Análise estatística da vida em fadiga de compósitos estruturais pela distribuição de Weibull

Nowadays technological trend is based on finding materials that could support low weight with satisfactory mechanical properties and for this reason composite material became a very attractive topic in research projects all over the world. Due to its heterogenic properties, this type of material shows scatter in mechanical test results, especially in cyclic loading. Therefore it is important to predict its fatigue strength behaviour by statistic analysis, once fatigue causes approximately 90% of the failure in structural components. The present work aimed to investigate the fatigue behaviour of the Twill/Cycom 890 composite, which is carbon fiber reinforced with polymeric resin as matrix and manufactured via RTM process (Resin Transfer Molding). All samples were tested in different tensile level in triplicate in order to associate these values. The statistical analysis was conducted with Two-Parameter Weibull Distribution and then evaluated the fatigue life results for the composite. Weibull graphics were used to determine the scale and shape parameters. The S-N curve for the Twill/Cycom composite was drawn and indicated the number of cycles to occur the first damages in this material. The probability of failure was associated with material reliability, as shown in graphics for the different tensile levels and fatigue life. In addition, the laminate was evaluated by ultrasonic inspection showing a regular impregnation. The fractographic analysis conducted by SEM showed failure mechanisms for polymeric composites associated to cyclic loadings ... (Complete abstract click electronic access below)

Controle de Qualidade em Raios X Odontológico Periapical

The purpose of this work is to provide quality control requirements and security in dental x-rays in order to obtain good quality image which allows the correct diagnosis, which reduces the dose to the patient, mainly due to the repetition of tests, and decreasing cost. The requirements apply to related activities to quality control and procedures using ionizing radiation for diagnostic imaging in dentistry by evaluating a minimum set of parameters to be tested or verified. Quality control follows the Ordinance No. 453 of the Ministry of Health of 06.01.1998, SS Resolution No. 625 of 12.14.1994 and Resolution No. 64 of the Health Surveillance Center – Department of Health of Sao Paulo and National Health Surveillance Agency – Ministry of Health of Brazil. This study was conducted in the city of Marilia, Sao Paulo, along with the Company P&R Consulting and Medical Physics, in a dental clinic of the University UNIMAR in the x-ray equipment used on that site. The physical parameters of the device were tested with the aid of ionization chambers to measure rates of radiation, electrometer to measure rates of time, kV and doses, radiographic films and positioning devices. Finally, this work demonstrates the need and importance of quality control, which one ensures the proper use of x-ray machines, maintaining efficiency and at the same time it reduces the risks to the patient, to the dentist and to the general public

Obtenção e caracterização de compósitos via RTM com alta fração de fibras de carbono processados à temperatura ambiente

After confirming the high specific mechanical properties of composite materials by scientific studies conducted over the last decades, one of the challenges of this new class of materials is the ability to achieve mass production at a more affordable cost, which has become indispensable. The Resin Transfer Molding (RTM) is an excellent method for manufacturing composite materials. Despite being a process widely used by international companies in the production of high performance structural composites, only a short time the national aviation industry has shown interest in implementing this type of processing to more complex structures and greater structural responsibility. In aeronautical projects, the reproducibility and the relative low cost of this process, several studies have been performed in Brazil for learning and perfecting this technique. This process is suitable for producing polymer components both simple as complex geometry, and allows to achieve consistent thickness, with high quality finish and without limiting range. Polymeric composite components for the high mechanical stress applications such as aircraft structures, satellites, etc., require a strict control of volume fractions of the composite constituents, beyond the knowledge of their mechanical and thermal properties. Therefore, in this experimental work degree study on the mechanical, thermal and of porosity composites processed by RTM processed characterization was performed. This characterization was performed targeting a possible aerospace application of this composite material. For the production of composites, process equipment (RTM RTM injector Radius 2100cc) was used. The processed carbono/epoxy composites were characterized via flexure tests mechanically and thermally analysis via DMA, DSC and TGA. To determine the volume fraction of fibers, the composite samples were analyzed via matrix digestion (ASTM D3171) ... (Complete abstract click electronic access below)

Estudo das propriedades físicas em materiais vítreos do sistema 50B2O3 - 15CuO - 20Li2O - 15X (X= Na2O, K2O, RbCI e Cs2O)

The increasing demand for devices for solid state applications in many technological areas has resulted in a high demand for new materials. Among these material have the advantage of being manufactured with different chemical compositions, and may have physical properties equal to or higher than the corresponding crystalline material. The aim of this paper was to produce borate glass system 50B2O3 – 15CuO – 20Li2O – 15X (X = Na2O, K2O, RbCl e Cs2O) to analyze the influence of the atomic radius of alkali in the physical properties of this glass system. The glasses were synthesized by the process of melting and molding. The characteristic temperatures were determined by the technique of scanning calorimetry (DSC). The non-crystalline was determined by x-ray diffraction. In order to determine the molar volume a density measurement by using the Archimedes method was used. The structural characterization was carried out using the technique of infrared spectroscopy

