Obtenção e caracterização de um compósito de matriz polimérica com carga de bucha vegetal luffa cylindrica

Composite materials arise from the need for lighter materials and with bigger mechanical and thermal resistance. The difficulties of discard, recycling or reuse are currently environmental concerns and, therefore, they are study object of much researches. In this perspective the feasibility of using loofahs (Luffa Cylindrica) for obtainment of a polymeric matrix composite was studied. Six formulations, with 4, 5 and 6 treated layers and untreated, were tested. The loofahs were treated in boiling water to remove lignins, waxes and impurities present in the fibers. After that, they were dried in a direct exposure solar dryer. For the characterization of the composite, thermal (thermal conductivity, thermal capacity, thermal diffusivity and thermal resistivity), mechanical (tensile and bending resistance) and physicochemical (SEM, XRD, density, absorption and degradation) properties were determined. The proposed composite has as advantage the low fiber density, which is around 0.66 g/cm³ (almost half of the polyester resin matrix), resulting in an average composite density of around 1.17g/cm³, 6.0 % lower in relation to the matrix. The treatment carried out in the loofahs increased the mechanical strength of the composite and decreased the humidity absorption. The composite showed lower mechanical behavior than the matrix for all the formulations. The composite also demonstrated itself to be feasible for thermal applications, with a value of thermal conductivity of less than 0.159 W/m.K, ranking it as a good thermal insulator. For all formulations/settings a low adherence between fibers and matrix occurred, with the presence of cracks, showing the fragility due to low impregnation of the fiber by the matrix. This composite can be used to manufacture structures that do not require significant mechanical strength, such as solar prototypes, as ovens and stoves.

Obtenção e caracterização de um compósito de matriz polimérica com carga de bucha vegetal luffa cylindrica

Composite materials arise from the need for lighter materials and with bigger mechanical and thermal resistance. The difficulties of discard, recycling or reuse are currently environmental concerns and, therefore, they are study object of much researches. In this perspective the feasibility of using loofahs (Luffa Cylindrica) for obtainment of a polymeric matrix composite was studied. Six formulations, with 4, 5 and 6 treated layers and untreated, were tested. The loofahs were treated in boiling water to remove lignins, waxes and impurities present in the fibers. After that, they were dried in a direct exposure solar dryer. For the characterization of the composite, thermal (thermal conductivity, thermal capacity, thermal diffusivity and thermal resistivity), mechanical (tensile and bending resistance) and physicochemical (SEM, XRD, density, absorption and degradation) properties were determined. The proposed composite has as advantage the low fiber density, which is around 0.66 g/cm³ (almost half of the polyester resin matrix), resulting in an average composite density of around 1.17g/cm³, 6.0 % lower in relation to the matrix. The treatment carried out in the loofahs increased the mechanical strength of the composite and decreased the humidity absorption. The composite showed lower mechanical behavior than the matrix for all the formulations. The composite also demonstrated itself to be feasible for thermal applications, with a value of thermal conductivity of less than 0.159 W/m.K, ranking it as a good thermal insulator. For all formulations/settings a low adherence between fibers and matrix occurred, with the presence of cracks, showing the fragility due to low impregnation of the fiber by the matrix. This composite can be used to manufacture structures that do not require significant mechanical strength, such as solar prototypes, as ovens and stoves.

Aditivo polimérico derivado de fonte renovável para aplicação em cimento asfáltico de petróleo

