928 resultados para Mortars of replacement
Resumo:
A ready-mixed and several laboratory formulated mortars were produced and tested in fresh state and after hardening, simulating a masonry plaster for indoor application. All the mortars used a clayish earth from the same region and different compositions of aggregates, eventually including fibres and a phase change material. All the formulated mortars were composed by 1:3 volumetric proportions of earth and aggregate. Tests were developed for consistency, fresh bulk density, thermal conductivity, capillary absorption and drying, water vapour permeability and sorption-desorption. The use of PCM changed drastically the workability of the mortars and increased their capillary absorption. The use of fibres and variations on particle size distribution of the mixtures of sand that were used had no significant influence on tested properties. But particularly the good workability of these mortars and the high capacity of sorption and desorption was highlighted. With this capacity plasters made with these mortars are able to adsorb water vapour from indoor atmosphere when high levels of relative humidity exist and release water vapour when the indoor atmosphere became too dry. This fact makes them able to contribute passively for a healthier indoor environment. The technical, ecological and environmental advantages of the application of plasters with this type of mortars are emphasized, with the aim of contributing for an increased use for new or existent housing.
Resumo:
Due to their high adsorption capacity of water vapor, earthen plasters can act as a moisture buffer, contributing to balance the relative humidity of the indoor environment of buildings. As a consequence of this capacity earthen plasters may also contribute to the perception of thermal comfort, since a high relative humidity increases the thermal conductivity of air and restricts skin evaporation, increasing the discomfort associated with the perception of heat or cold. Simultaneously, earthen plasters may also contribute to the indoor air quality. In one hand, by mitigating health problems of the respiratory system associated with indoor environment with high relative humidity, in which increases the risk of development of microorganisms usually responsible for infections, allergies or asthma. In the other hand, by mitigating the probability of inflammation of the respiratory system airways associated to exceedingly dry indoor environments. Therefore it also becomes expectable that earthen plasters may contribute for reducing the needs for air conditioning and mechanical ventilation in buildings and, thereby, also allowing the reduction of the associated energy consumption. The «Barrocal» region, located in the sedimentary basin of Algarve, South Portugal, presents geomorphological characteristics that promote the occurrence of soils with a clay mineralogy dominated by illite, which is a clay mineral characterized by a high adsorption capacity of water vapor and low expansibility. This fact turns expectable that these soils have a high potential for interior plastering. In order to evaluate this potential four mortars were formulated with an increasing content of clayey soil extracted from a selected clay quarry from «Barrocal» region. The results from the preliminary characterization campaign confirmed the reduced linear shrinkage of these mortars, as well as their high adsorption-desorption capacity, that is positively correlated with the content of clayey soil present in mortar formulation. However, the mechanical tests showed that the mechanical resistance of these mortars should be improved, for instance through the addition of natural fibers for reinforcement, which will be investigated in future research. This research contributed to increase certainty regarding the potential of clayey soils of the «Barrocal» sub-region of Algarve to produce mortars suitable for eco-efficient interior plastering.
Resumo:
Historical renders are exposed to several degradation processes that can lead to a wide range of anomalies,such as scaling, detachments, and pulverization. Among the common anomalies, the loss of cohesion and of adhesion are usually identified as the most difficult to repair; these anomalies still need to be deeply studied to design compatible, durable, and sustainable conservation treatments. The restitution of render cohesion can be achieved using consolidating products. Nevertheless, repair treatments could induce aesthetic alterations, and, therefore, are usually followed by chromatic reintegration. This work aims to study the effectiveness of mineral products as consolidants for lime-based mortars and simultaneously as chromatic treatments for pigmented renders. The studied consolidating products are prepared by mixing air lime,metakaolin, water, and mineral pigments. The idea of these consolidating and coloring products rises from a traditional lime-based technique, the limewash, widely diffused in southern Europe and in the Mediterranean area. Consolidating products were applied and tested on lime-based mortar specimens with a low binder–aggregate ratio and therefore with reduced cohesion. A physico-mechanical, microstructural, and mineralogical characterization was performed on untreated and treated specimens, in order to evaluate the efficacy and durability of the treatments. Accelerated aging tests were also performed to assess consolidant durability, when subjected to aggressive conditions. Results showed that the consolidants tested are compatible, effective, and possess good durability.
