The effect of heat treatment on the toughness, hardness and microstructure of low carbon white cast irons

The effect of destabilisation and subcritical heat treatment on the impact toughness, hardness, and the amount and mechanical stability of retained austenite in a low carbon white cast iron have been investigated. The experimental results show that the impact energy constantly increases when the destabilisation temperature is raised from 950 degreesC to 1200 degreesC. Although the hardness decreases, the heat-treated hardness is still greater than the as-cast state. After destabilisation treatment at 1130 degreesC, tempering at 200 to 250 degreesC for 3 hours leads to the highest impact toughness, and secondary hardening was observed when tempering over 400 degreesC. The amount of retained austenite increased with the increase in the destabilisation temperature, and the treatment significantly improves the mechanical stability of the retained austenite compared with the as-cast state. Tempering below 400 degreesC does not affect the amount of retained austenite and its mechanical stability. But the amount of retained austenite is dramatically reduced when tempered above 400 degreesC. The relationship between the mechanical properties and the microstructure changes was discussed. (C) 2001 Kluwer Academic Publishers.

Integrated treatment of shrimp effluent by sedimentation, oyster filtration and macroalgal absorption: a laboratory scale study

Effluent water from shrimp ponds typically contains elevated concentrations of dissolved nutrients and suspended particulates compared to influent water. Attempts to improve effluent water quality using filter feeding bivalves and macroalgae to reduce nutrients have previously been hampered by the high concentration of clay particles typically found in untreated pond effluent. These particles inhibit feeding in bivalves and reduce photosynthesis in macroalgae by increasing effluent turbidity. In a small-scale laboratory study, the effectiveness of a three-stage effluent treatment system was investigated. In the first stage, reduction in particle concentration occurred through natural sedimentation. In the second stage, filtration by the Sydney rock oyster, Saccostrea commercialis (Iredale and Roughley), further reduced the concentration of suspended particulates, including inorganic particles, phytoplankton, bacteria, and their associated nutrients. In the final stage, the macroalga, Gracilaria edulis (Gmelin) Silva, absorbed dissolved nutrients. Pond effluent was collected from a commercial shrimp farm, taken to an indoor culture facility and was left to settle for 24 h. Subsamples of water were then transferred into laboratory tanks stocked with oysters and maintained for 24 h, and then transferred to tanks containing macroalgae for another 24 h. Total suspended solid (TSS), chlorophyll a, total nitrogen (N), total phosphorus (P), NH4+, NO3-, and PO43-, and bacterial numbers were compared before and after each treatment at: 0 h (initial); 24 h (after sedimentation); 48 h (after oyster filtration); 72 h (after macroalgal absorption). The combined effect of the sequential treatments resulted in significant reductions in the concentrations of all parameters measured. High rates of nutrient regeneration were observed in the control tanks, which did not contain oysters or macroalgae. Conversely, significant reductions in nutrients and suspended particulates after sedimentation and biological treatment were observed. Overall, improvements in water quality (final percentage of the initial concentration) were as follows: TSS (12%); total N (28%); total P (14%); NH4+ (76%); NO3- (30%); PO43-(35%); bacteria (30%); and chlorophyll a (0.7%). Despite the probability of considerable differences in sedimentation, filtration and nutrient uptake rates when scaled to farm size, these results demonstrate that integrated treatment has the potential to significantly improve water quality of shrimp farm effluent. (C) 2001 Elsevier Science B.V. All rights reserved.

Treatment outcome in individuals with chronic pain: is the Pain Stages of Change Questionnaire (PSOCQ) a useful tool? Jenny StrongCorresponding Author Contact Information, E-mail The Corresponding Author, a, Kym Westburya, Glen Smithb, Ian McKenziec and William Ryan

