Sub-tropical high-density, low rise residential buildings: case study 3

The case study 3 team viewed the mitigation of noise and air pollution generated in the transport corridor that borders the study site to be a paramount driver of the urban design solution. These key urban planning strategies were adopted: * Spatial separation from transport corridor pollution source. A linear green zone and environmental buffer was proposed adjacent to the transport corridor to mitigate the environmental noise and air quality impacts of the corridor, and to offer residents opportunities for recreation * Open space forming the key structural principle for neighbourhood design. A significant open space system underpins the planning and manages surface water flows. * Urban blocks running on east-west axis. The open space rationale emphasises an east-west pattern for local streets. Street alignment allows for predominantly north-south facing terrace type buildings which both face the street and overlook the green courtyard formed by the perimeter buildings. The results of the ESD assessment of the typologies conclude that the design will achieve good outcomes through: * Lower than average construction costs compared with other similar projects * Thermal comfort; A good balance between daylight access and solar gains is achieved * The energy rating achieved for the units is 8.5 stars.

Safeguarding rural Australia : addressing masculinity and violence in rural settings : suicide and other violent self-harm in an Australian rural context : analysis of secondary data

This report is an update of an earlier one produced in September 2009 (see Carrington et al. 2009) which remains as an ePrint through the project’s home page. The report focuses on our examination of extant data which have been sourced with respect to self-harm and suicide among males living in regional and remote Australia and which were available in public data bases at production time. Moreover, specific areas of concern regarding elevated rates of suicide for rural males and data anomalies which emerged during our examination of these data are discussed.

Teaching and Learning in Maritime Security: A Literature Review

With the rise in attacks and attempted attacks on marine‐based critical infrastructure, maritime security is an issue of increasing importance worldwide. However, there are three significant shortfalls in the efforts to overcome potential threats to maritime security: the need for greater understanding of whether current standards of best practice are truly successful in combating and reducing the risks of terrorism and other security issues, the absence of a collective maritime security best practice framework and the need for improved access to maritime security specific graduate and postgraduate (long) courses. This paper presents an overview of existing international, regional national standards of best practice and shows that literature concerning the measurement and/ or success of standards is virtually non‐existent. In addition, despite the importance of maritime workers to ensuring the safety of marine based critical infrastructure, a similar review of available Australian education courses shows a considerable lack of availability of maritime security‐specific courses other than short courses that cover only basic security matters. We argue that the absence of an Australian best practice framework informed by evaluation of current policy responses – particularly in the post 9/11 environment – leaves Australia vulnerable to maritime security threats. As this paper shows, the reality is that despite the security measures put in place post 9/11, there is still considerable work to be done to ensure Australia is equipped to overcome the threats posed to maritime security.

Influencing the experience of people in urban public places through mobile mediated interactions

This paper introduces our research on influencing the experience of people in urban public places through mobile mediated interactions. Information and communication technology (ICT) devices are sometimes used to create personal space while in public. ICT devices could also be utilised to digitally augment the urban space with non-privacy sensitive data enabling mobile mediated interactions in an anonymous way between collocated strangers. We present what motivates the research on digital augmentations and mobile mediated interactions between unknown urban dwellers, define the research problem that drives this study and why it is significant research in the field of pervasive social networking. The paper illustrates three design interventions enabling social pervasive content sharing and employing pervasive presence, awareness and anonymous social user interaction in urban public places. The paper concludes with an outlook and summarises the research effort.

Thresholds for error probability measures of business process models

The quality of conceptual business process models is highly relevant for the design of corresponding information systems. In particular, a precise measurement of model characteristics can be beneficial from a business perspective, helping to save costs thanks to early error detection. This is just as true from a software engineering point of view. In this latter case, models facilitate stakeholder communication and software system design. Research has investigated several proposals as regards measures for business process models, from a rather correlational perspective. This is helpful for understanding, for example size and complexity as general driving forces of error probability. Yet, design decisions usually have to build on thresholds, which can reliably indicate that a certain counter-action has to be taken. This cannot be achieved only by providing measures; it requires a systematic identification of effective and meaningful thresholds. In this paper, we derive thresholds for a set of structural measures for predicting errors in conceptual process models. To this end, we use a collection of 2,000 business process models from practice as a means of determining thresholds, applying an adaptation of the ROC curves method. Furthermore, an extensive validation of the derived thresholds was conducted by using 429 EPC models from an Australian financial institution. Finally, significant thresholds were adapted to refine existing modeling guidelines in a quantitative way.