Resumo:
Epistemology in philosophy of mind is a difficult endeavor. Those who believe that our phenomenal life is different from other domains suggest that self-knowledge about phenomenal properties is certain and therefore privileged. Usually, this so called privileged access is explained by the idea that we have direct access to our phenomenal life. This means, in contrast to perceptual knowledge, self-knowledge is non-inferential. It is widely believed that, this kind of directness involves two different senses: an epistemic sense and a metaphysical sense. Proponents of this view often claim that this is due to the fact that we are acquainted with our current experiences. The acquaintance thesis, therefore, is the backbone in justifying privileged access. Unfortunately the whole approach has a profound flaw. For the thesis to work, acquaintance has to be a genuine explanation. Since it is usually assumed that any knowledge relation between judgments and the corresponding objects are merely causal and contingent (e.g. in perception), the proponent of the privileged access view needs to show that acquaintance can do the job. In this thesis, however, I claim that the latter cannot be done. Based on considerations introduced by Levine, I conclude that this approach involves either the introduction of ontologically independent properties or a rather obscure knowledge relation. A proper explanation, however, cannot employ either of the two options. The acquaintance thesis is, therefore, bound to fail. Since the privileged access intuition seems to be vital to epistemology within the philosophy of mind, I will explore alternative justifications. After discussing a number of options, I will focus on the so called revelation thesis. This approach states that by simply having an experience with phenomenal properties, one is in the position to know the essence of those phenomenal properties. I will argue that, after finding a solution for the controversial essence claim, this thesis is a successful replacement explanation which maintains all the virtues of the acquaintance account without necessarily introducing ontologically independent properties or an obscure knowledge relation. The overall solution consists in qualifying the essence claim in the relevant sense, leaving us with an appropriate ontology for phenomenal properties. On the one hand, this avoids employing mysterious independent properties, since this ontological view is physicalist in nature. On the other hand, this approach has the right kind of structure to explain privileged self-knowledge of our phenomenal life. My final conclusion consists in the claim that the privileged access intuition is in fact veridical. It cannot, however, be justified by the popular acquaintance approach, but rather, is explainable by the controversial revelation thesis.
Resumo:
This thesis focused on the study and treatment of a 19th century female portrait in oil from ECOMUSEU Municipal do Seixal, Portugal. The portrait, which depicts Isabel Maria Lourenço Affonso was in poor condition and a large strip of paint and canvas was missing (approximately 9cm by 66cm, almost 11% of the total surface area). The portrait is a companion piece to a male portrait (the relationship was established as part of this study), therefore a technical study of both paintings was considered essential to support the choices made during the treatment. The project involved three main areas: - The study of the history, condition, materials and techniques of both paintings. This allowed their comparison and understanding of their relationship; - The treatment of Isabel Maria Lourenço Affonso. The choices made and problems encountered are described. - The production of a replacement for the missing strip of paint and canvas. The practical solution developed to overcome such an unusual challenge is described along with the creative and flexible thinking required. Because not all traditional infill materials cope well on a mechanical level with thin layers over a very large surface (many are too brittle), strict criteria had to be employed to choose the appropriate material. The primary goal was to find a fill which would remain flexible and be capable of accepting surface texture, such that there would be a good visual match with the painting. Analysis and testing was carried out to evaluate the physical properties of the fill material chosen, BEVA® Gesso-P. The successful creation of the replacement strip has resulted in two publications and one presentation: Publication pending in The Picture Restorer, Leslie Carlyle, Raquel Marques, Isabel Pombo Cardoso and Sara Babo, “Creating a Textured Replacement Strip for the Missing Lower Portion of an Oil Portrait: Problem Solving and Practical Solutions”. Abstract accepted for presentation and publication, International Meeting on Retouching of Cultural Heritage (2RECH), Raquel Marques, Leslie Carlyle and Isabel Pombo Cardoso, “Textured Replacement Strip for a Missing Portion of a Portrait: Problem Solving and Practical Solutions”.