This study evaluated the effects of incorporating an additive from an agro-industrial residue, after some chemical modification reactions, to petroleum asphalt cement (CAP) through the polymerization reaction of a viscous polyol obtained by bagasse biomass oxypropylation reaction sugarcane with anhydrides. The polyol is obtained by biomass oxypropylation reaction with propylene oxide, the reaction was performed in an autoclave sealed with pressure and temperature control using 25 mL of OP for every 5 grams of biomass 200°C, which time reaction was two hours. The reaction is revealed by varying the system pressure, initially at atmospheric pressure to reach a maximum pressure value and its subsequent return to atmospheric pressure. For the choice of the most suitable reaction time for polymerization of the polyol with pyromellitic anhydride, the reaction was also conducted in an autoclave sealed with temperature controller (150 ° C) using 20 g of polyol, 1 g of sodium acetate (catalyst) and 8 g of pyromellitic anhydride with the times 30 and 60 minutes. The polymerized materials with different times were characterized by determining the relative viscosity and percentage content of extractable in cyclohexane / ethanol. Given the results with the polymerized material 30 minutes showed the lowest percentage content of extractives and an increased viscosity relative indicating that this time is highlighted with respect to time 60 minutes, because the material is possibly in the form of a crosslinked polymer. Given the choice of time of 30 minutes other polymerization reactions were performed with various anhydrides and other conditions employed different proportions by mass of polyol anhydrides we were referred to as condition I (20 g anhydride and 8 g of polyol), II (20 g anhydride and 20 g of polyol) and III (8 g anhydride and 20 g of polyol). The FTIR spectra of polymeric materials with different polymerization conditions used to prove the occurrence of chemical modification due to the appearance of a characteristic band ester groups (1750 cm-1) present in the polymerized material. He chose to work with the condition III, as is the condition which employs a larger amount of polyol, and even with the smaller amount of anhydride used FTIR spectra revealed that the polymerization reaction was performed. Among the various anhydrides (phthalic, maleic and pyromellitic) of the different conditions used that stood out before the solubility test with solvents analyzed was polymerized material with pyromellitic anhydride because the polymerized material likely in the form of a crosslinked polymer because it was insoluble or poorly soluble in the solvents tested. Polymerization of the polyol with pyromellitic anhydride using condition III, that is, BCPP30, CSPP30, PCPP30 e BCPPG30, provided an increase in thermal stability relative to material in the form of polyol. Applicability tests concerning the incorporation of 16% m / m BCPP30, CSPP30, PCPP30 e BCPPG30 additive in relation to the mass of 600 g CAP showed through characterization tests used, softening point, elastic recovery and marshall dosage, it is possible to use BCPP30 as an additive the conventional CAP, because even with the incorporation of this new additive modified CAP met the specifications of the appropriate standard.

Proposta de uma matriz de indicadores de sustentabilidade para Estarreja

Esta dissertação centra-se na elaboração de uma proposta de matriz de indicadores de sustentabilidade a aplicar ao município de Estarreja. Apesar dos mais recentes desafios e requisitos em matéria de monitorização de planos, projectos e actividades com implicações sobre o ambiente e a sustentabilidade, o acompanhamento da evolução económica, social e ambiental, de uma forma integrada, pelo município tem sido escasso. A literatura da especialidade bem como diversas experiencias municipais nacionais e internacionais têm revelado que a adopção de sistemas de indicadores de sustentabilidade tem um grande potencial não apenas para avaliar o progresso dos municípios em direcção à sustentabilidade ambiental, mas também para induzir melhores formas de governação local. O principal objectivo desta dissertação é a construção de uma matriz de indicadores que avalie a sustentabilidade do município de Estarreja ao nível ambiental. A metodologia adoptada neste trabalho consiste em cinco fases, sendo a primeira fase, a revisão da literatura, através da análise de artigos científicos da especialidade. Na segunda fase é feito o enquadramento legislativo das responsabilidades de monitorização ambiental que cabem aos municípios portugueses. Numa terceira fase, desenvolve-se o levantamento e análise de indicadores sectoriais existentes, já recolhidos e tratados por instituições do Concelho de Estarreja. Na quarta fase procede-se à construção da matriz de indicadores de sustentabilidade, agregando os indicadores já recolhidos pelas iniciativas municipais a um novo conjunto de indicadores de sustentabilidade capazes de analisar a evolução do município no que respeita às pressões sobre o ambiente e sobre os níveis de qualidade ambiental. Na quinta fase são apresentadas as principais conclusões do trabalho e feitas recomendações para tornar exequível e eficiente a monitorização da matriz. O trabalho está organizado em cinco capítulos sendo estes coincidentes com as cinco fases da metodologia. A região de Estarreja tem implantado no seu concelho um dos maiores complexos industriais do país e, em consequência disso, tem vindo a sofrer ao longo dos anos o impacto das actividades industrial e urbana. O procedimento para a construção do sistema de indicadores, bem como a identificação dos eixos temáticos necessários para descrever o contexto que influencia a sustentabilidade do desenvolvimento local, teve por base outros sistemas de indicadores de sustentabilidade local e fornece uma ampla avaliação das características ambientais do município. As dimensões ambientais incluem água, gestão de resíduos, solos, ruído, protecção da natureza, biodiversidade, qualidade do ar, energia e espaços verdes e estão distribuídas por 60 indicadores. Entre estes, 32 já estão a ser monitorizados e 28 foram acrescentados no âmbito deste trabalho. A monitorização dos indicadores propostos não exige grande investimento em capital humano e financeiro, no entanto, constitui um desafio, uma vez que pressupõe a interacção, partilha de informação e transparência por parte das diferentes entidades e empresas municipais.

