Modified hydrogel matrices in fibre optic sensors

Common problems encountered in clinical sensing are those of non-biocompatibility, and slow response time of the device. The latter, also applying to chemical sensors, is possibly due to a lack of understanding of polymer support or membrane properties and hence failure to optimise membranes chosen for specific sensor applications. Hydrogels can be described as polymers which swell in water. In addition to this, the presence of water in the polymer matrix offers some control of biocompatibility. They thus provide a medium through which rapid transport of a sensed species to an incorporated reagent could occur. This work considers the feasibility of such a system, leading to the design and construction of an optical sensor test bed. The development of suitable membrane systems and of suitable coating techniques in order to apply them to the fibre optics is described. Initial results obtained from hydrogel coatings implied that the refractive index change in the polymer matrix, due to a change in water content with pH is the major factor contributing to the sensor response. However the presence of the colourimetric reagent was also altering the output signal obtained. An analysis of factors contributing to the overall response, such as colour change and membrane composition were made on both the test bed, via optical response, and on whole membranes via measurement of water content change. The investigation of coatings with low equilibrium water contents, of less than 10% was carried out and in fact a clearer signal response from the test bed was noted. Again these membranes were suprisingly responding via refractive index change, with the reagent playing a primary role in obtaining a sensible or non-random response, although not in a colourimetric fashion. A photographic study of these coatings revealed some clues as to the physical nature of these coatings and hence partially explained this phenomenon. A study of the transport properties of the most successful membrane, on a coated wire electrode and also on the fibre optic test bed, in a series of test environments, indicated that the reagent was possibly acting as an ion exchanger and hence having a major influence on transport and therefore sensor characteristics.

An analysis of the effectiveness of a behavioural based safety intervention in a UK paper mill

This research examines a behavioural based safety (BBS) intervention within a paper mill in the South East of England. Further to this intervention two other mills are examined for the purposes of comparison — one an established BBS programme and the other an improving safety management system through management ownership. BBS programmes have become popular within the UK, but most of the research about their efficacy is carried out by the BBS providers themselves. This thesis aims to evaluate a BBS intervention from a standpoint which is not commercially biased in favour of BBS schemes. The aim of a BBS scheme is to either change personnel behaviours or attitudes, which in turn will positively affect the organisation's safety culture. The research framework involved a qualitative methodology in order to examine the effects of the intervention on the paper mill's safety culture. The techniques used were questionnaires and semi structured interviews, in addition to observation and discussions which were possible because of the author's position as participant observer. The results demonstrated a failure to improve any aspect of the mill's safety culture, which worsened following the BBS intervention. Issues such as trust, morale, communication and support of management showed significant signs of negative workforce response. The paper mill where the safety management system approach was utilised demonstrated a significantly improved safety culture and achieved site ownership from middle managers and supervisors. Research has demonstrated that a solid foundation is required prior to successfully implementing a BBS programme. For a programme to work there must be middle management support in addition to senior management commitment. If a trade union actively distances itself from BBS, it is also unlikely to be effective. This thesis proposes that BBS observation programmes are not suitable for the papermaking industry, particularly when staffing levels are low due to challenging economic conditions. Observers are not available when there are high hazard situations and this suggests that BBS implementation is not the correct intervention for the paper industry.

Ethnic conflict and war crimes in the Balkans:the narratives of denial in post-conflict Serbia

In the years following the fall of Slobodan Milo evic, Serbian social, cultural and political responses to the wars of the 1990s have fallen under intense international scrutiny. But is this scrutiny justfied, and how can these responses be better understood? Jelena Obradovic engages with ideas about post-conflict societies, memory, cultural trauma, and national myths of victimhood and justified war to shed light upon Serbian denial and justification of war crimes - for example, Serbia's reluctant cooperation with the International Criminal Tribunal for the former Yugoslavia (ICTY). Rather than treating denial as a failure to come to terms with the past or as resurgent nationalism, Obradovic argues that the justification of atrocities are often the result of a societal need to understand and incorporate violent events within culturally acceptable boundaries.

