CO2 soil flux baseline at the technological development plant for CO2 injection at Hontomin (Burgos, Spain)

From the end of 2013 and during the following two years, 20 kt of CO2sc are planned to be injected in a saline reservoir (1500 m depth) at the Hontomín site (NE Spain). The target aquifers are Lower Jurassic limestone formations which are sealed by Lower Cretaceous clay units at the Hontomín site (NE Spain). The injection of CO2 is part of the activities committed in the Technology Development phase of the EC-funded OXYCFB300 project (European Energy Program for Recovery – EEPR, http://www.compostillaproject.eu), which include CO2 injection strategies, risk assessment, and testing and validating monitoring methodologies and techniques. Among the monitoring works, the project is intended to prove that present-day technology is able to monitor the evolution of injected CO2 in the reservoir and to detect potential leakage. One of the techniques is the measurement of CO2 flux at the soil–atmosphere interface, which includes campaigns before, during and after the injection operations. In this work soil CO2 flux measurements in the vicinity of oil borehole, drilled in the eighties and named H-1 to H-4, and injection and monitoring wells were performed using an accumulation chamber equipped with an IR sensor. Seven surveys were carried out from November 2009 to summer 2011. More than 4000 measurements were used to determine the baseline flux of CO2 and its seasonal variations. The measured values were low (from 5 to 13 g m−2 day−1) and few outliers were identified, mainly located close to the H-2 oil well. Nevertheless, these values cannot be associated to a deep source of CO2, being more likely related to biological processes, i.e. soil respiration. No anomalies were recognized close to the deep fault system (Ubierna Fault) detected by geophysical investigations. There, the CO2 flux is indeed as low as other measurement stations. CO2 fluxes appear to be controlled by the biological activity since the lowest values were recorded during autumn-winter seasons and they tend to increase in warm periods. Two reference CO2 flux values (UCL50 of 5 g m−2 d−1 for non-ploughed areas in autumn–winter seasons and 3.5 and 12 g m−2 d−1 for in ploughed and non-ploughed areas, respectively, in spring–summer time, and UCL99 of 26 g m−2 d−1 for autumn–winter in not-ploughed areas and 34 and 42 g m−2 d−1 for spring–summer in ploughed and not-ploughed areas, respectively) were calculated. Fluxes higher than these reference values could be indicative of possible leakage during the operational and post-closure stages of the storage project.

Development of a Knowledge Base for smart screening of language disorders in primary care

Monitoring of neuro-evolutive development from birth until the age of six is a decisive factor in a child's quality of life. Early detection of development disorders in early childhood can facilitate necessary diagnosis and/or treatment. Primary-care pediatricians play a key role in early detection of development alterations as they can undertake the preventive and therapeutic actions necessary in the interest of a child's optimal development. The focus of this research paper is the construction of a Knowledge Base for smart screening aimed to assist pediatricians in processes of early referral in language disorders. The proposed model provides health professionals with a decision-making tool that supports referral processes. In this way, essential diagnostic and/or therapeutic actions are triggered for a comprehensive individual development. The resulting system was developed on the basis of an analysis and verification of 21 cases of children with language disorders.

Integration of Correlation Processes in Design Systems.

The integration of correlation processes in design systems has as a target measurements in 3D directly and according to the users criteria in order to generate the required database for the development of the project. In the phase of photogrammetric works, internal and external orientation parameters are calculated and stereo models are created from standard images. The aforementioned are integrated in the system where the measurement of the selected items is done by applying developed correlation algorithms. The processing period has the tools to carry out the calculations in an easy and automatic way, as well as image measurement techniques to acquire the most correct information. The proposed software development is done on Visual Studio platforms for PC, applying the most apt codes and symbols according to the terms of reference required for the design. The results of generating the data base in an interactive way with the geometric study of the structures, facilitates and improves the quality of the works in the projects.

Evaluation of Development Projects: a Process-Centered Approach in the Outskirts of Lima, Peru.

Development cooperation projects work with people involved in processes of change and social transformation. While the main objective of the intervention is the development process itself, the project?s quality will be determined by the way of implementing it. Its success lies in the sustainability of the generated processes and the connection with them by the involved actors. The evaluation analyses both aspects. This article examines the evaluation, under a process approach, of a project on urban agriculture in Lima (Peru). The results show that the use of this approach, which combines different evaluation tools, allows the identification and analysis of the processes with the involved members, providing a better understanding of the real sustainability of the results.

Development and implementation of a virtual laboratory for training process improvement in the mechanics of continuous media

The project arises from the need to develop improved teaching methodologies in field of the mechanics of continuous media. The objective is to offer the student a learning process to acquire the necessary theoretical knowledge, cognitive skills and the responsibility and autonomy to professional development in this area. Traditionally the teaching of the concepts of these subjects was performed through lectures and laboratory practice. During these lessons the students attitude was usually passive, and therefore their effectiveness was poor. The proposed methodology has already been successfully employed in universities like University Bochum, Germany, University the South Australia and aims to improve the effectiveness of knowledge acquisition through use by the student of a virtual laboratory. This laboratory allows to adapt the curricula and learning techniques to the European Higher Education and improve current learning processes in the University School of Public Works Engineers -EUITOP- of the Technical University of Madrid -UPM-, due there are not laboratories in this specialization. The virtual space is created using a software platform built on OpenSim, manages 3D virtual worlds, and, language LSL -Linden Scripting Language-, which imprints specific powers to objects. The student or user can access this virtual world through their avatar -your character in the virtual world- and can perform practices within the space created for the purpose, at any time, just with computer with internet access and viewfinder. The virtual laboratory has three partitions. The virtual meeting rooms, where the avatar can interact with peers, solve problems and exchange existing documentation in the virtual library. The interactive game room, where the avatar is has to resolve a number of issues in time. And the video room where students can watch instructional videos and receive group lessons. Each audiovisual interactive element is accompanied by explanations framing it within the area of knowledge and enables students to begin to acquire a vocabulary and practice of the profession for which they are being formed. Plane elasticity concepts are introduced from the tension and compression testing of test pieces of steel and concrete. The behavior of reticulated and articulated structures is reinforced by some interactive games and concepts of tension, compression, local and global buckling will by tests to break articulated structures. Pure bending concepts, simple and composite torsion will be studied by observing a flexible specimen. Earthquake resistant design of buildings will be checked by a laboratory test video.