Resumo:
INTRODUCTION: HTLV-1/2 screening among blood donors commonly utilizes an enzyme-linked immunosorbent assay (EIA), followed by a confirmatory method such as Western blot (WB) if the EIA is positive. However, this algorithm yields a high rate of inconclusive results, and is expensive. METHODS: Two qualitative real-time PCR assays were developed to detect HTLV-1 and 2, and a total of 318 samples were tested (152 blood donors, 108 asymptomatic carriers, 26 HAM/TSP patients and 30 seronegative individuals). RESULTS: The sensitivity and specificity of PCR in comparison with WB results were 99.4% and 98.5%, respectively. PCR tests were more efficient for identifying the virus type, detecting HTLV-2 infection and defining inconclusive cases. CONCLUSIONS: Because real-time PCR is sensitive and practical and costs much less than WB, this technique can be used as a confirmatory test for HTLV in blood banks, as a replacement for WB.
Resumo:
Clayish earth-based mortars are been recognized, all over the world, as eco-efficient products for plastering. Apart from being a product with low embodied energy when compared to other types of plasters, their application on the interior surface of walls may give a strong contribution for the health and comfort of inhabitants. As part of an ongoing research regarding earth-based plasters this work assesses the influence of the addition of two types of natural fibres – oat straw and typha fiber-wool – on the characteristics of plastering mortars made with a clayish earth. Mechanical and physical characteristics were tested, showing that addition of these fibers contribute to decrease linear drying shrinkage and thermal conductivity, as well as promoting the adhesion strength of plaster to the substrate. The improvement of mechanical resistance reveal to be dependent on the type of fiber added while the hygroscopic capacity of the plaster is maintained regardless of the fiber additions.
Resumo:
The use of wastes and industrial by-products as building materials is an important issue in order to decrease costs with waste management and the embodied energy of building products. Scrap tire rubber has been studied as aggregate for cementitious materials. Natural hydraulic limes are natural binders with particular characteristics of both air and hydraulic binders. Their specifications became stricter with the last version of EN 459-1:2010. In this study scrap tire rubber was used as additional aggregate of mortars, based on NHL3.5 and natural sand. Different particle size fractions and proportions of scrap tire rubber were used: a mix obtained almost directly from industry (only after sieving for preparation of particle sizes similar to mortar aggregate) and separated fine, medium and coarse fractions; 0%, 18%, 36% and 54% weight of binder, corresponding to 2.5%, 5% and 7.5% weight of sand. The influence of the rubbers´ additions on the mortars´ fresh state, mechanical and physical performance is presented, namely by flow table consistency, water retention, fresh bulk density, dynamic elasticity modulus, flexural and compressive strength, open porosity and bulk density, capillary absorption, drying and thermal conductivity. The use of the rubber mix coming from the waste tire industry seems advantageous and may open possibilities for use as raw material by the mortars industry.
Resumo:
Earthen plastering mortars are becoming recognized as highly eco-efficient. The assessment of their technical properties needs to be standardized but only the German standard DIN 18947 exists for the moment. An extended experimental campaign was developed in order to assess multiple properties of a ready-mixed earth plastering mortar and also to increase scientific knowledge of the influence of test procedures on those properties. The experimental campaign showed that some aspects related to the equipment, type of samples and sample preparation can be very important, while others seemed to have less influence on the results and the classification of mortars. It also showed that some complementary tests can easily be performed and considered together with the standardized ones, while others may need to be improved. The plaster satisfied the requirements of the existing German standard but, most importantly, it seemed adequate for application as rehabilitation plaster on historic and modern masonry buildings. Apart from their aesthetic aspect, the contribution of earthen plasters to eco-efficiency and particularly to hygrometric indoor comfort should be highlighted.