The development of collaborative skills in young children

This thesis examines young children's early collaborative development when engaged in joint tasks with both a peer and a parent. It begins by examining how the term "collaborative" has been applied and researched in previous literature. As collaboration is found to usually require dialogue, and intersubjectivity is seen as an important component in the construction of both collaboration and dialogue, the ability to construct intersubjectivity is the subject of the rest of the chapter. The chapter concludes by introducing the research questions that underpin the experiments that follow. A number of experiments are then described. Experiments 1 and 2 investigate age differences in interaction styles and the communication strategies used by similar aged dyads. Experiments 3 and 4 investigate differences due to the age of the child and/or the status of the information giver (either parent or child) in the styles of interaction and the communication strategies used by parent and child dyads. Experiment 5 investigates the benefits of collaborating with a parent, and finally, Experiment 6 examines the collaborative ability of pre-schools. The thesis identifies a series of skills required for successful collaboration. These include recognition of a joint goal and the need to suppress individual desires, the ability to structure joint interaction, moving from role-based to a negotiating style, and communicative skills, for example, asking for clarification. Other reasons for children's failure in collaborative tasks involve task-related skills, such as the development of spatial terms, and failure to recognise the need for accuracy. The findings support Vygotsky's theory that when working with an adult, children perform at a higher level than when working with a peer. Evidence was also found of parents scaffolding the interaction for their children. However, further research is necessary to establish that such scaffolding skills affect the child's development of collaborative interactive skills.

A systems and cybernetic perspective on complex problem solving

This thesis is concerned with Organisational Problem Solving. The work reflects the complexities of organisational problem situations and the eclectic approach that has been necessary to gain an understanding of the processes involved. The thesis is structured into three main parts. Part I describes the author's understanding of problems and suitable approaches. Chapter 2 identifies the Transcendental Realist (TR) view of science (Harre 1970, Bhaskar 1975) as the best general framework for identifying suitable approaches to complex organisational problems. Chapter 3 discusses the relationship between Checkland's methodology (1972) and TR. The need to generate iconic (explanatory) models of the problem situation is identified and the ability of viable system modelling to supplement the modelling stage of the methodology is explored in Chapter 4. Chapter 5 builds further on the methodology to produce an original iconic model of the methodological process. The model characterises the mechanisms of organisational problem situations as well as desirable procedural steps. The Weltanschauungen (W's) or "world views" of key actors is recognised as central to the mechanisms involved. Part II describes the experience which prompted the theoretical investigation. Chapter 6 describes the first year of the project. The success of this stage is attributed to the predominance of a single W. Chapter 7 describes the changes in the organisation which made the remaining phase of the project difficult. These difficulties are attributed to a failure to recognise the importance of differing W's. Part III revisits the theoretical and organisational issues. Chapter 8 identifies a range of techniques embodying W's which are compatible with .the framework of Part I and which might usefully supplement it. Chapter 9 characterises possible W's in the sponsoring organisation. Throughout the work, an attempt 1s made to reflect the process as well as the product of the author's leaving.

Priority evaluation in transportation policies and programmes

This work is concerned with the development of techniques for the evaluation of large-scale highway schemes with particular reference to the assessment of their costs and benefits in the context of the current transport planning (T.P.P.) process. It has been carried out in close cooperation with West Midlands County Council, although its application and results are applicable elsewhere. The background to highway evaluation and its development in recent years has been described and the emergence of a number of deficiencies in current planning practise noted. One deficiency in particular stood out, that stemming from inadequate methods of scheme generation and the research has concentrated upon improving this stage of appraisal, to ensure that subsequent stages of design, assessment and implementation are based upon a consistent and responsive foundation. Deficiencies of scheme evaluation were found to stem from inadequate development of appraisal methodologies suffering from difficulties of valuation, measurement and aggregation of the disparate variables that characterise highway evaluation. A failure to respond to local policy priorities was also noted. A 'problem' rather than 'goals' based approach to scheme generation was taken, as it represented the current and foreseeable resource allocation context more realistically. A review of techniques with potential for highway problem based scheme generation, which would work within a series of practical and theoretical constraints were assessed and that of multivariate analysis, and classical factor analysis in particular, was selected, because it offerred considerable application to the difficulties of valuation, measurement and aggregation that existed. Computer programs were written to adapt classical factor analysis to the requirements of T.P.P. highway evaluation, using it to derive a limited number of factors which described the extensive quantity of highway problem data. From this, a series of composite problem scores for 1979 were derived for a case study area of south Birmingham, based upon the factorial solutions, and used to assess highway sites in terms of local policy issues. The methodology was assessed in the light of its ability to describe highway problems in both aggregate and disaggregate terms, to guide scheme design, coordinate with current scheme evaluation methods, and in general to improve upon current appraisal. Analysis of the results was both in subjective, 'common-sense' terms and using statistical methods to assess the changes in problem definition, distribution and priorities that emerged. Overall, the technique was found to improve upon current scheme generation methods in all respects and in particular in overcoming the problems of valuation, measurement and aggregation without recourse to unsubstantiated and questionable assumptions. A number of deficiencies which remained have been outlined and a series of research priorities described which need to be reviewed in the light of current and future evaluation needs.