Development of One Meter Long Double-Sided CeO2 Buffered Ni-5at.W Templates by Reel-to-Reel Chemical Solution Deposition Route

High performance long-length coated conductors fabricated using various techniques have attracted a lot of interest recently. In this work, a reel-to-reel design for depositing double-sided coatings on long-length flexible metallic tapes via a chemical solution method is proposed and realized. The major achievement of the design is to combine the dip coating and drying processes in order to overcome the technical difficulties of dealing with the wet films on both sides of the tape. We report the successful application of the design to fabricate a one-meter-long double side coated CeO2/Ni-5at%W template. The CeO2 films on both sides exhibit a dense, crack-free morphology, and a high fraction of cube texture on the surface. Homogeneity studies on global texture over the length also reveal that the average full width at half maximum values of the in-plane and out-of-plane orientation on the CeO2 layer are 7.2 ° and 5.8° with standard deviation of 0.26° and 0.34°, respectively, being indicative of the high quality epitaxial growth of the films prepared in the continuous manner. An all chemical solution derived YBCOLow-TFA/Ce0.9La0.1O2 /Gd2Zr2O7/CeO2 structure is obtained on a short sample, demonstrating the possibility of producing long-length texture templates for coated conductors by this low cost deposition route.

Exploring cognition processes in second language acquisition: the case of cognates and false-friends in EST

This article explores one aspect of the processing perspective in L2 learning in an EST context: the processing of new content words, in English, of the type ‘cognates’ and ‘false friends’, by Spanish speaking engineering students. The paper does not try to offer a comprehensive overview of language acquisition mechanisms, but rather it is intended to review more narrowly how our conceptual systems, governed by intricately linked networks of neural connections in the brain, make language development possible, creating, at the same time, some L2 processing problems. The case of ‘cognates and false friends’ in specialised contexts is brought here to illustrate some of the processing problems that the L2 learner has to confront, and how mappings in the visual, phonological and semantic (conceptual) brain structures function in second language processing of new vocabulary. Resumen Este artículo pretende reflexionar sobre un aspecto de la perspectiva del procesamiento de segundas lenguas (L2) en el contexto del ICT: el procesamiento de palabras nuevas, en inglés, conocidas como “cognados” y “falsos amigos”, por parte de estudiantes de ingeniería españoles. No se pretende ofrecer una visión completa de los mecanismos de adquisición del lenguaje, más bien se intenta mostrar cómo nuestro sistema conceptual, gobernado por una complicada red de conexiones neuronales en el cerebro, hace posible el desarrollo del lenguaje, aunque ello conlleve ciertas dificultades en el procesamiento de segundas lenguas. El caso de los “cognados” y los “falsos amigos”, en los lenguajes de especialidad, se trae para ilustrar algunos de los problemas de procesamiento que el estudiante de una lengua extranjera tiene que afrontar y el funcionamiento de las correspondencias entre las estructuras visuales, fonológicas y semánticas (conceptuales) del cerebro en el procesamiento de nuevo vocabulario.

Modelling spatial decisión support systems focused on the development of a data warehouse: applying software engineering

Nowadays, organizations have plenty of data stored in DB databases, which contain invaluable information. Decision Support Systems DSS provide the support needed to manage this information and planning médium and long-term ?the modus operandi? of these organizations. Despite the growing importance of these systems, most proposals do not include its total evelopment, mostly limiting itself on the development of isolated parts, which often have serious integration problems. Hence, methodologies that include models and processes that consider every factor are necessary. This paper will try to fill this void as it proposes an approach for developing spatial DSS driven by the development of their associated Data Warehouse DW, without forgetting its other components. To the end of framing the proposal different Engineering Software focus (The Software Engineering Process and Model Driven Architecture) are used, and coupling with the DB development methodology, (and both of them adapted to DW peculiarities). Finally, an example illustrates the proposal.

Application of user-centered design in the development of an atomated/assisted testing system for self-service devices

Automated Teller Machines (ATMs) are sensitive self-service systems that require important investments in security and testing. ATM certifications are testing processes for machines that integrate software components from different vendors and are performed before their deployment for public use. This project was originated from the need of optimization of the certification process in an ATM manufacturing company. The process identifies compatibility problems between software components through testing. It is composed by a huge number of manual user tasks that makes the process very expensive and error-prone. Moreover, it is not possible to fully automate the process as it requires human intervention for manipulating ATM peripherals. This project presented important challenges for the development team. First, this is a critical process, as all the ATM operations rely on the software under test. Second, the context of use of ATMs applications is vastly different from ordinary software. Third, ATMs’ useful lifetime is beyond 15 years and both new and old models need to be supported. Fourth, the know-how for efficient testing depends on each specialist and it is not explicitly documented. Fifth, the huge number of tests and their importance implies the need for user efficiency and accuracy. All these factors led us conclude that besides the technical challenges, the usability of the intended software solution was critical for the project success. This business context is the motivation of this Master Thesis project. Our proposal focused in the development process applied. By combining user-centered design (UCD) with agile development we ensured both the high priority of usability and the early mitigation of software development risks caused by all the technology constraints. We performed 23 development iterations and finally we were able to provide a working solution on time according to users’ expectations. The evaluation of the project was carried out through usability tests, where 4 real users participated in different tests in the real context of use. The results were positive, according to different metrics: error rate, efficiency, effectiveness, and user satisfaction. We discuss the problems found, the benefits and the lessons learned in the process. Finally, we measured the expected project benefits by comparing the effort required by the current and the new process (once the new software tool is adopted). The savings corresponded to 40% less effort (man-hours) per certification. Future work includes additional evaluation of product usability in a real scenario (with customers) and the measuring of benefits in terms of quality improvement.

Analysis of Contributions to NO2 Ambient Air Quality Levels in Madrid City (Spain) through Modeling. Implications for the Development of Policies and Air Quality Monitoring

As environmental standards become more stringent (e.g. European Directive 2008/50/EC), more reliable and sophisticated modeling tools are needed to simulate measures and plans that may effectively tackle air quality exceedances, common in large cities across Europe, particularly for NO2. Modeling air quality in urban areas is rather complex since observed concentration values are a consequence of the interaction of multiple sources and processes that involve a wide range of spatial and temporal scales. Besides a consistent and robust multi-scale modeling system, comprehensive and flexible emission inventories are needed. This paper discusses the application of the WRF-SMOKE-CMAQ system to the Madrid city (Spain) to assess the contribution of the main emitting sectors in the region. A detailed emission inventory was compiled for this purpose. This inventory relies on bottom-up methods for the most important sources. It is coupled with the regional traffic model and it makes use of an extensive database of industrial, commercial and residential combustion plants. Less relevant sources are downscaled from national or regional inventories. This paper reports the methodology and main results of the source apportionment study performed to understand the origin of pollution (main sectors and geographical areas) and define clear targets for the abatement strategy. Finally the structure of the air quality monitoring is analyzed and discussed to identify options to improve the monitoring strategy not only in the Madrid city but the whole metropolitan area.