The efficacy of psychological treatments emphasising a self-management approach to chronic pain has been demonstrated by substantial empirical research. Nevertheless, high drop-out and relapse rates and low or unsuccessful engagement in self-management pain rehabilitation programs have prompted the suggestion that people vary in their readiness to adopt a self-management approach to their pain. The Pain Stages of Change Questionnaire (PSOCQ) was developed to assess a patient's readiness to adopt a self-management approach to their chronic pain. Preliminary evidence has supported the PSOCQ's psychometric properties. The current study was designed to further examine the psychometric properties of the PSOCQ, including its reliability, factorial structure and predictive validity. A total of 107 patients with an average age of 36.2 years (SD = 10.63) attending a multi-disciplinary pain management program completed the PSOCQ, the Pain Self-Efficacy Questionnaire (PSEQ) and the West Haven-Yale Multidimensional Pain Inventory (WHYMPI) pre-admission and at discharge from the program. Initial data analysis found inadequate internal consistencies of the precontemplation and action scales of the PSOCQ and a high correlation (r = 0.66, P < 0.01) between the action and maintenance scales. Principal component analysis supported a two-factor structure: 'Contemplation' and 'Engagement'. Subsequent analyses revealed that the PSEQ was a better predictor of treatment outcome than the PSOCQ scales. Discussion centres upon the utility of the PSOCQ in a clinical pain setting in light of the above findings, and a need for further research. (C) 2002 International Association for the Study of Pain. Published by Elsevier Science B.V. All rights reserved.

Disease, habitat fragmentation and conservation

Habitat loss and the resultant fragmentation of remaining habitat is the primary cause of loss of biological diversity. How do these processes affect the dynamics of parasites and pathogens? Hess has provided some important insights into this problem using metapopulation models for pathogens that exhibit 'S-I' dynamics; for example, pathogens such as rabies in which the host population may be divided into susceptible and infected individuals. A major assumption of Hess's models is that infected patches become extinct, rather than recovering and becoming resistant to future infections. In this paper, we build upon this framework in two different ways: first, we examine the consequences of including patches that are resistant to infection; second, we examine the consequences of including a second species of host that can act as a reservoir for the pathogen. Both of these effects are likely to be important from a conservation perspective. The results of both sets of analysis indicate that the benefits of corridors and other connections that allow species to disperse through the landscape far outweigh the possible risks of increased pathogen transmission. Even in the commonest case, where harmful pathogens are maintained by a common reservoir host, increased landscape connectance still allows greater coexistence and persistence of a threatened or endangered host.

Towards the on-farm conservation of the assassin bug Pristhesancus plagipennis (Walker) (Hemiptera : Reduviidae) during winter using crop plants as refuges

Habitat instability associated with seasonal crop succession in broad-acre farming systems presents a problem for the conservation and utilisation of beneficial insects in annual field crops. The present paper describes two experiments used to measure the potential of seven plant species to be utilised as winter refuges to support and conserve the predatory bug Pristhesancus plagipennis (Walker). In the first experiment, replicated plots of canola (Brassica napus ), red salvia (Salvia coccinea ), niger (Guizotia abyssinica ), linseed (Linum usitatissimum ), lupins (Lupinus angustifolius ), and lucerne (Medicago falcata ) were planted in a randomized experiment during Autumn 1998. Upon crop establishment, adults and nymphs of P. plagipennis were released into treatment plots and their numbers were assessed, along with those of their potential prey, throughout the ensuing winter months. Post-release sampling suggested that canola and niger retained a proportion of adult P. plagipennis , while niger, lucerne and canola retained some nymphs. The other plant species failed to support P. plagipennis nymphs and adults postrelease. In the second experiment, niger was compared with two lines of sunflower (Helianthus annus ). Both sunflower lines harboured significantly higher (P < 0.05) densities of P. plagipennis nymphs than did niger. The more successful refuge treatments (sunflower, niger and canola) had an abundance of yellow flowers that were attractive to pollinating insects, which served as supplementary prey on which P. plagipennis were observed to feed. Sunflower and niger also supported high densities of the prey insect Creontiades dilutus (Stal) and provided protective leafy canopies which supplied shelter during the winter months. The potential and limitations for using each plant species as a winter refuge to retain P. plagipennis during winter are discussed.