Design of an expandable manufacturing simulator through the application of object-oriented principles

In analysing manufacturing systems, for either design or operational reasons, failure to account for the potentially significant dynamics could produce invalid results. There are many analysis techniques that can be used, however, simulation is unique in its ability to assess detailed, dynamic behaviour. The use of simulation to analyse manufacturing systems would therefore seem appropriate if not essential. Many simulation software products are available but their ease of use and scope of application vary greatly. This is illustrated at one extreme by simulators which offer rapid but limited application whilst at the other simulation languages which are extremely flexible but tedious to code. Given that a typical manufacturing engineer does not posses in depth programming and simulation skills then the use of simulators over simulation languages would seem a more appropriate choice. Whilst simulators offer ease of use their limited functionality may preclude their use in many applications. The construction of current simulators makes it difficult to amend or extend the functionality of the system to meet new challenges. Some simulators could even become obsolete as users, demand modelling functionality that reflects the latest manufacturing system design and operation concepts. This thesis examines the deficiencies in current simulation tools and considers whether they can be overcome by the application of object-oriented principles. Object-oriented techniques have gained in popularity in recent years and are seen as having the potential to overcome any of the problems traditionally associated with software construction. There are a number of key concepts that are exploited in the work described in this thesis: the use of object-oriented techniques to act as a framework for abstracting engineering concepts into a simulation tool and the ability to reuse and extend object-oriented software. It is argued that current object-oriented simulation tools are deficient and that in designing such tools, object -oriented techniques should be used not just for the creation of individual simulation objects but for the creation of the complete software. This results in the ability to construct an easy to use simulator that is not limited by its initial functionality. The thesis presents the design of an object-oriented data driven simulator which can be freely extended. Discussion and work is focused on discrete parts manufacture. The system developed retains the ease of use typical of data driven simulators. Whilst removing any limitation on its potential range of applications. Reference is given to additions made to the simulator by other developers not involved in the original software development. Particular emphasis is put on the requirements of the manufacturing engineer and the need for Ihe engineer to carrv out dynamic evaluations.

Mechanism of uptake of the catecholic (7)-α-formamido cephalosporin BRL 41897A by klebsiella pneumoniae

The catecholic cephalosporin BRL 41897 A is resistant to β-lactamases and is taken up by bacteria via the iron transport system. The uptake of this antibiotic in E.coli uses the Fiu and Cir outer membrane proteins, whereas in P. aerugtnosa it enters via the pyochelin transport system. In this thesis mutants of K. pneumoniae resistant to BRL 41897A were isolated using TnphoA mutagenesis and used to study the mechanism of uptake of BRL 41897A by K. pneumoniae. The activity of BRL 41897A towards the parent strain (M10) was increased in iron depleted media, whereas no significant differences in the resistant (KSL) mutants were observed. Three mutants (KSL19, KSL38and KSL59) produced decreased amounts of certain iron-regulated outer membrane proteins. The uptake of 55Fe-BRL 41897A by M10 in iron-deficient medium was higher than in iron-rich medium. This result indicated the involvement of an iron transport system in the uptake of BRL 41897A by K. pneumoniae. Uptake by the KSL mutants in iron-deficient culture was higher than that by M10. This result, supported by analysis of outer membrane and periplasmic proteins of the KSL mutants, indicates that loss of one outer membrane protein can be compensated by over expression of other outer membrane and/or periplasmic proteins. However, the increased uptake of BRL 41897A by the KSL mutants did not reflect increased activity towards these strains, indicating that there are defects in the transport of BRL 41897A resulting in failure to reach the penicillin binding protein target sites in the cytoplasmic membrane. Southern blotting of chromosomal digests and sequencing in one mutant (KSL19) showed that only one copy of TnphoA was inserted into its chromosome. A putative TnphoA inserted gene in KSL19, designated kslA, carrying a signal sequence was identified. Transformation of a fragment containing the kslA gene into KSL19 cells restored the sensitivity to BRL 41897A to that of the parent strain. Data base peptide sequence searches revealed that the kslA gene in the KSL19 has some amino acid homology with the E. coli ExbD protein, which is involved in stabilisation of the TonB protein. 