Development and implementation of an air quality integrated assessment modelling system for the Iberian Peninsula

La mejora de la calidad del aire es una tarea eminentemente interdisciplinaria. Dada la gran variedad de ciencias y partes involucradas, dicha mejora requiere de herramientas de evaluación simples y completamente integradas. La modelización para la evaluación integrada (integrated assessment modeling) ha demostrado ser una solución adecuada para la descripción de los sistemas de contaminación atmosférica puesto que considera cada una de las etapas involucradas: emisiones, química y dispersión atmosférica, impactos ambientales asociados y potencial de disminución. Varios modelos de evaluación integrada ya están disponibles a escala continental, cubriendo cada una de las etapas antesmencionadas, siendo el modelo GAINS (Greenhouse Gas and Air Pollution Interactions and Synergies) el más reconocido y usado en el contexto europeo de toma de decisiones medioambientales. Sin embargo, el manejo de la calidad del aire a escala nacional/regional dentro del marco de la evaluación integrada es deseable. Esto sin embargo, no se lleva a cabo de manera satisfactoria con modelos a escala europea debido a la falta de resolución espacial o de detalle en los datos auxiliares, principalmente los inventarios de emisión y los patrones meteorológicos, entre otros. El objetivo de esta tesis es presentar los desarrollos en el diseño y aplicación de un modelo de evaluación integrada especialmente concebido para España y Portugal. El modelo AERIS (Atmospheric Evaluation and Research Integrated system for Spain) es capaz de cuantificar perfiles de concentración para varios contaminantes (NO2, SO2, PM10, PM2,5, NH3 y O3), el depósito atmosférico de especies de azufre y nitrógeno así como sus impactos en cultivos, vegetación, ecosistemas y salud como respuesta a cambios porcentuales en las emisiones de sectores relevantes. La versión actual de AERIS considera 20 sectores de emisión, ya sea equivalentes a sectores individuales SNAP o macrosectores, cuya contribución a los niveles de calidad del aire, depósito e impactos han sido modelados a través de matrices fuentereceptor (SRMs). Estas matrices son constantes de proporcionalidad que relacionan cambios en emisiones con diferentes indicadores de calidad del aire y han sido obtenidas a través de parametrizaciones estadísticas de un modelo de calidad del aire (AQM). Para el caso concreto de AERIS, su modelo de calidad del aire “de origen” consistió en el modelo WRF para la meteorología y en el modelo CMAQ para los procesos químico-atmosféricos. La cuantificación del depósito atmosférico, de los impactos en ecosistemas, cultivos, vegetación y salud humana se ha realizado siguiendo las metodologías estándar establecidas bajo los marcos internacionales de negociación, tales como CLRTAP. La estructura de programación está basada en MATLAB®, permitiendo gran compatibilidad con software típico de escritorio comoMicrosoft Excel® o ArcGIS®. En relación con los niveles de calidad del aire, AERIS es capaz de proveer datos de media anual y media mensual, así como el 19o valor horario más alto paraNO2, el 25o valor horario y el 4o valor diario más altos para SO2, el 36o valor diario más alto para PM10, el 26o valor octohorario más alto, SOMO35 y AOT40 para O3. En relación al depósito atmosférico, el depósito acumulado anual por unidad de area de especies de nitrógeno oxidado y reducido al igual que de azufre pueden ser determinados. Cuando los valores anteriormente mencionados se relacionan con características del dominio modelado tales como uso de suelo, cubiertas vegetales y forestales, censos poblacionales o estudios epidemiológicos, un gran número de impactos puede ser calculado. Centrándose en los impactos a ecosistemas y suelos, AERIS es capaz de estimar las superaciones de cargas críticas y las superaciones medias acumuladas para especies de nitrógeno y azufre. Los daños a bosques se calculan como una superación de los niveles críticos de NO2 y SO2 establecidos. Además, AERIS es capaz de cuantificar daños causados por O3 y SO2 en vid, maíz, patata, arroz, girasol, tabaco, tomate, sandía y trigo. Los impactos en salud humana han sido modelados como consecuencia de la exposición a PM2,5 y O3 y cuantificados como pérdidas en la esperanza de vida estadística e indicadores de mortalidad prematura. La exactitud del modelo de evaluación integrada ha sido contrastada estadísticamente con los resultados obtenidos por el modelo de calidad del aire convencional, exhibiendo en la mayoría de los casos un buen nivel de correspondencia. Debido a que la cuantificación de los impactos no es llevada a cabo directamente por el modelo de calidad del aire, un análisis de credibilidad ha sido realizado mediante la comparación de los resultados de AERIS con los de GAINS para un escenario de emisiones determinado. El análisis reveló un buen nivel de correspondencia en las medias y en las distribuciones probabilísticas de los conjuntos de datos. Las pruebas de verificación que fueron aplicadas a AERIS sugieren que los resultados son suficientemente consistentes para ser considerados como razonables y realistas. En conclusión, la principal motivación para la creación del modelo fue el producir una herramienta confiable y a la vez simple para el soporte de las partes involucradas en la toma de decisiones, de cara a analizar diferentes escenarios “y si” con un bajo coste computacional. La interacción con políticos y otros actores dictó encontrar un compromiso entre la complejidad del modeladomedioambiental con el carácter conciso de las políticas, siendo esto algo que AERIS refleja en sus estructuras conceptual y computacional. Finalmente, cabe decir que AERIS ha sido creado para su uso exclusivo dentro de un marco de evaluación y de ninguna manera debe ser considerado como un sustituto de los modelos de calidad del aire ordinarios. ABSTRACT Improving air quality is an eminently inter-disciplinary task. The wide variety of sciences and stakeholders that are involved call for having simple yet fully-integrated and reliable evaluation tools available. Integrated AssessmentModeling has proved to be a suitable solution for the description of air pollution systems due to the fact that it considers each of the involved stages: emissions, atmospheric chemistry, dispersion, environmental impacts and abatement potentials. Some integrated assessment models are available at European scale that cover each of the before mentioned stages, being the Greenhouse Gas and Air Pollution Interactions and Synergies (GAINS) model the most recognized and widely-used within a European policy-making context. However, addressing air quality at the national/regional scale under an integrated assessment framework is desirable. To do so, European-scale models do not provide enough spatial resolution or detail in their ancillary data sources, mainly emission inventories and local meteorology patterns as well as associated results. The objective of this dissertation is to present the developments in the design and application of an Integrated Assessment Model especially conceived for Spain and Portugal. The Atmospheric Evaluation and Research Integrated system for Spain (AERIS) is able to quantify concentration profiles for several pollutants (NO2, SO2, PM10, PM2.5, NH3 and O3), the atmospheric deposition of sulfur and nitrogen species and their related impacts on crops, vegetation, ecosystems and health as a response to percentual changes in the emissions of relevant sectors. The current version of AERIS considers 20 emission sectors, either corresponding to individual SNAP sectors or macrosectors, whose contribution to air quality levels, deposition and impacts have been modeled through the use of source-receptor matrices (SRMs). Thesematrices are proportionality constants that relate emission changes with different air quality indicators and have been derived through statistical parameterizations of an air qualitymodeling system (AQM). For the concrete case of AERIS, its parent AQM relied on the WRF model for meteorology and on the CMAQ model for atmospheric chemical processes. The quantification of atmospheric deposition, impacts on ecosystems, crops, vegetation and human health has been carried out following the standard methodologies established under international negotiation frameworks such as CLRTAP. The programming structure isMATLAB ® -based, allowing great compatibility with typical software such as Microsoft Excel ® or ArcGIS ® Regarding air quality levels, AERIS is able to provide mean annual andmean monthly concentration values, as well as the indicators established in Directive 2008/50/EC, namely the 19th highest hourly value for NO2, the 25th highest daily value and the 4th highest hourly value for SO2, the 36th highest daily value of PM10, the 26th highest maximum 8-hour daily value, SOMO35 and AOT40 for O3. Regarding atmospheric deposition, the annual accumulated deposition per unit of area of species of oxidized and reduced nitrogen as well as sulfur can be estimated. When relating the before mentioned values with specific characteristics of the modeling domain such as land use, forest and crops covers, population counts and epidemiological studies, a wide array of impacts can be calculated. When focusing on impacts on ecosystems and soils, AERIS is able to estimate critical load exceedances and accumulated average exceedances for nitrogen and sulfur species. Damage on forests is estimated as an exceedance of established critical levels of NO2 and SO2. Additionally, AERIS is able to quantify damage caused by O3 and SO2 on grapes, maize, potato, rice, sunflower, tobacco, tomato, watermelon and wheat. Impacts on human health aremodeled as a consequence of exposure to PM2.5 and O3 and quantified as losses in statistical life expectancy and premature mortality indicators. The accuracy of the IAM has been tested by statistically contrasting the obtained results with those yielded by the conventional AQM, exhibiting in most cases a good agreement level. Due to the fact that impacts cannot be directly produced by the AQM, a credibility analysis was carried out for the outputs of AERIS for a given emission scenario by comparing them through probability tests against the performance of GAINS for the same scenario. This analysis revealed a good correspondence in the mean behavior and the probabilistic distributions of the datasets. The verification tests that were applied to AERIS suggest that results are consistent enough to be credited as reasonable and realistic. In conclusion, the main reason thatmotivated the creation of this model was to produce a reliable yet simple screening tool that would provide decision and policy making support for different “what-if” scenarios at a low computing cost. The interaction with politicians and other stakeholders dictated that reconciling the complexity of modeling with the conciseness of policies should be reflected by AERIS in both, its conceptual and computational structures. It should be noted however, that AERIS has been created under a policy-driven framework and by no means should be considered as a substitute of the ordinary AQM.