Theoretical and numerical investigation of bending properties of Cu nanowires

Based on the AFM-bending experiments, a molecular dynamics (MD) bending simulation model is established which could accurately account for the full spectrum of the mechanical properties of NWs in a double clamped beam configuration, ranging from elasticity to plasticity and failure. It is found that, loading rate exerts significant influence to the mechanical behaviours of nanowires (NWs). Specifically, a loading rate lower than 10 m/s is found reasonable for a homogonous bending deformation. Both loading rate and potential between the tip and the NW are found to play an important role in the adhesive phenomenon. The force versus displacement (F-d) curve from MD simulation is highly consistent in shapes with that from experiments. Symmetrical F-d curves during loading and unloading processes are observed, which reveal the linear-elastic and non-elastic bending deformation of NWs. The typical bending induced tensile-compressive features are observed. Meanwhile, the simulation results are excellently fitted by the classical Euler-Bernoulli beam theory with axial effect. It is concluded that, axial tensile force becomes crucial in bending deformation when the beam size is down to nanoscale for double clamped NWs. In addition, we find shorter NWs will have an earlier yielding and a larger yielding force. Mechanical properties (Young’s modulus & yield strength) obtained from both bending and tensile deformations are found comparable with each other. Specifically, the modulus is essentially similar under these two loading methods, while the yield strength during bending is observed larger than that during tension.

Cellulosic ethanol from sugarcane bagasse in Australia : exploring industry feasibility through systems analysis, techno-economic assessment and pilot plant development

Overcoming many of the constraints to early stage investment in biofuels production from sugarcane bagasse in Australia requires an understanding of the complex technical, economic and systemic challenges associated with the transition of established sugar industry structures from single product agri-businesses to new diversified multi-product biorefineries. While positive investment decisions in new infrastructure requires technically feasible solutions and the attainment of project economic investment thresholds, many other systemic factors will influence the investment decision. These factors include the interrelationships between feedstock availability and energy use, competing product alternatives, technology acceptance and perceptions of project uncertainty and risk. This thesis explores the feasibility of a new cellulosic ethanol industry in Australia based on the large sugarcane fibre (bagasse) resource available. The research explores industry feasibility from multiple angles including the challenges of integrating ethanol production into an established sugarcane processing system, scoping the economic drivers and key variables relating to bioethanol projects and considering the impact of emerging technologies in improving industry feasibility. The opportunities available from pilot scale technology demonstration are also addressed. Systems analysis techniques are used to explore the interrelationships between the existing sugarcane industry and the developing cellulosic biofuels industry. This analysis has resulted in the development of a conceptual framework for a bagassebased cellulosic ethanol industry in Australia and uses this framework to assess the uncertainty in key project factors and investment risk. The analysis showed that the fundamental issue affecting investment in a cellulosic ethanol industry from sugarcane in Australia is the uncertainty in the future price of ethanol and government support that reduces the risks associated with early stage investment is likely to be necessary to promote commercialisation of this novel technology. Comprehensive techno-economic models have been developed and used to assess the potential quantum of ethanol production from sugarcane in Australia, to assess the feasibility of a soda-based biorefinery at the Racecourse Sugar Mill in Mackay, Queensland and to assess the feasibility of reducing the cost of production of fermentable sugars from the in-planta expression of cellulases in sugarcane in Australia. These assessments show that ethanol from sugarcane in Australia has the potential to make a significant contribution to reducing Australia’s transportation fuel requirements from fossil fuels and that economically viable projects exist depending upon assumptions relating to product price, ethanol taxation arrangements and greenhouse gas emission reduction incentives. The conceptual design and development of a novel pilot scale cellulosic ethanol research and development facility is also reported in this thesis. The establishment of this facility enables the technical and economic feasibility of new technologies to be assessed in a multi-partner, collaborative environment. As a key outcome of this work, this study has delivered a facility that will enable novel cellulosic ethanol technologies to be assessed in a low investment risk environment, reducing the potential risks associated with early stage investment in commercial projects and hence promoting more rapid technology uptake. While the study has focussed on an exploration of the feasibility of a commercial cellulosic ethanol industry from sugarcane in Australia, many of the same key issues will be of relevance to other sugarcane industries throughout the world seeking diversification of revenue through the implementation of novel cellulosic ethanol technologies.