Today's pupils tomorrow's engineers! Pedagogy and policy:a UK perspective

Purpose – This paper aims to provide a critical analysis of UK Government policy in respect of recent moves to attract young people into engineering. Drawing together UK and EU policy literature, the paper considers why young people fail to look at engineering positively. Design/methodology/approach – Drawing together UK policy, practitioner and academic-related literature the paper critically considers the various factors influencing young people's decision-making processes in respect of entering the engineering profession. A conceptual framework providing a diagrammatic representation of the “push” and “pull” factors impacting young people at pre-university level is given. Findings – The discussion argues that higher education in general has a responsibility to assist young people overcome negative stereotypical views in respect of engineering education. Universities are in the business of building human capability ethically and sustainably. As such they hold a duty of care towards the next generation. From an engineering education perspective, the major challenge is to present a relevant and sustainable learning experience that will equip students with the necessary skills and competencies for a lifelong career in engineering. This may be achieved by promoting transferable skills and competencies or by the introduction of a capabilities-driven curriculum which brings together generic and engineering skills and abilities. Social implications – In identifying the push/pull factors impacting young people's decisions to study engineering, this paper considers why, at a time of global recession, young people should select to study the required subjects of mathematics, science and technology necessary to study for a degree in engineering. The paper identifies the long-term social benefits of increasing the number of young people studying engineering. Originality/value – In bringing together pedagogy and policy within an engineering framework, the paper adds to current debates in engineering education providing a distinctive look at what seems to be a recurring problem – the failure to attract young people into engineering.

Optimization of a 42.7 Gb/s wavelength tunable RZ transmitter using a linear spectrogram technique

The optimization of a wavelength tunable RZ transmitter, consisting of an electro-absorption modulator and a SG DBR tunable laser, is carried out using a linear spectrogram based characterization and leads to 1500 km transmission at 42.7 Gb/s independent of the operating wavelength. We demonstrate that, to ensure optimum and consistent transmission performance over a portion of the C-band, the RF drive and bias conditions of the EAM must be varied at each wavelength. The sign and magnitude of the pulse chirp (characterized using the linear spectrographic technique) is therefore tailored to suit the dispersion map of the transmission link. Results achieved show that by optimizing the drive and DC bias applied to the EAM, consistent transmission performance can be achieved over a wide wavelength range. Failure to optimize the EAM drive conditions at each wavelength can lead to serious degradation in system performance.

Recent developments in information retrieval:preface

This paper summarizes the scientific work presented at the 32nd European Conference on Information Retrieval. It demonstrates that information retrieval (IR) as a research area continues to thrive with progress being made in three complementary sub-fields, namely IR theory and formal methods together with indexing and query representation issues, furthermore Web IR as a primary application area and finally research into evaluation methods and metrics. It is the combination of these areas that gives IR its solid scientific foundations. The paper also illustrates that significant progress has been made in other areas of IR. The keynote speakers addressed three such subject fields, social search engines using personalization and recommendation technologies, the renewed interest in applying natural language processing to IR, and multimedia IR as another fast-growing area.

Monetary variability and monetary variables in the Franc zone

Failure to detect or account for structural changes in economic modelling can lead to misleading policy inferences, which can be perilous, especially for the more fragile economies of developing countries. Using three potential monetary policy instruments (Money Base, M0, and Reserve Money) for 13 member-states of the CFA Franc zone over the period 1989:11-2002:09, we investigate the magnitude of information extracted by employing data-driven techniques when analyzing breaks in time-series, rather than the simplifying practice of imposing policy implementation dates as break dates. The paper also tests Granger's (1980) aggregation theory and highlights some policy implications of the results.