Medidas de concentração de radônio proveniente de argamassas de cimento portland, gesso e fosfogesso

Portland cement being very common construction material has in its composition the natural gypsum. To decrease the costs of manufacturing, the cement industry is substituting the gypsum in its composition by small quantities of phosphogypsum, which is the residue generated by the production of fertilizers and consists essentially of calcium dihydrate and some impurities, such as fluoride, metals in general, and radionuclides. Currently, tons of phosphogypsum are stored in the open air near the fertilizer industries, causing contamination of the environment. The 226 Ra present in these materials, when undergoes radioactive decay, produces the 222Rn gas. This radioactive gas, when inhaled together with its decay products deposited in the lungs, produces the exposure to radiation and can be a potential cause of lung cancer. Thus, the objective of this study was to measure the concentration levels of 222Rn from cylindrical samples of Portland cement, gypsum and phosphogypsum mortar from the state of Paraná, as well as characterizer the material and estimate the radon concentration in an environment of hypothetical dwelling with walls covered by such materials. Experimental setup of 222Rn activity measurements was based on AlphaGUARD detector (Saphymo GmbH). The qualitative and quantitative analysis was performed by gamma spectrometry and EDXRF with Au and Ag targets tubes (AMPTEK), and Mo target (ARTAX) and mechanical testing with x- ray equipment (Gilardoni) and the mechanical press (EMIC). Obtained average values of radon activity from studied materials in the air of containers were of 854 ± 23 Bq/m3, 60,0 ± 7,2 Bq/m3 e 52,9 ± 5,4 Bq/m3 for Portland cement, gypsum and phosphogypsum mortar, respectively. These results extrapolated into the volume of hypothetical dwelling of 36 m3 with the walls covered by such materials were of 3366 ± 91 Bq/m3, 237 ± 28 Bq/m3 e 208 ± 21 Bq/m3for Portland cement, gypsum and phosphogypsum mortar, respectively. Considering the limit of 300 Bq/m3 established by the ICRP, it could be concluded that the use of Portland cement plaster in dwellings is not secure and requires some specific mitigation procedure. Using the results of gamma spectrometry there were calculated the values of radium equivalent activity concentrations (Raeq) for Portland cement, gypsum and phosphogypsum mortar, which were obtained equal to 78,2 ± 0,9 Bq/kg; 58,2 ± 0,9 Bq/kg e 68,2 ± 0,9 Bq/kg, respectively. All values of radium equivalent activity concentrations for studied samples are below the maximum level of 370 Bq/kg. The qualitative and quantitative analysis of EDXRF spectra obtained with studied mortar samples allowed to evaluate quantitate and the elements that constitute the material such as Ca, S, Fe, and others.

Otimização e validação de um método para o preparo de suspensões e determinação de fulereno n-C60 em matriz aquosa

Com o aumento da produção do fulereno C60 e sua aplicação comercial é previsível que este composto acabe sendo liberado no ambiente, tornando-se um contaminante. Em razão das suas características físico-químicas e sua capacidade de formar agregados (n-C60) quando em contato com a água, o C60 pode se tornar um carreador de outros contaminantes (como metais e compostos orgânicos), facilitando a sua entrada nos organismos. Neste sentido, a sua toxicidade (tanto de forma isolada como em associação com outros contaminantes) vem sendo avaliada. Sendo assim, a fim de viabilizar os estudos com C60, uma metodologia para preparo de suspensões aquosas foi validada, sendo quantificada por CLAE/UV-Vis. As suspensões foram preparadas sem a adição de solvente de duas formas distintas, com aquecimento (50ºC) e à temperatura ambiente (≈20 ºC), onde se mantiveram sob agitação constante e exposição à luz artificial por até 2 meses. A cada 15 dias a suspensão foi quantificada. Além disso, três métodos distintos de extração e pré-concentração (extração líquido-líquido (ELL), extração em fase sólida (EFS) e micro-extração dispersiva líquido-líquido (MEDLL)) foram validados e comparados quanto a sua eficiência. Coeficientes de correlação ≥ 0,99 foram obtidos para as curvas de calibração. Os LDM e LQM foram de 0,08 e 0,3 ng mL-1 para EFS e ELL, considerando o fator de concentração de 500 vezes, e de 0,8 e 3,0 ng mL-1 para a MEDLL, considerando o fator de concentração de 50 vezes, respectivamente. A precisão (intermediária e repetitividade) variou entre 0,46 e 4,03 (%RSDpi) e entre 0,69 e 3,59 (%RSDr), enquanto que a exatidão ficou entre 72,3 e 85,6% para ELL, 86,1 e 115,5% para a EFS e 87,9 e 111,4% para MEDLL. Com base nestes parâmetros relativos a análise de suspensões aquosas de C60, a EFS foi considerada o método mais eficiente. O aquecimento se mostrou relevante no tamanho dos agregados, que foram significativamente maiores na suspensão sem aquecimento, porém o tempo de preparo da suspensão não influenciou na concentração final da suspensão. Portanto, recomenda-se o preparo das suspensões aquosas de C60 sem aquecimento por um período de agitação de 30-45 dias.

