Applications of High Speed Configurable Logic Devices in Modern Particle Physics Experiments

Several activities were conducted during my PhD activity. For the NEMO experiment a collaboration between the INFN/University groups of Catania and Bologna led to the development and production of a mixed signal acquisition board for the Nemo Km3 telescope. The research concerned the feasibility study for a different acquisition technique quite far from that adopted in the NEMO Phase 1 telescope. The DAQ board that we realized exploits the LIRA06 front-end chip for the analog acquisition of anodic an dynodic sources of a PMT (Photo-Multiplier Tube). The low-power analog acquisition allows to sample contemporaneously multiple channels of the PMT at different gain factors in order to increase the signal response linearity over a wider dynamic range. Also the auto triggering and self-event-classification features help to improve the acquisition performance and the knowledge on the neutrino event. A fully functional interface towards the first level data concentrator, the Floor Control Module, has been integrated as well on the board, and a specific firmware has been realized to comply with the present communication protocols. This stage of the project foresees the use of an FPGA, a high speed configurable device, to provide the board with a flexible digital logic control core. After the validation of the whole front-end architecture this feature would be probably integrated in a common mixed-signal ASIC (Application Specific Integrated Circuit). The volatile nature of the configuration memory of the FPGA implied the integration of a flash ISP (In System Programming) memory and a smart architecture for a safe remote reconfiguration of it. All the integrated features of the board have been tested. At the Catania laboratory the behavior of the LIRA chip has been investigated in the digital environment of the DAQ board and we succeeded in driving the acquisition with the FPGA. The PMT pulses generated with an arbitrary waveform generator were correctly triggered and acquired by the analog chip, and successively they were digitized by the on board ADC under the supervision of the FPGA. For the communication towards the data concentrator a test bench has been realized in Bologna where, thanks to a lending of the Roma University and INFN, a full readout chain equivalent to that present in the NEMO phase-1 was installed. These tests showed a good behavior of the digital electronic that was able to receive and to execute command imparted by the PC console and to answer back with a reply. The remotely configurable logic behaved well too and demonstrated, at least in principle, the validity of this technique. A new prototype board is now under development at the Catania laboratory as an evolution of the one described above. This board is going to be deployed within the NEMO Phase-2 tower in one of its floors dedicated to new front-end proposals. This board will integrate a new analog acquisition chip called SAS (Smart Auto-triggering Sampler) introducing thus a new analog front-end but inheriting most of the digital logic present in the current DAQ board discussed in this thesis. For what concern the activity on high-resolution vertex detectors, I worked within the SLIM5 collaboration for the characterization of a MAPS (Monolithic Active Pixel Sensor) device called APSEL-4D. The mentioned chip is a matrix of 4096 active pixel sensors with deep N-well implantations meant for charge collection and to shield the analog electronics from digital noise. The chip integrates the full-custom sensors matrix and the sparsifification/readout logic realized with standard-cells in STM CMOS technology 130 nm. For the chip characterization a test-beam has been set up on the 12 GeV PS (Proton Synchrotron) line facility at CERN of Geneva (CH). The collaboration prepared a silicon strip telescope and a DAQ system (hardware and software) for data acquisition and control of the telescope that allowed to store about 90 million events in 7 equivalent days of live-time of the beam. My activities concerned basically the realization of a firmware interface towards and from the MAPS chip in order to integrate it on the general DAQ system. Thereafter I worked on the DAQ software to implement on it a proper Slow Control interface of the APSEL4D. Several APSEL4D chips with different thinning have been tested during the test beam. Those with 100 and 300 um presented an overall efficiency of about 90% imparting a threshold of 450 electrons. The test-beam allowed to estimate also the resolution of the pixel sensor providing good results consistent with the pitch/sqrt(12) formula. The MAPS intrinsic resolution has been extracted from the width of the residual plot taking into account the multiple scattering effect.