A descriptive approach for power system stability and security assessment

Power system dynamic analysis and security assessment are becoming more significant today due to increases in size and complexity from restructuring, emerging new uncertainties, integration of renewable energy sources, distributed generation, and micro grids. Precise modelling of all contributed elements/devices, understanding interactions in detail, and observing hidden dynamics using existing analysis tools/theorems are difficult, and even impossible. In this chapter, the power system is considered as a continuum and the propagated electomechanical waves initiated by faults and other random events are studied to provide a new scheme for stability investigation of a large dimensional system. For this purpose, the measured electrical indices (such as rotor angle and bus voltage) following a fault in different points among the network are used, and the behaviour of the propagated waves through the lines, nodes, and buses is analyzed. The impact of weak transmission links on a progressive electromechanical wave using energy function concept is addressed. It is also emphasized that determining severity of a disturbance/contingency accurately, without considering the related electromechanical waves, hidden dynamics, and their properties is not secure enough. Considering these phenomena takes heavy and time consuming calculation, which is not suitable for online stability assessment problems. However, using a continuum model for a power system reduces the burden of complex calculations

Flexible high voltage pulsed power supply for plasma applications

Demands for delivering high instantaneous power in a compressed form (pulse shape) have widely increased during recent decades. The flexible shapes with variable pulse specifications offered by pulsed power have made it a practical and effective supply method for an extensive range of applications. In particular, the release of basic subatomic particles (i.e. electron, proton and neutron) in an atom (ionization process) and the synthesizing of molecules to form ions or other molecules are among those reactions that necessitate large amount of instantaneous power. In addition to the decomposition process, there have recently been requests for pulsed power in other areas such as in the combination of molecules (i.e. fusion, material joining), gessoes radiations (i.e. electron beams, laser, and radar), explosions (i.e. concrete recycling), wastewater, exhausted gas, and material surface treatments. These pulses are widely employed in the silent discharge process in all types of materials (including gas, fluid and solid); in some cases, to form the plasma and consequently accelerate the associated process. Due to this fast growing demand for pulsed power in industrial and environmental applications, the exigency of having more efficient and flexible pulse modulators is now receiving greater consideration. Sensitive applications, such as plasma fusion and laser guns also require more precisely produced repetitive pulses with a higher quality. Many research studies are being conducted in different areas that need a flexible pulse modulator to vary pulse features to investigate the influence of these variations on the application. In addition, there is the need to prevent the waste of a considerable amount of energy caused by the arc phenomena that frequently occur after the plasma process. The control over power flow during the supply process is a critical skill that enables the pulse supply to halt the supply process at any stage. Different pulse modulators which utilise different accumulation techniques including Marx Generators (MG), Magnetic Pulse Compressors (MPC), Pulse Forming Networks (PFN) and Multistage Blumlein Lines (MBL) are currently employed to supply a wide range of applications. Gas/Magnetic switching technologies (such as spark gap and hydrogen thyratron) have conventionally been used as switching devices in pulse modulator structures because of their high voltage ratings and considerably low rising times. However, they also suffer from serious drawbacks such as, their low efficiency, reliability and repetition rate, and also their short life span. Being bulky, heavy and expensive are the other disadvantages associated with these devices. Recently developed solid-state switching technology is an appropriate substitution for these switching devices due to the benefits they bring to the pulse supplies. Besides being compact, efficient, reasonable and reliable, and having a long life span, their high frequency switching skill allows repetitive operation of pulsed power supply. The main concerns in using solid-state transistors are the voltage rating and the rising time of available switches that, in some cases, cannot satisfy the application’s requirements. However, there are several power electronics configurations and techniques that make solid-state utilisation feasible for high voltage pulse generation. Therefore, the design and development of novel methods and topologies with higher efficiency and flexibility for pulsed power generators have been considered as the main scope of this research work. This aim is pursued through several innovative proposals that can be classified under the following two principal objectives. • To innovate and develop novel solid-state based topologies for pulsed power generation • To improve available technologies that have the potential to accommodate solid-state technology by revising, reconfiguring and adjusting their structure and control algorithms. The quest to distinguish novel topologies for a proper pulsed power production was begun with a deep and through review of conventional pulse generators and useful power electronics topologies. As a result of this study, it appears that efficiency and flexibility are the most significant demands of plasma applications that have not been met by state-of-the-art methods. Many solid-state based configurations were considered and simulated in order to evaluate their potential to be utilised in the pulsed power area. Parts of this literature review are documented in Chapter 1 of this thesis. Current source topologies demonstrate valuable advantages in supplying the loads with capacitive characteristics such as plasma applications. To investigate the influence of switching transients associated with solid-state devices on rise time of pulses, simulation based studies have been undertaken. A variable current source is considered to pump different current levels to a capacitive load, and it was evident that dissimilar dv/dts are produced at the output. Thereby, transient effects on pulse rising time are denied regarding the evidence acquired from this examination. A detailed report of this study is given in Chapter 6 of this thesis. This study inspired the design of a solid-state based topology that take advantage of both current and voltage sources. A series of switch-resistor-capacitor units at the output splits the produced voltage to lower levels, so it can be shared by the switches. A smart but complicated switching strategy is also designed to discharge the residual energy after each supply cycle. To prevent reverse power flow and to reduce the complexity of the control algorithm in this system, the resistors in common paths of units are substituted with diode rectifiers (switch-diode-capacitor). This modification not only gives the feasibility of stopping the load supply process to the supplier at any stage (and consequently saving energy), but also enables the converter to operate in a two-stroke mode with asymmetrical capacitors. The components’ determination and exchanging energy calculations are accomplished with respect to application specifications and demands. Both topologies were simply modelled and simulation studies have been carried out with the simplified models. Experimental assessments were also executed on implemented hardware and the approaches verified the initial analysis. Reports on details of both converters are thoroughly discussed in Chapters 2 and 3 of the thesis. Conventional MGs have been recently modified to use solid-state transistors (i.e. Insulated gate bipolar transistors) instead of magnetic/gas switching devices. Resistive insulators previously used in their structures are substituted by diode rectifiers to adjust MGs for a proper voltage sharing. However, despite utilizing solid-state technology in MGs configurations, further design and control amendments can still be made to achieve an improved performance with fewer components. Considering a number of charging techniques, resonant phenomenon is adopted in a proposal to charge the capacitors. In addition to charging the capacitors at twice the input voltage, triggering switches at the moment at which the conducted current through switches is zero significantly reduces the switching losses. Another configuration is also introduced in this research for Marx topology based on commutation circuits that use a current source to charge the capacitors. According to this design, diode-capacitor units, each including two Marx stages, are connected in cascade through solid-state devices and aggregate the voltages across the capacitors to produce a high voltage pulse. The polarity of voltage across one capacitor in each unit is reversed in an intermediate mode by connecting the commutation circuit to the capacitor. The insulation of input side from load side is provided in this topology by disconnecting the load from the current source during the supply process. Furthermore, the number of required fast switching devices in both designs is reduced to half of the number used in a conventional MG; they are replaced with slower switches (such as Thyristors) that need simpler driving modules. In addition, the contributing switches in discharging paths are decreased to half; this decrease leads to a reduction in conduction losses. Associated models are simulated, and hardware tests are performed to verify the validity of proposed topologies. Chapters 4, 5 and 7 of the thesis present all relevant analysis and approaches according to these topologies.