Avaliação da técnica de dispersão da matriz em fase sólida assistida por vórtex para análise de fármacos em peixes

Os fármacos classificados como contaminantes orgânicos emergentes tornaramse tópico de discussão ambiental pois estes são capazes de atingir diferentes matrizes do meio ambiente, como água, solo e organismos aquáticos, e estudos demonstrando a toxicidade tem despertado o interesse científico. Neste estudo um método analítico foi otimizado e validado para determinação de quinze fármacos em amostras de peixes empregando preparo de amostras por dispersão da matriz em fase sólida (MSPD) assistida por vórtex e determinação por cromatografia líquida acoplada a espectrometria de massas sequencial (LC-MS/MS). O estudo ainda focou na aplicação de diferentes suportes sólidos na etapa de dispersão da MSPD, sendo que três (quitina, quitosana e concha de mexilhão dourado) foram utilizados pela primeira vez para esta finalidade, O método otimizado foi validado seguindo os parâmetros do INMETRO, ANVISA, SANCO e FDA. A curva analítica e linearidade foram avaliados através da calibração externa e superposição na matriz. Os compostos demonstraram linearidade dentro da faixa recomendada, com coeficiente de correlação maior do que 0,99. Os limites de detecção do método variaram de 1 a 100 ng g -1 , e os limites de quantificação a variaram de 5 a 1000 ng g -1 . Os valores de recuperação variaram de 68% a 108%, com RSD menores que 13% para todos os compostos. O efeito de matriz foi avaliado e quatro dos quinze compostos apresentaram efeito maior que ±20%. Na aplicabilidade o método demonstrou ser eficiente para extração de fármacos de diferentes espécies de peixe, apresentando exatidão e precisão adequados. Não foram encontrados resíduos de fármacos nas amostras analisadas.

Proposta de uma matriz de decisão em energia hidrelétrica com o uso do método multicritério, para formulação de políticas públicas no estado do Paraná

Brazil is internationally acknowledged for its renewable sources, most notably, hydroelectric power plant projects which correspond to 65% of electricity production supply to the National Interconnected System. The main question behind this research is: what are the weights and the relative importance of the variables which have influence on the decision making process for the expansion of hydroelectric generation projects in Parana? The main objective is to propose a multi-criteria decision procedure, in association with water sources options that take into consideration the weight and relative importance of the alternatives having influence on the decision by enterprises in the generation of electricity in the state of Paraná. As far as the approach to the problem is concerned, this research can be classified as having mixed methodologies, applying Content Analysis, Delphi technique and the Analytic Hierarchy Process. Following Delphi methodology, a group of 21 was selected for data collection, all of those linked to Paranaense hydroelectricity market. And the main result was the construction of a decision tree in which it was possible to identify the importance and relative weight of the elements associated with the four dimensions of energy. In environmental dimension, the highest relative weight was placed on the loading capacity of Parana system; the economic dimension, the amortization of investment; in social dimension, the generation of direct work places and in institutional dimension, the availability of suitable sources of financing. Policy makers and business managers make their decisions based on specific criteria related to the organization segment, market information, economic and political behavior among other indicators that guide them in dealing with the typical tradeoffs of projects in hydropower area. The results obtained in the decision tree show that the economic bias is still the main factor in making investment decisions. However, environmental impacts on the State loading capacity, income generation, providing opportunities for direct as well as indirect jobs. And at an institutional level, the absence of funding sources show that the perception of experts is focused on other issues beyond the logic behind development per se. The order of priority of variables in this study indicates that in the current environment of uncertainty in the Brazilian economy as many variables must be analyzed and compared in order to optimize the scarce resources available to expand local development in relation to Paranaense water matrix.

Modelizado molecular de nanocomposites de matriz polimérica reforzados con nanotubos de carbono

135 p.

