Optimal dynamic inversion-based semi-active control of benchmark bridge using MR dampers

A new two-stage state feedback control design approach has been developed to monitor the voltage supplied to magnetorheological (MR) dampers for semi-active vibration control of the benchmark highway bridge. The first stage contains a primary controller, which provides the force required to obtain a desired closed-loop response of the system. In the second stage, an optimal dynamic inversion (ODI) approach has been developed to obtain the amount of voltage to be supplied to each of the MR dampers such that it provides the required force prescribed by the primary controller. ODI is formulated by optimization with dynamic inversion, such that an optimal voltage is supplied to each damper in a set. The proposed control design has been simulated for both phase-I and phase-II study of the recently developed benchmark highway bridge problem. The efficiency of the proposed controller is analyzed in terms of the performance indices defined in the benchmark problem definition. Simulation results demonstrate that the proposed approach generally reduces peak response quantities over those obtained from the sample semi-active controller, although some response quantities have been seen to be increasing. Overall, the proposed control approach is quite competitive as compared with the sample semi-active control approach.

Deflection analysis of hybrid laminated composite plates

In this paper an attempt is made to obtain deflections of hybrid, laminated, rectangular and skew composite plates. Analysis is performed by employing the Galerkin technique. Numerical results have been obtained for two types of layups employing Kevlar/epoxy and Boron/epoxy laminae. It is observed that for a given aspect ratio the rigidity of the skew plate increases with an increase in the skew angle. Further, for a specified deflection, the hybrid laminates turn out to be lighter.

Small nerve fiber quantification in the diagnosis of diabetic sensorimotor polyneuropathy: Comparing corneal confocal microscopy with intraepidermal nerve fiber density

OBJECTIVE Quantitative assessment of small fiber damage is key to the early diagnosis and assessment of progression or regression of diabetic sensorimotor polyneuropathy (DSPN). Intraepidermal nerve fiber density (IENFD) is the current gold standard, but corneal confocal microscopy (CCM), an in vivo ophthalmic imaging modality, has the potential to be a noninvasive and objective image biomarker for identifying small fiber damage. The purpose of this study was to determine the diagnostic performance of CCM and IENFD by using the current guidelines as the reference standard. RESEARCH DESIGN AND METHODS Eighty-nine subjects (26 control subjects and 63 patients with type 1 diabetes), with and without DSPN, underwent a detailed assessment of neuropathy, including CCM and skin biopsy. RESULTS Manual and automated corneal nerve fiber density (CNFD) (P < 0.0001), branch density (CNBD) (P < 0.0001) and length (CNFL) (P < 0.0001), and IENFD (P < 0.001) were significantly reduced in patients with diabetes with DSPN compared with control subjects. The area under the receiver operating characteristic curve for identifying DSPN was 0.82 for manual CNFD, 0.80 for automated CNFD, and 0.66 for IENFD, which did not differ significantly (P = 0.14). CONCLUSIONS This study shows comparable diagnostic efficiency between CCM and IENFD, providing further support for the clinical utility of CCM as a surrogate end point for DSPN.

Finite element analysis of bimodulus composite stiffened thin shells of revolution

This paper is a sequel to the work published by the first and third authors[l] on stiffened laminated shells of revolution made of unimodular materials (materials having identical properties in tension and compression). A finite element analysis of laminated bimodulus composite thin shells of revolution, reinforced by laminated bimodulus composite stiffeners is reported herein. A 48 dot doubly curved quadrilateral laminated anisotropic shell of revolution finite element and it's two compatible 16 dof stiffener finite elements namely: (i) a laminated anisotropic parallel circle stiffener element (PCSE) and (ii) a laminated anisotropic meridional stiffener element (MSE) have been used iteratively. The constitutive relationship of each layer is assumed to depend on whether the fiberdirection strain is tensile or compressive. The true state of strain or stress is realized when the locations of the neutral surfaces in the shell and the stiffeners remain unaltered (to a specified accuracy) between two successive iterations. The solutions for static loading of a stiffened plate, a stiffened cylindrical shell. and a stiffened spherical shell, all made of bimodulus composite materials, have been presented.