Noisy Oncology: applications of bounded noise transitions in modelling tumor growth

I tumori macroscopici e microscopici, dopo la loro prima fase di crescita, sono composti da un numero medio elevato di cellule. Così, in assenza di perturbazioni esterne, la loro crescita e i punti di equilibrio possono essere descritti da equazioni differenziali. Tuttavia, il tumore interagisce fortemente col macroambiente che lo circonda e di conseguenza una descrizione del tutto deterministica risulta a volte inappropriata. In questo caso si può considerare l'interazione con fluttuazioni statistiche, causate da disturbi esterni, utilizzando le equazioni differenziali stocastiche (SDE). Questo è vero in modo particolare quando si cerca di modellizzare tumori altamente immunogenici che interagiscono con il sistema immunitario, in quanto la complessità di questa interazione risulta in fenomeni di multistabilità. Così, il rumore può provocare disturbi e indurre transizioni di stato (Noise-Induced-Transitions). E' importante notare che una NIT può avere implicazioni profonde sulla vita di un paziente, dal momento che una transizione da uno stato di equilibrio piccolo, nelle dimensioni del tumore, ad uno stato di equilibrio macroscopico, nella maggior parte dei casi significa il passaggio dalla vita alla morte. Generalmente l'approccio standard è quello di modellizzare le fluttuazioni stocastiche dei parametri per mezzo di rumore gaussiano bianco o colorato. In alcuni casi però questa procedura è altamente inadeguata, a causa della illimitatezza intrinseca dei rumori gaussiani che può portare a gravi incongruenze biologiche: pertanto devono essere utilizzati dei rumori "limitati", che, tuttavia, sono molto meno studiati di quelli gaussiani. Inoltre, l'insorgenza di NIT dipende dal tipo di rumore scelto, che rivela un nuovo livello di complessità in biologia. Lo scopo di questa tesi è quello di studiare le applicazioni di due tipi diversi di "rumori limitati" nelle transizioni indotte in due casi: interazione tra tumore e sistema immunitario e chemioterapia dei tumori. Nel primo caso, abbiamo anche introdotto un nuovo modello matematico di terapia, che estende, in modo nuovo, il noto modello di Norton-Simon.

Advanced applications of X-ray Absorption Spectroscopy to the study of protein metal sites.

We present a study of the metal sites of different proteins through X-ray Absorption Fine Structure (XAFS) spectroscopy. First of all, the capabilities of XAFS analysis have been improved by ab initio simulation of the near-edge region of the spectra, and an original analysis method has been proposed. The method subsequently served ad a tool to treat diverse biophysical problems, like the inhibition of proton-translocating proteins by metal ions and the matrix effect exerted on photosynthetic proteins (the bacterial Reaction Center, RC) by strongly dehydrate sugar matrices. A time-resolved study of Fe site of RC with μs resolution has been as well attempted. Finally, a further step aimed to improve the reliability of XAFS analysis has been performed by calculating the dynamical parameters of the metal binding cluster by means of DFT methods, and the theoretical result obtained for MbCO has been successfully compared with experimental data.

