Bonding of Y-TZP to Dentin: Effects of Y-TZP Surface Conditioning, Resin Cement Type, and Aging

Purpose: To evaluate the effects of two surface treatments, aging, and two resin cements on shear bond strength between dentin and yttrium-stabilized tetragonal zirconia polycrystal ceramic (Y-TZP).Materials and Methods: Eighty human molars were embedded in acrylic resin and sectioned 3 mm below the occlusal plane. These teeth and 80 cylindrical Y-TZP specimens (height, 4 mm; diameter, 3.4 mm) were divided into eight groups (n=10) using the following factors: Y-TZP surface treatment (Vi: low-fusing porcelain [vitrification] + hydrofluoric acid etching + silanization or Si: tribochemical silicatization); cementation strategies (PF: Pan avia or CC: Clearfil); and storage (nonaging or aging). Bonding surfaces of 40 Y-TZP specimens received Vi treatment, and the rest received Si treatment. Half of the ceramic-tooth assemblies were cemented with Panavia, the rest with Clearfil. Shear tests were executed using 0.4-mm-thick wire at 0.5 mm/min. Data were analyzed by three-way analysis of variance and Tukey test (alpha=0.05). Fractures were analyzed.Results: Y-TZP surface treatments did not affect bond strength (p=0.762, Vi = Si), while resin cements (p<0.001, Panavia > Clearfil) and aging (p=0.006, nonaging > aging) showed a significant effect. Most failures were in adhesive at dentin-cement interfaces; no failure occurred between zirconia and cement.Conclusion: When Y-TZP ceramic is bonded to dentin, the weakest interface is that between dentin and resin cement. The resin cement/Y-TZP interface was less susceptible to failures, owing to Y-TZP surface treatments.

JUVENILE DEVELOPMENT OF DILOCARCINUS PAGEI STIMPSON, 1861 (BRACHYURA, TRICHODACTYLIDAE) REARED IN THE LABORATORY, WITH EMPHASIS ON SETAE MORPHOLOGY

The juvenile development of the freshwater crab Dilocarcinus pagei Stimpson, 1861 was studied under laboratory conditions, focusing on setae morphology. The ovigerous females were collected manually associated with water hyacinth at the Municipal Dam of Sao Jose do Rio Preto (Sao Paulo, Brazil). The specimens were raised in the laboratory under constant aeration, photoperiod (12: 12 h) and temperature (27 +/- 1 degrees C). Twelve juvenile stages were obtained with descriptions of the main morphological characters that allow their identification are presented. Fourteen types of setae were discovered: dentate, denticulate, serrulate, papposerrate, cuspidate, plumose, plumodenticulate, plumoserrulate, simple, pappose, brush, curved, nail and setules. The greatest diversity of setae was found on the mouth appendages, especially the maxillule. The gill ontogeny and sexual dimorphism becomes apparent from the second juvenile stage onwards. At the third juvenile stage, the carapace begins to exhibit a wider shape, becoming similar to that of the adults.

Intraspecific, interspecific, and seasonal differences in the diet of three mid-sized carnivores in a large neotropical wetland

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Biologia e ecologia de ermitões (Crustacea, Anomura) do sublitoral não consolidado do sudeste brasileiro

Pós-graduação em Ciências Biológicas (Zoologia) - IBB

Efeito dos tratamentos de superfície na resistência da união porcelana/cimento resinoso

Pós-graduação em Odontologia Restauradora - ICT

Avaliação do tipo de carregamento, pela análise de elementos finitos, sobre a resistência de união ao cisalhamento da interface metal/porcelana (Ni-Cr/vita omega 900)

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Avaliação laboratorial da resistência ao cisalhamento de discos de porcelana e de um polímero de vidro cimentados à dentina bovina com o emprego de cimentos adesivos

Pós-graduação em Odontologia Restauradora - ICT

Distribuição das tensões em próteses protocolo mandibulares com diferentes extensões de cantilever e material de revestimento oclusal

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

18-Year Follow-up of Dens Invaginatus: Retrograde Endodontic Treatment

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Repair Technique for Fractured Implant-Supported Metal-Ceramic Restorations: A Clinical Report

The fracture of porcelain structures have been related in either natural dentition or implant-supported restorations. Techniques using a composite resin or indirect methods can be used. This article presents a porcelain fracture on implant-supported metal-ceramic restoration. IPS Empress e.max laminate veneer restoration was used to repair the fracture. With this technique, it was possible to restore aesthetics and function, combined with low cost and patient satisfaction.