Development and validation of an expedited 10g protein counter (EP-10) for dietary protein intake quantification

Precise protein quantification is essential in clinical dietetics, particularly in the management of renal, burn and malnourished patients. The EP-10 was developed to expedite the estimation of dietary protein for nutritional assessment and recommendation. The main objective of this study was to compare the validity and efficacy of the EP-10 with the American Dietetic Association’s “Exchange List for Meal Planning” (ADA-7g) in quantifying dietary protein intake, against computerised nutrient analysis (CNA). Protein intake of 197 food records kept by healthy adult subjects in Singapore was determined thrice using three different methods – (1) EP-10, (2) ADA-7g and (3) CNA using SERVE program (Version 4.0). Assessments using the EP-10 and ADA-7g were performed by two assessors in a blind crossover manner while a third assessor performed the CNA. All assessors were blind to each other’s results. Time taken to assess a subsample (n=165) using the EP-10 and ADA-7g was also recorded. Mean difference in protein intake quantification when compared to the CNA was statistically non-significant for the EP-10 (1.4 ± 16.3 g, P = .239) and statistically significant for the ADA-7g (-2.2 ± 15.6 g, P = .046). Both the EP-10 and ADA-7g had clinically acceptable agreement with the CNA as determined via Bland-Altman plots, although it was found that EP-10 had a tendency to overestimate with protein intakes above 150 g. The EP-10 required significantly less time for protein intake quantification than the ADA-7g (mean time of 65 ± 36 seconds vs. 111 ± 40 seconds, P < .001). The EP-10 and ADA-7g are valid clinical tools for protein intake quantification in an Asian context, with EP-10 being more time efficient. However, a dietician’s discretion is needed when the EP-10 is used on protein intakes above 150g.

