Ultra-trace monitoring of copper in environmental and biological samples by inductively coupled plasma atomic emission spectrometry after separation and preconcentration by using octadecyl silica membrane disks modified by a new schiff's base

Ultra-trace amounts of Cu(II) were separated and preconcentrated by solid phase extraction on octadecyl-bonded silica membrane disks modified with a new Schiff,s base (Bis- (2-Hydroxyacetophenone) -2,2-dimethyl-1,3-propanediimine) (SBTD) followed by elution and inductively coupled plasma atomic emission spectrometric detection. The method was applied as a separation and detection method for copper(II) in environmental and biological samples. Extraction efficiency and the influence of sample matrix, flow rate, pH, and type and minimum amount of stripping acid were investigated. The concentration factor and detection limit of the proposed method are 500 and 12.5 pg mL-1, respectively.

Automated flow-injection method for cadmium determination with pre-concentration and reagent preparation on-line

The spectrophotometric determination of Cd(II) using a flow injection system provided with a solid-phase reactor for cadmium preconcentration and on-line reagent preparation, is described. It is based on the formation of a dithizone-Cd complex in basic medium. The calibration curve is linear between 6 and 300 µg L-1 Cd(II), with a detection limit of 5.4 µg L-1, an RSD of 3.7% (10 replicates in duplicate) and a sample frequency of 11.4 h-1. The proposed method was satisfactorily applied to the determination of Cd(II) in surface, well and drinking waters.

Flow analysis by using solenoid valves for As(III) determination in natural waters by an on-line separation and pre-concentration system coupled to a tungsten coil atomizer

A flow system coupled to a tungsten coil atomizer in an atomic absorption spectrometer (TCA-AAS) was developed for As(III) determination in waters, by extraction with sodium diethyldithiocarbamate (NaDDTC) as complexing agent, and by sorption of the As(III)-DDTC complex in a micro-column filled with 5 mg C18 reversed phase (10 µL dry sorbent), followed by elution with ethanol. A complete pre-concentration/elution cycle took 208 s, with 30 s sample load time (1.7 mL) and 4 s elution time (71 µL). The interface and software for the synchronous control of two peristaltic pumps (RUN/ STOP), an autosampler arm, seven solenoid valves, one injection valve, the electrothermal atomizer and the spectrometer Read function were constructed. The system was characterized and validated by analytical recovery studies performed both in synthetic solutions and in natural waters. Using a 30 s pre-concentration period, the working curve was linear between 0.25 and 6.0 µg L-1 (r = 0.9976), the retention efficiency was 94±1% (6.0 µg L-1), and the pre-concentration coefficient was 28.9. The characteristic mass was 58 pg, the mean repeatability (expressed as the variation coefficient) was 3.4% (n=5), the detection limit was 0.058 µg L-1 (4.1 pg in 71 µL of eluate injected into the coil), and the mean analytical recovery in natural waters was 92.6 ± 9.5 % (n=15). The procedure is simple, economic, less prone to sample loss and contamination and the useful lifetime of the micro-column was between 200-300 pre-concentration cycles.

Small scale energy production in Helsinki Metropolitan area in emission trading point of view

Emission trading with greenhouse gases and green certificates are part if the climate policy the main target of which is reduce greenhouse gas emissions. The carbon dioxide and fine particle emissions of energy production in Helsinki Metropolitan area are calculated in this study. The analysis is made mainly by district heating point of view and the changes of the district heating network are assessed. Carbon dioxide emissions would be a bit higher, if the district heating network is expanded, but then the fine particle emissions would be much lower. Carbon dioxide emissions are roughly 10 % higher, if the district heating network is expanded at same rate as it has in past five years in the year 2030. The expansion of district heating network would decrease the fine particle emissions about 40 %. The cost of the expansion is allocated to be reduction cost of the fine particle emissions, which is considerably higher than the traditional reduction methods costs. The possible new nuclear plant would reduce the emissions considerably and the costs of the nuclear plant would be relatively low comparing the other energy production methods.

