Reactive Diffusion in the Re-Si System

A study on reactive diffusion is conducted in the Re-Si system. According to the study, ReSi1.8 phase grows with much higher thickness than the Re2Si phase, in the interdiffusion zone of bulk diffusion couples. The activation energy for integrated diffusion of ReSi1.8 is estimated to be 605 +/- 23 kJ/mol. The growth of the Re2Si phase is studied by considering an incremental diffusion couple of Re/ReSi1.8. Analysis based on the calculation of integrated diffusion coefficients indicates the reason underlying the observed high difference between the growth rates of the ReSi1.8 and Re2Si phases.

Cross-correlation-aided transport in stochastically driven accretion flows

The origin of linear instability resulting in rotating sheared accretion flows has remained a controversial subject for a long time. While some explanations of such non-normal transient growth of disturbances in the Rayleigh stable limit were available for magnetized accretion flows, similar instabilities in the absence of magnetic perturbations remained unexplained. This dichotomy was resolved in two recent publications by Chattopadhyay and co-workers Mukhopadhyay and Chattopadhyay, J. Phys. A 46, 035501 (2013); Nath et al., Phys. Rev. E 88, 013010 (2013)] where it was shown that such instabilities, especially for nonmagnetized accretion flows, were introduced through interaction of the inherent stochastic noise in the system (even a ``cold'' accretion flow at 3000Kis too ``hot'' in the statistical parlance and is capable of inducing strong thermal modes) with the underlying Taylor-Couette flow profiles. Both studies, however, excluded the additional energy influx (or efflux) that could result from nonzero cross correlation of a noise perturbing the velocity flow, say, with the noise that is driving the vorticity flow (or equivalently the magnetic field and magnetic vorticity flow dynamics). Through the introduction of such a time symmetry violating effect, in this article we show that nonzero noise cross correlations essentially renormalize the strength of temporal correlations. Apart from an overall boost in the energy rate (both for spatial and temporal correlations, and hence in the ensemble averaged energy spectra), this results in mutual competition in growth rates of affected variables often resulting in suppression of oscillating Alfven waves at small times while leading to faster saturations at relatively longer time scales. The effects are seen to be more pronounced with magnetic field fluxes where the noise cross correlation magnifies the strength of the field concerned. Another remarkable feature noted specifically for the autocorrelation functions is the removal of energy degeneracy in the temporal profiles of fast growing non-normal modes leading to faster saturation with minimum oscillations. These results, including those presented in the previous two publications, now convincingly explain subcritical transition to turbulence in the linear limit for all possible situations that could now serve as the benchmark for nonlinear stability studies in Keplerian accretion disks.

Stability of the flow in a soft tube deformed due to an applied pressure gradient

A linear stability analysis is carried out for the flow through a tube with a soft wall in order to resolve the discrepancy of a factor of 10 for the transition Reynolds number between theoretical predictions in a cylindrical tube and the experiments of Verma and Kumaran J. Fluid Mech. 705, 322 (2012)]. Here the effect of tube deformation (due to the applied pressure difference) on the mean velocity profile and pressure gradient is incorporated in the stability analysis. The tube geometry and dimensions are reconstructed from experimental images, where it is found that there is an expansion and then a contraction of the tube in the streamwise direction. The mean velocity profiles at different downstream locations and the pressure gradient, determined using computational fluid dynamics, are found to be substantially modified by the tube deformation. The velocity profiles are then used in a linear stability analysis, where the growth rates of perturbations are calculated for the flow through a tube with the wall modeled as a neo-Hookean elastic solid. The linear stability analysis is carried out for the mean velocity profiles at different downstream locations using the parallel flow approximation. The analysis indicates that the flow first becomes unstable in the downstream converging section of the tube where the flow profile is more pluglike when compared to the parabolic flow in a cylindrical tube. The flow is stable in the upstream diverging section where the deformation is maximum. The prediction for the transition Reynolds number is in good agreement with experiments, indicating that the downstream tube convergence and the consequent modification in the mean velocity profile and pressure gradient could reduce the transition Reynolds number by an order of magnitude.