Resumo:
Worldwide aging of the human population has promoted an increase in the incidence of neoplasia, including hematological cancers, which render patients particularly vulnerable to invasive fungal infections. For this reason, air filtration in hemato-oncology units has been recommended. However, scarce literature has assessed the impact of microbiological air quality on the occurrence of fungal infections in this population. We performed an integrative review of studies in the MEDLINE database that were published between January 1980 and October 2012, using the following combinations of keywords: air × quality × HEPA, air × quality × hematology, and airborne fungal infections. The search yielded only 13 articles, suggesting that high-efficiency filtering of the ambient air in hemato-oncology units can prevent the incidence of invasive fungal infections. However, no randomized clinical trial was found to confirm this suggestion. Currently, there is no consensus about the maximum allowable count of fungi in the air, which complicates filtration monitoring, including filter maintenance and replacement, and needs to be addressed in future studies.
Resumo:
Mega-organs, primarily in the digestive tract, are well known to occur in chronic Chagas disease. Acute experimental infection with Trypanosoma cruzi results in parasitism of a wide range of cells, tissues, and organs, including the urinary bladder. Infection of BALB/c mice with 100,000 bloodstream forms of the Y strain of T. cruzi induced acute infection with intense parasitism of all layers of the urinary bladder. Parasites were found in the mucosa, lamina propria, muscular, adventitial connective, and fat tissue. Desquamate epithelial cells with amastigotes in the bladder lumen were also found. After 60 days of infection, mice inoculated with 50 bloodstream forms developed dilated, thin-walled bladders that had inflammatory infiltrates and foci of fibrosis replacing areas of damaged muscular layer. These lesions result from direct damage to the muscle fibers by the T. cruzi, leading to myosites, muscle damage, and scarring. Direct damage of paraganglia cells secondary to parasitism, leading to dilatation, damage of muscle fibers, and scarring with replacement of muscular tissue with connective tissue, should also be considered as a cause of functional disturbance of the urinary bladder.
Resumo:
Scarcity of fuels, changes in environmental policy and in society increased the interest in generating electric energy from renewable energy sources (RES) for a sustainable energy supply in the future. The main problem of RES as solar and wind energy, which represent a main pillar of this transition, is that they cannot supply constant power output. This results inter alia in an increased demand of backup technologies as batteries to assure electricity system safety. The diffusion of energy storage technologies is highly dependent on the energy system and transport transition pathways which might lead to a replacement or reconfiguration of embedded socio-technical practices and regimes (by creating new standards or dominant designs, changing regulations, infrastructure and user patterns). The success of this technology is dependent on hardly predictable future technical advances, actor preferences, development of competing technologies and designs, diverging interests of actors, future cost efficiencies, environmental performance, the evolution of market demand and design and evolution of our society.
