Development of a colorimetric assay for heparanase activity suitable for kinetic analysis and inhibitor screening

The role that heparanase plays during metastasis and angiogenesis in tumors makes it an attractive target for cancer therapeutics. Despite this enzyme’s significance, most of the assays developed to measure its activity are complex. Moreover, they usually rely on labeling variable preparations of the natural substrate heparan sulfate, making comparisons across studies precarious. To overcome these problems, we have developed a convenient assay based on the cleavage of the synthetic heparin oligosaccharide fondaparinux. The assay measures the appearance of the disaccharide product of heparanase-catalyzed fondaparinux cleavage colorimetrically using the tetrazolium salt WST-1. Because this assay has a homogeneous substrate with a single point of cleavage, the kinetics of the enzyme can be reliably characterized, giving a Km of 46 μM and a kcat of 3.5 s−1 with fondaparinux as substrate. The inhibition of heparanase by the published inhibitor, PI-88, was also studied, and a Ki of 7.9 nM was determined. The simplicity and robustness of this method, should, not only greatly assist routine assay of heparanase activity but also could be adapted for high-throughput screening of compound libraries, with the data generated being directly comparable across studies.

An indexing model for stormwater quality in the Gold Coast

In the era of climate change sustainable urban development and in particular provision of sustainable urban infrastructure has become a key concept in dealing with environmental challenges. This paper discusses issues affecting stormwater quality and introduces a new indexing model that is to be used in evaluation of the stormwater quality in urban areas. The model has recently been developed and will be tested in a number of pilot projects in the Gold Coast, one of the fastest growing and environmentally challenged cities of Australia.

Science education policy-making : eleven emerging issues

The Perth Declaration on Science and Technology Education of 2007 expresses strong concern about the state of science and technology education worldwide and calls on governments to respond to a number of suggestions for establishing the structural conditions for their improved practice. The quality of school education in science and technology has never before been of such critical importance to governments. There are three imperatives for its critical importance. The first relates to the traditional role of science in schooling, namely the identification, motivation and initial preparation of those students who will go on to further studies for careers in all those professional fi elds that directly involve science and technology. A suffi cient supply of these professionals is vital to the economy of all countries and to the health of their citizens. In the 21st century they are recognised everywhere as key players in ensuring that industrial and economic development occurs in a socially and environmentally sustainable way. In many countries this supply is now falling seriously short and urgently needs to be addressed. The second imperative is that sustainable technological development and many other possible societal applications of science require the support of scientifically and technologically informed citizens. Without the support and understanding of citizens, technological development can all too easily serve short term and sectional interests. The longer term progress of the whole society is overlooked, citizens will be confused about what should, and what should not be supported, and reactive and the environment will continue to be destroyed rather than sustained. Sustainable development, and the potential that science and technology increasingly offers, involves societies in ways that can often interact strongly, with traditional values, and hence, making decisions about them involve major moral decisions. All students need to be prepared through their science and technology education to be able to participate actively as persons and as responsible citizens in these essential and exciting possibilities. This goal is far from being generally achieved at present, but pathways to it are now more clearly understood. The third imperative derives from the changes that are resulting from the application of digital technologies that are the most rapid, the most widespread, and probably the most pervasive influence that science has ever had on human society. We all, wherever we live, are part of a global communication society. Information exchange and access to it that have been hitherto the realm of the few, are now literally in the hands of individuals. This is leading to profound changes in the World of Work and in what is known as the Knowledge Society. Schooling is now being challenged to contribute to the development in students of an active repertoire of generic and subject-based competencies. This contrasts very strongly with existing priorities, in subjects like the sciences that have seen the size of a student’s a store of established knowledge as the key measure of success. Science and technology education needs to be a key component in developing these competencies. When you add to these imperatives, the possibility that a more effective education in science and technology will enable more and more citizens to delight in, and feel a share in the great human enterprise we call Science, the case for new policy decisions is compellingly urgent. What follows are the recommendations (and some supplementary notes) for policy makers to consider about more operational aspects for improving science and technology education. They are listed under headings that point to the issues within each of these aspects. In the full document, a background is provided to each set of issues, including the commonly current state of science and technology education. Associated with each recommendation for consideration are the positive Prospects that could follow from such decision making, and the necessary Prerequisites, if such bold policy decisions are to fl ow, as intended, into practice in science and technology classrooms.