Non-thermal emission from microquasar/ISM interaction

Context. The interaction of microquasar jets with their environment can produce non-thermal radiation as in the case of extragalactic outflows impacting on their surroundings. Significant observational evidence of jet/medium interaction in galactic microquasars has been collected in the past few years, although little theoretical work has been done regarding the resulting non-thermal emission. Aims. In this work, we investigate the non-thermal emission produced in the interaction between microquasar jets and their environment, and the physical conditions for its production. Methods. We developed an analytical model based on those successfully applied to extragalactic sources. The jet is taken to be a supersonic and mildly relativistic hydrodynamical outflow. We focus on the jet/shocked medium structure in its adiabatic phase, and assume that it grows in a self-similar way. We calculate the fluxes and spectra of the radiation produced via synchrotron, inverse Compton, and relativistic bremsstrahlung processes by electrons accelerated in strong shocks. A hydrodynamical simulation is also performed to investigate further the jet interaction with the environment and check the physical parameters used in the analytical model. Results. For reasonable values of the magnetic field, and using typical values of the external matter density, the non-thermal particles could produce significant amounts of radiation at different wavelengths, although they do not cool primarily radiatively, but by adiabatic losses. The physical conditions of the analytical jet/medium interaction model are consistent with those found in the hydrodynamical simulation. Conclusions. Microquasar jet termination regions could be detectable at radio wavelengths for current instruments sensitive to ~arcminute scales. At X-ray energies, the expected luminosities are moderate, although the emitter is more compact than the radio one. The source may be detectable by XMM-Newton or Chandra, with 1-10 arcsec of angular resolution. The radiation at gamma-ray energies may be within the detection limits of the next generation of satellite and ground-based instruments.

X-ray and radio observations of RX J1826.2-1450/LS 5039

RX J1826.2-1450/LS 5039 has been recently proposed to be a radio emitting high mass X-ray binary. In this paper, we present an analysis of its X-ray timing and spectroscopic properties using different instruments on board the RXTE satellite. The timing analysis indicates the absence of pulsed or periodic emission on time scales of 0.02-2000 s and 2-200 d, respectively. The source spectrum is well represented by a power-law model, plus a Gaussian component describing a strong iron line at 6.6 keV. Significant emission is seen up to 30 keV, and no exponential cut-off at high energy is required. We also study the radio properties of the system according to the GBI-NASA Monitoring Program. RX J1826.2-1450/LS 5039 continues to display moderate radio variability with a clearly non-thermal spectral index. No strong radio outbursts have been detected after several months.

A novel method for fast enrichment and monitoring of hexavalent and trivalent chromium at the ppt level with modified silica MCM-41 and its determination by inductively coupled plasma optical emission spectrometry

Chromium(III) at the ng L-1 level was extracted using partially silylated MCM-41 modified by a tetraazamacrocyclic compound (TAMC) and determined by inductively coupled plasma optical emision spectrometry (ICP OES). The extraction time and efficiency, pH and flow rate, type and minimum amount of stripping acid, and break- through volume were investigated. The method's enrichment factor and detection limit are 300 and 45.5 pg mL-1, respectively. The maximum capacity of the 10 mg of modified silylated MCM-41 was found to be 400.5±4.7 µg for Cr(III). The method was applied to the determination of Cr(III) and Cr(VI) in the wastewater of the chromium electroplating industry and in environmental and biological samples (black tea, hot and black pepper).

Positron emission tomography in the diagnosis and staging of pancreatic and neuroendocrine tumors

