Study of the calibration method of pressure-velocity probes and its application in a field of progressive plane waves

This dissertation presents a calibration procedure for a pressure velocity probe. The dissertation is divided into four main chapters. The first chapter is divided into six main sections. In the firsts two, the wave equation in fluids and the velocity of sound in gases are calculated, the third section contains a general solution of the wave equation in the case of plane acoustic waves. Section four and five report the definition of the acoustic impedance and admittance, and the practical units the sound level is measured with, i.e. the decibel scale. Finally, the last section of the chapter is about the theory linked to the frequency analysis of a sound wave and includes the analysis of sound in bands and the discrete Fourier analysis, with the definition of some important functions. The second chapter describes different reference field calibration procedures that are used to calibrate the P-V probes, between them the progressive plane wave method, which is that has been used in this work. Finally, the last section of the chapter contains a description of the working principles of the two transducers that have been used, with a focus on the velocity one. The third chapter of the dissertation is devoted to the explanation of the calibration set up and the instruments used for the data acquisition and analysis. Since software routines were extremely important, this chapter includes a dedicated section on them and the proprietary routines most used are thoroughly explained. Finally, there is the description of the work that has been done, which is identified with three different phases, where the data acquired and the results obtained are presented. All the graphs and data reported were obtained through the Matlab® routine. As for the last chapter, it briefly presents all the work that has been done as well as an excursus on a new probe and on the way the procedure implemented in this dissertation could be applied in the case of a general field.

Woman wiring fluorescent light

Inscriptions: Verso: [stamped] Photograph by Freda Leinwand. [463 West Street, Studio 229G, New York, NY 10014].

Woman wiring fluorescent light

Inscriptions: Verso: [stamped] Photograph by Freda Leinwand. [463 West Street, Studio 229G, New York, NY 10014].

Woman wiring fluorescent light

Inscriptions: Verso: [stamped] Photograph by Freda Leinwand. [463 West Street, Studio 229G, New York, NY 10014].

Design rationnel de nanothermomètres programmables à base d’ADN

Développer de nouveaux nanomatériaux, interrupteurs et machines nanométriques sensibles à de petites variations de température spécifiques devrait être de grande utilité pour une multitude de domaines œuvrant dans la nanotechnologie. De plus, l’objectif est de convaincre le lecteur que les nanotechnologies à base d’ADN offrent d’énormes possibilités pour la surveillance de température en temps réel à l’échelle nanométrique. Dans la section Résultats, nous exploitons les propriétés de l’ADN pour créer des thermomètres versatiles, robustes et faciles à employer. En utilisant une série de nouvelles stratégies inspirées par la nature, nous sommes en mesure de créer des nanothermomètres d’ADN capables de mesurer des températures de 25 à 95°C avec une précision de <0.1°C. En créant de nouveaux complexes d’ADN multimériques, nous arrivons à développer des thermomètres ultrasensibles pouvant augmenter leur fluorescence 20 fois sur un intervalle de 7°C. En combinant plusieurs brins d’ADN avec des plages dynamiques différentes, nous pouvons former des thermomètres montrant une transition de phase linéaire sur 50°C. Finalement, la vitesse de réponse et la précision des thermomètres développés et leur réversibilité sont illustrées à l’aide d’une expérience de surveillance de température à l’intérieur d’un unique puits d’un appareil de qPCR. En conclusion, les applications potentielles de tels nanothermomètres en biologie synthétique, imagerie thermique cellulaire, nanomachines d’ADN et livraison contrôlée seront considérées.

Mechanochemistry for Active Materials and Devices

The coupling of mechanical stress fields in polymers to covalent chemistry (polymer mechanochemistry) has provided access to previously unattainable chemical reactions and polymer transformations. In the bulk, mechanochemical activation has been used as the basis for new classes of stress-responsive polymers that demonstrate stress/strain sensing, shear-induced intermolecular reactivity for molecular level remodeling and self-strengthening, and the release of acids and other small molecules that are potentially capable of triggering further chemical response. The potential utility of polymer mechanochemistry in functional materials is limited, however, by the fact that to date, all reported covalent activation in the bulk occurs in concert with plastic yield and deformation, so that the structure of the activated object is vastly different from its nascent form. Mechanochemically activated materials have thus been limited to “single use” demonstrations, rather than as multi-functional materials for structural and/or device applications. Here, we report that filled polydimethylsiloxane (PDMS) elastomers provide a robust elastic substrate into which mechanophores can be embedded and activated under conditions from which the sample regains its original shape and properties. Fabrication is straightforward and easily accessible, providing access for the first time to objects and devices that either release or reversibly activate chemical functionality over hundreds of loading cycles.

