Precipitation hardening of Cu-Fe-Cr alloys - Part II - Microstructural characterisation

This research is part of a project whose scope was to investigate the engineering properties of new non-commercial alloy formulations based on the Cu rich corner of the Cu-Fe-Cr ternary system with the primary aim of exploring the development of a new cost-effective high-strength, high-conductivity copper alloy. Promising properties have been measured for the following alloys: Cu-0.7wt%Cr-0.3wt%Fe and Cu-0.7wt%Cr-2.0wt%Fe. This paper reports on the microstructural characterisation of these alloys and discusses the mechanical and electrical properties of these alloys in terms of their microstructure, particularly the formation of precipitates. These alloys have evinced properties that warrant further investigation. Cost modelling has shown that Cu-0.7wt%Cr-0.3wt%Fe is approximately 25% cheaper to produce than commercial Cu-1%Cr. It has also been shown to be more cost efficient on a yield stress and % IACS per dollar basis. The reason for the cost saving is that the Cu-0.7%Cr-0.3%Fe alloy can be made with low carbon ferro-chrome additions as the source of chromium rather than the more expensive Cu-Cr master-alloy. For applications in which cost is one of the primary materials selection criteria, it is envisaged that there would be numerous applications in both cast and wrought form, where the Cu-0.7%Cr-0.3%Fe alloy would be more suitable than Cu-1%Cr. (C) 2001 Kluwer Academic Publishers.

Management of orbitozygomatic fractures

Background: Management of orbitozygomatic fractures forms part of the scope of practice of many oral and maxillofacial Surgeons. As aspects of management vary among surgeons who treat such injuries, this confidential study was undertaken to examine some of the protocols of Australian and New Zealand oral and maxillofacial surgeons. Results: Eighty-one per cent of the respondents treated orbitozygomatic fractures and on average. each treated approximately 24 cases per year. Also, about one in five cases required orbital floor exploration. Further, the preferred imaging baseline was computed tomography plus plain X-rays. while the preferred implant materials for orbital floor reconstruction were autologous bone and resorbable membrane. The incidence of postoperative retrobulbar haemorrhage was estimated at approximately 1:1000. Conclusion: Most oral and maxillofacial surgeons treat orbitozygomatic injuries as part of their surgical scope.

Existence of a semicontinuous or continuous utility function: a unified approach and an elementary proof

In this paper, we present a new unified approach and an elementary proof of a very general theorem on the existence of a semicontinuous or continuous utility function representing a preference relation. A simple and interesting new proof of the famous Debreu Gap Lemma is given. In addition, we prove a new Gap Lemma for the rational numbers and derive some consequences. We also prove a theorem which characterizes the existence of upper semicontinuous utility functions on a preordered topological space which need not be second countable. This is a generalization of the classical theorem of Rader which only gives sufficient conditions for the existence of an upper semicontinuous utility function for second countable topological spaces. (C) 2002 Elsevier Science B.V. All rights reserved.

A review of guidelines and standards for telemedicine

We conducted a review to establish the range and scope of current telemedicine guidelines and standards. Published guidelines were identified by searching the Medline and Telemedicine Information Exchange (TIE) databases, and by performing a Google search using the term 'telemedicine guidelines'. Three types of guidelines were identified, namely clinical, operational and technical. Clinical guidelines included those for teleradiology, telepsychiatry, home telenursing, minor injuries telemedicine, surgical telemedicine, teledermatology and telepathology. Operational guidelines included those for email communication, Internet access and videoconferencing. Technical guidelines included those from the American Telemedicine Association and the US Office for the Advancement of Telehealth. The main standards relevant to telemedicine include those of the International Telecommunication Union and the DICOM standard. The scarcity of guidelines and standards suggests that telemedicine is not yet near to routine use. If an international telemedicine organization were to take responsibility for defining guidelines, under the direction of clinicians with appropriate telemedicine experience, this might speed up their development.

Board composition and corporate performance: How the Australian experience informs contrasting theories of corporate governance

In many respects, Australian boards more closely approach normative best practice guidelines for corporate governance than boards in other Western countries. Do Australian firms then demonstrate a board demographic-organisational performance link that has not been found in other economies? We examine the relationships between board demographics and corporate performance in 348 of Australia's largest publicly listed companies and describe the attributes of these firms and their boards. We find that, after controlling for firm size, board size is positively correlated with firm value. We also find a positive relationship between the proportion of inside directors and the market-based measure of firm performance. We discuss the implications of these findings and compare our findings to prevailing research in the US and the UK.

