Some solutions to obtain very efficient separations in isocratic and gradient modes using small particles size and ultra-high pressure.

The UHPLC strategy which combines sub-2 microm porous particles and ultra-high pressure (>1000 bar) was investigated considering very high resolution criteria in both isocratic and gradient modes, with mobile phase temperatures between 30 and 90 degrees C. In isocratic mode, experimental conditions to reach the maximal efficiency were determined using the kinetic plot representation for DeltaP(max)=1000 bar. It has been first confirmed that the molecular weight of the compounds (MW) was a critical parameter which should be considered in the construction of such curves. With a MW around 1000 g mol(-1), efficiencies as high as 300,000 plates could be theoretically attained using UHPLC at 30 degrees C. By limiting the column length to 450 mm, the maximal plate count was around 100,000. In gradient mode, the longest column does not provide the maximal peak capacity for a given analysis time in UHPLC. This was attributed to the fact that peak capacity is not only related to the plate number but also to column dead time. Therefore, a compromise should be found and a 150 mm column should be preferentially selected for gradient lengths up to 60 min at 30 degrees C, while the columns coupled in series (3x 150 mm) were attractive only for t(grad)>250 min. Compared to 30 degrees C, peak capacities were increased by about 20-30% for a constant gradient length at 90 degrees C and gradient time decreased by 2-fold for an identical peak capacity.

The in vivo performance of magnetic particle-loaded injectable, in situ gelling, carriers for the delivery of local hyperthermia.

We investigated the use of in situ implant formation that incorporates superparamagnetic iron oxide nanoparticles (SPIONs) as a form of minimally invasive treatment of cancer lesions by magnetically induced local hyperthermia. We developed injectable formulations that form gels entrapping magnetic particles into a tumor. We used SPIONs embedded in silica microparticles to favor syringeability and incorporated the highest proportion possible to allow large heating capacities. Hydrogel, single-solvent organogel and cosolvent (low-toxicity hydrophilic solvent) organogel formulations were injected into human cancer tumors xenografted in mice. The thermoreversible hydrogels (poloxamer, chitosan), which accommodated 20% w/v of the magnetic microparticles, proved to be inadequate. Alginate hydrogels, however, incorporated 10% w/v of the magnetic microparticles, and the external gelation led to strong implants localizing to the tumor periphery, whereas internal gelation failed in situ. The organogel formulations, which consisted of precipitating polymers dissolved in single organic solvents, displayed various microstructures. A 8% poly(ethylene-vinyl alcohol) in DMSO containing 40% w/v of magnetic microparticles formed the most suitable implants in terms of tumor casting and heat delivery. Importantly, it is of great clinical interest to develop cosolvent formulations with up to 20% w/v of magnetic microparticles that show reduced toxicity and centered tumor implantation.

Elaboració de membranes de fibra buida modificades amb nanopartícules metàl·liques per aplicacions catalítiques

Investigación producida a partir de una estancia en la Université Paul Sabatier, Toulouse III - CNRS, entre 2007 y 2009. Durante los últimos años la investigación centrada en nuevos materiales de tamaño nanoscòpico (nanopartículas, quantum dots, nanotubos de carbono,...) ha experimentado un crecimiento considerable debido a las especiales propiedades de los "nanoobjetos" con respecto a magnetismo, catálisis, conductividad eléctrica, etc ... Sin embargo, hoy en día todavía existen pocas aplicaciones de las nanopartículas en temas medioambientales. Uno de los motivos de esta situación es la posible toxicidad de los nanoobjetos, pero existe también una dificultad tecnológica dado que las nanopartículas tienden a agregarse y es muy difícil manipularlas sin que pierdan sus propiedades especiales. Así, aunque la preparación de materiales catalíticos nanoestructurados es muy interesante, es necesario definir nuevas estrategias para prepararlos. Este proyecto de investigación tiene como objetivo principal la preparación de nuevas membranas catalíticas con nanopartículas metálicas en el interior para aplicaciones de tratamiento de agua. La innovación principal de este proyecto consiste en que las nanopartículas no son introducidas en la matriz polimérica una vez preformadas sino que se hacen crecer en el interior de la matriz polimérica mediante una síntesis intermatricial. El único requisito es que la matriz polimérica contenga grupos funcionales capaces de interaccionar con los precursores de las nanopartículas. Una vez finalizado el proyecto se puede afirmar que se han logrado parte de los objetivos planteados inicialmente. Concreamente ha quedado demostrado que se pueden sintetizar nanopartículas metálicas de metales nobles (platino y paladio) en membranas de fibra hueca de micro- y ultrafiltración siguiendo dos metodologías diferentes: modificación fotoquímica de polímeros y deposición de multicapas de polielectrolitos. Los nuevos materiales son efectivos en la catálisis de reducción de un compuesto modelo (4-nitrofenol con borohidruro de sodio) y, en general, los resultados han sido satisfactorios. Sin embargo, se ha puesto de manifiesto que el uso de un reactivo que genera hidrógeno gas en contacto con la solución acuosa dificulta enormemente la implementación de la reacción catalítica al ser el medio de la membrana una matriz porosa. Así, como conclusión principal se puede decir que se han encontrado las limitaciones de esta aproximación y se sugieren dos posibilidades de continuidad: la utilización de las membranas sintetizadas en contactores gas-líquido o bien el estudio y optimización del sistema de membrana en configuración de membranas planas, un objetivo más asequible dada su menor complejidad. Esta investigación se ha realizado en el seno del “Laboratoire de Génie Chimique” de Toulouse y del Departamento de Química de la Michigan State University y ha sido posible gracias a un proyecto financiado por la “Agence National pour la Recherce” y al programa PERMEANT entre el CNRS y la NSF.