A child led participatory approach for technology-based intervention

There is significant interest in Human-computer interaction methods that assist in the design of applications for use by children. Many of these approaches draw upon standard HCI methods,such as personas, scenarios, and probes. However, often these techniques require communication and kinds of thinking skills that are designer centred,which prevents children with Autism Spectrum Disorders or other learning and communication disabilities from being able to participate. This study investigates methods that might be used with children with ASD or other learning and communication disabilities to inspire the design of technology based intervention approaches to support their speech and language development. Similar to Iversen and Brodersen, we argue that children with ASD should not be treated as being in some way “cognitively incomplete”. Rather they are experts in their everyday lives and we cannot design future IT without involving them. However, how do we involve them Instead of beginning with HCI methods, we draw upon easy to use technologies and methods used in the therapy professions for child engagement, particularly utilizing the approaches of Hanen (2011) and Greenspan (1998). These approaches emphasize following the child’s lead and ensuring that the child always has a legitimate turn at a detailed level of interaction. In a pilot project, we have studied a child’s interactions with their parents about activities over which they have control – photos that they have taken at school on an iPad. The iPad was simple enough for this child with ASD to use and they enjoyed taking and reviewing photos. We use this small case study as an example of a child-led approach for a child with ASD. We examine interactions from this study in order to assess the possibilities and limitations of the child-led approach for supporting the design of technology based interventions to support speech and language development.

The identification and quantification of temperature-related mortality

The relationship between weather and mortality has been observed for centuries. Recently, studies on temperature-related mortality have become a popular topic as climate change continues. Most of the previous studies found that exposure to hot or cold temperature affects mortality. This study aims to address three research questions: 1. What is the overall effect of daily mean temperature variation on the elderly mortality in the published literature using a meta-analysis approach? 2. Does the association between temperature and mortality differ with age, sex, or socio-economic status in Brisbane? 3. How is the magnitude of the lag effects of the daily mean temperature on mortality varied by age and cause-of-death groups in Brisbane? In the meta-analysis, there was a 1-2 % increase in all-cause mortality for a 1ºC decrease during cold temperature intervals and a 2-5% increase for a 1ºC increment during hot temperature intervals among the elderly. Lags of up to 9 days in exposure to cold temperature intervals were statistically significantly associated with all-cause mortality, but no significant lag effects were observed for hot temperature intervals. In Brisbane, the harmful effect of high temperature (over 24ºC) on mortality appeared to be greater among the elderly than other age groups. The effect estimate among women was greater than among men. However, No evidence was found that socio-economic status modified the temperature-mortality relationship. The results of this research also show longer lag effects in cold days and shorter lag effects in hot days. For 3-day hot effects associated with 1°C increase above the threshold, the highest percent increases in mortality occurred among people aged 85 years or over (5.4% (95% CI: 1.4%, 9.5%)) compared with all age group (3.2% (95% CI: 0.9%, 5.6%)). The effect estimate among cardiovascular deaths was slightly higher than those among all-cause mortality. For overall 21-day cold effects associated with a 1°C decrease below the threshold, the percent estimates in mortality for people aged 85 years or over, and from cardiovascular diseases were 3.9% (95% CI: 1.9%, 6.0%) and 3.4% (95% CI: 0.9%, 6.0%), respectively compared with all age group (2.0% (95% CI: 0.7%, 3.3%)). Little research of this kind has been conducted in the Southern Hemisphere. This PhD research may contribute to the quantitative assessment of the overall impact, effect modification and lag effects of temperature variation on mortality in Australia and The findings may provide useful information for the development and implementation of public health policies to reduce and prevent temperature-related health problems.

