Study of polypropylene surface modification by air dielectric barrier discharge operated at two different frequencies

In this work, air dielectric barrier discharge (DBD) operating at the line frequency (60 Hz) or at frequency of 17 kHz was used to improve the wetting properties of polypropylene (PP). The changes in the surface hydrophilicity were investigated by contact angle measurements. The plasma-induced chemical modifications of PP surface were studied by X-ray photoelectron spectroscopy (XPS) and Fourier-transformed infrared spectroscopy (FTIR). The polymer surface morphology and roughness before and after the DBD treatment were analyzed by atomic force microscopy (AFM). To compare the plasma treatment effect at different frequencies the variation of the contact angle is presented as a function of the deposited energy density. The results show that both DBD treatments leaded to formation of water-soluble low molecular weight oxidized material (LMWOM), which agglomerated into small mounts on the surface producing a complex globular structure. However, the 60 Hz DBD process produced higher amount of LMWOM on the PP surface comparing to the 17 kHz plasma treatment with the same energy dose. The hydrophilic LMWOM is weakly bounded to the surface and can be easily removed by polar solvents. After washing the DBD-treated samples in de-ionized water their surface roughness and oxygen content were reduced and the PP partially recovered its original wetting characteristics. This suggested that oxidation also occurred at deeper and more permanent levels of the PP samples. Comparing both DBD processes the 17 kHz treatment was found to be more efficient in introducing oxygen moieties on the surface and also in improving the PP wetting properties. © 2012 Elsevier B.V. All rights reserved.

Model to design drip hose lateral line using two spacing between emitters

The use of non-pressure compensating drip hose in horticultural and annual cycle fruits is growing in Brazil. In this case, the challenge for designers is getting longer lateral lines with high values of uniformity. The objective of this study was to develop a model to design longer lateral lines using non-pressure compensating drip hose. Using the developed model, the hypotheses to be evaluated were: a) the use of two different spacing between emitters in the same lateral line allows longer length; b) it is possible to get longer lateral lines using high values of pressure variation in the lateral lines since the distribution uniformity stays below allowable limits. A computer program was developed in Delphi based on the model developed and it is able to design lateral lines in level using non-pressure compensating drip hose. The input data are: desired distribution uniformity (DU); initial and final pressure in the lateral line; coefficients of relationship between emitter discharge and pressure head; hose internal diameter; pipe cross-sectional area with the dripper; and roughness coefficient for the Hazen-Williams equation. The program allows calculate the lateral line length with three possibilities: selecting two spacing between emitters and defining the exchange point; using two pre-established spacing between emitters and calculating the length of each section with different spacing; using one emitter spacing. Results showed that the use of two sections with different spacing between drippers in the lateral line didn't allow longer length but got better uniformity when compared with lateral line with one spacing between emitters. The adoption of two spacing increased the flow rate per meter in the final section which represented approximately 80% of the lateral line total length and this justifies their use. The software allowed DU above 90% with pressure head variation of 40% and the use of two spacing between emitters. The developed model/software showed to be accurate, easy to handle and useful for lateral line design using non-pressure compensating drip hose.

Continuous production of metal matrix composites from the semisolid state

Continuous strip metal matrix composite (MMC) casting of 0.3 mm diameter hard-drawn stainless steel (316L) wire in a quasi-eutectic SnPb (64Sn36Pb) matrix was performed by a two-roll melt drag processing (TRMDping) method, with the wire being dragged through a semisolid puddle with a fibre contact time of approximately 0.2 s. A slag weir placed at the nozzle contained two wire guide holes: one located near the upper roll, and the other located between the rolls. A successful continuous composite strip casting with good fibre alignment was achieved by inserting and embedding the wire into the matrix using the guide hole between the rolls. Degeneration of eutectic/dendrite structures led to the formation of globular structures. The occurrence and formation mechanisms of cracks, de-lamination and voids in the matrix were discussed. TRMDping is economically viable and has significant benefits over other MMC fabrication methods. © (2013) Trans Tech Publications, Switzerland.

Human rights and the child

Includes bibliography

Argentina: households and labour market changes (2004-2009)

Includes bibliography

Suplementação alimentar com ácidos graxos essenciais para tilápias do Nilo: desempenho produtivo, hematológico e granuloma por corpo estranho

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Alterações hematológicas e hormonais em fêmeas de jundiá (Rhamdia quelen) provocadas por estresse mecânico e contaminação da água por herbicida a base de glifosato

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo conformacional de polianfóteros fracos utilizando simulações de Monte Carlo

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Interação do peptídeo MP-I com micela de SDS em solução aquosa: um estudo por dinâmica molecular

Pós-graduação em Biofísica Molecular - IBILCE

Óleo de Neem: tratamento parasitário em ovinos e desenvolvimento ponderal

Pós-graduação em Ciência Animal - FMVA

Variação da ecogenicidade difusa em parênquima hepático homogêneo relacionada aos achados bioquímicos e hematológicos em cães

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Estudo eritroleucométrico e proteinograma do sangue do cordão umbilical e da jugular de eqüinos e asininos ao nascimento e de suas respectivas mães

Pós-graduação em Cirurgia Veterinária - FCAV

Avaliações clínicas e metabólicas de cavalos da raça Árabe submetidos a exercício progressivo em esteira

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Estudo cardiorrespiratório comparativo da anestesia geral inalatória com o sevofluorano em cadela não-gestantes e no terço final da gestação, pré-tratados com acepromazina e propofol

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Avaliação da passagem transplacentária e colostral de cobre e seus principais antagonistas em cordeiros e ovelhas da raça Bergamácia

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)