Extraterrestrial and terrestrial outdoor applications of Mössbauer spectroscopy

„Extraterrestrische und terrestrische Anwendungen eines miniaturisierten Mössbauer-Spektrometers“ Die vorliegende Arbeit befasst sich mit Anwendungen eines miniaturisierten Mössbauer- Spektrometers (MIMOS II), dessen Entwicklung in den frühen neunziger Jahren am Institut für Kernphysik der Technischen Universität Darmstadt unter Professor Egbert Kankeleit und seinen Mitarbeitern begann. Seit 1998 sind die Entwicklungsarbeiten im Arbeitskreis von Prof. Gütlich am Institut für Anorganische und Analytische Chemie der Johannes Gutenberg- Universität Mainz von Dr. Göstar Klingelhöfer und Mitarbeitern fortgesetzt worden. Vorrangiges Ziel war dabei der geplante Einsatz des Spektrometers zu mineralogischen Untersuchungen im Weltall. Entsprechend ist das Projekt mit erheblichen finanziellen Mitteln des Forschungsinstituts der Deutschen Luft- und Raumfahrt (DLR) in Bonn unterstützt worden. Bei den beiden Missionen, die im Jahre 2003 von der NASA zum Mars gesandt wurden und im Januar dieses Jahres die beiden „Mars Exploration Rover“ (MER) "Spirit" und "Opportunity" erfolgreich auf der Marsoberfläche abgesetzt haben, ist jeweils ein MIMOS II-Gerät zur Charakterisierung eisenhaltiger Minerale und Böden während der laufenden Mission im Einsatz. Einige Ergebnisse von MIMOS II an Gestein und Böden der Marsoberfläche werden in der vorliegenden Arbeit präsentiert und diskutiert. Diese Ergebnisse wurden vom MIMOS II-Consortium unter Führung von Dr. Göstar Klingelhöfer, mit Unterstützung des Ingenieurs- und Wissenschaftsteams von MER am Jet Propulsion Laboratory in Kalifornien, erlangt. Erste Spektren, die von Proben im Gusev-Krater (Landestelle von „Spirit“) aufgenommen wurden und in dieser Arbeit vorgestellt werden, weisen auf das Vorkommen von forsteritischem Olivin, Pyroxen, Magnetit hin; daneben zeigt sich ein von Eisen(III) herrührendes Quadrupoldublett, das (noch) nicht eindeutig zugeordnet werden konnte. Aus den gewonnenen Daten wurde geschlossen, dass physikalische Verwitterung der vorherrschende Veränderungsprozess in den Ebenen des Gusev-Kraters ist. Um die Fähigkeiten von MIMOS II in der Charakteriserung extraterrestrischen Materials vor dem Start zum Mars zu demonstrieren, wurde eine Auswahl von chondritischen, Eisenund Marsmeteoriten gemessen. Ein Datenanalysepaket, basierend auf künstlichen neuronalen Netzwerken, genetischen Algorithmen und "fuzzy" Logik, wurde erstellt, erfolgreich getestet und während der Echtzeit-Operation der MER benutzt. Eine Datenbasis von Mössbauer-Parametern und Referenzen von veröffentlichten Studien über den Temperaturbereich des Mars wurde zusammengestellt. Die Werkzeuge zur Datenanalyse eröffnen neue Einsatzmöglichkeiten des miniaturisierten Mössbauer-Spektrometers in vielen Bereichen ausserhalb des Physikllabors. Einige davon werden in dieser Arbeit vorgestellt, wie z.B.die Pigmentcharakterisierung, die Echtheit archäologischer Artefakte oder in-situ Luftverschmutzungsmessungen. Datum: 20.07.2004 1. Betreuer: Professor Dr. P. Gütlich Paulo A. de Souza Jr. GAFEP/GETEP Departamento de Pelotização - DIPE Companhia Vale do Rio Doce - CVRD Tel.: (27) 3333-4609 - Carrier (835)

Applications of RFID in the pharmaceutical supply chain

L’obiettivo di questa tesi è principalmente quello di mostrare le possibili applicazioni della tecnologia RFID (Radio Frequency Identification) all’interno della supply chain farmaceutica, cercando di comprendere il campo di applicazione di questa tecnologia in un’industria così altamente regolata e complessa come quella farmaceutica. La tesi è organizzata in tre sezioni; nel primo capitolo si trattano i principi alla base della tecnologia RFID e l’attuale stato dell’arte nella standardizzazione della banda di frequenza utilizzata e nell’hardware. In questa sezione sono poi mostrate le principali applicazioni e nella parte finale i problemi affrontati da un’azienda nell’applicare l’RFID al proprio business. Il secondo capitolo descrive le parti coinvolte nell’industria farmaceutica, dal produttore al consumatore finale, poi esamina le caratteristiche essenziali della supply chain farmaceutica e gli aspetti chiave e le criticità da affrontare in questo campo per essere efficiente e per consegnare il prodotto al cliente in maniera sicura e consistente. Infine nell’ultima sezione i due argomenti centrali sono fusi assieme, cercando di esaminare come la tecnologia RFID sia in grado di risolvere i problemi affrontati da tale industria. Il lavoro non vuole mostrare la tecnologia RFID come una panacea di tutte le problematiche presentate in questa industria, ma vuole cercare di colmare il gap presente in letteratura riguardo le possibili applicazioni di questa tecnologia nell’industria specificata.

Chemical Production and Microelectronic Applications of Graphene and Nano-Graphene Derivatives