External morphology of sensory structures of fourth instar larvae of neotropical species of phlebotomine sand flies (Diptera: Psychodidae) under scanning electron microscopy

In the present study, some morphological structures of antennae, maxillary palps and caudal setae of fourth instar larvae of laboratory-reared phlebotomine sand flies (Lutzomyia longipalpis, L. migonei, L. evandroi, L. lenti, L. sericea, L. whitmani and L. intermedia) of the State of Ceará, Brazil, were examined under scanning electron microscopy. The antennal structures exhibited considerable variation in the morphology and position. A prominent digitiform distal segment has been observed only on the antenna of species of the subgenus Nyssomyia. The taxonomic relevance of this and other antennal structure is discussed. The papiliform structures found in the maxillae and the porous structures of the caudal setae of all species examined may have chemosensory function. Further studies with transmission electron microscopy are needed to better understand the physiological function of these external structures.

Prenatally engineered autologous amniotic fluid stem cell-based heart valves in the fetal circulation.

Prenatal heart valve interventions aiming at the early and systematic correction of congenital cardiac malformations represent a promising treatment option in maternal-fetal care. However, definite fetal valve replacements require growing implants adaptive to fetal and postnatal development. The presented study investigates the fetal implantation of prenatally engineered living autologous cell-based heart valves. Autologous amniotic fluid cells (AFCs) were isolated from pregnant sheep between 122 and 128 days of gestation via transuterine sonographic sampling. Stented trileaflet heart valves were fabricated from biodegradable PGA-P4HB composite matrices (n = 9) and seeded with AFCs in vitro. Within the same intervention, tissue engineered heart valves (TEHVs) and unseeded controls were implanted orthotopically into the pulmonary position using an in-utero closed-heart hybrid approach. The transapical valve deployments were successful in all animals with acute survival of 77.8% of fetuses. TEHV in-vivo functionality was assessed using echocardiography as well as angiography. Fetuses were harvested up to 1 week after implantation representing a birth-relevant gestational age. TEHVs showed in vivo functionality with intact valvular integrity and absence of thrombus formation. The presented approach may serve as an experimental basis for future human prenatal cardiac interventions using fully biodegradable autologous cell-based living materials.

Activity and Residual Effect of Two Formulations of Lambdacyhalothrin Sprayed on Palm Leaves to Rhodnius prolixus

The insecticidal activity and residual effect of two formulations of lambdacyhalothrin were evaluated with Rhodnius prolixus;laboratory and field tests were conducted in the State of Chiapas, Mexico. The results indicate that the lethal concentrations of the active ingredient of SC (LC50 = 2.37 and LC90 = 8.5 mg, a.i./m²) were 4-8 times than those with the insecticide WP applied on R. prolixus bugs in palm leaves, a common building material for thatched roofs. Other investigators in South America recommended applying 30 mg a.i./m² in porous materials; we obtained that the products WP and SC were 3.5 and 16 times more effective on palm leaves. Regarding the evaluation of the residual effects in field spraying, there was up to 15 months persistence after the application of WP in two doses (8.6 mg a.i./m² and 3.752 mg a.i./m²) with SC. We consider R. prolixus highly susceptible to the employed pyrethroids; they could be used to control this vector in the state of Chiapas, Mexico.