Business, development and inclusive supply chains. Exploring pathways for the sustainable incorporation of the poor as suppliers in agrifood supply chains

El panorama global está cambiando, y esto influye sobre la forma en la que entendemos y tratamos de alcanzar un desarrollo humano sostenible. El crecimiento de la población conlleva una mayor presión sobre los recursos, pero también supone una mayor cantidad de mano de obra y de talento; la concentración en áreas urbanas está cambiando las dinámicas sociales y desafiando los canales de comercialización tradicionales, pero también genera nuevos mercados y fomenta la innovación; los cambios en la economía global están reduciendo los tradicionales desequilibrios de poder entre los países occidentales y el resto del mundo; y las crecientes interconexiones crean nuevos riesgos pero también oportunidades para lanzar iniciativas de alcance global. Todas estas tendencias nos están obligando a repensar qué es el desarrollo humano y de qué manera deberíamos afrontar el reto de la pobreza. Es comúnmente aceptado que la globalización implica interdependencia y que, para conseguir un desarrollo humano sostenible, la colaboración entre actores de distintos ámbitos es necesaria. Se observa una creciente convergencia de temas, intereses y soluciones en torno al desarrollo sostenible, incluso en diferentes países y sectores, lo que está facilitando la colaboración estratégica entre empresas, gobiernos y sociedad civil. Existen pocas duda a día de hoy sobre el papel fundamental que las empresas deben desempeñar en la transición mundial hacia la sostenibilidad ambiental y la erradicación de la pobreza. Las empresas están evolucionando desde un enfoque tradicional centrado en la maximización de beneficios económicos hacia un enfoque holístico que integra la sostenibilidad y la responsabilidad social como parte del núcleo de negocio de las compañías. En el ámbito medioambiental, muchas empresas ya han comenzado a actuar y tratan de reducir sus emisiones, sus desechos y su consumo de energía. Sin embargo la contribución de las empresas a la reducción de la pobreza no está tan clara. Actualmente en torno a 1,2 miles de millones de personas viven en situación de extrema pobreza. La mayoría de estas personas aún vive en zonas rurales donde la mayor parte de la población activa trabaja en el sector agrícola. Por lo tanto, mejorar las oportunidades y reducir los riesgos de los productores más vulnerables en el sector de la agricultura puede ser un motor de desarrollo rural y reducción de la pobreza, especialmente en países de bajo nivel de desarrollo cuyas economías están fundamentalmente basadas en la agricultura. Algunas empresas comienzan a incluir a los pobres en sus operaciones como consumidores, proveedores y emprendedores. Esta tesis se centra en las potenciales oportunidades relacionadas con la incorporación sostenible de los pobres como proveedores de productos y/o de mano de obra. La colaboración entre empresas y productores vulnerables de países en desarrollo es un tema relativamente nuevo y todavía poco estudiado. La pregunta que guía esta tesis es: “¿Cómo pueden las empresas facilitar la inclusión sostenible en cadenas de suministro de productores vulnerables de los países menos desarrollados?”. Para responder a la pregunta anterior, la autora ha aplicado una metodología de casos de estudio. Esta metodología se considera apropiada porque la investigación sobre cadenas de suministro inclusivas es todavía escasa y porque es necesario entender en profundidad un fenómeno de la vida real, y para ello es fundamental conocer su contexto. En primer lugar, se realiza una revisión de literatura para identificar las proposiciones y los constructos teóricos que guiarán la posterior recogida de datos. La revisión de literatura se divide en dos partes: una más general que explora la dimensión social de la sostenibilidad en cadenas de suministro, y una más específica que se centra en la incorporación de los pobres como proveedores en cadenas de suministro. A lo largo de la última década, ha habido un crecimiento exponencial de los estudios académicos sobre la sostenibilidad de las cadenas de suministro, pero la mayoría de los esfuerzos se han dirigido hacia la dimensión medioambiental de la sostenibilidad. Por lo tanto la revisión de literatura, que se presenta en la Sección 3.1 (página 35) y que profundiza en la sostenibilidad social de las cadenas de suministro, puede considerarse una contribución en sí misma. Esta revisión de literatura revela que la investigación sobre aspectos sociales en cadenas de suministro está cobrando impulso en distintas áreas de conocimiento, principalmente en los ámbitos de investigación sobre “gestión de cadenas de suministro”, “responsabilidad social corporativa” y “estudios del desarrollo”. La investigación existente sobre sostenibilidad social de cadenas de suministro se centra en tres temas: aclarar la definición de sostenibilidad social; analizar la implementación de estrategias de sostenibilidad social en cadenas de suministro; y estudiar el apoyo de las em presas líderes a proveedores vulnerables para facilitar su transición hacia la sostenibilidad. Un marco conceptual que resume los principales hallazgos de esta primera parte de la revisión de literatura es planteado en la Figura 7 (página 48). No obstante, en el área de investigación que está emergiendo en torno a la sostenibilidad social de las cadenas de suministro, los estudios relacionados con la reducción de la pobreza son aún escasos. Además se aprecia una falta de contribuciones desde y sobre los países menos desarrollados, así como una clara tendencia a reflejar la visión de las empresas líderes de las cadenas de suministro, olvidando la perspectiva de los proveedores. La segunda parte de la revisión de literatura presentada en la Sección 3.2 (página 51) profundiza en tres líneas de investigación que exploran, desde distintas perspectivas, la inclusión de los pobres en cadenas de suministro. Estas líneas son “Global Value Chains” (GVC), “Base of the Pyramid” (BoP) y “Sustainable Supply Chain Management” (SSCM). La investigación en GVC analiza las cadenas de suministro desde la perspectiva de la globalización económica y el comercio internacional, poniendo especial énfasis en las implicaciones para los países en desarrollo y las comunidades vulnerables. GVC caracteriza las cadenas de suministro según la forma en la que son gobernadas, las oportunidades de mejora que existen para los productores que forman parte de la cadena y el grado de inclusión o exclusión de las comunidades más pobres y vulnerables. La investigación en BoP explora las relaciones comerciales entre empresas y comunidades pobres. La premisa fundamental del concepto BoP es la posibilidad de combinar la generación de beneficios con la reducción de la pobreza. La propuesta original es que mediante la venta de productos y servicios a las comunidades pobres de países en desarrollo, la pobreza puede ser reducida al tiempo que las empresas incrementan sus beneficios, especialmente las grandes empresas multinacionales. Esta idea ha ido evolucionando y, a día de hoy, los investigadores BoP consideran la incorporación de los pobres no sólo como consumidores sino también como empleados, proveedores y co-creadores. La investigación en SSCM ha estado fundamentalmente orientada al estudio de la dimensión medioambiental de la sostenibilidad de cadenas de suministro. Sin embargo, la creciente externalización de la producción a países en desarrollo y las demandas de los grupos de interés para que las empresas aborden todos los aspectos de la sostenibilidad han llevado a los académicos de SSCM a reconocer la importancia de integrar asuntos relacionados con la reducción de la pobreza en sus