Reciclagem de poliestireno expandido: compósito com fibras de sisal para confecção de placas de circuito impresso

In this work polystyrene composites reinforced with recycled sisal fibers were processed, in order to apply in the manufacture of printed circuit boards. A thermoplastic matrix of recycled polystyrene was used, this material came from waste expanded polystyrene (EPS) used in appliance's packages. Composites were prepared with 15% and 25% of sisal fibers. To obtain the composites, wasted EPS and natural sisal fibers were chosen, to encourage recycling and reuse of household waste and also the use of renewable resources. The composites were analyzed by standard tensile and flexural test, in order to verify the mechanical properties of the material. The characterization of the composite was done by scanning electron microscopy (SEM) , thermogravimetry (TGA / DTG) , differential scanning calorimetry (DSC) and dielectric analysis . The analysis of the results showed that the percentage of fibers in the composite influences directly the thermal and mechanical properties. Plates with a lower percentage of fibers showed superior properties at a higher percentage. The composite material obtained is easy to process and it's use is feasible for the confection of printed circuit boards, considering it's mechanical, thermal and insulative properties

Cálculo estrutural de barreiras: Desenvolvimento de um programa computacional de interface online

This study aimed to develop a computer program which systematizes the structural shielding design calculation in diagnostic radiology facilities. For this purpose methodology of the National Council of Radiation Protection and Measurements (NCRP 147[5]) was used. By comparative statistics studies, it was verified if reference parameters values suggested by the US publication correspond to the average national values. The World Wide Web was chosen because of its characteristics as a powerful mean of communication, especially in terms of the wide variety of useful resources and easy access. To compare the reference values of some parameters proposed by NCRP 147 to Brazilian average, studies about the normalized workload per patient, performance of X-ray tube and primary air kerma, unshielded, at one meter from the focal point of the X-ray tube were made. Through this research, relative differences were found. In workload values this differences reached up to 50% in mammography compared to those presented by the NCRP 147; in X-ray tube performance the percentage differences reached 69% in dental radiology, and air kerma results amounted 31% in fluoroscopy. This demonstrates the importance of validation of international protocols to local realities

Flexão e análise dinâmico-mecânica de compósitos 5HS e NCF com resina epóxi monocomponente produzidos por RTM

In order to study resin distribution and homogeneity of composite laminates manufactured by RTM, it was used CYCOM 890 monolithic toughened epoxy as a matrix with two different configurations of intermediated modulus (IM) carbon fibers: Satin Weave (5HS) and non crimp fabric (NCF). The injection parameters were defined based on Thermo Gravimetric Analysis (TG), Differential Scanning Calorimetry (DSC) and rheological analysis. After processing the material, the resin/fiber impregnation was studied using ultrasonic test, Thermo Gravimetric Analysis, Differential Scanning Calorimetry, Dynamic Mechanical Analysis (DMA) and flexural tests. Therefore, it was able to observe an internal residual stress during the cooling process in both laminates, higher in the composite using NCF fabric due to the lack of symmetry, although a good proportion of fiber/matrix has been verified by the lower values of flexural modulus deviation. The DMA enabled the visualization of glass transition and its association with the inter and intra molecular interaction and movement, in which the NCF composite presented better permeability due to the lowest temperature of glass transition, when compared to the Satin Weave composite

Avaliação dos efeitos ambientais nas propriedades do compósito de poliamida 6,6/fibras de carbono

This graduation work done study of polyamide 6.6/composite carbon fibres, since its processing, characterization of the main properties. Besides the influence of temperature, UV radiation, salt spray and moisture on the mechanical and viscoelastic behavior. To achieve this goal, the first composite was processed from the heat compression molding using known variables of the process and using the empirical method to find the best value for other parameters. The method processing molding was chosen because it common in composites processing in order to evaluate the influence of crystallinity of the properties that influence the mechanical and viscoelastic behavior laminates. From the obtained laminate specimens were evaluated in weathering, such as: in hygrothermal chamber, UV, salt spray and thermal shock. In another step, the effect produced by these constraints were evaluated by optical microscopy, ultrasound, dynamic mechanical analysis and vibration tests. This project was conducted at the Department of Technology and Materials of UNESP in Guaratingueta, where all the equipment and techniques for the implementation of this project met available. After the tests proved the applicability of the composite polyamide 6.6/carbon fibers in aeronautical applications with resistance the main climatic influences

Estudo da modificação superficial de fibras de carbono por meio de tratamentos a plasma para o aumento da adesão na interface de compósitos fibra de carbono/PPS

Pós-graduação em Engenharia Mecânica - FEG

Condição periodontal, perda dentária e diferenças socioeconômicas em adultos e idosos brasileiros

