An improved representation of vehicle incompatibility in frontal NCAP tests using a modified rigid barrier

With the objective of better understanding the significance of New Car Assessment Program (NCAP) tests conducted by the National Highway Traffic Safety Administration (NHTSA), head-on collisions between two identical cars of different sizes and between cars and a pickup truck are studied in the present paper using LS-DYNA models. Available finite element models of a compact car (Dodge Neon), midsize car (Dodge Intrepid), and pickup truck (Chevrolet C1500) are first improved and validated by comparing theanalysis-based vehicle deceleration pulses against corresponding NCAP crash test histories reported by NHTSA. In confirmation of prevalent perception, simulation-bascd results indicate that an NCAP test against a rigid barrier is a good representation of a collision between two similar cars approaching each other at a speed of 56.3 kmph (35 mph) both in terms of peak deceleration and intrusions. However, analyses carried out for collisions between two incompatible vehicles, such as an Intrepid or Neon against a C1500, point to the inability of the NCAP tests in representing the substantially higher intrusions in the front upper regions experienced by the cars, although peak decelerations in cars arc comparable to those observed in NCAP tests. In an attempt to improve the capability of a front NCAP test to better represent real-world crashes between incompatible vehicles, i.e., ones with contrasting ride height and lower body stiffness, two modified rigid barriers are studied. One of these barriers, which is of stepped geometry with a curved front face, leads to significantly improved correlation of intrusions in the upper regions of cars with respect to those yielded in the simulation of collisions between incompatible vehicles, together with the yielding of similar vehicle peak decelerations obtained in NCAP tests.

Performance evaluation of an integrated solar water heater as an option for building energy conservation

Since a majority of residential and industrial building hot water needs are around 50 degrees C, an integrated solar water heater could provide a bulk source that blends collection and storage into one unit. This paper describes the design, construction and performance test results of one such water-heating device. The test unit has an absorber area of 1.3 m(2) and can hold 1701 of water, of which extractable volume per day is 1001. Its performance was evaluated under various typical operating conditions. Every morning at about 7:00 a.m., 1001 of hot water were drawn from the sump and replaced with cold water from the mains. Although, during most of the days, the peak temperatures of water obtained are between 50 and 60 degrees C, the next morning temperatures were lower at 45-50 degrees C. Daytime collection efficiencies of about 60% and overall efficiencies of about 40% were obtained. Tests were conducted with and without stratification. Night radiation losses were reduced by use of a screen insulation.

Random matrices: Universality of ESDs and the circular law

Given an n x n complex matrix A, let mu(A)(x, y) := 1/n vertical bar{1 <= i <= n, Re lambda(i) <= x, Im lambda(i) <= y}vertical bar be the empirical spectral distribution (ESD) of its eigenvalues lambda(i) is an element of C, i = l, ... , n. We consider the limiting distribution (both in probability and in the almost sure convergence sense) of the normalized ESD mu(1/root n An) of a random matrix A(n) = (a(ij))(1 <= i, j <= n), where the random variables a(ij) - E(a(ij)) are i.i.d. copies of a fixed random variable x with unit variance. We prove a universality principle for such ensembles, namely, that the limit distribution in question is independent of the actual choice of x. In particular, in order to compute this distribution, one can assume that x is real or complex Gaussian. As a related result, we show how laws for this ESD follow from laws for the singular value distribution of 1/root n A(n) - zI for complex z. As a corollary, we establish the circular law conjecture (both almost surely and in probability), which asserts that mu(1/root n An) converges to the uniform measure on the unit disc when the a(ij) have zero mean.

The dimensions of the ester unit

The dimensions of the ester unit, which is a component of the depsipeptide unit has been obtained by analysing the data on crystal structures of compounds having the ester unit. The dimensions indicate that this unit is slightly different from the peptide unit both as far as the bond length and bond angles are concerned.

Molecular conformation of alamethicin in dimethylsulfoxide solution A two-dimensional n.m.r. study

The solution conformation of alamethicin, a 20-residue antibiotic peptide, has been investigated using two-dimensional n.m.r. spectroscopy. Complete proton resonance assignments of this peptide have been carried out using COSY, SUPERCOSY, RELAY COSY and NOESY two-dimensional spectroscopies. Observation of a large number of nuclear Overhauser effects between sequential backbone amide protons, between backbone amide protons and CβH protons of preceding residues and extensive intramolecular hydrogen bonding patterns of NH protons has established that this polypeptide is in a largely helical conformation. This result is in conformity with earlier reported solid state X-ray results and a recent n.m.r. study in methanol solution (Esposito et al. (1987) Biochemistry26, 1043-1050) but is at variance with an earlier study which favored an extended conformation for the C-terminal half of alamethicin (Bannerjee et al.