investigaciones. Algunos estudios comienzan a apuntar los principales retos a los que se enfrentan las empresas para colaborar con productores vulnerables en sus cadenas de suministro. Estos retos son: falta de comunicación, altos costes de transacción y el incremento de la complejidad de las operaciones. Las contribuciones de estas tres líneas de investigación son complementarias para el estudio de las cadenas de suministro inclusivas. Sin embargo, raramente han sido consideradas conjuntamente, ya que pertenecen a ámbitos de conocimiento distintos. Esta tesis integra las aportaciones de GVC, BoP y SSCM en un marco conceptual para la creación y gestión de cadenas de suministro inclusivas. Este marco conceptual para cadenas de suministro inclusivas queda representado en la Figura 9 (página 68). El marco conceptual refleja las motivaciones que llevan a las empresas a colaborar con productores vulnerables, los retos a los que se enfrentan al hacerlo, y los caminos o estrategias que están siguiendo para construir y operar cadenas de suministro inclusivas de manera que sean beneficiosas tanto para la empresa como para los productores vulnerables. A fin de validar y refinar el marco conceptual propuesto, tres casos de estudio se llevan a cabo. Las cadenas de suministro analizadas por los casos de estudio pertenecen al sector agrícola y sus principales proveedores se encuentran en países de África subsahariana. Múltiples métodos de recolección de datos y triangulación son utilizados para mejorar la fiabilidad de los datos. La autora desarrolló trabajos de campo en Senegal, Etiopía y Tanzania. Estos viajes permitieron enriquecer el proceso de recogida de información mediante entrevistas semiestructuradas y conversaciones informales con los principales actores de la cadena de suministro y mediante la observación directa de los procesos y las interacciones entre productores vulnerables y empresas. El Caso de estudio A (Sección 5.1 en página 96) es un caso de estudio único. Analiza la cadena de suministro local de verduras en Senegal. La organización focal es Manobi, una empresa senegalesa que provee servicios de bajo coste a emprendedores locales del sector agrícola. El Caso de estudio A proporciona un interesante análisis del funcionamiento de una cadena de suministro local en un país en desarrollo y muestra como la provisión de servicios profesionales puede mejorar el desempeño de productores vulnerables. El Caso de estudio B (Sección 5.2 en página 122) es un caso de estudio único. Analiza la cadena de suministro global de flor cortada con origen en Etiopía. La organización focal es EHPEA, la Asociación Etíope de Productores y Exportadores Hortícolas, cuya misión es promover y salvaguardar la posición competitiva del sector agrícola etíope en el mercado global. El Caso de estudio B ayuda a comprender mejor la perspectiva de los proveedores respecto a los requerimiento de sostenibilidad del mercado global. También muestra cómo la inclusión de los productores en el proceso de desarrollo de un estándar privado facilita su implementación posterior. El Caso de estudio C (Sección 5.3 en página 143) es un caso de estudio múltiple. Analiza la cadena de suministro global de café especial con origen en Tanzania. Las organizaciones focales son comerciantes que conectan de manera directa a pequeños agricultores de café en países en desarrollo con empresas tostadoras de café en países desarrollados. El Caso de estudio C muestra cómo un pequeño agricultor puede proveer un producto “premium” al mercado global, y participar en un segmento diferenciado del mercado a través de una cadena de suministro transparente y eficiente. Las aportaciones empíricas de los casos de estudio ayudan a validar y mejorar el marco conceptual sobre cadenas de suministro inclusivas (ver discusión en el Capítulo 6 en página 170). El resultado es la propuesta de una nueva versión del marco conceptual representado en la Figura 40 (página 195). Los casos de estudio también proporcionan interesantes aportaciones en relación a la gestión de cadenas de suministro inclusivas y muestran las perspectivas de distintos actores implicados. Esta tesis arroja luz sobre el papel de las empresas en la creación y la gestión de cadenas de suministro inclusivas llevando a cabo una revisión de literatura multidisciplinar y analizando tres casos de estudio en países africanos. Como resultado, esta tesis presenta una serie de contribuciones empíricas y teóricas al ámbito de investigación emergente en torno a las cadenas de suministro inclusivas (Capítulo 7). Esta tesis también pretende ser útil a profesionales que deseen facilitar la incorporación de los pobres como proveedores en condiciones justas y beneficiosas. ABSTRACT The global outlook is changing, and this is influencing the way we understand and try to achieve sustainable human development. Population growth entails increasing pressure over resources, but it also provides greater workforce and talent; concentration in urban areas is changing social dynamics and challenging traditional marketing channels, but also creating news markets and driving innovation; the global economy shift is rebalancing the traditional power imbalance between Western countries and the rest of the world, making new opportunities to arise; and interconnections and global interdependence create new risks but also opportunities for launching initiatives with a global reach. All these trends are impelling us to rethink what development is and in which way poverty alleviation should be approached. It is generally agreed that globalization implies interdependence and, in order to achieve sustainable human development, collaboration of all actors is needed. A convergence of issues, interests and solutions related to sustainable development is being observed across countries and sectors, encouraging strategic collaboration among companies, governments and civil society. There is little doubt nowadays about the crucial role of the private sector in the world’s path towards environmental sustainability and poverty alleviation. Businesses are evolving from a “business as usual” stance to a more sustainable and responsible approach. In the environmental arena, many companies have already “walk the talk”, implementing environmental management systems and trying to reduce emissions and energy consumption. However, regarding poverty alleviation, their contribution is less clear. There are around 1.2 billion people living in extreme poverty. Most of this people still live in rural areas where the agricultural sector employs a big part of the active population. Therefore, improving opportunities and reducing risks for vulnerable producers in the agri-food sector can be a primary engine of rural development and poverty alleviation, particularly in the poor, agriculture-based economies of least developed countries. Some companies are beginning to include the poor into their operations as consumers, suppliers and entrepreneurs. This thesis focuses specifically on the potential opportunities related to the sustainable incorporation of the poor as suppliers of products and/or labor. Business collaboration with vulnerable producers in developing countries is a relatively new trend and it is still understudied. The overall question guiding this thesis is: “How can businesses facilitate the sustainable inclusion of vulnerable producers from least developed countries into supply chains?”