Habitat choice and vigilance behaviour of brush-tailed rock-wallabies (Petrogale penicillata) within their nocturnal foraging ranges

Habitat choice by brush-tailed rock-wallabies (Petrogale penicillata) in south-east Queensland was investigated by comparing the attributes of the nocturnal foraging locations that they selected with those of random locations within a radius of 50 m. Brush-tailed rock-wallabies were shown to select foraging locations on the basis of forage quality and/or their ability to see predators, rather than protection from predators amongst vegetation that could conceal them. Habitat choice may have been affected by limited food availability, as this study was conducted in the winter dry season. The attributes of foraging locations that brush- tailed rock-wallabies perceived as increasing their predation risk were assessed by recording the proportion of time that brush- tailed rock-wallabies spent vigilant while foraging. To measure vigilance, focal animals were observed with a night- vision scope for two minutes and the proportions of time spent vigilant and feeding were recorded. No measured feature of foraging locations was related to higher vigilance levels, suggesting that brush- tailed rock-wallabies did not alter their vigilance whether sheltered amongst grass tussocks or in open habitat, or whether feeding on good quality or poorer quality vegetation. Vigilance levels significantly declined as overnight temperatures decreased, which may have resulted from higher energy requirements of brush- tailed rock-wallabies during winter. The only factors that were found to significantly increase vigilance levels were high winds and moonlit nights. On bright nights, brush- tailed rock-wallabies were very unsettled and during high winds they often did not emerge to feed. More information is needed about how macropods detect predators at night before the effects of wind and light intensity upon vigilance can be fully understood.

A coupled knowledge-based expert system for design of liquid-retaining structures

This paper describes a coupled knowledge-based system (KBS) for the design of liquid-retaining structures, which can handle both the symbolic knowledge processing based on engineering heuristics in the preliminary synthesis stage and the extensive numerical crunching involved in the detailed analysis stage. The prototype system is developed by employing blackboard architecture and a commercial shell VISUAL RULE STUDIO. Its present scope covers design of three types of liquid-retaining structures, namely, a rectangular shape with one compartment, a rectangular shape with two compartments and a circular shape. Through custom-built interactive graphical user interfaces, the user is directed throughout the design process, which includes preliminary design, load specification, model generation, finite element analysis, code compliance checking and member sizing optimization. It is also integrated with various relational databases that provide the system with sectional properties, moment and shear coefficients and final member details. This system can act as a consultant to assist novice designers in the design of liquid-retaining structures with increase in efficiency and optimization of design output and automated record keeping. The design of a typical example of the liquid-retaining structure is also illustrated. (C) 2003 Elsevier B.V All rights reserved.

Applied physiology and game analysis of rugby union

Increased professionalism in rugby has elicited rapid changes in the fitness profile of elite players. Recent research, focusing on the physiological and anthropometrical characteristics of rugby players, and the demands of competition are reviewed. The paucity of research on contemporary elite rugby players is highlighted, along with the need for standardised testing protocols. Recent data reinforce the pronounced differences in the anthropometric and physical characteristics of the forwards and backs. Forwards are typically heavier, taller, and have a greater proportion of body fat than backs. These characteristics are changing, with forwards developing greater total mass and higher muscularity. The forwards demonstrate superior absolute aerobic and anaerobic power, and Muscular strength. Results favour the backs when body mass is taken into account. The scaling of results to body mass can be problematic and future investigations should present results using power function ratios. Recommended tests for elite players include body mass and skinfolds, vertical jump, speed, and the multi-stage shuttle run. Repeat sprint testing is a possible avenue for more specific evaluation of players. During competition, high-intensity efforts are often followed by periods of incomplete recovery. The total work over the duration of a game is lower in the backs compared with the forwards; forwards spend greater time in physical contact with the opposition while the backs spend more time in free running, allowing them to cover greater distances. The intense efforts undertaken by rugby players place considerable stress on anaerobic energy sources, while the aerobic system provides energy during repeated efforts and for recovery. Training should focus on repeated brief high-intensity efforts with short rest intervals to condition players to the demands of the game. Training for the forwards should emphasise the higher work rates of the game, while extended rest periods can be provided to the backs. Players should not only be prepared for the demands of competition, but also the stress of travel and extreme environmental conditions. The greater professionalism of rugby union has increased scientific research in the sport; however, there is scope for significant refinement of investigations on the physiological demands of the game, and sports-specific testing procedures.

A study of the radiation chemistry of poly(chlorotrifluoroethylene) by ESR spectroscopy

The ESR spectra of poly(chlorotrifluoroethylene) were recorded following gamma-radiolysis under vacuum at room temperature and 77 K. The very broad spectrum at 77 K revealed little fine structure with which to identity the radicals formed upon irradiation, but subsequent photobleaching and annealing studies, together with radiolytic studies at higher temperatures, afforded scope for making radical assignments. Both main-chain radicals and a range of chain-end radicals have been identified. The G-values for radical formation were 1.55, 0.36 and 0.32 at 77 K, 273 K and room temperature, respectively. (C) 2003 Elsevier Science Ltd. All rights reserved.

The formative platform of the Congress of Panama (1810-1826): the Pan-American conjecture revisited

This article examines the formative platform of the Congress of Panama of 1826. It seeks to support the hypothesis that the nature and scope of the first test of integration in the Western Hemisphere depended critically on the platform created by Simón Bolívar and other Latin American Independence heroes from the Declaration of Independence of Venezuela in 1810 until the last bilateral agreement of 1826. In that respect, it corroborates the Latin American Identity of the initiative.