While the mechanically accelerated ring-opening reaction of spiropyran to merocyanine and associated color change provides a useful method by which to image the molecular scale stress/strain distribution within a polymer, the magnitude of the forces necessary for activation had yet to be quantified. Here, we report single molecule force spectroscopy studies of two spiropyran isomers. Ring opening on the timescale of tens of milliseconds is found to require forces of ~240 pN, well below that of previously characterized covalent mechanophores. The lower threshold force is a combination of a low force-free activation energy and the fact that the change in rate with force (activation length) of each isomer is greater than that inferred in other systems. Importantly, quantifying the magnitude of forces required to activate individual spiropyran-based force-probes enables the probe behave as a “scout” of molecular forces in materials; the observed behavior of which can be extrapolated to predict the reactivity of potential mechanophores within a given material and deformation.

We subsequently translated the design platform to existing dynamic soft technologies to fabricate the first mechanochemically responsive devices; first, by remotely inducing dielectric patterning of an elastic substrate to produce assorted fluorescent patterns in concert with topological changes; and second, by adopting a soft robotic platform to produce a color change from the strains inherent to pneumatically actuated robotic motion. Shown herein, covalent polymer mechanochemistry provides a viable mechanism to convert the same mechanical potential energy used for actuation into value-added, constructive covalent chemical responses. The color change associated with actuation suggests opportunities for not only new color changing or camouflaging strategies, but also the possibility for simultaneous activation of latent chemistry (e.g., release of small molecules, change in mechanical properties, activation of catalysts, etc.) in soft robots. In addition, mechanochromic stress mapping in a functional actuating device might provide a useful design and optimization tool, revealing spatial and temporal force evolution within the actuator in a way that might also be coupled to feedback loops that allow autonomous, self-regulation of activity.

In the future, both the specific material and the general approach should be useful in enriching the responsive functionality of soft elastomeric materials and devices. We anticipate the development of new mechanophores that, like the materials, are reversibly and repeatedly activated, expanding the capabilities of soft, active devices and further permitting dynamic control over chemical reactivity that is otherwise inaccessible, each in response to a single remote signal.

Design rationnel de nanothermomètres programmables à base d’ADN

Développer de nouveaux nanomatériaux, interrupteurs et machines nanométriques sensibles à de petites variations de température spécifiques devrait être de grande utilité pour une multitude de domaines œuvrant dans la nanotechnologie. De plus, l’objectif est de convaincre le lecteur que les nanotechnologies à base d’ADN offrent d’énormes possibilités pour la surveillance de température en temps réel à l’échelle nanométrique. Dans la section Résultats, nous exploitons les propriétés de l’ADN pour créer des thermomètres versatiles, robustes et faciles à employer. En utilisant une série de nouvelles stratégies inspirées par la nature, nous sommes en mesure de créer des nanothermomètres d’ADN capables de mesurer des températures de 25 à 95°C avec une précision de <0.1°C. En créant de nouveaux complexes d’ADN multimériques, nous arrivons à développer des thermomètres ultrasensibles pouvant augmenter leur fluorescence 20 fois sur un intervalle de 7°C. En combinant plusieurs brins d’ADN avec des plages dynamiques différentes, nous pouvons former des thermomètres montrant une transition de phase linéaire sur 50°C. Finalement, la vitesse de réponse et la précision des thermomètres développés et leur réversibilité sont illustrées à l’aide d’une expérience de surveillance de température à l’intérieur d’un unique puits d’un appareil de qPCR. En conclusion, les applications potentielles de tels nanothermomètres en biologie synthétique, imagerie thermique cellulaire, nanomachines d’ADN et livraison contrôlée seront considérées.