. In order to answer the research question, the author has applied a case study research strategy. This methodology is considered appropriate because research about inclusive supply chains is still at an early stage, and because there is a need to understand a real-life phenomenon in depth, but such understanding encompasses important contextual conditions. First, a literature review is conducted, in order to identify the research propositions and theoretical constructs that will guide the data collection. The literature review is divided in two parts: a more general one that explores the social dimension of sustainability of supply chains, and a more specific one that focuses on the incorporation of the poor as suppliers in supply chains. During the last decade, there has been an exponential growth of studies in the field of supply chain sustainability, but research efforts have traditionally been directed towards the analysis of the environmental dimension. Therefore, the literature review presented in Section 3.1 (page 35) that delves into social sustainability of supply chains can be considered a contribution in itself. This literature review reveals that the investigation of social issues in supply chains is gaining momentum and comes from different academic disciplines, namely Supply Chain Management, Corporate Social Responsibility and Development Studies. Existing research about social sustainability of supply chains focuses on three issues: clarify the definition of social sustainability; analyze the implementation of social sustainability strategies in supply chains; and study lead companies’ support to vulnerable suppliers in their transition towards sustainability. A conceptual framework that outlines the main findings that emerge from this first part of literature review is proposed in Figure 7 (page 48). Nevertheless, in this nascent field of social sustainability of supply chains, studies related to poverty alleviation are still scarce. Moreover, a lack of contributions from and about least developed countries has been observed, as well as a tendency to reflect on the lead firms’ standpoint, neglecting the suppliers’ perspective. The second part of the literature review (Section 3.2 in page 51) delves into three research streams that are exploring the inclusion of the poor into supply chains from different viewpoints. These research streams are Global Value Chains (GVC), Base of the Pyramid (BoP) and Sustainable Supply Chain Management (SSCM). GVC research discusses the dynamics of economic globalization and international trade, putting special emphasis in the implications for developing countries and vulnerable communities. GVC characterizes supply chains by the way they are governed, the upgrading opportunities that exist for producers in the chain and the degree of inclusion or exclusion of impoverished communities. BoP research explores trading relationships between businesses and impoverished communities. The core premise of the BoP concept is the possibility to combine profits with poverty alleviation. The original BoP proposition is that by marketing innovative products and services to poor communities in developing countries, poverty would be reduced and companies would increase their benefits, especially multinational companies. This idea has evolved to consider the incorporation of the poor to business activities not only as consumers, but also as employees, entrepreneurs and co-creators. The SSCM school of thought has mainly focused on studying the environmental dimension of supply chain sustainability, neglecting the consideration of the social perspective. However, in recent years, increasing outsourcing of production to developing countries and stakeholders’ demands for a more holistic approach to business sustainability have led SSCM scholars to acknowledge the importance of integrating poverty concerns in this field’s research agenda. Some SSCM studies identify the main operational challenges for companies which engage with vulnerable suppliers in their supply chains: missing communication, higher transactional and operational costs and increased complexity. Contributions from these three research streams are complementary for the study of inclusive supply chains. However, they have been rarely considered together, since they belong to different research areas. This thesis seeks to play a dovetailing role in this scenario by proposing a conceptual framework for creating and operating inclusive supply chains that builds on contributions from GVC, SSCM and BoP research. This framework for inclusive supply chains is depicted in Figure 9 (page 68), and explains the motivations that drive businesses to collaborate with vulnerable suppliers, the chal lenges they face in doing so, and the pathways they are following in order to build and operate inclusive supply chains profitably for both buying companies and vulnerable suppliers. In order to validate and refine the proposed framework, three case studies are carried out. The supply chains analyzed by the case studies belong to the agri-food sector and source from Sub-Saharan African countries. Multiple data collection methods and triangulation are used in order to improve reliability of findings. The author carried out field work in Senegal, Ethiopia and Tanzania. These travels enriched the data collection process, providing semi-structured interviews and informal conversations with the main actors in the supply chains, as well as direct observation of processes and interactions among companies and vulnerable suppliers. Case study A (Section 5.1 in page 96) is a single case study. It analyzes a local supply chain in Senegal providing vegetables to the local market. The focal organization is Manobi, a Senegalese inclusive business which provides affordable ICT services to local entrepreneurs in the agri-food sector. Case study A provides interesting insights into the dynamics of local supply chains and how professional services can help to improve their performance. Case study B (Section 5.2 in page 122) is a single case study. It analyzes a global supply chain with origin in Ethiopia providing cut flowers to the global commodity market. The focal organization is EHPEA, Ethiopian Horticulture Producers and Exporters Association, whose mission is to promote and safeguard the competitive position of the Ethiopian horticulture sector within the global market. Case study B helps to better understand the suppliers’ perspective regarding global market sustainability requirements and shows how the inclusion of suppliers in the process of development of a private standard has a positive impact in its implementation. Case study C (Section 5.3 in page 143) is a multiple case study. It analyzes a global supply chain with origin in Tanzania providing coffee to the global niche market of specialty coffee. The focal organizations are traders who are directly connecting smallholder coffee farmers in developing countries to coffee roasters in developed countries. Case study C shows how smallholder farmers can supply a premium product and be incorporated in a differentiated market segment through a transparent and efficient supply chain. The empirical findings from the case studies help to validate and refine the conceptual framework (see discussion in Chapter 6). The proposal of a new version of the conceptual framework is depicted in Figure 40 (page 195). The case studies also provide interesting insights related to the management of inclusive supply chains and show the perspectives of the different actors involved. This thesis sheds some light on the role of businesses in the creation and operation of inclusive supply chains by carrying out a cross-disciplinary literature review and analyzing three case studies in African countries. In doing so, this thesis presents a series of theoretical and empirical contributions to the emerging academic field of inclusive supply chains (Chapter 7). This thesis also intends to be useful to practitioners willing to improve the incorporation of the poor as suppliers in fair and profitable conditions.