Chemical treatment of papaya seeds aiming at long-term storage and control of damping off

Damping off is a nursery disease of great economic importance in papaya and seed treatment may be an effective measure to control. The aim of this work was to evaluate the quality of papaya seeds treated with fungicides and stored under two environmental and packaging conditions. Additionally, the efficiency of fungicide treatments in the control of damping-off caused by Rhizoctonia solani was evaluated. Papaya seeds were treated with the fungicides Captan, Tolylfluanid and the mixture Tolylfluanid + Captan (all commercial wettable powder formulations). Seeds of the control group were not treated. The seeds were stored for nine months in two conditions: packed in aluminum coated paper and kept at 7 ± 1ºC and in permeable kraft paper and kept in non-controlled environment. At the beginning of the storage and every three months the seed quality (germination and vigor tests), emergence rate index, height, dry mass and damping of plants in pre and post-emergence (in contaminated substrate and mycelia-free substrate) were analyzed. Both storage conditions as well as the fungicide treatments preserved the germination and seed vigor. In the infested substrate, seedling emergence was favored by fungicides, but in post-emergence, fungicides alone did not control the damping off caused by R. solani. Symptoms of damping off were not observed in the clean substrate. The results showed that the fungicide treatments may be used to pretreat papaya seed for long-term storage and commercialization.

Biology, ecology and conservation of mobulid rays in the Azores

Dissertação de Mestrado, Estudos Integrados dos Oceanos, 12 de Dezembro de 2013, Universidade dos Açores.

Mapping and characterization of a green biofilm inside of Vilar de Frades Church (Portugal)

Vilar de Frades church is integrated in the Vilar de Frades Monastery, located in the North part of Portugal (Barcelos). The monastery, founded in 566, suffered several architectural modifications and restoration works, the most relevant was in the XVI century. The church, in granite, has one nave and six bays,holding ten chapels with vaults of crossed ribbings. Nowadays, the chapels present a severe biological colonization characterised by an intense green biofilm, which becoming apparent in other locations inside the church. In the course of a general survey concerning the conservation state of the church, an accurate campaign was planned in order to assess the main biodeterioration agents, map biological colonization and determine the environmental conditions. Laboratory analyses were accomplished with optical microscopy and spectrofluorometry. This study presents the results of this campaign. Details on conservation or preservation works that need to be implemented are also presented.

AMERICAN CUTANEOUS LEISHMANIASIS WITH UNUSUAL CLINICAL PRESENTATION AND RESPONSE TO TREATMENT

The clinical manifestations and prognosis of cutaneous leishmaniasis (CL) can be influenced by the immune response of the patient and the species of the parasite. A case of atypical clinical presentation of CL, with development of non-characteristic lesions, poor response to therapy, and a long time to resolution is reported. Confirmatory laboratory tests included parasite detection, indirect immunofluorescence, Montenegro skin test, polymerase chain reaction, and parasite identification by multilocus enzyme electrophoresis. The parasite was identified as Leishmaniabraziliensis. The lesion was unresponsive to three complete courses of N-methylglucamine antimoniate intramuscular, and to treatment with pentamidine. The patient did not tolerate amphotericin B. The lesion finally receded after treatment with intravenous N-methylglucamine antimoniate. It is essential to ensure the accuracy of diagnosis and the appropriate treatment, which can include the use a second choice drug or a different route of administration.

The Oncological and Functional Risks of the Organ Preservation Experimental Treatment Approach

We increasingly face conservative surgery for rectal cancer and even the so called ‘wait and see’ approach, as far as 10–20% patients can reach a complete pathological response at the time of surgery. But what can we say to our patients about risks? Standard surgery with mesorectal excision gives a <2% local recurrence with a post operative death rate of 2–8% (may reach 30% at 6 months in those over 85), but low AR has some deterioration in bowel function and in low cancer a permanent stoma may be required. Also a long-term impact on urinary and sexual function is possible. Distant metastasis rate seem to be identical in the standard and conservative approach. It is difficult to evaluate conservative approach because a not clear standardization of surgery for low rectal cancer. Rullier et al tried to clarify, and they found identical results for recurrence (5–9%), disease free survival (70%) at 5y for coloanal anastomosis and intersphinteric resection. Other series have found local recurrence higher than with standard approach and functional results may be worse and, in some situations, salvage therapy is compromised or has more complications. In this context, functional outcomes are very important but most studies are incomplete in measuring bowel function in the context of conservative approach. In 2005 Temple et al made a survey of 122/184 patient after sphinter preserving surgery and found a 96.9% of incomplete evacuation, 94.4% clustering, 93.2% food affecting frequency, 91.8% gas incontinence and proposed a systematic evaluation with a specific questionnaire. In which concerns ‘Wait and see’ approach for complete clinical responders, it was first advocated by Habr Gama for tumors up to 7cm, with a low locoregional failure of 4.6%, 5y overall survival 96%, 72% for disease free survival; one fifth of patients failed in the first year; a Dutch trial had identical results but others had worse recurrence rates; in other series 25% of patients could not be salvaged even with APR; 30% have subsequent metastatic disease what seems equal for ‘wait and see’ and operated patients. In a recent review Glynne Jones considers that all the evaluated ‘wait and see’ studies are heterogeneous in staging, inclusion criteria, design and follow up after chemoradiation and that there is the suggestion that patients who progress while under observation fare worse than those resected. He proposes long-term observational studies with more uniform inclusion criteria. We are now facing a moment where we may be more aggressive in early cancer and neoadjuvant treatment to be more conservative in the subsequent treatment but we need a better stratification of patients, better evaluation of results and more clear prognostic markers.