Resumo:
Clayish earth-based mortars can be considered eco-efficient products for indoor plastering since they can contribute to improve important aspects of building performance and sustainability. Apart from being products with low embodied energy when compared to other types of mortars used for interior plastering, mainly due to the use raw clay as natural binder, earth-based plasters may give a significant contribution for health and comfort of inhabitants. Due to high hygroscopicity of clay minerals, earth-based mortars present a high adsorption and desorption capacity, particularly when compared to other type of mortars for interior plastering. This capacity allows earth-based plasters to act as a moisture buffer, balancing the relative humidity of the indoor environment and, simultaneously, acting as a passive removal material, improving air quality. Therefore, earth-based plasters may also passively promote the energy efficiency of buildings, since they may contribute to decreasing the needs of mechanical ventilation and air conditioning. This study is part of an ongoing research regarding earth-based plasters and focuses on mortars specifically formulated with soils extracted from Portuguese ‘Barrocal’ region, in Algarve sedimentary basin. This region presents high potential for interior plastering due to regional geomorphology, that promote the occurrence of illitic soils characterized by a high adsorption capacity and low expansibility. More specifically, this study aims to assess how clayish earth and sand ratio of mortars formulation can influence the physical and mechanical properties of plasters. For this assessment four mortars were formulated with different volumetric proportions of clayish earth and siliceous sand. The results from the physical and mechanical characterization confirmed the significantly low linear shrinkage of all the four mortars, as well as their extraordinary adsorption-desorption capacity. These results presented a positive correlation with mortars´ clayish earth content and are consistent with the mineralogical analysis, that confirmed illite as the prevalent clay mineral in the clayish earth used for this study. Regarding mechanical resistance, although the promising results of the adhesion test, the flexural and compressive strength results suggest that the mechanical resistance of these mortars should be slightly improved. Considering the present results the mortars mechanical resistance improvement may be achieved through the formulation of mortars with higher clayish earth content, or alternatively, through the addition of natural fibers to mortars formulation, very common in this type of mortars. Both those options will be investigated in future research.
Resumo:
Due to the prospective partial replacement of fossil fuels by biodiesel, its production has continuously grown in the last decade. The increase in global biodiesel production demands the development of sustainable applications of its main by-product, crude glycerol. In this thesis the feasibility of producing polyhydroxyalkanoates (PHA) by a mixed microbial community using crude glycerol as feedstock was investigated. Several incubation conditions were studied in order to maximize PHA production. The microbial population selected under aerobic dynamic feeding conditions had the ability to consume both major carbon fractions present in the crude, glycerol and methanol. Two biopolymers were stored, poly-3-hydroxybutyrate (PHB) and glucose biopolymer (GB), apparently using glycerol as the only carbon source for their production. The microbial enrichment obtained was able to accumulate up to 47% PHB of cell dry weight with a productivity of 0.24 g HA/L d. The overall PHA yield on total substrate consumed (0.32 g COD HB/g COD crude glycerol) was in the middle range of those reported in literature (0.08–0.58 g COD PHA/g COD real waste). The increase of temperature from 23ºC to 30ºC favored the culture fraction that accumulates glucose biopolymer with a maximum accumulation value of 25% of cell dry weight, which is an interesting value but not the main goal of this thesis. The fact that crude glycerol can be used to produce PHA without any pre-treatment step, makes the overall production process economically more competitive, reducing polymer final cost. This was the first study that demonstrates the valorization of the glycerol fraction present in the crude glycerol into PHA using an aerobic mixed microbial consortium.
Resumo:
PURPOSE: The dura mater bioprosthesis was developed in the Department of Cardiopneumology of the Hospital das Clínicas of the University of São Paulo Medical School in 1971. Here, we present the clinical results of the dura mater bioprosthesis over 30 years of follow-up. METHODS: We studied 70 consecutive patients who underwent mitral or tricuspid valve replacement with a dura mater bioprosthesis between January 1971 and August 1972. RESULTS: The early mortality was 10% (7 patients). The follow-up was 87% complete (9 patients were lost to follow-up). Two patients were alive and asymptomatic 30 years after valve replacement; 33 patients underwent reoperations due to valve dysfunction, and 19 died during the follow-up period. At 30 years, the actuarial survival was 49.2 ± 8.6%; freedom from rupture, 27.0 ± 10.2%; freedom from calcification, 78.8 ± 8.6%; and freedom from reoperation, 18.8 ± 7.5%. CONCLUSIONS: The dura mater bioprosthesis played an important role in the treatment of patients with mitral and tricuspid valve disease. The low rate of thromboembolism and the long period of follow-up without evidence of valve dysfunction, which occurred for several of our patients, are important characteristics of these bioprosthesis.