Fipronil Insecticide: Novel Application against Triatomine Insect Vectors of Chagas Disease

We investigated the efficacy and the residual effect of fipronil® against two species of triatomine bugs, Triatoma infestans and Rhodnius neglectus, in laboratory conditions measuring concentration-response and residual activity on different surfaces (dried mud and lime coated mud). Lethal concentrations (LC50,90) were determined on filter paper. The higher insecticide efficacy against R. neglectus when compared to T. infestans may be partially attributed to the differences in their biological cycles and genetic structures. Comparison with lambdacyhalothrin wettable powder showed that fipronil mortality rates (above 50%) were observed on mud blocks and lime-coated mud blocks up to 3 months when fipronil was sprayed at 100 and 200 mg a.i./m². Residual effect deeply decayed after 3 months; and at 6 months post treatment mortality was not observed. In contrast, lambdacyhalothrin showed a long lasting residual effect on both surfaces up to 6 months. Also, it should be mentioned that fipronil had a slow, but lethal activity on the triatomine bugs when wettable formulations were used on porous surfaces.

Comparative evaluation of pyrethroid insecticide formulations against Triatoma infestans (Klug): residual efficacy on four substrates

We investigated the residual efficacy of four insecticide formulations used in Chagas disease vector control campaigns: cyfluthrin 12.5% suspension concentrace (SC), lambda-cyhalothrin 10% wettable powder (WP), deltamethrin 2.5% SC, and 2.5% WP on four types of circular blocks of wood, straw with mud, straw with mud painted with lime, and mud containing 5% of cement. Three concentrations of these insecticides were tested: the LC90 (previously determined on filter paper), the double of the LC90, and the recommended operational dose. For each bioassay test, 15 third-stage nymphs of Triatoma infestans (Klug) (Hemiptera: Reduviidae) were exposed for 120 h to each treatment at 24 h, 30, 60, 90, and 180 days post-spraying. Mortality rates, moulting history and behaviour were recorded at 24, 48, 72, and 120 h of exposure. Mortality rates were highest during the first 30 days post-spraying. Highest mortality rates (above 50%) were observed for deltamethrin 2.5% SC and lambda-cyhalothrin 10% WP on wood blocks up to three months post-spraying. Mud was the substrate on which treatments showed lowest persistence, with the other two substrates showing intermediate residual efficacy of all treatments. During the first 30 days WP formulations were not as effective as SC flowable formulations but, overall in the longer term, WP gave grater mortality rates of T. infestans nymphs exposed at up to six months post-spraying. Porous surfaces, especially mud, showed most variability presumably due to absorption of the insecticide. In contrast the less porous surfaces (i.e. wood and lime-coated mud) kept mortality rates high for longer post-treatment, irrespective of the insecticide concentration used.

Wet chemical silver treatment of endotracheal tubes to produce antibacterial surfaces.

Mechanically ventilated patients in hospitals are subjected to an increased risk of acquiring nosocomial pneumonia that sometimes has a lethal outcome. One way to minimize the risk could be to make the surfaces on endotracheal tubes antibacterial. In this study, bacterial growth was inhibited or completely prevented by silver ions wet chemically and deposited onto the tube surface. Through the wet chemical treatment developed here, a surface precipitate was formed containing silver chloride and a silver stearate salt. The identity and morphology of the surface precipitate was studied using x-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, scanning electron microscopy, and x-ray powder diffraction. Leaching of silver ions into solution was examined, and bacterial growth on the treated surfaces was assayed using Pseudomonas aeruginosa wild type (PAO1) bacteria. Furthermore, the minimum inhibitory concentration of silver ions was determined in liquid- and solid-rich growth medium as 23 and 18 microM, respectively, for P. aeruginosa.