Graphene and graphenic derivatives have rapidly emerged as an extremely promising system for electronic, optical, thermal, and electromechanical applications. Several approaches have been developed to produce these materials (i.e. scotch tape, CVD, chemical and solvent exfoliation). In this work we report a chemical approach to produce graphene by reducing graphene oxide (GO) via thermal or electrical methods. A morphological and electrical characterization of these systems has been performed using different techniques such as SPM, SEM, TEM, Raman and XPS. Moreover, we studied the interaction between graphene derivates and organic molecules focusing on the following aspects: - improvement of optical contrast of graphene on different substrates for rapid monolayer identification1 - supramolecular interaction with organic molecules (i.e. thiophene, pyrene etc.)4 - covalent functionalization with optically active molecules2 - preparation and characterization of organic/graphene Field Effect Transistors3-5 Graphene chemistry can potentially allow seamless integration of graphene technology in organic electronics devices to improve device performance and develop new applications for graphene-based materials. [1] E. Treossi, M. Melucci, A. Liscio, M. Gazzano, P. Samorì, and V. Palermo, J. Am. Chem. Soc., 2009, 131, 15576. [2] M. Melucci, E. Treossi, L. Ortolani, G. Giambastiani, V. Morandi, P. Klar, C. Casiraghi, P. Samorì, and V. Palermo, J. Mater. Chem., 2010, 20, 9052. [3] J.M. Mativetsky, E. Treossi, E. Orgiu, M. Melucci, G.P. Veronese, P. Samorì, and V. Palermo, J. Am. Chem. Soc., 2010, 132, 14130. [4] A. Liscio, G.P. Veronese, E. Treossi, F. Suriano, F. Rossella, V. Bellani, R. Rizzoli, P. Samorì and V. Palermo, J. Mater. Chem., 2011, 21, 2924. [5] J.M. Mativetsky, A. Liscio, E. Treossi, E. Orgiu, A. Zanelli, P. Samorì , V. Palermo, J. Am. Chem. Soc., 2011, 133, 14320

Nanoscale effects and applications of self-organized nanostructured thin films

A nanostructured thin film is a thin material layer, usually supported by a (solid) substrate, which possesses subdomains with characteristic nanoscale dimensions (10 ~ 100 nm) that are differentiated by their material properties. Such films have captured vast research interest because the dimensions and the morphology of the nanostructure introduce new possibilities to manipulating chemical and physical properties not found in bulk materials. Block copolymer (BCP) self-assembly, and anodization to form nanoporous anodic aluminium oxide (AAO), are two different methods for generating nanostructures by self-organization. Using poly(styrene-block-methyl methacrylate) (PS-b-PMMA) nanopatterned thin films, it is demonstrated that these polymer nanopatterns can be used to study the influence of nanoscale features on protein-surface interactions. Moreover, a method for the directed assembly of adsorbed protein nanoarrays, based on the nanoscale juxtaposition of the BCP surface domains, is also demonstrated. Studies on protein-nanopattern interactions may inform the design of biomaterials, biosensors, and relevant cell-surface experiments that make use of nanoscale structures. In addition, PS-b-PMMA and AAO thin films are also demonstrated for use as optical waveguides at visible wavelengths. Due to the sub-wavelength nature of the nanostructures, scattering losses are minimized, and the optical response is amenable to analysis with effective medium theory (EMT). Optical waveguide measurements and EMT analysis of the films’ optical anisotropy enabled the in situ characterization of the PS-b-PMMA nanostructure, and a variety of surface processes within the nanoporous AAO involving (bio)macromolecules at high sensitivity.

Modeling and simulations of some anisotropic soft-matter systems: from biaxial to chiral materials

We have modeled various soft-matter systems with molecular dynamics (MD) simulations. The first topic concerns liquid crystal (LC) biaxial nematic (Nb) phases, that can be possibly used in fast displays. We have investigated the phase organization of biaxial Gay-Berne (GB) mesogens, considering the effects of the orientation, strength and position of a molecular dipole. We have observed that for systems with a central dipole, nematic biaxial phases disappear when increasing dipole strength, while for systems characterized by an offset dipole, the Nb phase is stabilized at very low temperatures. In a second project, in view of their increasing importance as nanomaterials in LC phases, we are developing a DNA coarse-grained (CG) model, in which sugar and phosphate groups are represented with Lennard-Jones spheres, while bases with GB ellipsoids. We have obtained shape, position and orientation parameters for each bead, to best reproduce the atomistic structure of a B-DNA helix. Starting from atomistic simulations results, we have completed a first parametrization of the force field terms, accounting for bonded (bonds, angles and dihedrals) and non-bonded interactions (H-bond and stacking). We are currently validating the model, by investigating stability and melting temperature of various sequences. Finally, in a third project, we aim to explain the mechanism of enantiomeric discrimination due to the presence of a chiral helix of poly(gamma-benzyl L-glutamate) (PBLG), in solution of dimethylformamide (DMF), interacting with chiral or pro-chiral molecules (in our case heptyl butyrate, HEP), after tuning properly an atomistic force field (AMBER). We have observed that DMF and HEP molecules solvate uniformly the PBLG helix, but the pro-chiral solute is on average found closer to the helix with respect to the DMF. The solvent presents a faster isotropic diffusion, twice as HEP, also indicating a stronger interaction of the solute with the helix.