A comparative study : regulatory requirements on subdivisions for increasing passive cooling

A major project in the Sustainable Built Assets core area is the Sustainable Sub-divisions – Ventilation Project that is the second stage of a planned series of research projects focusing on sustainable sub-divisions. The initial project, Sustainable Sub-divisions: Energy focused on energy efficiency and examined the link between dwelling energy efficiency and sub-divisional layout. In addition, the potential for on site electricity generation, especially in medium and high-density developments, was also examined. That project recommended that an existing lot-rating methodology be adapted for use in SEQ through the inclusion of sub divisional appropriate ventilation data. Acquiring that data is the object of this project. The Sustainable Sub-divisions; Ventilation Project will produce a series of reports. The first report (Report 2002-077-B-01) summarised the results from an industry workshop and interviews that were conducted to ascertain the current attitudes and methodologies used in contemporary sub-division design in South East Queensland. The second report (Report 2002-077-B-02) described how the project is being delivered as outlined in the Project Agreement. It included the selection of the case study dwellings and monitoring equipment and data management process. This third report (Report 2002-077-B-03) provides an analysis and review of the approaches recommended by leading experts, government bodies and professional organizations throughout Australia that aim to increase the potential for passive cooling and heating at the subdivision stage. This data will inform issues discussed on the development of the enhanced lot-rating methodology in other reports of this series. The final report, due in June 2007, will detail the analysis of data for winter 2006 and summer 2007, leading to the development and delivery of the enhanced lot-rating methodology.

Communicating ecologically positive development

It is difficult to present a paradigm shift from resource efficient to ecologically sustainable design, when many students have not yet thought about what sustainability is, let alone what it implies for the design of the built environment ‘Positive Development’ requires students to think beyond green building to something that does not yet exist. The concept of ecologically positive development suggests a product, building, system or urban area that leaves the ecological base and public estate better off than if no development had occurred. For some years now, I have experimented with communicating this paradigm shift in design to students and professionals ‐ with mixed results. This paper discusses some of the challenges, failures and successes in shifting design studio work from environmentally‐sensitive to eco-positive. The framework underlying this exploration is action research. Conclusions about the success of the strategies used for overcoming perceptual barriers to new typologies of architecture are drawn from recent student feedback. The talk will show examples of student projects that attempt eco-positive development projects.

Using digital storytelling to capture responses to the Apology

This article discusses a pilot project that adapted the methods of digital storytelling and oral history to capture a range of personal responses to the official Apology to Australia’s Indigenous Peoples delivered by Prime Minister Kevin Rudd on 13 February 2008. The project was an initiative of State Library of Queensland and resulted in a small collection of multimedia stories, incorporating a variety of personal and political perspectives. The article describes how the traditional digital storytelling workshop method was adapted for use in the project, and then proceeds to reflect on the outcomes and continuing life of the project. The article concludes by suggesting that aspects of the resultant model might be applied to other projects carried out by cultural institutions and community-based media organizations.

Cases from the technology disciplines

This document is a collection of ‘cases’ adapted from interviews with supervisors of higher degree research students from the technology disciplines. The supervisors come from a wide range of sub disciplines and represent many levels of experience. We follow in this document Hammond and Ryland’s (2009)2 suggested ranking of supervision experience:  No completions – No experience or new supervisors, with no doctoral completions as principal supervisor  Experienced – 1 to 5 doctoral completions as principal supervisor  Very experienced – over 6 doctoral completions as principal supervisor The cases focus attention on thinking about supervision as a teaching and learning practice; a dimension of higher degree research supervision that is increasingly being recognized as important. They are offered as prompts for individuals and groups of supervisors in thinking about their supervision as a teaching and learning practice.

Ipswich stories : using digital storytelling to research intergenerational sharing of heritage, history, place, identity and community connection : a pilot study

Co-creative media production practices offer important new modes and opportunities for social participation and engagement. In mid-2009 Institute for Creative Industries and Innovation researchers at QUT adapted a specific model of co-creative media production, known as ‘digital storytelling’ and piloted it as an action research platform for facilitating and researching knowledge production based on intergenerational dialogue and exchange. Nine stories were produced and important insights were generated into this particular use of digital storytelling, as well as the impact of institutional constraints and opportunities on the possibilities and outcomes co-creative media practices and processes.

Assessing the energy efficiency of gear oils via the FZG test machine

Energy efficient lubricants are becoming increasingly popular. This is due to a global increase in environmental awareness combined with the potential of reducing operating costs. A new test method of evaluating the energy efficiency of gear oils has been described in this report. The method involves measuring the power required by an FZG test rig to run while using a particular test lubricant. For each oil that was being evaluated, the rig was run for 10 minutes at a load stage of 10. Six extreme pressure (EP) industrial gear oils of mineral base were tested. The difference in power requirements between the best and the worst performing oils was 2.77 and 3.24 kW, respectively. This equates to a 14.6% reduction in power, a significant amount if considered in relation to a high powered industrial machine. The oils of superior performance were noticed to run at reduced temperatures. They were also more expensive than the other products of lesser performance.