Use of a saline gradient for the diagnosis of schistosomiasis

The development of novel methods for parasitological diagnosis that are both highly sensitive and low in cost has been strongly recommended by the World Health Organization. In this study, a new technique for diagnosis of schistosomiasis mansoni is proposed based on the differential sedimentation of eggs when subjected to a slow continuous flux of 3% saline solution through a porous plaque. This influx suspends low-density faecal material, effectively cleaning the sample. The remaining sediment covering the porous plaque surface is then transferred to a glass slide and examined under a bright field microscope. Twelve Kato-Katz slides were used for comparison in the present study. Our results suggest that the saline gradient method detects a signifi-cantly higher number of eggs than the 12 Kato-Katz slides (p < 0.0001). We also found microscopic inspection to be quicker and easier with our newly described method. After cleaning the sample, the obtained sediment can also be conserved in a 10% formaldehyde solution and examined for at least 45 days later without statistically significant egg count differences.

Histological and histochemical evaluation of human oral mucosa constructs developed by tissue engineering

Reconstruction of large oral mucosa defects is often challenging, since the shortage of healthy oral mucosa to replace the excised tissues is very common. In this context, tissue engineering techniques may provide a source of autologous tissues available for transplant in these patients. In this work, we developed a new model of artificial oral mucosa generated by tissue engineering using a fibrin-agarose scaffold. For that purpose, we generated primary cultures of human oral mucosa fibroblasts and keratinocytes from small biopsies of normal oral mucosa using enzymatic treatments. Then we determined the viability of the cultured cells by electron probe quantitative X-ray microanalysis, and we demonstrated that most of the cells in the primary cultures were alive and had high K/Na ratios. Once cell viability was determined, we used the cultured fibroblasts and keratinocytes to develop an artificial oral mucosa construct by using a fibrin-agarose extracellular matrix and a sequential culture technique using porous culture inserts. Histological analysis of the artificial tissues showed high similarities with normal oral mucosa controls. The epithelium of the oral substitutes had several layers, with desmosomes and apical microvilli and microplicae. Both the controls and the oral mucosa substitutes showed high suprabasal expression of cytokeratin 13 and low expression of cytokeratin 10. All these results suggest that our model of oral mucosa using fibrin-agarose scaffolds show several similarities with native human oral mucosa.

Fingermark detection based on the in situ growth of luminescent nanoparticles: towards a new generation of multimetal deposition

The in situ deposition of zinc oxide on gold nanoparticles in aqueous solution has been here successfully applied in the field of fingermark detection on various non-porous surfaces. In this article, we present the improvement of the multimetal deposition, an existing technique limited up to now to non-luminescent results, by obtaining luminescent fingermarks with very good contrast and details. This is seen as a major improvement in the field in terms of selectivity and sensitivity of detection, especially on black surfaces.

Construcció d'un elèctrode d'ió selectiu amb membrana de PVC i marro de cafè com a ionòfor

Els elèctrodes són instruments d’anàlisi molt emprats per la seva gran eficiència, fàcil utilització, de resposta “in situ” i que ocupen poc espai. Tot i això, existeix una problemàtica actual dels elèctrodes, que és la no comercialització d’elèctrodes per tots els metalls que trobem dissolts en solucions d’interès analític. Per aquest motiu s’estudien possibles substàncies dins la formació de la membrana dels elèctrodes, ionòfors, que reaccionin amb espècies iòniques amb inexistència d’elèctrodes comercials. S’han dut a terme estudis amb residus vegetals com a ionòfors. Algunes dels biomaterials estudiats són la rapa i la iohimbe per a la detecció del Cr(VI) i l’Hg(II). Aquestes han sigut les motivacions que han dut a construir un elèctrode de ió selectiu amb membrana de PVC i marro de cafè com a ionòfor, i seguidament avaluar-ne laseva resposta

Adsorció de crom (VI) i crom (III) en solució amb closca de cranc

En l’eliminació del crom en suspensió de les aigües residuals de les indústries es realitzen dos processos: una precipitació en medi àcid on es redueix el crom (VI) a crom (III) en què s’elimina la major part del crom, i el següent tractament es fa per bescanvi iònic o per adsorció. Els adsorbents emprats actualment tenen un elevat cost i s’està estudiant nous adsorbents, com a substituts dels tradicionals, de baix cost. Dins d’aquest adsorbents de baix cost es troben els bioadsorbents, biomaterials amb gran capacitat d’adsorció. L’objectiu del projecte es va centrar en l’estudi de l’adsorció de crom trivalent i hexavalent en solucions aquoses utilitzant com a adsorbent el residu industrial de closca de cranc, provinent d’una indústria alimentària de barretes de cranc