Professional standards research:job satisfaction and innovation

Job satisfaction is a significant predictor of organisational innovation – especially where employees (including shop-floor workers) experience variety in their jobs and work in a single-status environment. The relationship between job satisfaction and performance has long intrigued work psychologists. The idea that "happy workers are productive workers" underpins many theories of performance, leadership, reward and job design. But contrary to popular belief, the relationship between job satisfaction and performance at individual level has been shown to be relatively weak. Research investigating the link between job satisfaction and creativity (the antecedent to innovation) shows that job dissatisfaction promotes creative outcomes. The logic is that those who are dissatisfied (and have decided to stay with the organisation) are determined to change things and have little to lose in doing so (see JM George & J Zhou, 2002). We were therefore surprised to find in the course of our own research into managerial practices and employee attitudes in manufacturing organisations that job satisfaction was a highly significant predictor of product and technological innovation. These results held even though the research was conducted longitudinally, over two years, while controlling for prior innovation. In other words, job satisfaction was a stronger predictor of innovation than any pre-existing orientation organisations had towards working innovatively. Using prior innovation as a control variable, as well as a longitudinal research design, strengthened our case against the argument that people are satisfied because they belong to a highly innovative organisation. We found that the relationship between job satisfaction and innovation was stronger still where organisations showed that they were committed to promoting job variety, especially at shop-floor level. We developed precise instruments to measure innovation, taking into account the magnitude of the innovation both in terms of the number of people involved in its implementation, and how new and different it was. Using this instrument, we are able to give each organisation in our sample a "score" from one to seven for innovation in areas ranging from administration to production technology. We found that much innovation is incremental, involving relatively minor improvements, rather than major change. To achieve sustained innovation, organisations have to draw on the skills and knowledge of employees at all levels. We also measured job satisfaction at organisational level, constructing a mean "job satisfaction" score for all organisations in our sample, and drawing only on those companies whose employees tended to respond in a similar manner to the questions they were asked. We argue that where most of the workforce experience job satisfaction, employees are more likely to collaborate, to share ideas and aim for high standards because people are keen to sustain their positive feelings. Job variety and single-status arrangements further strengthen the relationship between satisfaction and performance. This makes sense; where employees experience variety, they are exposed to new and different ideas and, provided they feel positive about their jobs, are likely to be willing to try to apply these ideas to improve their jobs. Similarly, staff working in single-status environments where hierarchical barriers are reduced are likely to feel trusted and valued by management and there is evidence (see G Jones & J George, 1998) that people work collaboratively and constructively with those they trust. Our study suggests that there is a strong business case for promoting employee job satisfaction. Managers and HR practitioners need to ensure their strategies and practices support and sustain job satisfaction among their workforces to encourage constructive, collaborative and creative working. It is more important than ever for organisations to respond rapidly to demands of the external environment. This study shows the positive association between organisational-level job satisfaction and innovation. So if a happy workforce is the key to unlocking innovation and organisations want to thrive in the global economy, it is vital that managers and HR practitioners pay close attention to employee perceptions of the work environment. In a world where the most innovative survive it could make all the difference.

Introduction : the role of quality, production and technological innovation in improving competitive performance

