforest and even terrestrial dispersers can provide long-distance dispersal. Importantly, though pond apple might be expected to be almost entirely dispersed downstream and along the margins of aquatic and marine habitats, cassowaries provide dispersal upstream and between drainages, leading to novel dispersal outcomes. Even through the provision of small quantities of novel dispersal outcomes, subordinate dispersal modes can play a significant role in determining invasion pattern and influence the ultimate success of control programs by providing dispersal to locations unattainable via the primary mode.

Effect of foliar herbicides on the germination and viability of Siam weed (Chromolaena odorata) seeds located on plants at the time of application.

This paper reports a field study undertaken to determine if the foliar application of herbicides fluroxypyr (150 mL 100 L-1 a.i.) and metsulfuron-methyl (12 g 100 L-1 a.i.) were capable of reducing the germination and viability of Chromolaena odorata (L.) R.M.King & H.Rob. (Siam weed) seeds at three different stages of maturity. After foliar application of fluroxypyr germination of mature seeds was reduced by 88% and intermediate and immature seeds were reduced by 100%, compared to the control. Fluroxypyr also reduced the viability of mature, intermediate and immature seeds by 79, 89 and 67% respectively, compared to the control. Metsulfuron-methyl reduced germination of intermediate and immature seeds by 53 and 99% respectively compared to the control. Viability was also reduced by 74 and 96% respectively, compared to the control. Mature seeds were not affected by metsulfuron-methyl as germination and viability increased by 2% and 1% respectively, as compared to the control. These results show that these herbicides are capable of reducing the amount of viable seed entering the seed bank. However depending on the treatment and stage of seed development a percentage of seeds on the plants will remain viable and contribute to the seed bank. This information is of value to Siam weed eradication teams as plants are most easily located and subsequently treated at the time of flowering. Knowledge of the impact of control methods on seeds at various stages of development will help determine the most suitable chemical control option for a given situation.

Factors affecting localized abundance and distribution of lesser mealworm in earth-floor broiler houses in subtropical Australia.

Factors that influence the localized abundance and distribution of lesser mealworm, Alphitobius diaperinus (Panzer), in litter of two compacted earth-floor broiler houses in subtropical Australia were studied using various experimental manipulations. Numbers of lesser mealworms substantially increased inside caged areas and under uncaged empty feed pans placed in open areas of the houses. These populations were found to be localized and independent of chicken-feed, manure, and high beetle populations that normally occur under existing feed pans. Substantial horizontal movement of larvae to under feed pans was recorded. Placing metal barriers around these pans significantly restricted this movement. In almost all treatments, lesser mealworms typically peaked in numbers during the middle of the flock time. This temporal pattern of abundance also was observed under pans within barriers, where relatively low insect numbers occurred, but it was not observed in uncaged open areas (where chickens had complete access). It is likely that larvae do not establish in open areas, but fluctuate in numbers as they either move to refuges away from chickens or suffer high rates of mortality. In these refuges, larvae peak in numbers and then leave the litter environment to pupate in the earth floor before the end of the flock time. This behavior might be exploited for management of lesser mealworm by targeting applications of control agents.