Impact of low temperature storage on active and storage forms of folate in choy sum (Brassica rapa subsp parachinensis)

Choy sum (Brassica rapa subsp. parachinensis) is a dark green leafy vegetable that contains high folate (vitamin B9) levels comparable to spinach. Folate is essential for the maintenance of human health and is obtained solely through dietary means. Analysis of the edible portion of choy sum by both microbiological assay and LC-MS/MS indicated that total folate activity remained significantly unchanged over 3 weeks storage at 4 degrees C. Inedible fractions consisted primarily of outer leaves, which showed signs of rotting after 14d, and a combination of rotting and yellowing after 21 d, contributing to 20% and 40% of product removal, respectively. Following deconjugation of the folate present in choy sum to monoglutamate and diglutamate derivatives, the principal forms (vitamers) of folate detected in choy sum were 5-methyltetrahydrofolate and 5-formyl tetrahydrofolate, followed by tetrahydrofolate (THF), 5,10-methenyl-THF, and 10-formyl folic acid. During storage, a significant decline in 5-formyl-THF was observed, with a slight but not significant increase in the combined 5-methyl-THF derivatives. The decline in 5-formyl-THF in relation to the other folate vitamers present may indicate that 5-formyl-THF is being utilised as a folate storage reserve, being interconverted to more metabolically active forms of folate, such as 5-methyl-THF. Although folate vitamer profile changed over the storage period, total folate activity did not significantly change. From a human nutritional perspective this is important, as while particular folate vitamers (e.g. 5-methyl-THF) are necessary for maintaining vital aspects of plant metabolism, it is less important to the human diet, as humans can absorb and interconvert multiple forms of folate. The current trial indicates that it is possible to store choy sum for up to 3 weeks at 4 degrees C without significantly affecting total folate concentration of the edible portion. Crown Copyright (C) 2012 Published by Elsevier B.V. All rights reserved.

Very-high-Q inductor simulation for active tuned filters

Abstract is not available.

A refined analysis of composite laminates

The purpose of this paper is to develop a sufficiently accurate analysis, which is much simpler than exact three-dimensional analysis, for statics and dynamics of composite laminates. The governing differential equations and boundary conditions are derived by following a variational approach. The displacements are assumed piecewise linear across the thickness and the effects of transverse shear deformations and rotary inertia are included. A procedure for obtaining the general solution of the above governing differential equations in the form of hyperbolic-trigonometric series is given. The accuracy of the present theory is assessed by obtaining results for free vibrations and flexure of simply supported rectangular laminates and comparing them with results from exact three-dimensional analysis.

Circulating concentrations of leptin, ovarian follicle number, and oocyte lipid content and active mitochondria, in Zebu crossbred cows maintained on standard or improved nutrition

Zebu (Bos indicus) crossbred beef cows (Droughtmaster) were maintained long-term (16 months) on standard nutrition (SN) or improved nutrition (IN). Cows on IN had better body condition and greater (P<0.05) circulating concentrations of leptin than cows on SN (0.7±0.1n/ml and 1.7±0.1n/ml, respectively). There were no outstanding differences between SN and IN cows in basal number of ovarian follicles (≤4mm, 5-8mm, and≥9mm) and there were also no differences in number of oocytes recovered by oocyte pick-up. Cows on IN had a greater (P<0.05) number of total follicles after stimulation with FSH than cows on SN. Oocytes from cows on IN had greater (P<0.05) lipid content than cows on SN (-0.23±0.16 and 0.20±0.18 arbitrary units, respectively) and oocytes of the former cows also tended to have more active mitochondria, although this was not significant. Cows on IN showed a positive relationship (R2=0.31, P<0.05) between plasma leptin and oocyte lipid content. Lipids are utilized by oocytes during high energy consumptive processes including fertilization and early cleavage. The greater lipid content of oocytes from IN cows could therefore confer a reproductive advantage. The present study has shown relationships between nutrition, body condition, circulating leptin, and oocyte lipid content, but a clear cause-and-effect requires further investigation in the cow. © 2013 Elsevier B.V.

Structural Veneer Based Composite Products from Hardwood Thinning - Part II: Testing of Hollow Utility Poles

Australian utility pole network is aging and reaching its end of life, with 70% of the 5 million poles currently in-service nationally installed within the 20 years following the end of World War II. The estimated investment required for the replacement or remedial maintenance of the aging 3.5 millions poles is as high as 1.75 billion dollars. Additionally, an estimated 21,700 high-durability new poles are required each year, representing further investment of 13.5 million dollars per year. Yet, agreements which progressively phase out logging of native forests around Australia have been signed, giving the industry about 25 years to make the transition from Crown native forests to plantations and private forests. As utility poles were traditionally cut from native forest hardwood species, finding solutions to source new poles currently presents a challenge. This paper presents tests on Veneer Based Composite hardwood hollow utility poles manufactured from Gympie messmate (Eucalyptus cloeziana) plantation thinning. Small diameter poles of nominal 115 mm internal diameter and 15 mm wall-thickness were manufactured in two half-poles butt jointed together, using 9 veneers per halfpole. The poles were tested in bending and shear, and experimental test results are presented. The mechanical performance of the hollow poles is discussed and compared to hardwood poles cut from mature trees and of similar size. Future research and different options for improving the current concept are proposed in order to provide a more reliable and cost effective technical solution to the current shortage of utility poles. © RILEM 2014.