Development and Testing of a Fiber Bragg Grating Strain Sensor for Uniaxial Compression of Rock Specimens

Los sensores de fibra óptica son una tecnología que ha madurado en los últimos años, sin embargo, se requiere un mayor desarrollo de aplicaciones para materiales naturales como las rocas, que por ser agregados complejos pueden contener partículas minerales y fracturas de tamaño mucho mayor que las galgas eléctricas usadas tradicionalmente para medir deformaciones en las pruebas de laboratorio, ocasionando que los resultados obtenidos puedan ser no representativos. En este trabajo fueron diseñados, fabricados y probados sensores de deformación de gran área y forma curvada, usando redes de Bragg en fibra óptica (FBG) con el objetivo de obtener registros representativos en rocas que contienen minerales y estructuras de diversas composiciones, tamaños y direcciones. Se presenta el proceso de elaboración del transductor, su caracterización mecánica, su calibración y su evaluación en pruebas de compresión uniaxial en muestras de roca. Para verificar la eficiencia en la transmisión de la deformación de la roca al sensor una vez pegado, también fue realizado el análisis de la transferencia incluyendo los efectos del adhesivo, de la muestra y del transductor. Los resultados experimentales indican que el sensor desarrollado permite registro y transferencia de la deformación fiables, avance necesario para uso en rocas y otros materiales heterogénos, señalando una interesante perspectiva para aplicaciones sobre superficies irregulares, pues permite aumentar a voluntad el tamaño y forma del área de registro, posibilita también obtener mayor fiabilidad de resultados en muestras de pequeño tamaño y sugiere su conveniencia en obras, en las cuales los sistemas eléctricos tradicionales tienen limitaciones. ABSTRACT Optical fiber sensors are a technology that has matured in recent years, however, further development for rock applications is needed. Rocks contain mineral particles and features larger than electrical strain gauges traditionally used in laboratory tests, causing the results to be unrepresentative. In this work were designed, manufactured, and tested large area and curved shape strain gages, using fiber Bragg gratings in optical fiber (FBG) in order to obtain representative measurement on surface rocks samples containing minerals and structures of different compositions, sizes and directions. This reports presents the processes of manufacturing, mechanical characterization, calibration and evaluation under uniaxial compression tests on rock samples. To verify the efficiency of rock deformation transmitted to attached sensor, it was also performed the analysis of the strain transfer including the effects of the bonding, the sample and the transducer. The experimental results indicate that the developed sensor enables reliable measurements of the strain and its transmission from rock to sensor, appropriate for use in heterogeneous materials, pointing an interesting perspective for applications on irregular surfaces, allowing increasing at will the size and shape of the measurement area. This research suggests suitability of the optical strain gauge for real scale, where traditional electrical systems have demonstrated some limitations.