Parametrized tests of post-Newtonian theory using Advanced LIGO and Einstein Telescope

General relativity has very specific predictions for the gravitational waveforms from inspiralling compact binaries obtained using the post-Newtonian (PN) approximation. We investigate the extent to which the measurement of the PN coefficients, possible with the second generation gravitational-wave detectors such as the Advanced Laser Interferometer Gravitational-Wave Observatory (LIGO) and the third generation gravitational-wave detectors such as the Einstein Telescope (ET), could be used to test post-Newtonian theory and to put bounds on a subclass of parametrized-post-Einstein theories which differ from general relativity in a parametrized sense. We demonstrate this possibility by employing the best inspiralling waveform model for nonspinning compact binaries which is 3.5PN accurate in phase and 3PN in amplitude. Within the class of theories considered, Advanced LIGO can test the theory at 1.5PN and thus the leading tail term. Future observations of stellar mass black hole binaries by ET can test the consistency between the various PN coefficients in the gravitational-wave phasing over the mass range of 11-44M(circle dot). The choice of the lower frequency cutoff is important for testing post-Newtonian theory using the ET. The bias in the test arising from the assumption of nonspinning binaries is indicated.

Sequential design of decentralized control systems

Our main result is a new sequential method for the design of decentralized control systems. Controller synthesis is conducted on a loop-by-loop basis, and at each step the designer obtains an explicit characterization of the class C of all compensators for the loop being closed that results in closed-loop system poles being in a specified closed region D of the s-plane, instead of merely stabilizing the closed-loop system. Since one of the primary goals of control system design is to satisfy basic performance requirements that are often directly related to closed-loop pole location (bandwidth, percentage overshoot, rise time, settling time), this approach immediately allows the designer to focus on other concerns such as robustness and sensitivity. By considering only compensators from class C and seeking the optimum member of that set with respect to sensitivity or robustness, the designer has a clearly-defined limited optimization problem to solve without concern for loss of performance. A solution to the decentralized tracking problem is also provided. This design approach has the attractive features of expandability, the use of only 'local models' for controller synthesis, and fault tolerance with respect to certain types of failure.

Easily Diagnosable Sequential Machines

This correspondence throws some light into the area of easily diagnosable machines. Given the behavior of a sequential machine in terms of a state table it explores the possibilities of designing a structure, that facilitates easy diagnosis of faults. The objective is achieved through structural decomposition which has already claimed to produce simpler physical realization.

Early biochemical events during adventitious root initiation in the hypocotyl of Phaseolus vulgaris

Indole butyric acid (IBA) initiates roots in the hypocotyl tissue of Phaseolus vulgaris (French bean). The response is dependent on the concentration of IBA and the duration of exposure to the hormone. IBA enhances the rate of total protein synthesis in ca 30 min after exposure of the hypocotyl segments to the hormone. There is no detectable change in total or poly(A)-containing RNA synthesis in this period although significant increases are seen 2 hr after hormone pre-treatment. The early IBA-mediated increase in protein synthesis (30 min) is not sensitive to Actinomycin D but the antibiotic blocks the increase manifested 2 hr after hormone pre-treatment. Inhibition of early protein synthesis by cycloheximide depresses and delays root initiation. Cytosol prepared from IBA-treated hypocotyl tissue stimulates protein synthesis in vitro to a greater extent than that of the control.

An Experimental and Numerical Study of Calliphora Wing Structure

Experiments are performed to determine the mass and stiffness variations along the wing of the blowfly Calliphora. The results are obtained for a pairs of wings of 10 male flies and fresh wings are used. The wing is divided into nine locations along the span and seven locations along the chord based on venation patterns. The length and mass of the sections is measured and the mass per unit length is calculated. The bending stiffness measurements are taken at three locations, basal (near root), medial and distal (near tip) of the fly wing. Torsional stiffness measurements are also made and the elastic axis of the wing is approximately located. The experimental data is then used for structural modeling of the wing as a stepped cantilever beam with nine spanwise sections of varying mass per unit lengths, flexural rigidity (EI) and torsional rigidity (GJ) values. Inertial values of nine sections are found to approximately vary according to an exponentially decreasing law over the nine sections from root to tip and it is used to calculate an approximate value of Young's modulus of the wing biomaterial. Shear modulus is obtained assuming the wing biomaterial to be isotropic. Natural frequencies, both in bending and torsion, are obtained by solving the homogeneous part of the respective governing differential equations using the finite element method. The results provide a complete analysis of Calliphora wing structure and also provide guidelines for the biomimetic structural design of insect-scale flapping wings.

Diversitet och tillväxtfrämjande egenskaper hos Stenotrophomonas-endofyter isolerade från Calliandra calothyrsus Meisn. rotknölar