Velocity and Concentration field of discharge from a boat propeller

Two-stroke outboard boat engines using total loss lubrication deposit a significant proportion of their lubricant and fuel directly into the water. The purpose of this work is to document the velocity and concentration field characteristics of a submerged swirling water jet emanating from a propeller in order to provide information on its fundamental characteristics. Measurements of the velocity and concentration field were performed in a turbulent jet generated by a model boat propeller (0.02 m diameter) operating at 1500 rpm and 3000 rpm. The measurements were carried out in the Zone of Established Flow up to 50 propeller diameters downstream of the propeller. Both the mean axial velocity profile and the mean concentration profile showed self-similarity. Further, the stand deviation growth curve was linear. The effects of propeller speed and dye release location were also investigated.

Measuring quality : how does this improve construction performance?

The paper charts the history and development of the Hong Kong Housing Department (HKHD) Performance Assessment Scoring System (PASS) from 1990 to the present day and examines its effect on facilitating change to the quality of construction work of building contractors engaged in the production of public sector housing projects Hong Kong. The paper builds partly on empirical research carried out by the author as part of a doctoral thesis from 2000 to 2005, on experiential knowledge and also on some relevant case studies. The outcomes from this earlier research and validation of PASS based on results derived from the system since the research was originally undertaken are of benefit to practitioners and academics working and studying in the areas of performance assessment and organisational culture and change. The conclusions presented in the paper further underpin the connection established in previous research between strong organisational culture and project and corporate success. Organisational culture was measured using a survey instrument originally developed by Denison and Neale (1994), adapted for the environment of the study, and corporate success was measured by the PASS system mentioned above. The major results of the original study indicate that there is significant linkage between strong organisational cultures and business success and the detailed findings were that, (1) strong organisational culture was positively associated a high level of company effectiveness, (2) a high level of company effectiveness was positively associated with the cultural traits of ‘consistency’, ‘adaptability’ and ‘mission’, and (3) a high level of company effectiveness was positively associated with the combined cultural traits represented by the dimensions of ‘external focus’ and ‘stable culture’. Several opportunities to take forward this research have been identified, including extending the study to other countries and also longitudinally re-evaluating some of the original case studies to ascertain how organisational cultures have changed or further developed in relation to the changing construction climate in Hong Kong.

Biotribological assessment for artificial synovial joints : the role of boundary lubrication

Biotribology, the study of lubrication, wear and friction within the body, has become a topic of high importance in recent times as we continue to encounter debilitating diseases and trauma that destroy function of the joints. A highly successful surgical procedure to replace the joint with an artificial equivalent alleviates dysfunction and pain. However, the wear of the bearing surfaces in prosthetic joints is a significant clinical problem and more patients are surviving longer than the life expectancy of the joint replacement. Revision surgery is associated with increased morbidity and mortality and has a far less successful outcome than primary joint replacement. As such, it is essential to ensure that everything possible is done to limit the rate of revision surgery. Past experience indicates that the survival rate of the implant will be influenced by many parameters, of primary importance, the material properties of the implant, the composition of the synovial fluid and the method of lubrication. In prosthetic joints, effective boundary lubrication is known to take place. The interaction of the boundary lubricant and the bearing material is of utmost importance. The identity of the vital active ingredient within synovial fluid (SF) to which we owe the near frictionless performance of our articulating joints has been the quest of researchers for many years. Once identified, tribo tests can determine what materials and more importantly what surfaces this fraction of SF can function most optimally with. Surface-Active Phospholipids (SAPL) have been implicated as the body’s natural load bearing lubricant. Studies in this thesis are the first to fully characterise the adsorbed SAPL detected on the surface of retrieved prostheses and the first to verify the presence of SAPL on knee prostheses. Rinsings from the bearing surfaces of both hip and knee prostheses removed from revision operations were analysed using High Performance Liquid Chromatography (HPLC) to determine the presence and profile of SAPL. Several common prosthetic materials along with a novel biomaterial were investigated to determine their tribological interaction with various SAPLs. A pin-on-flat tribometer was used to make comparative friction measurements between the various tribo-pairs. A novel material, Pyrolytic Carbon (PyC) was screened as a potential candidate as a load bearing prosthetic material. Friction measurements were also performed on explanted prostheses. SAPL was detected on all retrieved implant bearing surfaces. As a result of the study eight different species of phosphatidylcholines were identified. The relative concentrations of each species were also determined indicating that the unsaturated species are dominant. Initial tribo tests employed a saturated phosphatidylcholine (SPC) and the subsequent tests adopted the addition of the newly identified major constituents of SAPL, unsaturated phosphatidylcholine (USPC), as the test lubricant. All tribo tests showed a dramatic reduction in friction when synthetic SAPL was used as the lubricant under boundary lubrication conditions. Some tribopairs showed more of an affinity to SAPL than others. PyC performed superior to the other prosthetic materials. Friction measurements with explanted prostheses verified the presence and performance of SAPL. SAPL, in particular phosphatidylcholine, plays an essential role in the lubrication of prosthetic joints. Of particular interest was the ability of SAPLs to reduce friction and ultimately wear of the bearing materials. The identification and knowledge of the lubricating constituents of SF is invaluable for not only the future development of artificial joints but also in developing effective cures for several disease processes where lubrication may play a role. The tribological interaction of the various tribo-pairs and SAPL is extremely favourable in the context of reducing friction at the bearing interface. PyC is highly recommended as a future candidate material for use in load bearing prosthetic joints considering its impressive tribological performance.