An investigation of commuter exposure to ultrafine particles in Sydney

Commuting in various transport modes represents an activity likely to incur significant exposure to traffic emissions. This study investigated the determinants and characteristics of exposure to ultrafine (< 100 nm) particles (UFPs) in four transport modes in Sydney, with a specific focus on exposure in automobiles, which remain the transport mode of choice for approximately 70% of Sydney commuters. UFP concentrations were measured using a portable condensation particle counter (CPC) inside five automobiles commuting on above ground and tunnel roadways, and in buses, ferries and trains. Determinant factors investigated included wind speed, cabin ventilation (automobiles only) and traffic volume. The results showed that concentrations varied significantly as a consequence of transport mode, vehicle type and ventilation characteristics. The effects of wind speed were minimal relative to those of traffic volume (especially heavy diesel vehicles) and cabin ventilation, with the latter proving to be a strong determinant of UFP ingress into automobiles. The effect of ~70 minutes of commuting on total daily exposure was estimated using a range of UFP concentrations reported for several microenvironments. A hypothetical Sydney resident commuting by automobile and spending 8.5 minutes of their day in the M5 East tunnel could incur anywhere from a lower limit of 3-11% to an upper limit of 37-69% of daily UFP exposure during a return commute, depending on the concentrations they encountered in other microenvironments, the type of vehicle they used and the ventilation setting selected. However, commute-time exposures at either extreme of the values presented are unlikely to occur in practice. The range of exposures estimated for other transport modes were comparable to those of automobiles, and in the case of buses, higher than automobiles.

The rise of co-creative consumers : user experience sharing behaviour in online communities