Veneer based composite hollow utility poles manufactured from hardwood plantation thinned trees

Australia’s utility pole network is aging and approaching its end of life. It is estimated that 70% of the 5 million poles currently in-service nationally were installed within the 20 years following the end of World War II and require replacement or remedial maintenance. Additionally, an estimated 21,700 high-durability new poles are required each year to support the expansion of the energy network. Utility poles were traditionally cut from native forest hardwood species. However, due to agreements which progressively phase out logging of native forests around Australia, finding new sources for utility poles presents a challenge. This paper presents the development of veneer based composite hardwood hollow utility poles manufactured from mid-rotation Gympie messmate (Eucalyptus cloeziana) plantation thinned trees (also referred to as “thinning”), as an alternative to solid hardwood poles. The incentives behind the project and benefits of the proposed products are introduced in the paper. Small diameter poles, of nominal 115 mm internal diameter and 15 mm wall-thickness, were manufactured in two half-poles butt jointed together, using 9 hardwood veneers per half-pole. The poles were tested in bending and shear, and experimental test results are presented. The mechanical performance of the hollow poles is discussed and compared to hardwood poles sourced from mature trees and of similar size. Additionally, the required dimensions of the proposed hollow pole to replace actual solid poles are estimated. Results show that the proposed product represents a viable technical solution to the current shortage of utility poles. Future research and different options for improving the current concept are proposed in order to provide a more reliable and cost effective product for structural and architectural applications in general.

Structural Veneer Based Composite Products from Hardwood Thinning - Part I: Background and Manufacturing

In Australia, plantation forests have increased in area by around 50% in the last 10 years. While this expansion has seen a modest 8% increase for softwoods, hardwood plantations have dramatically increased by over 150%. Hardwood plantations grown for high quality sawn timber are slow to mature, with a crop rotation time potentially reaching 35 years. With this long lead-time, each year the risk from fire, pests and adverse weather events dramatically increases, while not translating into substantially higher financial returns to the grower. To justify continued expansion of Australia's current hardwood plantation estate, it is becoming necessary to develop higher value end-uses for both pulpwood and smaller 'sawlog' resources. The use of the low commercial value stems currently culled during thinning appears to be a necessary option to improve the industry profitability and win new markets. This paper provides background information on Australian forests and plantations and gives an overview of potential uses of Australian hardwood plantation thinning logs, as their mechanical properties. More specifically, this paper reports on the development of structural Veneer Based Composite (VBC) products from hardwood plantation thinning logs, taking advantage of a recent technology developed to optimise the processing of this resource. The process used to manufacture a range of hollow-form veneer laminated structural products is presented and the mechanical characteristics of these products are investigated in the companion paper. The market applications and future opportunities for the proposed products are also discussed, as potential benefits to the timber industry. © RILEM 2014.

Active vibration suppression of non-linear beams using optimal dynamic inversion

Euler–Bernoulli beams are distributed parameter systems that are governed by a non-linear partial differential equation (PDE) of motion. This paper presents a vibration control approach for such beams that directly utilizes the non-linear PDE of motion, and hence, it is free from approximation errors (such as model reduction, linearization etc.). Two state feedback controllers are presented based on a newly developed optimal dynamic inversion technique which leads to closed-form solutions for the control variable. In one formulation a continuous controller structure is assumed in the spatial domain, whereas in the other approach it is assumed that the control force is applied through a finite number of discrete actuators located at predefined discrete locations in the spatial domain. An implicit finite difference technique with unconditional stability has been used to solve the PDE with control actions. Numerical simulation studies show that the beam vibration can effectively be decreased using either of the two formulations.

Can Nano Silicon Be Made Optically Active?

There has been a lot of effort to make Silicon optically active. In this work we examine two methods of generating nanocrystals of Silicon from bulk fragments. This approach of ours allows us to play with the shape of the nanocrystals and therefore the degeneracy of the conduction band minimum. We go on to examine whether similar sized particles with different shapes have the same physical properties, and finally whether Silicon may be rendered optically active by this route. While we do find that similar sized particles with different shapes may have different band gaps, this route of modifying the degeneracy of the conduction band minimum makes nano Si slightly optically active.

High value timber composite panels from hardwood plantation thinnings.

Identifying processing strategies and products that suit young plantation hardwoods has proved challenging with low product recoveries and/or unmarketable products being the outcome of many trials. The production of rotary veneer has been demonstrated as an effective method for converting plantation hardwood trees. Across nine processing studies that included six different plantation species (Dunn’s white gum, spotted gum, Gympie messmate, spotted gum hybrid, red mahogany and western white gum), simple spindleless lathe technology was used to process 914 veneer billets totally 37.4 m3.