Tutkimuksen tausta ja tavoitteet: Viimeaikaisesta perinteisten kuvantamismenetelmien kehityksestä huolimatta sekä haima- että neuroendokriinisten (NE) kasvaimien diagnostiikka on haastavaa. Uudentyyppinen kuvantamismenetelmä, fuusio positroniemissiotomografia-tietokonetomografia (PET/TT), on lupaava näiden kasvainten erotusdiagnostiikassa ja levinneisyyden arvioinnissa. Huolimatta alustavista lupaavista tutkimustuloksista, PET/TT:n rooli on toistaiseksi vielä epäselvä sekä haima- että NE-kasvaimissa eikä se näin ollen ole vakiintunut kliiniseen hoitokäytäntöön. Väitöskirjatyön tavoitteena oli selvittää PET/TT -menetelmän käyttökelpoisuutta haima- ja NE-kasvaimien diagnostiikassa. Kahden ensimmäisen osatyön prospektiivisessa tutkimuksessa potilaat, joilla epäiltiin haimakasvainta, kuvannettiin PET/TT:llä käyttäen merkkiaineena fluorideoxyglukoosia (¹⁸F-FDG) kasvaimen aineenvaihdunnan arvioimiseksi ja kasvaimen verenvirtausta arviointiin käyttäen merkkiaineena radiovettä (¹⁵O-H₂O). Kolmen muun osatyön tavoitteena oli selvittää dihydroxyfenylalaniini (18F-DOPA) PET -menetelmää erilaisten NE-kasvaimien diagnostiikassa ja levinneisyyden arvioinnissa. Tulokset: Haimakasvaimien ensivaiheen diagnostiikassa ¹⁸F-FDG-PET/TT:llä oli korkeampi diagnostinen tarkkuus verrattuna titokoneleike- (TT) ja magneettikuvantamiseen (MK) (89% vs. 76% ja 79%). Etenkin pahanlaatuiseksi epäillyn sappitiehytahtauman erotusdiagnostiikassa ¹⁸F-FDG-PET/TT:n positiivinen ennustearvo (92%) oli korkea. Haimasyövän levinneisyyden arvioinnissa ¹⁸F-FDG-PET/TT:n herkkyys oli huono (30%) paikallisen taudin osoittamisessa. Sen sijaan etäpesäkkeiden osoittamisessa ¹⁸F-FDG-PET/TT oli merkittävästi herkempi menetelmä verrattuna TT ja magneettikuvantamiseen (88% vs. 38%). Verrattaessa erilaisten haimakasvaimien ja normaalin haimakudoksen aineenvaihduntaa ja verenvirtausta, aineenvaihdunta/verenvirtaus suhde oli merkittävästi korkeampi pahanlaatuisissa haimakasvaimissa (P<0.05). Lisäksi kasvaimen korkea aineenvaihdunta/verenvirtaus suhde viittasi huonompaan taudin ennusteeseen. ¹⁸F-DOPA-PET löysi seitsemän kahdeksasta insulinoomasta ja oli positiivinen myös kahdella potilaalla, joilla todettiin haiman saarakesoluhyperplasia. Perustuen alustaviin tuloksiin, rutiinikäytössä oleva karbidopa esilääke ennen ¹⁸F-DOPA-PET kuvantamista peitti insulinooma löydöksen kahdella potilaalla kolmesta. NE-kasvaiminen diagnostiikassa 82 potilaan aineisto osoitti ¹⁸F-DOPA PET kuvantamisen tarkkuudeksi 90%. Etenkin feokromosytoomien ensivaiheen diagnostiikassa ja NE-kasvaimen uusiutumaa epäiltäessä menetelmän tarkkuus oli korkea. Kokonaisuudessaan 59%:lla aineiston potilaista ¹⁸F-DOPA-PET kuvantamisella oli vaikutusta kliinisiin hoitoratkaisuihin. Johtopäätökset: PET/TT käyttäen merkkiaineena ¹⁸F-FDG:tä ja radiovettä osoittautui käyttökelpoiseksi menetelmäksi haimakasvaimien erotusdiagnostiikassa. Lisäksi ¹⁸F-FDG-PET/TT oli hyödyllinen haimasyövän etäpesäkkeiden arvioinnissa. Tutkimus osoitti myös ¹⁸F-DOPA-PET kuvantamisen olevan luotettava menetelmä insulinoomien ja muiden vatsan alueen NE-kasvaimien ensivaiheen diagnostiikassa sekä levinneisyyden arvioinnissa, etenkin muiden kuvantamislöydösten ollessa ristiriitaisia. PET kuvantamisella oli merkittävä vaikutus potilaiden kliiniseen hoitokäytäntöön sekä haima- että NE-kasvaimissa.

Blackbody emission under laser excitation of silicon nanopowder produced by plasma-enhanced chemical-vapor deposition

Previous results concerning radiative emission under laser irradiation of silicon nanopowder are reinterpreted in terms of thermal emission. A model is developed that considers the particles in the powder as independent, so under vacuum the only dissipation mechanism is thermal radiation. The supralinear dependence observed between the intensity of the emitted radiation and laser power is predicted by the model, as is the exponential quenching when the gas pressure around the sample increases. The analysis allows us to determine the sample temperature. The local heating of the sample has been assessed independently by the position of the transverse optical Raman mode. Finally, it is suggested that the photoluminescence observed in porous silicon and similar materials could, in some cases, be blackbody radiation

Microwave Slot Transmission Line Filled with Ferroelectric and Ferromagnetic Layers

Now when the technology is fast developing it is very important to investigate new hybrid structures. One way is to use ferrite ferroelectric layered structures. Theoretical and experimental investigation of such structures was made. These structures have advantages of both layers and it is possible to tune the behavior of this structure by external electric and magnetic field. But these structures have some disadvantages connected with presence of thick ferroelectric layer. One way to overcome this problem is to use slotline. So this is another new way to create hybrid ferrite ferroelectric structures, but it is needed to create new theory and find experimental proof that the behavior of these structures can be tuned with external magnetic and electric fields.