Networking: the "making of" social networks. A closer look at the process and antecedents of some resourcing-oriented behaviors in organizations.

Social networks are one of the “hot” themes in people’s life and contemporary social research. Considering our “embeddedness” in a thick web of social relations is a study perspective that could unveil a number of explanations of how people may manage their personal and social resources. Looking at people’s behaviors of building and managing their social networks, seems to be an effective way to find some possible rationalization about how to help people getting the best from their resources . The main aim of this dissertation is to give a closer look at the role of networking behaviors. Antecedents, motivations, different steps and measures about networking behaviors and outcomes are analyzed and discussed. Results seem to confirm, in a different setting and time perspective, that networking behaviors include different types and goals that change over time. Effects of networking behaviors seem to find empirical confirmation through social network analysis methods. Both personality and situational self-efficacy seem to predict networking behaviors. Different types of motivational drivers seem to be related to diverse networking behaviors.

The Dynamics of Passive Torsional Fatigue Test Rigs: Innovative Applications of Universal Joints

The dynamics of a passive back-to-back test rig have been characterised, leading to a multi-coordinate approach for the analysis of arbitrary test configurations. Universal joints have been introduced into a typical pre-loaded back-to-back system in order to produce an oscillating torsional moment in a test specimen. Two different arrangements have been investigated using a frequency-based sub-structuring approach: the receptance method. A numerical model has been developed in accordance with this theory, allowing interconnection of systems with two-coordinates and closed multi-loop schemes. The model calculates the receptance functions and modal and deflected shapes of a general system. Closed form expressions of the following individual elements have been developed: a servomotor, damped continuous shaft and a universal joint. Numerical results for specific cases have been compared with published data in literature and experimental measurements undertaken in the present work. Due to the complexity of the universal joint and its oscillating dynamic effects, a more detailed analysis of this component has been developed. Two models have been presented. The first represents the joint as two inertias connected by a massless cross-piece. The second, derived by the dynamic analysis of a spherical four-link mechanism, considers the contribution of the floating element and its gyroscopic effects. An investigation into non-linear behaviour has led to a time domain model that utilises the Runge-Kutta fourth order method for resolution of the dynamic equations. It has been demonstrated that the torsional receptances of a universal joint, derived using the simple model, result in representation of the joint as an equivalent variable inertia. In order to verify the model, a test rig has been built and experimental validation undertaken. The variable inertia of a universal joint has lead to a novel application of the component as a passive device for the balancing of inertia variations in slider-crank mechanisms.

New biosensor applications of surface plasmon and hydrogel optical waveguide spectroscopy