Unstabilised rammed earth: characterization of material collected from old constructions in South Portugal and comparison to normative requirements

International Journal of Architectural Heritage, 8: 185–212, 2014

Analysis, testing and development of safe cleaning methods of rusted stone material

Three different treatments were applied on several specimens of dolomitic and calcitic marble, properly stained with rust to mimic real situations (the stone specimens were exposed to the natural environment for about six months in contact with rusted iron). Thirty six marble specimens, eighteen calcitic and eighteen dolomitic, were characterized before and after treatment and monitored throughout the cleaning tests. The specimens were characterized by SEM-EDS (Scanning Electron Microscopy coupled with Energy Dispersion System), XRD (XRay Diffraction), XRF (X-Ray Fluorescence), FTIR (Fourier Transform Infrared Spectroscopy) and color measurements. It was also made a microscopic and macroscopic analysis of the stone surface along with the tests of short and long term capillary absorption. A series of test trials were conducted in order to understand which concentrations and contact times best suits to this purpose, to confirm what had been written to date in the literature. We sought to develop new methods of treatment application, skipping the usual methods of applying chemical treatments on stone substrates, with the use of cellulose poultice, resorting to the agar, a gel already used in many other areas, being something new in this area, which possesses great applicability in the field of conservation of stone materials. After the application of the best methodology for cleaning, specimens were characterized again in order to understand which treatment was more effective and less harmful, both for the operator and the stone material. Very briefly conclusions were that for a very intense and deep penetration into the stone, a solution of 3.5% of SDT buffered with ammonium carbonate to pH around 7 applied with agar support would be indicated. For rust stains in its initial state, the use of Ammonium citrate at a concentration of 5% buffered with ammonium to pH 7 could be applied more than once until satisfactory results appear.

Characterization of physical, mechanical and chemical properties of quiscal fibres : the influence of atmospheric DBD plasma treatment

This paper reports the first attempt of characterizing various physical, mechanical and chemical properties of Quiscal fibres, used by the native communities in Chile and investigating the influence of atmospheric dielectric barrier discharge plasma treatment on various properties such as diameter and linear density, fat, wax and impurity%, moisture regain, chemical elements and groups, thermal degradation, surface morphology, etc. According to the experimental observations, Quiscal fibre has lower tenacity than most of the technical grade natural fibres such as sisal, hemp, flax, etc., and plasma treatment at optimum dose improved its tenacity to the level of sisal fibres. Plasma treatment also reduced the amount of fat, wax and other foreign impurities present in Quiscal fibres as well as removed lignin and hemicellulose partially from the fibre structure. Plasma treatment led to functionalization of Quiscal fibre surface with chemical groups, as revealed from attenuated total reflection spectroscopy and also confirmed from the elemental analysis using energy dispersive Xray technique and pH and conductivity measurements of fibre aqueous extract. The wetting behavior of Quiscal fibre also improved considerably through plasma treatment. However, untreated and plasma treated Quiscal fibres showed similar thermal degradation behavior, except the final degradation stage, in which plasma treated fibres showed higher stability and incomplete degradation unlike the untreated fibres. The experimental results suggested that the plasma treated Quiscal fibres, like other technical grade natural fibres, can find potential application as reinforcement of composite materials for various industrial applications.