The bacterial genus Stenotrophomonas comprises 12 species. They are widely found throughout the environment and particularly S. maltophilia, S. rhizophila and S. pavanii are closely associated with plants. Strains of the most common Stenotrophomonas species, S. maltophilia, promote plant growth and health, degrade natural and man-made pollutants and produce biomolecules of biotechnological and economical value. Many S. maltophilia –strains are also multidrug resistant and can act as opportunistic human pathogens. During an INCO-project (1998-2002) rhizobia were collected from root nodules of the tropical leguminous tree Calliandra calothyrsus Meisn. from several countries in Central America, Africa and New Caledonia. The strains were identified by the N2-group (Helsinki university) and some strains turned out to be members of the genus Stenotrophomonas. Several Stenotrophomonas strains induced white tumor- or nodule-like structures on Calliandra?s roots in plant experiments. The strains could, besides from root nodules, also be isolated from surface sterilized roots and stems. The purpose of my work was to investigate if the Stenotrophomonas strains i) belong to a new Stenotrophomonas species, ii) have the same origin, iii) if there are other differences than colony morphology between phase variations of the same strain, iv) have plant growth-promoting (PGP) activity or other advantageous effects on plants, and v) like rhizobia have ability to induce root nodule formation. The genetic diversity and clustering of the Stenotrophomonas strains were analyzed with AFLP fingerprinting to get indications about their geographical origin. Differences in enzymatic properties and ability to use different carbon and energy sources were tested between the two phases of each strain with commercial API tests for bacterial identification. The ability to infect root hairs and induce root nodule formation was investigated both using plant tests with the host plant Calliandra and PCR amplification of nodA and nodC genes for nodulation. The PGP activity of the strains was tested in vitro mainly with plate methods. The impact on growth, nitrogen content and nodulation in vivo was investigated through greenhouse experiments with the legumes Phaseolus vulgaris and Galega orientalis. Both the genetic and phenotypic diversity among the Stenotrophomonas strains was small, which proposes that they have the same origin. The strains brought about changes on the root hairs of Calliandra and they also increased the amount of root hairs. However, no root nodules were detected. The strains produced IAA, protease and lipase in vitro. They also showed plant a growth-promoting effect on G. orientalis, both alone and together with R. galegae HAMBI 540, and also activated nodulation among efficient rhizobia on P. vulgaris in greenhouse. It requires further research to get a better picture about the mechanisms behind the positive effects. The results in this thesis, however, confirm earlier studies concerning Stenotrophomonas positive impact on plants.

United We Stand - Divided We Fall : A Standard Model of Unit Cohesion

Research on unit cohesion has shown positive correlations between cohesion and valued outcomes such as strong performance, reduced stress, less indiscipline, and high re-enlistment intentions. However, the correlations have varied in strength and significance. The purpose of this study is to show that taking into consideration the multi-component nature of cohesion and relating the most applicable components to specific outcomes could resolve much of the inconsistency. Unit cohesion is understood as a process of social integration among members of a primary group with its leaders, and with the larger secondary groups of which they are a part. Correspondingly, included in the framework are four bonding components: horizontal (peer) and vertical (subordinate and leader) and organizational and institutional, respectively. The data were collected as part of a larger research project on cohesion, leadership, and personal adjustment to the military. In all, 1,534 conscripts responded to four questionnaires during their service in 2001-2002. In addition, sociometric questionnaires were given to 537 group members in 47 squads toward the end of their service. The results showed that platoons with strong primary-group cohesion differed from other platoons in terms of performance, training quality, secondary-group experiences, and attitudes toward refresher training. On the sociometric level it was found that soldiers who were chosen as friends by others were more likely to have higher expected performance, better performance ratings, more positive attitudes toward military service, higher levels of well-being during conscript service, and fewer exemptions from duty during it. On the group level, the selection of the respondents own group leader rather than naming a leader from outside (i.e., leader bonding) had a bearing not only on cohesion and performance, but also on the social, attitudinal, and behavioral criteria. Overall, the aim of the study was to contribute to the research on cohesion by introducing a model that takes into account the primary foci of bonding and their impact. The results imply that primary-group and secondary-group bonding processes are equally influential in explaining individual and group performance, whereas the secondary-group bonding components are far superior in explaining career intentions, personal growth, avoidance of duty, and attitudes toward refresher training and national defense. This should be considered in the planning and conducting of training. The main conclusion is that the different types of cohesion components have a unique, positive, significant, but varying impact on a wide range of criteria, confirming the need to match the components with the specific criteria.

Heating values of mature trees.

The effective heating values of the above and below ground biomass components of mature Scots pine (Pinus sylvestris), Norway spruce (Picea abies), downy birch (Betula pubescens), silver birch (Betula pendula), grey alder (Alnus incana), black alder (Alnus glutinosa) and trembling aspen (Populus tremula) were studied. Each sample tree was divided into wood, bark and foliage components. Bomb calorimetry was used to determine the calorimetric heating values. The species is a significant factor in the heating value of individual tree components. The heating value of the wood proper is highest in conifers. Broad-leaved species have a higher heating value of bark than conifers. The species factor diminishes when the weighted heating value of crown, whole stems or stump-root-system are considered. The crown material has a higher heating value per unit weight in comparison with fuelwood from small-sized stems or wholetrees. The additional advantages of coniferous crown material are that it is a non-industrial biomass resource and is readily available. The variability of both the chemical composition and the heating value is small in any given tree component of any species. However, lignin, carbohydrate and extractive content were found to vary from one part of the tree to another and to correlate with the heating value.

Comparative study of air heating solar collectors

Three types of conventional solar air heater are designed such that their heat absorbing areas and the pressure drops across them are equal for equal air mass flow rates per unit collector area. The results of thermal performance tests conducted simultaneously on these collectors, under the same environmental conditions, are presented.