Regeneration of Juvenile Woody Plants after Fire in a Seasonally Dry Tropical Forest of Southern India

Woody tree species in seasonally dry tropical forests are known to have traits that help them to recover from recurring disturbances such as fire. Two such traits are resprouting and rapid post-fire growth. We compared survival and growth rates of regenerating small-sized individuals (juveniles) of woody tree species after dry season fire (February-March) at eight adjacent pairs of burnt and unburnt transects in a seasonally dry tropical forest in southern India. Juveniles were monitored at 3-mo intervals between August 2009 and August 2010. High juvenile survivorship (>95%) was observed in both burnt and unburnt areas. Growth rates of juveniles, analyzed at the community level as well as for a few species individually (especially fast-growing ones), were distinctly higher in burnt areas compared to unburnt areas after a fire event, particularly during the pre-monsoon season immediately after a fire. Rapid growth by juveniles soon after a fire may be due to lowered competition from other vegetative forms such as grasses, possibly aided by the availability of resources stored belowground. Such an adaptation would allow a juvenile bank to be retained in the understory of a dry forest, from where individuals can grow to a possible fire-tolerant size during favorable conditions.

Orientation Selection and Microstructural Evolution in Directionally Solidified Tb0.3Dy0.7Fe1.95

Tb0.3Dy0.7Fe1.95 alloy was directionally solidified by using a modified Bridgman technique at a wide range of growth rates of 5 to 100 cm/h. The directionally grown samples exhibited plane front solidification morphology up to a growth rate of 90 cm/h. Typical island banding feature was observed closer to the chilled end, which eventually gave rise to irregular peritectic coupled growth (PCG). The PCG gained prominence with an increase in the growth rate. The texture study revealed formation of strong aOE (c) 311 > texture in a lower growth rate regime, aOE (c) 110 > and ``rotated aOE (c) 110 > aEuroe in an intermediate growth regime, and aOE (c) 112 > in a higher growth rate regime. In-depth analysis of the atomic configuration of a solid-liquid interface revealed that the growth texture is influenced by the kinetics of atomic attachment to the solid-liquid interface, which is intimately related to a planar packing fraction and an atomic stacking sequence of the interfacial plane. The mechanism proposed in this article is novel and will be useful in addressing the orientation selection mechanism of topologically closed packed intermetallic systems. The samples grown at a higher growth rate exhibit larger magnetostriction (lambda) and d lambda/dH owing to the absence of pro-peritectic (Tb,Dy)Fe-3 and formation of aOE (c) 112 > texture, which lies closer to the easy magnetization direction (EMD).

Strategic Marketing and Innovation Performance of Indian MSMEs

Micro Small and Medium Enterprises (MSMEs) is an integral part of the Indian industrial sector. The distinctive features of MSMEs are less capital investment and high labour absorption which has created unprecedented importance to this sector. As per the Development Commissioner of MSME, the sector has the credit of being the second highest in employment in India, which stands next to agricultural sector. The MSMEs are very much needed in efficiently allocating the enormous labour supply and scarce capital by implementing labour intensive production processes. Associated with this high growth rates, MSMEs are also facing a number of problems like sub-optimal scale of operation, technological obsolescence, supply chain inefficiencies, increasing domestic and global competition, fund shortages, change in manufacturing & marketing strategies, turbulent and uncertain market scenario. To survive with such issues and compete with large and global enterprises, MSMEs need to adopt innovative approaches in their regular business operations. Among the manufacturing sectors, we find that they are unable to focus themselves in the present competition. This paper presents a brief literature of work done in MSMEs, Innovation and Strategic marketing with reference to Indian manufacturing firms.

Morphological Evolution During Synthesis of New AlPO4 Center dot H2O Crystal

A new crystal of aluminophosphate, AIPO(4)(.)H(2)O, is synthesized from two-batch aqueous solution under hydrothermal conditions. Three types of the crystal habits, i.e. the tetragonal double pyramid, the tetragonal prism and the plate-type tetragonal prism, are found from batch-A solution. Two types of the crystal habits, i.e. the hexagonal pyramid and the strip-type tetragonal prism, are found from batch-B solution. The change of crystal morphology is originated from the fluctuation of the synthesis conditions, such as the supersaturation, the temperature and the impurity content. It causes change of the step energies, the defect density and the step roughness, and further, change of the growth rates. Since the crystal morphology is sensitive to the mass transport mechanism, the crystal habits could be changed under the microgravity.