Disseny i elaboració d'un gimnàs on-line

L’evolució que ha experimentat la societat, les grans ciutats, la industrialització i molts altres factors han modificat l’estil de vida de les persones accentuant-ne, irremediablement, el sedentarisme i l’abstinència de realitzar exercici físic. La pràctica esportiva i/o d’exercici físic realitzada sota les condicions recomanades pels professionals, és beneficiosa per millorar el nivell de salut o mantenir-lo en tot el possible, ja que provoca modificacions beneficioses sobre el metabolisme, el sistema cardiovascular i l’aparell locomotor. Lamentablement, l’hàbit de realitzar exercici físic no és comú en totes les persones, ja sigui per l’estil de vida que genera incompatibilitats d’horaris amb la feina, fills i familiars o bé per mandra o desgana d’haver d’aprofitar aquelles estones de temps lliure per dedicar-los al culte del cos i de la salut. Els efectes negatius que suposa una modalitat de vida sedentària per a la salut són notablement elevats, amb la qual cosa, cal buscar sistemes per augmentar l’ interès de la població per la pràctica de l’esport i l’activitat física. La creació d’aquest projecte neix de la idea d’unir el fet d’enginyar un mètode per incrementar l’interès de les persones per l’exercici físic amb els avenços tecnològics que s’han realitzat aquesta última dècada relacionats amb el desenvolupament web i multimèdia. A grans trets, la idea general d’aquest projecte es basa en el cas d’un gimnàs real i en actiu, amb necessitat de crear un portal web que serveixi alhora de pàgina web informativa i d’eina de gestió acadèmica del centre proporcionant certes funcionalitats als clients tot presentant-los una nova modalitat de realitzar exercici físic dirigit: realitzar-lo des de casa. Per desenvolupar tot el sistema informàtic que ho durà a terme, després de realitzar una recerca, anàlisi i elecció de les eines mitjançant les quals poder-ho realitzar, s’ha optat per crear l’entorn web mitjançant els llenguatges HTML i PHP en combinació amb els fulls d’estil CSS. Pel que fa a l’entorn de desenvolupament, s’ha utilitzat Notepad++ i com a entorn de proves, WAMP Server. Per últim, pel que fa a la transmissió del contingut multimèdia (vídeos de les sessions d’activitats) s’ha utilitzat Flash Media Interactive Server en combinació de Flash Media Live Encoder per codificar-ne el contingut. L’usuari final, des de qualsevol punt del planeta, podrà realitzar (sempre i quan disposi del temps i el material necessari i una connexió a Internet) en temps real i en directe les classes dirigides que es realitzen al centre. Tanmateix, també s’ha desenvolupat una botiga virtual on qualsevol persona podrà comprar-hi, entre d’altres coses relacionades amb la pràctica de l’exercici físic, tot el material necessari per realitzar qualsevol de les activitats que s’imparteixen al gimnàs i ho rebrà còmodament a casa. Aprofitar unes circumstàncies econòmiques adverses per generar una nova manera de captar clients proporcionant-los una alternativa econòmica, diferent, nova i original d’anar al gimnàs. Temps de crisis, temps d’oportunitats. Aquesta és la moralitat que pretén donar aquest projecte.

Desenvolupament d'una aplicació per a la creació de pressupostos on-line

En aquests moments, el mercat no es troba en una bona situació, per aquest motiu les empreses han de buscar noves maneres de créixer, expandir-se i noves formes d’interactuar amb els clients. La idea original d’aquest projecte sorgeix de la necessitat de disposar d’una manera diferent de promocionar-se i oferir nous serveis a través d’internet mitjançant una pàgina web. Degut a la situació actual, el preu és un aspecte molt important i influent a l’hora de realitzar una obra. Per aquest motiu es va pensar que seria molt interessant que el client pogués demanar de forma fàcil i ràpida un pressupost, i a l’instant tingués un preu orientatiu del que li pot costar la obra. D’aquesta manera l’interessat s’estalvia i agilitza molts passos previs abans de començar una obra. Després d’analitzar quina era la millor manera de portar a terme el projecte informàtic, s’ha determinat que la pàgina web es desenvoluparà utilitzant els llenguatges HTML i PHP combinant-lo amb el framework CodeIgniter. El disseny de la web es realitzarà mitjançant fulles d’estil CSS conjuntament amb el framework BootStrap. Per realitzar l’aplicació web que realitza els pressupostos s’utilitzarà AJAX i jQuery perquè d’aquesta manera el procés sigui dinàmic. L’entorn de desenvolupament escollit és el NetBeans i per provar el projecte s’utilitza el XAMPP. Un usuari només necessitarà un navegador i connexió a internet per fer servir totes les funcions de la web. Podrà realitzar pressupostos, concertar visites, contactar i per suposat veure tota la part informativa de la pàgina

Enhancing Customer Knowledge and Its Sharing At a Paper Production Line

This study has been made for specific paper production line at an international forest industry company in Finland. The main purpose for the study was a need to examine the current situation of the customer knowledge and its’ sharing at case production line, recognize the problems in it and finally, find out the improvement actions. The study is composed of theoretical and empirical parts. In theoretical part, knowledge management and information sharing in addition to customer knowledge management are presented. Empirical data from case production line was collected by using survey questionnaires. The results are analyzed in discussion and conclusions and finally, study ends with summary which includes recommendations. Based on the study, the amount and quality of customer knowledge and gaining and transferring the customer knowledge were found as the main challenges. The proposed solutions were discovered from moving towards more dynamic operating environment and in the area of customer knowledge management, especially from the communities of creation.