Evaluation of tensile tetention of Y-TZP crowns after long-term aging: Effect of the core substrate and crown surface conditioning

This study evaluated the effect of the core substrate type (dentin and composite resin) on the retention of crowns made of yttrium oxide stabilized tetragonal zirconia polycrystal (Y-TZP), submitted to three inner surface conditionings. For this purpose, 72 freshly extracted molars were embedded in acrylic resin, perpendicular to the long axis, and prepared for full crowns: 36 specimens had crown preparations in dentin; the remaining 36 teeth had the crowns removed, and crown preparations were reconstructed with composite resin plus fiber posts with dimensions identical to the prepared dentin. The preparations were impressed using addition silicone, and 72 Y-TZP copings for the tensile test were produced. Cementation was performed with a dual-cured cement containing phosphate monomers. For cementation, the crown preparation (dentin or resin) was conditioned with the adhesive system, and the ceramic was subjected to one of three surface treatments: isopropyl alcohol, tribochemical silica coating, or thin low-fusing glassy porcelain layer application plus silanization. After 24 hours, all specimens were submitted to thermocycling (6000 cycles) and placed in a special tensile testing device in a universal testing machine to determine failure loads. The failure modes of all samples were analyzed under a stereomicroscope. Two-way analysis of variance showed that the surface treatment and substrate type (alpha=0.05) affected the tensile retention results. The dentin substrate presented the highest tensile retention values, regardless of the surface treatment. When the substrate was resin, the tribochemical silica coating and low-fusing glaze application plus silanization groups showed the higher retention values.

GASTROPOD SHELLS USED BY Dardanus insignis (Decapoda, Anomura) NEAR ISLANDS IN THE UBATUBA REGION, SAO PAULO, BRAZIL

The use of gastropod shells by hermit crabs is determined by the availability of shells in the environment or through selection for size and volume. This study analyzed patterns in the use of shells by Dardanus insignis (Saussure, 1858). From January 1998 to December 1999, 386 individuals were collected from two islands at Ubatuba, Sao Paulo. The crabs were measured for cephalothoracic shield length (CSL) and wet weight (CWW). The gastropod shells occupied by hermit crabs were identified, and the shell aperture width (SAW), dry weight (SDW) and internal volume (STY) were measured. The relationships between the dimensions of the gastropod shell and the hermit crabs were evaluated by linear regression analysis. Among the 11 species of gastropod shells used by D. insignis, the most often used was Olivancillaria urceus (31%), followed by Strombus pugilis (22%) and Siratus tenuivaricosus (18%). The shell of O. urceus was used most probably due to its high availability on Couves and Mar Virado islands. The most significant biometric parameter was shell aperture width (F=18.231; p<0.0001), highlighting the importance of this variable for the shell choice by D. insignis at both sites.

Avaliação do tempo e da concentração do condicionamento com ácido fluorídrico sobre a resistência de união entre cerâmica e cimento resinoso

The aim of this study was to verify through microtensile test the influence of time and concentration of surface conditioning with hydrofluoric acid and its interference in the adhesion of dual resin cement to porcelain.We used 32 bodies of glass-ceramic lithium disilicate system IPS e.max Press LT with dimensions of 6mm thick, 8 mm in length and 8 mm in length, which will be molded to obtain composite resin blocks corresponding to blocks ceramics. Ceramic and resin blocks were divided into 16 groups (n = 4) and numbered according to the concentration of hydrofluoric acid (2.5%, 5%, 7.5% and 10%) and conditioning time (20 seconds, 40 seconds, 1 minute and 2 minutes). The blocks were cleaned in ultrasonic apparatus with distilled water and dried with compressed air, subjected to acid etching and air-jet washed with water, dried with compressed air and received application of silane agent Monobond-S, followed by adhesive Excite ( Ivoclar Vivaden). Each ceramic block was bonded to the corresponding block of resin through the resin cement Multilink Automix. The specimens were cut to obtain nine micro samples for each set of ceramic-resin with 1 mm X 1 mm X 12 mm in length, which were submitted to microtensile test. The results were analyzed with descriptive statistics and analysis of variance with significance level of 5%, revealing that there were statistically significant (p = 0.000001 <0.05). From the Tukey test can be concluded that etching with hydrofluoric acid and 2.5% for 120 seconds gave the best bond strength, however, no statistical difference between the conditioning with the same acid in the concentration of 5.0% for 20 to 40 seconds

Impacto geno e citotóxico em populações do caranguejo-uçá, Ucides cordatus (Linnaeus, 1763) (Crustacea, Brachyura, Ucididae), em manguezais do estado de São Paulo, Brasil

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Determinação do tempo de vida de restaurações totalmente cerâmicas (y-tzp/porcelana) com incidência da carga em diferentes regiões de contato

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)