High rate deposition of ta-C:H using an electron cyclotron wave resonance plasma source

A compact electron cyclotron wave resonance (ECWR) source has been developed for the high rate deposition of hydrogenated tetrahedral amorphous carbon (ta-C:H). The ECWR provides growth rates of up to 1.5 nm/s over a 4-inch diameter and an independent control of the deposition rate and ion energy. The ta-C:H was deposited using acetylene as the source gas and was characterized as having an sp3 content of up to 77%, plasmon energy of 27 eV, refractive index of 2.45, hydrogen content of about 30%, optical gap of up to 2.1 eV and RMS surface roughness of 0.04 nm. © 1999 Elsevier Science S.A. All rights reserved.

High rate deposition of Ta-C:H using an electron cyclotron wave resonance plasma source

A compact electron cyclotron wave resonance (ECWR) source has been developed for the high rate deposition of hydrogenated tetrahedral amorphous carbon (ta-C:H). The ECWR provides growth rates of up to 900 angstrom/min and an independent control of the deposition rate and ion energy. The ta-C:H was deposited using acetylene as the source gas and was characterized in terms of its bonding, stress and friction coefficient. The results indicated that the ta-C:H produced using this source fulfills the necessary requirements for applications requiring enhanced tribological performance.

The preparation, characterization and tribological properties of TA-C : H deposited using an electron cyclotron wave resonance plasma beam source

A compact electron cyclotron wave resonance (ECWR) source has been developed for the high rate deposition of hydrogenated tetrahedral amorphous carbon (ta-C:H). The ECWR provides growth rates of up to 900 Å/min over a 4″ diameter and an independent control of the deposition rate and ion energy. The ta-C:H was deposited using acetylene as the source gas and was characterized in terms of its sp3 content, mass density, intrinsic stress, hydrogen content, C-H bonding, Raman spectra, optical gap, surface roughness and friction coefficient. The results obtained indicated that the film properties were maximized at an ion energy of approximately 167 eV, corresponding to an energy per daughter carbon ion of 76 eV. The relationship between the incident ion energy and film densification was also explained in terms of the subsurface implantation of carbon ions into the growing film.

Evaluación del crecimiento y producción de turiones de espárrago verde (Asparagus officinalis L.) producidos bajo dos sistemas de inicio, arañas y plantines, en Azul, Buenos Aires

En dos plantaciones de espárrago verde (Asparagus officinalis L.) en el centro de la Pcia. de Buenos Aires, del cultivar UC 157 F2, iniciadas con arañas y plantines, durante su primer año de cosecha, se determinó la tasa de elongación diaria y total hasta el momento de la ramificación de los turiones, el número de días hasta alcanzar el largo exportable (22.5 cm) y los días hasta el momento de la ramificación con el objetivo de estudiar su comportamiento en la zona centro de la provincia de Buenos Aires. Las mediciones se efectuaron durante seis semanas, desde el 26 de septiembre hasta el 4 de noviembre de 2005, desde la emergencia del turión hasta el día de su ramificación (rama de 5 mm sobre su bráctea). La elongación máxima hasta el día de ramificación en promedio y para ambos sistemas de inicio, varió 2 desde 35.3 cm al principio de la cosecha hasta 22.8 cm al final de la misma. Las tasas de elongación relativas variaron en promedio para ambos sistemas de inicio, entre 0.11 cm cm-1 d-1 y 0.38 cm cm-1 d-1 dependiendo de la temperatura del aire. Al mismo tiempo las parcelas constituyentes del ensayo fueron sometidas a una cosecha comercial durante las seis semanas de evaluación. Los espárragos cosechados constituyeron el rendimiento total (kg ha-1) para cada sistema de inicio entre los cuales no se encontraron diferencias estadísticamente significativas. Este estudio permitiría explicar las diferencias de rendimiento comercial para un mismo cultivar en diferentes zonas de producción. Se concluye que para una zona dada, la elongación y sobre todo la ramificación, son variables prioritarias para la determinación del potencial productivo de un cultivar, debiendo tener en cuenta las condiciones de temperatura en las cual se pretende producir este cultivo y el mercado de destino de la producción debido a las mercadas preferencias entre sus consumidores.