An extended CDIO syllabus framework with preparatory engineering proficiencies

The CDIO Initiative has been globally recognised as an enabler for engineering education reform. With the CDIO process, the CDIO Standards and the CDIO Syllabus, many scholarly contributions have been made around cultural change, curriculum reform and learning environments. In the Australasian region, reform is gaining significant momentum within the engineering education community, the profession, and higher education institutions. This paper presents the CDIO Syllabus cast into the Australian context by mapping it to the Engineers Australia Graduate Attributes, the Washington Accord Graduate Attributes and the Queensland University of Technology Graduate Capabilities. Furthermore, in recognition that many secondary schools and technical training institutions offer introductory engineering technology subjects, this paper presents an extended self-rating framework suited for recognising developing levels of proficiency at a preparatory level. The framework is consistent with conventional application to undergraduate programs and professional practice, but adapted for the preparatory context. As with the original CDIO framework with proficiency levels, this extended framework is informed by Bloom’s Educational Objectives. A proficiency evaluation of Queensland Study Authority’s Engineering Technology senior syllabus is demonstrated indicating proficiency levels embedded within this secondary school subject within a preparatory scope. Through this extended CDIO framework, students and faculty have greater awareness and access to tools to promote (i) student engagement in their own graduate capability development, (ii) faculty engagement in course and program design, through greater transparency and utility of the continuum of graduate capability development with associate levels of proficiency, and the context in which they exist in terms of pre-tertiary engineering studies; and (iii) course maintenance and quality audit methodology for the purpose of continuous improvement processes and program accreditation.

A collaborative approach to reading workshop in the middle years

Reflection Questions • How does the collaborative reading workshop approach engage students in higher order thinking and deep engagement with text? • How does the collaborative reading workshop approach support students to be active citizens and critically literate? • How does the interaction and collaborative thinking in this approach contribute to the students’ intellectual engagement and the teacher’s pedagogical rigor? • How could this approach be implemented or adapted at your school?

Measuring factors that influence the utilisation of preventive care services provided by general practitioners in Australia

Background: Relatively little research attention has been given to the development of standardised and psychometrically sound scales for measuring influences relevant to the utilisation of health services. This study aims to describe the development, validation and internal reliability of some existing and new scales to measure factors that are likely to influence utilisation of preventive care services provided by general practitioners in Australia.----- Methods: Relevant domains of influence were first identified from a literature review and formative research. Items were then generated by using and adapting previously developed scales and published findings from these. The new items and scales were pre-tested and qualitative feedback was obtained from a convenience sample of citizens from the community and a panel of experts. Principal Components Analyses (PCA) and internal reliability testing (Cronbach's alpha) were then conducted for all of the newly adapted or developed scales utilising data collected from a self-administered mailed survey sent to a randomly selected population-based sample of 381 individuals (response rate 65.6 per cent).----- Results: The PCA identified five scales with acceptable levels of internal consistency were: (1) social support (ten items), alpha 0.86; (2) perceived interpersonal care (five items), alpha 0.87, (3) concerns about availability of health care and accessibility to health care (eight items), alpha 0.80, (4) value of good health (five items), alpha 0.79, and (5) attitudes towards health care (three items), alpha 0.75.----- Conclusion The five scales are suitable for further development and more widespread use in research aimed at understanding the determinants of preventive health services utilisation among adults in the general population.