X-ray fluorescent (XRF) ratios and diatom groups of sediment core GeoB13813-4

The continental shelf adjacent to the Río de la Plata (RdlP) exhibits extremely complex hydrographic and ecological characteristics which are of great socioeconomic importance. Since the long-term environmental variations related to the atmospheric (wind fields), hydrologic (freshwater plume), and oceanographic (currents and fronts) regimes are little known, the aim of this study is to reconstruct the changes in the terrigenous input into the inner continental shelf during the late Holocene period (associated with the RdlP sediment discharge) and to unravel the climatic forcing mechanisms behind them. To achieve this, we retrieved a 10 m long sediment core from the RdlP mud depocenter at 57 m water depth (GeoB 13813-4). The radiocarbon age control indicated an extremely high sedimentation rate of 0.8 cm per year, encompassing the past 1200 years (AD 750-2000). We used element ratios (Ti / Ca, Fe / Ca, Ti / Al, Fe / K) as regional proxies for the fluvial input signal and the variations in relative abundance of salinity-indicative diatom groups (freshwater versus marine-brackish) to assess the variability in terrigenous freshwater and sediment discharges. Ti / Ca, Fe / Ca, Ti / Al, Fe / K and the freshwater diatom group showed the lowest values between AD 850 and 1300, while the highest values occurred between AD 1300 and 1850. The variations in the sedimentary record can be attributed to the Medieval Climatic Anomaly (MCA) and the Little Ice Age (LIA), both of which had a significant impact on rainfall and wind patterns over the region. During the MCA, a weakening of the South American summer monsoon system (SAMS) and the South Atlantic Convergence Zone (SACZ), could explain the lowest element ratios (indicative of a lower terrigenous input) and a marine-dominated diatom record, both indicative of a reduced RdlP freshwater plume. In contrast, during the LIA, a strengthening of SAMS and SACZ may have led to an expansion of the RdlP river plume to the far north, as indicated by higher element ratios and a marked freshwater diatom signal. Furthermore, a possible multidecadal oscillation probably associated with Atlantic Multidecadal Oscillation (AMO) since AD 1300 reflects the variability in both the SAMS and SACZ systems.

Numerical Modelling of Eddy Current Probes for CANDU® Fuel Channel Inspection

Multi-frequency Eddy Current (EC) inspection with a transmit-receive probe (two horizontally offset coils) is used to monitor the Pressure Tube (PT) to Calandria Tube (CT) gap of CANDU® fuel channels. Accurate gap measurements are crucial to ensure fitness of service; however, variations in probe liftoff, PT electrical resistivity, and PT wall thickness can generate systematic measurement errors. Validated mathematical models of the EC probe are very useful for data interpretation, and may improve the gap measurement under inspection conditions where these parameters vary. As a first step, exact solutions for the electromagnetic response of a transmit-receive coil pair situated above two parallel plates separated by an air gap were developed. This model was validated against experimental data with flat-plate samples. Finite element method models revealed that this geometrical approximation could not accurately match experimental data with real tubes, so analytical solutions for the probe in a double-walled pipe (the CANDU® fuel channel geometry) were generated using the Second-Order Vector Potential (SOVP) formalism. All electromagnetic coupling coefficients arising from the probe, and the layered conductors were determined and substituted into Kirchhoff’s circuit equations for the calculation of the pickup coil signal. The flat-plate model was used as a basis for an Inverse Algorithm (IA) to simultaneously extract the relevant experimental parameters from EC data. The IA was validated over a large range of second layer plate resistivities (1.7 to 174 µΩ∙cm), plate wall thickness (~1 to 4.9 mm), probe liftoff (~2 mm to 8 mm), and plate-to plate gap (~0 mm to 13 mm). The IA achieved a relative error of less than 6% for the extracted FP resistivity and an accuracy of ±0.1 mm for the LO measurement. The IA was able to achieve a plate gap measurement with an accuracy of less than ±0.7 mm error over a ~2.4 mm to 7.5 mm probe liftoff and ±0.3 mm at nominal liftoff (2.42±0.05 mm), providing confidence in the general validity of the algorithm. This demonstrates the potential of using an analytical model to extract variable parameters that may affect the gap measurement accuracy.