杜仲抗真菌蛋白晶体生长的原子力显微成像研究—快速生长与晶面生长速率

杜仲抗真菌蛋白(Eucommiaantifungalprotein,EAFP)的单晶体具有在几小时内就可长大的快速生长特性.用原子力显微成像(atomicforcemicroscope,AFM)技术,原位实时观测了EAFP单斜晶体生长过程中的｛10 0｝表面形貌动态变化,并分别在不同的过饱和度下测量了其生长速率.结果表明,EAFP晶体生长的速率与蛋白质溶液的过饱和度相关,在过饱和度高时(σ =1 78)晶面生长极快;在中等过饱和度(σ =1 5)下,其晶面台阶的生长速率沿b,c方向分别为 12nm/s和 2 4 2nm/s,比溶菌酶生长速率(6～ 7nm/s)快很多;在蛋白质浓度很低的情况下,其生长速率仍与其他蛋白质相当.EAFP晶体快速生长可能与该分子尺寸较小,内部结构紧凑,分子骨架呈刚性和分子表面性质等其固有特性密切相关.沉淀剂浓度对EAFP晶体生长也有影响.过饱和度很低时,提高沉淀剂浓度会干扰晶体生长.

Microdamage Evolution, Energy Dissipation and Their Trans-Scale Effects on Macroscopic Failure

The process of damage evolution concerns various scales, from micro- to macroscopic. How to characterize the trans-scale nature of the process is on the challenging frontiers of solid mechanics. In this paper, a closed trans-scale formulation of damage evolution based on statistical microdamage mechanics is presented. As a case study, the damage evolution in spallation is analyzed with the formulation. Scaling of the formulation reveals that the following dimensionless numbers: reduced Mach number M, damage number S, stress wave Fourier number P, intrinsic Deborah number D*, and the imposed Deborah number De*, govern the whole process of deformation and damage evolution. The evaluation of P and the estimation of temperature increase show that the energy equation can be ignored as the first approximation in the case of spallation. Hence, apart from the two conventional macroscopic parameters: the reduced Mach number M and damage number S, the damage evolution in spallation is mainly governed by two microdamage-relevant parameters: the Deborah numbers D* and De*. Higher nucleation and growth rates of microdamage accelerate damage evolution, and result in higher damage in the target plate. In addition, the mere variation in nucleation rate does not change the spatial distribution of damage or form localized rupture, while the increase of microdamage growth rate localizes the damage distribution in the target plate, which can be characterized by the imposed Deborah number De*.

Nucleated polymerization with secondary pathways. I. Time evolution of the principal moments.

Self-assembly processes resulting in linear structures are often observed in molecular biology, and include the formation of functional filaments such as actin and tubulin, as well as generally dysfunctional ones such as amyloid aggregates. Although the basic kinetic equations describing these phenomena are well-established, it has proved to be challenging, due to their non-linear nature, to derive solutions to these equations except for special cases. The availability of general analytical solutions provides a route for determining the rates of molecular level processes from the analysis of macroscopic experimental measurements of the growth kinetics, in addition to the phenomenological parameters, such as lag times and maximal growth rates that are already obtainable from standard fitting procedures. We describe here an analytical approach based on fixed-point analysis, which provides self-consistent solutions for the growth of filamentous structures that can, in addition to elongation, undergo internal fracturing and monomer-dependent nucleation as mechanisms for generating new free ends acting as growth sites. Our results generalise the analytical expression for sigmoidal growth kinetics from the Oosawa theory for nucleated polymerisation to the case of fragmenting filaments. We determine the corresponding growth laws in closed form and derive from first principles a number of relationships which have been empirically established for the kinetics of the self-assembly of amyloid fibrils.

Aquatic Vegetation, Largemouth Bass and Water Quality Responses to Low-Dose Fluridone Two Years Post Treatment

Whole-lake techniques are increasingly being used to selectively remove exotic plants, including Eurasian watermilfoil ( Myriophyllum spicatum L.). Fluridone (1-methyl-3-phenyl- 5-[3-(trifluoromethyl)phenyl]-4(1 H )-pyridinone), a systemic whole-lake herbicide, is selective for Eurasian watermilfoil within a narrow low concentration range. Because fluridone applications have the potential for large effects on plant assemblages and lake food webs, they should be evaluated at the whole-lake scale. We examined effects of low-dose (5 to 8 ppb) fluridone applications by comparing submersed plant assemblages, water quality and largemouth bass ( Micropterus salmoides ) growth rates and diets between three reference lakes and three treatment lakes one- and two-years post treatment. In the treatment lakes, fluridone reduced Eurasian watermilfoil cover without reducing native plant cover, although the duration of Eurasian watermilfoil reduction varied among treatment lakes. (PDF has 11 pages.)