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Alternativa de tratamento simplificado e integrado da retenção intraóssea de incisivo central superior, associada a odontoma: relato de caso

Permanent teeth impaction is highly prevalent among brazilian people. Its etiology is related to local and general factors association. Permanent teeth retention compromises dental occlusion and when anterior teeth are involved, it also brings esthetics impairments which lead to psychological disturbance. Early diagnosis and adequate treatment are extremely important to solve not only occlusal problems but also psychological aspects. Orthodontic traction of impacted teeth can be conducted by using fixed or removable appliances. Although it depends on patient compliance the use of removable appliances provides an anchorage based on the teeth and the palate reducing undesirable side effects. This paper describes the case of a fourteen years old female patient whose right maxillary central incisor was adequately tractioned with a removable orthodontic appliance. Removable orthodontic devices were used at first to reposition teeth in maxillary anterior area what provided adequate space to allow the placement of the impacted incisor and after were also used to traction and position this tooth. The procedure described seemed to be effective, non expensive and a viable treatment to be performed even on the scope of public health services, extending orthodontic treatment to a higher number of patients.

Cárie oculta extensa: relato de caso clínico

The pattern of caries lesions has been modified over decades. If the presence or absence of a caries lesion is based upon only a visual examination, its diagnosis might become underestimated since dentinal lesions underneath non cavitated or minimally demineralized enamel is highly frequent in dental clinics. The aim of this paper is to report a clinical case of a child with an upper molar with questionable occlusal aspect, presenting asymptomatic pulpal hyperplasia on the distolingual pit. Periapical radiographic examination was essential for diagnosing hidden caries and elaborating the treatment plan. As part of the approach, removal of the decayed tissue and pulpotomy with calcium hydroxide were performed. The association of an accurate visual examination to an adequate oral radiographyis is extremely important in cases which the presence of hidden caries is doubtful. As a result, an early diagnosis and the reduction of more invasive interventions related to the oral health care of pediatric patients can be achieved as well.

Association between post-orthodontic treatment gingival margin alterations and symphysis dimensions

Orthodontic therapy is known to be associated with the development of gingival recession. Several factors may be involved in the causal chain of this outcome, including anatomical and behavioral aspects. Among the anatomical aspects, the dimensions of the mandibular symphysis could play a predisposing role. This study evaluated the relationship between the mandibular symphysis dimensions prior to orthodontic therapy and the development of gingival recessions on the lower incisors and cuspids. Records from 189 orthodontically treated adolescents were evaluated, including radiographs, casts and intra-oral photographs. Symphysis dimensions were assessed by cephalograms. Gingival margin alterations were determined in photographs and cast models. Association between gingival margin alterations and symphysis dimensions was tested by chi-square (α=0.05). Occurrence of gingival recession increased after orthodontic therapy. No association was observed on average of symphysis dimensions and the occurrence of gingival recessions. It may be concluded that pretreatment symphysis dimensions may not be used as predictors of gingival recession after orthodontic therapy.

Contaminación microbiana en las líneas de agua de las unidades odontológicas

Introduction and Objective: Microorganisms are responsible for multiple infections and pathologies; this is why it is important to control microbes that can be found in the triple syringe used for irrigation in different dental procedures. The aim of this study was to identify cultivable species of microbes (fungus and bacteria) found in some dental units water lines of a private dental clinic from Medellín, Colombia. Materials and Methods: Random samples were taken from 11 chairs from a total of 89; a sample of water of 500ml was collected from the triple syringe of each selected chair. The study aim to search for the presence of total coliforms, filamentous fungi and leavened Results: the average presence of microorganisms was between 40CFU and more of 200 CFU. Microorganisms such as Aeromona salmonicida, Actinobacilus sp and Pseudomona maltophil were isolated. No total coliforms neither fecal coliforms were found. Conclusions: the high levels of contamination suggest that there is a mature biofilm in somewhere of the dental unit water line, but the absence of total and fecalis coliforms suggest that the water had been treated.

Tratamiento de maloclusión classe II división 1 con el aparato de Herbst tipo férula, después del pico de crecimiento puberal

Malocclusion class II-1, is represented by a high prevalence in Brazil, being something common in orthodontic practice. One of the main characteristics of this malocclusion is jaw retrusion, by what many devices of jaw advance are presented in the literature. Being one of them Herbst's device, which is a functional and fixed device created by Emil Herbst (1905) and updated by Hans Pancherz in the decade of 80s.This device is characterized by keeping the jaw advance in a continuous way, while presenting a less active treatment, leading to an immediate aesthetic impact, and the patient cooperation is not required. To improve the anchoring and prevent the collapse of the apparatus was set up last amended version of it by Dr Raveli quoted as Herbst splint. Recent research indicates the use of this device after the peak pubertal growth, creating an appropriate response condylar. The aim of this work is to show the orthodontist a choice of how to use the splint Herbst in Class malocclusions II-1.