Quantifying Aflatoxin B1 in peanut oil using fabricating fluorescence probes based on upconversion nanoparticles

Rare earth doped upconversion nanoparticles convert near-infrared excitation light into visible emission light. Compared to organic fluorophores and semiconducting nanoparticles, upconversion nanoparticles (UCNPs) offer high photochemical stability, sharp emission bandwidths, and large anti-Stokes shifts. Along with the significant light penetration depth and the absence of autofluorescence in biological samples under infrared excitation, these UCNPs have attracted more and more attention on toxin detection and biological labelling. Herein, the fluorescence probe based on UCNPs was developed for quantifying Aflatoxin B₁ (AFB₁) in peanut oil. Based on a specific immunity format, the detection limit for AFB₁ under optimal conditions was obtained as low as 0.2 ng·ml^{- 1}, and in the effective detection range 0.2 to 100 ng·ml^{- 1}, good relationship between fluorescence intensity and AFB₁ concentration was achieved under the linear ratios up to 0.90. Moreover, to check the feasibility of these probes on AFB₁ measurements in peanut oil, recovery tests have been carried out. A good accuracy rating (93.8%) was obtained in this study. Results showed that the nanoparticles can be successfully applied for sensing AFB₁ in peanut oil.

Assessment of Activity of 'Transparent and Clear' and 'Opaque and Highly Coloured' Photocatalytic Samples using a Fluorescent Photocatalytic Activity Indicator Ink, FPaii.

The photocatalytic activity of self-cleaning glass is assessed using a resazurin (Rz) photocatalyst activity indicator ink, i.e. Rz paii, via both the rate of change in the colour of the ink (blue to pink), R(Abs), and the rate of change in the fluorescence intensity, R(Fl), (λ(excitation) = 593 nm; λ(emission) = 639 nm) of the ink. In both cases the kinetics are zero order. Additional work with a range of glass samples of different photocatalytic activity reveal R(Abs) is directly related to R(Fl), thereby showing that the latter, like the former, can be used to provide a measure of the photocatalytic activity of the sample under test. The measured value of R(Fl) is found to be the same for 5 pieces of, otherwise identical, selfcleaning glass with: black, red, blue, yellow and no coloured tape stuck to their backs, which demonstrates that R(Fl) measurements can be used to measure photocatalytic activity under conditions of high colour and opacity under which R(Abs) cannot be measured. The relevance of this novel, fluorescence-based paii to the assessment of the activity of highly coloured, opaque photocatalytic samples, such as paints and tiles, is discussed briefly.

A review of one-step fluorescent cyanoacrylate techniques

A review of recent research in the use of one-step fluorescent cyanoacrylate techniques is presented. Advantages and disadvantages of such techniques in comparison to two-step processes are discussed. Further studies and new experimental data are presented to aid this review: three one-step cyanoacrylate products (Lumicyano, PolyCyano UV and PECA Multiband) containing a fluorescent dye were tested to evaluate their effectiveness in developing latent fingermarks on polyethylene bags by means of a pseudo operational trial. The results were compared to the traditional two-step process of cyanoacrylate fuming followed by staining with ethanol-based basic yellow 40 (BY40). The study was conducted using sequential treatments of an initial fuming cycle, a second cycle and finally BY40 staining. LumicyanoTM and PolyCyano UV performed similarly before BY40 staining, with both providing good contrast and visibility under fluorescence. PECA Multiband, however, did not develop as many fingermarks and proved to be problematic for the fuming cabinet. Subsequent BY40 staining of fingermarks developed by all three one-step processes enabled the visualisation of new fingermarks.

Rapporto tecnico sulla ottimizzazione del processo di biosintesi di una Green Fluorescent Protein ricombinante estratta da A. sulcata

L’espressione di geni eterologhi in Escherichia coli rappresenta uno dei metodi più veloci, semplici ed economici per la produzione di ampie quantità di proteine target. Tuttavia, meccanismi di folding e le modifiche post traduzionali inducono a volte un non corretto ripiegamento delle proteine nella conformazione nativa, con successiva aggregazione in quelli che vengono definiti corpi di inclusione. Nel nostro caso, l’attenzione è stata focalizzata su una Green Fluorescent Protein (GFP) di 228 aa estratta da Anemonia sulcata, contenente un fluoroforo composto da tre amminoacidi Gln63, Tyr64, Gly65 all'interno di una struttura a barile. Il corretto folding della proteina era correlato strettamente alla funzionalità del fluoroforo. Il nostro obiettivo è stato quello, quindi, di ottimizzare il processo di biosintesi della GFP espressa in E. coli, ovviando alla formazione di corpi di inclusione contenenti la proteina (non funzionale), definendo e standardizzando inoltre, le condizioni che consentivano di produrre la più alta percentuale di GFP correttamente ripiegata (in condizioni non denaturanti) e quindi funzionale.