Rapid and sensitive detection of chemical and biological analytes becomes increasingly important in areas such as medical diagnostics, food control and environmental monitoring. Optical biosensors based on surface plasmon resonance (SPR) and optical waveguide spectroscopy have been extensively pushed forward in these fields. In this study, we combine SPR, surface plasmon-enhanced fluorescence spectroscopy (SPFS) and optical waveguide spectroscopy with hydrogel thin film for highly sensitive detection of molecular analytes.rnrnA novel biosensor based on SPFS which was advanced through the excitation of long range surface plasmons (LRSPs) is reported in this study. LRSPs are special surface plasmon waves propagating along thin metal films with orders of magnitude higher electromagnetic field intensity and lower damping than conventional SPs. Therefore, their excitation on the sensor surface provides further increased fluorescence signal. An inhibition immunoassay based on LRSP-enhanced fluorescence spectroscopy (LRSP-FS) was developed for the detection of aflatoxin M1 (AFM1) in milk. The biosensor allowed for the detection of AFM1 in milk at concentrations as low as 0.6 pg mL-1, which is about two orders of magnitude lower than the maximum AFM1 residue level in milk stipulated by the European Commission legislation.rnrnIn addition, LRSPs probe the medium adjacent to the metallic surface with more extended evanescent field than regular SPs. Therefore, three-dimensional binding matrices with up to micrometer thickness have been proposed for the immobilization of biomolecular recognition elements with large surface density that allows to exploit the whole evanescent field of LRSP. A photocrosslinkable carboxymethyl dextran (PCDM) hydrogel thin film is used as a binding matrix, and it is applied for the detection of free prostate specific antigen (f-PSA) based on the LRSP-FS and sandwich immunoassay. We show that this approach allows for the detection of f-PSA at low femto-molar range, which is approximately four orders of magnitude lower than that for direct detection of f-PSA based on the monitoring of binding-induced refractive index changes.rnrnHowever, a three dimensional hydrogel binding matrix with micrometer thickness can also serve as an optical waveguide. Based on the measurement of binding-induced refractive index changes, a hydrogel optical waveguide spectroscopy (HOWS) is reported for a label-free biosensor. This biosensor is implemented by using a SPR optical setup in which a carboxylated poly(N-isoproprylacrylamide) (PNIPAAm) hydrogel film is attached on a metallic surface and modified by protein catcher molecules. Compared to regular SPR biosensor with thiol self-assembled monolayer (SAM), HOWS provides an order of magnitude improved resolution in the refractive index measurements and enlarged binding capacity owing to its low damping and large swelling ratio, respectively. A model immunoassay experiment revealed that HOWS allowed detection of IgG molecules with a 10 pM limit of detection (LOD) that was five-fold lower than that achieved for SPR with thiol SAM. For the high capacity hydrogel matrix, the affinity binding was mass transport limited.rnrnThe mass transport of target molecules to the sensor surface can play as critical a role as the chemical reaction itself. In order to overcome the diffusion-limited mass transfer, magnetic iron oxide nanoparticles were employed. The magnetic nanoparticles (MNPs) can serve both as labels providing enhancement of the refractive index changes, and “vehicles” for rapidly delivering the analytes from sample solution to an SPR sensor surface with a gradient magnetic field. A model sandwich assay for the detection of β human chorionic gonadotropin (βhCG) has been utilized on a gold sensor surface with metallic diffraction grating structure supporting the excitation of SPs. Various detection formats including a) direct detection, b) sandwich assay, c) MNPs immunoassay without and d) with applied magnetic field were compared. The results show that the highly-sensitive MNPs immunoassay improves the LOD on the detection of βhCG by a factor of 5 orders of magnitude with respect to the direct detection.rn

Development and applications of hollow fiber flow field-flow fractionation in the bioanalytical field. Studies of aggregation phenomena in complex protein samples

Recent advances in the fast growing area of therapeutic/diagnostic proteins and antibodies - novel and highly specific drugs - as well as the progress in the field of functional proteomics regarding the correlation between the aggregation of damaged proteins and (immuno) senescence or aging-related pathologies, underline the need for adequate analytical methods for the detection, separation, characterization and quantification of protein aggregates, regardless of the their origin or formation mechanism. Hollow fiber flow field-flow fractionation (HF5), the miniaturized version of FlowFFF and integral part of the Eclipse DUALTEC FFF separation system, was the focus of this research; this flow-based separation technique proved to be uniquely suited for the hydrodynamic size-based separation of proteins and protein aggregates in a very broad size and molecular weight (MW) range, often present at trace levels. HF5 has shown to be (a) highly selective in terms of protein diffusion coefficients, (b) versatile in terms of bio-compatible carrier solution choice, (c) able to preserve the biophysical properties/molecular conformation of the proteins/protein aggregates and (d) able to discriminate between different types of protein aggregates. Thanks to the miniaturization advantages and the online coupling with highly sensitive detection techniques (UV/Vis, intrinsic fluorescence and multi-angle light scattering), HF5 had very low detection/quantification limits for protein aggregates. Compared to size-exclusion chromatography (SEC), HF5 demonstrated superior selectivity and potential as orthogonal analytical method in the extended characterization assays, often required by therapeutic protein formulations. In addition, the developed HF5 methods have proven to be rapid, highly selective, sensitive and repeatable. HF5 was ideally suitable as first dimension of separation of aging-related protein aggregates from whole cell lysates (proteome pre-fractionation method) and, by HF5-(UV)-MALS online coupling, important biophysical information on the fractionated proteins and protein aggregates was gathered: size (rms radius and hydrodynamic radius), absolute MW and conformation.