The quest for a sustainable product: An environmental study of tyre recyclates

The main objective of the present study is to assess the environmental advantages of substituting aluminium for a polymer composite in the manufacture of a structural product (a frame to be used as a support for solar panels). The composite was made of polypropylene and a recycled tyres’ rubber granulate. Analysis of different composite formulations was performed, to assess the variation of the environmental impact with the percentage of rubber granulate incorporation. The results demonstrate that the decision on which of the two systems (aluminium or composite) has the best life cycle performance is strongly dependent on the End-of Life (EoL) stage of the composite frame. When the EoL is deposition in a landfill, the aluminium frame performs globally better than its composite counterpart. However, when it is incineration with energy recovery or recycling, the composite frame is environmentally preferable. The raw material production stage was found to be responsible for most of the impacts in the two frame systems. In that context, it was shown that various benefits can accrue in several environmental impact categories by recycling rubber tyres and using the resulting materials. This is in a significant part also due to the recycling of the steel in the tyres. The present work illustrates how it is possible to minimize the overall environmental impact of consumer products through the adequate selection of their constitutive materials in the design stage. Additionally it demonstrates how an adequate EoL planning can be an important issue when developing a sustainable product, since it can highly influence its overall life cycle performance.

Determinants of environmental disclosure in the annual reports of large companies operating in Portugal

Similarly to what has happened in other countries, since the early 1990s Portuguese companies have developed corporate environmental reporting practices in response to internal and external factors. This paper is based on empirical research directed to both the study of environmental reporting practices developed by Portuguese companies and the identification of the factors that explain the extent to which these companies disclose environmental information. This study focuses on the environmental disclosures made in the annual reports by a sample of 109 large firms operating in Portugal during the period 2002-04. Using the content analysis technique we have developed an index in order to assess the presence of the environmental disclosures in companies’ annual reports and their breadth. Based on the extant literature, several characteristics relating to firms’ attributes were selected and their influence on the level of environmental disclosure was tested empirically. The selected explanatory variables were firm size, industry membership, profitability, foreign ownership, quotation on the stock market and environmental certification. The results reveal that, in spite of the fact that the level of environmental information disclosed during the period 2002-04 is low, the extent of environmental disclosure has increased as well as the number of Portuguese companies that disclose environmental information. Moreover, the firm size and the fact that a company is listed on the stock market are positively related to the extent of environmental disclosure. This study adds to the international research on environmental disclosure by providing empirical data from a country, Portugal, where empirical evidence is still relatively unknown, extending the scope of the current understanding of the environmental reporting practices.

Evaluation of polymethylmethacrylate as ocular implant in rabbits subjected to evisceration

Spheres of different types of material are used for the replacement of lost volume after removal of the eye bulb or its content to prevent contraction of the orbital cavity. The aim of this study was to evaluate the scope of polymethylmethacrylate (PMMA) used as intraocular implant in eviscerated rabbit eye. Twelve New Zealand rabbits underwent unilateral evisceration of the left eye, with subsequent implantation of PMMA sphere 12 mm in diameter. Clinical evaluation was performed daily during the first 15 days after surgery and every 15 days until the end of the study period (180 days). For the histopathological analysis, three animals per trial underwent enucleation at 15, 45, 90 and 180 days after evisceration. There was no wound dehiscence, signs of infection or implant extrusion in any animal throughout the study period. Histological examination revealed the formation of fibrovascular tissue around the implants. The PMMA behaved as inert and non-integrable.

Evaluation of collaborative strategies for ecotourism and recreational activities in natural parks of Rio de Janeiro

In the city of Rio de Janeiro, the management agencies of environmental conservation units of the park type have been attempting to meet five primary objectives set by the National System for Conservation Units (NSCU), using participatory management guidelines for these units. Two of these objectives relate to the development of recreation activities that involve contact with nature and ecological tourism. This article presents the analyses and conclusions regarding the implementation of collaborative strategies with businesses to achieve such objectives; it is part of a series of research studies having a broader scope. Case studies were conducted in eight parks by means of dozens of interviews with managers and other interested social actors, as well as by documentary research and direct observation. The results suggest that the ecotourism objective is still far from being reached, and that the collaborative strategies used are not sufficient to compensate for the organizational, material and human limitations that encumber these agencies. It was also concluded for the sample that there lacks a strategic vision on the part of the three branches of government involved in the management of these parks in the sense of viewing ecotourism in the city's conservation units as a powerful means to foster local sustainable development.

Public hearings as a tool to improve participation in regulatory policies: case study of the National Agency of Electric Energy

The participation of citizens in public policies is an opportunity not only to educate them, but also to increase their empowerment. However, the best way for deploying participatory policies, defining their scope and approach, still remains an open and continuous debate. Using as a case study the Brazilian National Agency of Electric Energy (Aneel), with its public hearings about tariff review, this paper aims at analyzing the democratic aspects of these hearings and challenges the hypothesis of many scholars about the social participation bias in this kind of procedure. This study points out a majority participation of experts, contrasting with the political content of discussions. And, this way, it contributes to a critical analysis of the public hearings as a participatory tool, indicating their strengths and their aspects which deserve a special attention.