This thesis examines consumer initiated value co-creation behaviour in the context of convergent mobile online services using a Service-Dominant logic (SD logic) theoretical framework. It focuses on non-reciprocal marketing phenomena such as open innovation and user generated content whereby new viable business models are derived and consumer roles and community become essential to the success of business. Attention to customers. roles and personalised experiences in value co-creation has been recognised in the literature (e.g., Prahalad & Ramaswamy, 2000; Prahalad, 2004; Prahalad & Ramaswamy, 2004). Similarly, in a subsequent iteration of their 2004 version of the foundations of SD logic, Vargo and Lusch (2006) replaced the concept of value co-production with value co-creation and suggested that a value co-creation mindset is essential to underpin the firm-customer value creation relationship. Much of this focus, however, has been limited to firm initiated value co-creation (e.g., B2B or B2C), while consumer initiated value creation, particularly consumer-to-consumer (C2C) has received little attention in the SD logic literature. While it is recognised that not every consumer wishes to make the effort to engage extensively in co-creation processes (MacDonald & Uncles, 2009), some consumers may not be satisfied with a standard product, instead they engage in the effort required for personalisation that potentially leads to greater value for themselves, and which may benefit not only the firm, but other consumers as well. Literature suggests that there are consumers who do, and as a result initiate such behaviour and expend effort to engage in co-creation activity (e.g., Gruen, Osmonbekov and Czaplewski, 2006; 2007 MacDonald & Uncles, 2009). In terms of consumers. engagement in value proposition (co-production) and value actualisation (co-creation), SD logic (Vargo & Lusch, 2004, 2008) provides a new lens that enables marketing scholars to transcend existing marketing theory and facilitates marketing practitioners to initiate service centric and value co-creation oriented marketing practices. Although the active role of the consumer is acknowledged in the SD logic oriented literature, we know little about how and why consumers participate in a value co-creation process (Payne, Storbacka, & Frow, 2008). Literature suggests that researchers should focus on areas such as C2C interaction (Gummesson 2007; Nicholls 2010) and consumer experience sharing and co-creation (Belk 2009; Prahalad & Ramaswamy 2004). In particular, this thesis seeks to better understand consumer initiated value co-creation, which is aligned with the notion that consumers can be resource integrators (Baron & Harris, 2008) and more. The reason for this focus is that consumers today are more empowered in both online and offline contexts (Füller, Mühlbacher, Matzler, & Jawecki, 2009; Sweeney, 2007). Active consumers take initiatives to engage and co-create solutions with other active actors in the market for their betterment of life (Ballantyne & Varey, 2006; Grönroos & Ravald, 2009). In terms of the organisation of the thesis, this thesis first takes a „zoom-out. (Vargo & Lusch, 2011) approach and develops the Experience Co-Creation (ECo) framework that is aligned with balanced centricity (Gummesson, 2008) and Actor-to-Actor worldview (Vargo & Lusch, 2011). This ECo framework is based on an extended „SD logic friendly lexicon. (Lusch & Vargo, 2006): value initiation and value initiator, value-in-experience, betterment centricity and betterment outcomes, and experience co-creation contexts derived from five gaps identified from the SD logic literature review. The framework is also designed to accommodate broader marketing phenomena (i.e., both reciprocal and non-reciprocal marketing phenomena). After zooming out and establishing the ECo framework, the thesis takes a zoom-in approach and places attention back on the value co-creation process. Owing to the scope of the current research, this thesis focuses specifically on non-reciprocal value co-creation phenomena initiated by consumers in online communities. Two emergent concepts: User Experience Sharing (UES) and Co-Creative Consumers are proposed grounded in the ECo framework. Together, these two theorised concepts shed light on the following two propositions: (1) User Experience Sharing derives value-in-experience as consumers make initiative efforts to participate in value co-creation, and (2) Co-Creative Consumers are value initiators who perform UES. Three research questions were identified underpinning the scope of this research: RQ1: What factors influence consumers to exhibit User Experience Sharing behaviour? RQ2: Why do Co-Creative Consumers participate in User Experience Sharing as part of value co-creation behaviour? RQ3: What are the characteristics of Co-Creative Consumers? To answer these research questions, two theoretical models were developed: the User Experience Sharing Behaviour Model (UESBM) grounded in the Theory of Planned Behaviour framework, and the Co-Creative Consumer Motivation Model (CCMM) grounded in the Motivation, Opportunity, Ability framework. The models use SD logic consistent constructs and draw upon multiple streams of literature including consumer education, consumer psychology and consumer behaviour, and organisational psychology and organisational behaviour. These constructs include User Experience Sharing with Other Consumers (UESC), User Experience Sharing with Firms (UESF), Enjoyment in Helping Others (EIHO), Consumer Empowerment (EMP), Consumer Competence (COMP), and Intention to Engage in User Experience Sharing (INT), Attitudes toward User Experience Sharing (ATT) and Subjective Norm (SN) in the UESBM, and User Experience Sharing (UES), Consumer Citizenship (CIT), Relating Needs of Self (RELS) and Relating Needs of Others (RELO), Newness (NEW), Mavenism (MAV), Use Innovativeness (UI), Personal Initiative (PIN) and Communality (COMU) in the CCMM. Many of these constructs are relatively new to marketing and require further empirical evidence for support. Two studies were conducted to underpin the corresponding research questions. Study One was conducted to calibrate and re-specify the proposed models. Study Two was a replica study to confirm the proposed models. In Study One, data were collected from a PC DIY online community. In Study Two, a majority of data were collected from Apple product online communities. The data were examined using structural equation modelling and cluster analysis. Considering the nature of the forums, the Study One data is considered to reflect some characteristics of Prosumers and the Study Two data is considered to reflect some characteristics of Innovators. The results drawn from two independent samples (N = 326 and N = 294) provide empirical support for the overall structure theorised in the research models. The results in both models show that Enjoyment in Helping Others and Consumer Competence in the UESBM, and Consumer Citizenship and Relating Needs in CCMM have significant impacts on UES. The consistent results appeared in both Study One and Study Two. The results also support the conceptualisation of Co-Creative Consumers and indicate Co-Creative Consumers are individuals who are able to relate the needs of themselves and others and feel a responsibility to share their valuable personal experiences. In general, the results shed light on "How and why consumers voluntarily participate in the value co-creation process?. The findings provide evidence to conceptualise User Experience Sharing behaviour as well as the Co-Creative Consumer using the lens of SD logic. This research is a pioneering study that incorporates and empirically tests SD logic consistent constructs to examine a particular area of the logic – that is consumer initiated value co-creation behaviour. This thesis also informs practitioners about how to facilitate and understand factors that engage with either firm or consumer initiated online communities.

Dark numbers: challenges in measuring human trafficking

Over the last decade nations around the world have renewed their efforts to address the problem of human trafficking, following the introduction of the United Nations Protocol to Prevent, Suppress and Punish Trafficking in Persons, Especially Women and Children. In Australia and the United States, legislators sought to quantify and characterise the human trafficking phenomenon, seeking to answer the question — how large is the problem of trafficking? This article explores the attempts of legislators in Australia and the United States to determine how many victims are trafficked into their countries, highlighting the significant uncertainty that still surrounds data on human trafficking. The challenges researchers face in measuring human trafficking are also explored. These challenges include disputes over the definition of a trafficking victim, the limitations of research using sampling to measure the trafficked population, and the mischaracterisation of the trafficking problem as a result of politicisation of the trafficking debate and a focus on trafficking for sexual exploitation versus other forms of labour. This article argues that in the absence of reliable data on trafficking, policy is often informed by misleading or false information.