Instruments for analysing urban conflicts in the Global South: The case of urban transformation processes in Dakar

Physical and social transformation processes that take place in urban contexts with strong spatial growth and hardly any economic development frequently have significant adverse impacts for the affected people, which tend to be made invisible. This paper presents an analytical framework to explore different ways to approach urban transformation processes (supply side), their impacts on the set of needs of the community (demand side) and their consequences on the urban environment as a whole (context). The proposed method has been used to assess three actions related to the physical and social transformation of the largest self-made settlement in the city of Dakar, Senegal, during the 2005–2012 period. Research findings show how exogenous interests are privileged over the common good when the affected citizens are not effectively involved in decision-making processes.

Development of a sensorimotor algorithm able to deal with unforeseen pushes and its implementation based on VHDL

Development of a Sensorimotor Algorithm Able to Deal with Unforeseen Pushes and Its Implementation Based on VHDL is the title of my thesis which concludes my Bachelor Degree in the Escuela Técnica Superior de Ingeniería y Sistemas de Telecomunicación of the Universidad Politécnica de Madrid. It encloses the overall work I did in the Neurorobotics Research Laboratory from the Beuth Hochschule für Technik Berlin during my ERASMUS year in 2015. This thesis is focused on the field of robotics, specifically an electronic circuit called Cognitive Sensorimotor Loop (CSL) and its control algorithm based on VHDL hardware description language. The reason that makes the CSL special resides in its ability to operate a motor both as a sensor and an actuator. This way, it is possible to achieve a balanced position in any of the robot joints (e.g. the robot manages to stand) without needing any conventional sensor. In other words, the back electromotive force (EMF) induced by the motor coils is measured and the control algorithm responds depending on its magnitude. The CSL circuit contains mainly an analog-to-digital converter (ADC) and a driver. The ADC consists on a delta-sigma modulation which generates a series of bits with a certain percentage of 1's and 0's, proportional to the back EMF. The control algorithm, running in a FPGA, processes the bit frame and outputs a signal for the driver. This driver, which has an H bridge topology, gives the motor the ability to rotate in both directions while it's supplied with the power needed. The objective of this thesis is to document the experiments and overall work done on push ignoring contractive sensorimotor algorithms, meaning sensorimotor algorithms that ignore large magnitude forces (compared to gravity) applied in a short time interval on a pendulum system. This main objective is divided in two sub-objectives: (1) developing a system based on parameterized thresholds and (2) developing a system based on a push bypassing filter. System (1) contains a module that outputs a signal which blocks the main Sensorimotor algorithm when a push is detected. This module has several different parameters as inputs e.g. the back EMF increment to consider a force as a push or the time interval between samples. System (2) consists on a low-pass Infinite Impulse Response digital filter. It cuts any frequency considered faster than a certain push oscillation. This filter required an intensive study on how to implement some functions and data types (fixed or floating point data) not supported by standard VHDL packages. Once this was achieved, the next challenge was to simplify the solution as much as possible, without using non-official user made packages. Both systems behaved with a series of interesting advantages and disadvantages for the elaboration of the document. Stability, reaction time, simplicity or computational load are one of the many factors to be studied in the designed systems. RESUMEN. Development of a Sensorimotor Algorithm Able to Deal with Unforeseen Pushes and Its Implementation Based on VHDL es un Proyecto de Fin de Grado (PFG) que concluye mis estudios en la Escuela Técnica Superior de Ingeniería y Sistemas de Telecomunicación de la Universidad Politécnica de Madrid. En él se documenta el trabajo de investigación que realicé en el Neurorobotics Research Laboratory de la Beuth Hochschule für Technik Berlin durante el año 2015 mediante el programa de intercambio ERASMUS. Este PFG se centra en el campo de la robótica y en concreto en un circuito electrónico llamado Cognitive Sensorimotor Loop (CSL) y su algoritmo de control basado en lenguaje de modelado hardware VHDL. La particularidad del CSL reside en que se consigue que un motor haga las veces tanto de sensor como de actuador. De esta manera es posible que las articulaciones de un robot alcancen una posición de equilibrio (p.ej. el robot se coloca erguido) sin la necesidad de sensores en el sentido estricto de la palabra. Es decir, se mide la propia fuerza electromotriz (FEM) inducida sobre el motor y el algoritmo responde de acuerdo a su magnitud. El circuito CSL se compone de un convertidor analógico-digital (ADC) y un driver. El ADC consiste en un modulador sigma-delta, que genera una serie de bits con un porcentaje de 1's y 0's determinado, en proporción a la magnitud de la FEM inducida. El algoritmo de control, que se ejecuta en una FPGA, procesa esta cadena de bits y genera una señal para el driver. El driver, que posee una topología en puente H, provee al motor de la potencia necesaria y le otorga la capacidad de rotar en cualquiera de las dos direcciones. El objetivo de este PFG es documentar los experimentos y en general el trabajo realizado en algoritmos Sensorimotor que puedan ignorar fuerzas de gran magnitud (en comparación con la gravedad) y aplicadas en una corta ventana de tiempo. En otras palabras, ignorar empujones conservando el comportamiento original frente a la gravedad. Para ello se han desarrollado dos sistemas: uno basado en umbrales parametrizados (1) y otro basado en un filtro de corte ajustable (2). El sistema (1) contiene un módulo que, en el caso de detectar un empujón, genera una señal que bloquea el algoritmo Sensorimotor. Este módulo recibe diferentes parámetros como el incremento necesario de la FEM para que se considere un empujón o la ventana de tiempo para que se considere la existencia de un empujón. El sistema (2) consiste en un filtro digital paso-bajo de respuesta infinita que corta cualquier variación que considere un empujón. Para crear este filtro se requirió un estudio sobre como implementar ciertas funciones y tipos de datos (coma fija o flotante) no soportados por las librerías básicas de VHDL. Tras esto, el objetivo fue simplificar al máximo la solución del problema, sin utilizar paquetes de librerías añadidos. En ambos sistemas aparecen una serie de ventajas e inconvenientes de interés para el documento. La estabilidad, el tiempo de reacción, la simplicidad o la carga computacional son algunas de las muchos factores a estudiar en los sistemas diseñados. Para concluir, también han sido documentadas algunas incorporaciones a los sistemas: una interfaz visual en VGA, un módulo que compensa el offset del ADC o la implementación de una batería de faders MIDI entre otras.