Dispersão de sementes por aves na galeria ripícola e matriz envolvente

As galerias ripícolas são habitats com uma grande disponibilidade de recursos alimentares e abrigo para a fauna, estando entre os habitats mais importantes e vulneráveis do mundo. São uma fonte de produção de frutos, o que atrai muitos animais, como as aves frugívoras, que são os principais dispersores de sementes na bacia do Mediterrâneo. O objetivo principal deste estudo foi estudar os padrões de dispersão de sementes por aves na interface galeria ripícola-matriz florestal envolvente (Montado). Foram marcadas com fluorescência plantas-mãe produtoras de frutos, e utilizadas armadilhas para sementes e transectos, para a recolha dos dejetos de aves onde, posteriormente, se detetaram as sementes dispersadas. Constatou-se que a dispersão de sementes e a abundância de plantas-mãe foi superior a distâncias mais próximas da ribeira, diminuindo à medida que esta distância aumenta. A espécie mais dispersada foi Smilax aspera e as espécies com sementes de menor dimensão, foram dispersadas a uma maior distância da planta-mãe, provavelmente devido a este tipo de sementes permanecerem mais tempo no trato intestinal das aves. Os resultados deste estudo apresentam algumas implicações para a colonização da matriz adjacente por plantas produtoras de frutos; ABSTRACT: Riparian galleries are habitats with a large availability food resources and shelter for animals, being among the most important and vulnerable habitats in the world. These zones are a great source of fruits attracting many animals, such as frugivorous birds, which are the main seed dispersers in the Mediterranean basin. The objective of this thesis is the study of seed dispersal patterns by birds, in the riparian gallery and in the surrounding forest matrix (Montado). Fruits of several plant species were used to collect bird droppings and detect fluorescent seeds in those droppings. Fruit abundance and seed dispersal were higher close to the stream, and decreased rapidly with an increase in distance from the stream. From all species, the most dispersed was Smilax aspera and species with smaller seed were found at a significantly larger distance from parents plants than species with large seeds. This can be explained by the fact that smaller seed stay longer in the intestinal tract of the birds. The results of this study present some implications for the colonization of freshly fruit plants from the riparian gallery into the adjacent matrix.

Adição de superplastificante e anti-segregante à base de CMC em pastas de cimento para Poços de Petróleo

Oil well cementing materials consist of slurries of Special class Portland cement dispersed in water. Admixtures can be used to provide the necessary fluidity, so the material can be efficiently pumped down as well as penetrate porous rocks with controlled filter loss. Construction admixtures can be used to modify the properties of oil well cements provided they can withstand and hold their properties at the higher than ambient temperatures usually encountered in oil fields. In civil construction, superplasticizer play the role of dispersants that reduce the facto r of water cement improve mechanical properties and fluidity of the cement, whereas anti-segregation agents improve the workability of the slurry. In the present study, oil well cement slurries were produced adding both a dispersant and an anti-segregation agent conventionally used in Portland CPII-Z-32 RS cement aiming at materials for primary cementing and squeeze operations. Three basic aspects were evaluated: fluidity, filter loss and the synergetic effect of the admixtures at two temperatures, i.e., 27°C and 56°C, following API RP 10B practical recommendations. The slurries were prepared using admixture concentrations varying from 2.60 Kgf/m3 (0.02 gallft3) to 5.82 Kgf/m3 (0.045 galJft3) BWOC. The density of the slurries was set to 1.89 g/cm3 (15.8 Ib/gal). 0.30 to 0.60% BWOC of a CMC-based anti-segregation agent was added to the cement to control the filter loss. The results showed that the addition of anti-segregation at concentrations above 0.55% by weight of cement resulted in the increased viscosity of the folders in temperatures evaluated. The increasing the temperature of the tests led to a reduction in the performance of anti-segregation. At concentrations of 5.20 kgf/m3 (0,040 gallft3) and 5.82 Kgf/m3 (0,045 gal/ft 3) observed a better performance of the properties evaluated in the proposed system. At low temperature was observed instability in the readings of rheology for all concentrations of anti-segregation. Contents that increasing the concentration of anti¬-segregation is limited concentrations greater than 0.55 % BWOC of the CMC in temperature analyzed. The use of the system with CMC promoted a good performance against the properties evaluated. The principal function of anti¬-segregation was optimized with increasing concentration of superplasticizer, at temperatures above the 2rC. The study of the behaviour of systemic additives, resulting in slurries of cement, which can be optimized face studies of other intrinsic properties in oil fields