Quality, production and technological innovation management rank among the most important matters of concern to modern manufacturing organisations. They can provide companies with the decisive means of gaining a competitive advantage, especially within industries where there is an increasing similarity in product design and manufacturing processes. The papers in this special issue of International Journal of Technology Management have all been selected as examples of how aspects of quality, production and technological innovation can help to improve competitive performance. Most are based on presentations made at the UK Operations Management Association's Sixth International Conference held at Aston University at which the theme was 'Getting Ahead Through Technology and People'. At the conference itself over 80 papers were presented by authors from 15 countries around the world. Among the many topics addressed within the conference theme, technological innovation, quality and production management emerged as attracting the greatest concern and interest of delegates, particularly those from industry. For any new initiative to be implemented successfully, it should be led from the top of the organization. Achieving the desired level of commitment from top management can, however, be a difficulty. In the first paper of this issue, Mackness investigates this question by explaining how systems thinking can help. In the systems approach, properties such as 'emergence', 'hierarchy', 'commnication' and 'control' are used to assist top managers in preparing for change. Mackness's paper is then complemented by Iijima and Hasegawa's contribution in which they investigate the development of Quality Information Management (QIM) in Japan. They present the idea of a Design Review and demonstrate how it can be used to trace and reduce quality-related losses. The next paper on the subject of quality is by Whittle and colleagues. It relates to total quality and the process of culture change within organisations. Using the findings of investigations carried out in a number of case study companies, they describe four generic models which have been identified as characterising methods of implementing total quality within existing organisation cultures. Boaden and Dale's paper also relates to the management of quality, but looks specifically at the construction industry where it has been found there is still some confusion over the role of Quality Assurance (QA) and Total Quality Management (TQM). They describe the results of a questionnaire survey of forty companies in the industry and compare them to similar work carried out in other industries. Szakonyi's contribution then completes this group of papers which all relate specifically to the question of quality. His concern is with the two ways in which R&D or engineering managers can work on improving quality. The first is by improving it in the laboratory, while the second is by working with other functions to improve quality in the company. The next group of papers in this issue all address aspects of production management. Umeda's paper proposes a new manufacturing-oriented simulation package for production management which provides important information for both design and operation of manufacturing systems. A simulation for production strategy in a Computer Integrated Manufacturing (CIM) environment is also discussed. This paper is then followed by a contribution by Tanaka and colleagues in which they consider loading schedules for manufacturing orders in a Material Requirements Planning (MRP) environment. They compare mathematical programming with a knowledge-based approach, and comment on their relative effectiveness for different practical situations. Engstrom and Medbo's paper then looks at a particular aspect of production system design, namely the question of devising group working arrangements for assembly with new product structures. Using the case of a Swedish vehicle assembly plant where long cycle assembly work has been adopted, they advocate the use of a generally applicable product structure which can be adapted to suit individual local conditions. In the last paper of this particular group, Tay considers how automation has affected the production efficiency in Singapore. Using data from ten major industries he identifies several factors which are positively correlated with efficiency, with capital intensity being of greatest interest to policy makers. The two following papers examine the case of electronic data interchange (EDI) as a means of improving the efficiency and quality of trading relationships. Banerjee and Banerjee consider a particular approach to material provisioning for production systems using orderless inventory replenishment. Using the example of a single supplier and multiple buyers they develop an analytical model which is applicable for the exchange of information between trading partners using EDI. They conclude that EDI-based inventory control can be attractive from economic as well as other standpoints and that the approach is consistent with and can be instrumental in moving towards just-in-time (JIT) inventory management. Slacker's complementary viewpoint on EDI is from the perspective of the quality relation-ship between the customer and supplier. Based on the experience of Lucas, a supplier within the automotive industry, he concludes that both banks and trading companies must take responsibility for the development of payment mechanisms which satisfy the requirements of quality trading. The three final papers of this issue relate to technological innovation and are all country based. Berman and Khalil report on a survey of US technological effectiveness in the global economy. The importance of education is supported in their conclusions, although it remains unclear to what extent the US government can play a wider role in promoting technological innovation and new industries. The role of technology in national development is taken up by Martinsons and Valdemars who examine the case of the former Soviet Union. The failure to successfully infuse technology into Soviet enterprises is seen as a factor in that country's demise, and it is anticipated that the newly liberalised economies will be able to encourage greater technological creativity. This point is then taken up in Perminov's concluding paper which looks in detail at Russia. Here a similar analysis is made of the concluding paper which looks in detail at Russia. Here a similar analysis is made of the Soviet Union's technological decline, but a development strategy is also presented within the context of the change from a centralised to a free market economy. The papers included in this special issue of the International Journal of Technology Management each represent a unique and particular contribution to their own specific area of concern. Together, however, they also argue or demonstrate the general improvements in competitive performance that can be achieved through the application of modern principles and practice to the management of quality, production and technological innovation.

Diesseits und jenseits der Oder:Judith Hermanns literarische Auseinandersetzung mit Theodor Fontane in Sommerhaus, später

Judith Hermann's works have attracted considerable criticism for their supposedly slight portrayal of passively drifting characters and for their alleged failure to engage with the socio-political realities of contemporary life in the Berlin Republic. Only very recently have scholars paid attention to the hidden concern with memory expressed in her books, and have set out to examine their intertextual depth. This paper explores these previously neglected historical references in Summerhouse, later and analyses the book's intricate intertextual allusions with specific reference to Theodor Fontane's works. It examines how the tentative existence, which Hermann's characters experience, is the product of a hesitant and fruitless confrontation with questions of German history and nationhood. Using pervasive water imagery, Hermann shows present-day Germany as a continually contested territory with a fluid identity shaped by an abundance of conflicting narratives. In this context, the allusions to Fontane as a representative of the Wilhelminian period serve as references to a continuing German tradition of repression and marginalisation. At the same time, Hermann recognises Fontane's ambivalent political stance combining elements of social criticism with a general endorsement of social order. Ultimately, the seemingly indifferent attitude of Hermann's characters and the elegiac style used to portray them, emerge as a distancing mechanism that functions as a postmodern variant of Fontane's irony and is shaped by a similar sense of skepticism towards developments in German society and national history. © 2012 Springer Science+Business Media B.V.