Austrian glacier inventory 1969 (G I)

The Austrian glacier inventory 1969 was compiled from airborne photogrammetry dating from September and October 1969. It includes not only area and surface elevation, but also a number of other parameters as aspect, maximum and minimum elevation, position, ablation and accumulation area. The dataset published here are the orginal results. In course of the compilation of the second Austrian glacier inventory, the photogrammetric data partly has been reanalysed. While in this data set snow areas connected to the glaciers and snow patches in the upper parts of the glacier have not been added to the glacier area, the second glacier inventory included the snow patches.

On the structure of the floating zone in melting

Floating zone melting is used in crystal growth and purification of high melting materials. The use of a reduced gravity environment will remove the constraint imposed on the length of the zone by the hydrostatic pressure. The equilibrium of the fioatmg zone may involve, (1)Hydrostatic forces, when the zone rotates as a whole. (2)Convective driving forces, when the zone is stationary but fluid property gradients appear.(3) Hydrodynamic forces, when some parts of the zone are set into motion with respect to others. The last effects are considered in this paper. The flow pattern of a floating zone held between two discs in relative motion is complicated, and thence the solution of the problem is difficult even assuming a constant property-newtonian liquid Nevertheless, when a small parameter appears m the problem, the complete flow field can be split into zones where simple solutions are found. To illustrate this approach, the spin up from rest of an initially cylindrical floating zone is considered with detail. Here the small parameter is the time elapsed from the impulsive starting of motion. Since the problem which has been considered, as well as some others which can be tackled by use of similar methods, concern the viscous layer close to either plate, they can be simulated experimentally in the ground laboratory with short floating zones. Procedures to produce these zones are indicated.

Surface velocity and ice discharge of the ice cap on King George Island, Antarctica

Glaciers on King George Island, Antarctica, have shown retreat and surface lowering in recent decades, concurrent with increasing air temperatures. A large portion of the glacier perimeter is ocean-terminating, suggesting possible large mass losses due to calving and submarine melting. Here we estimate the ice discharge into the ocean for the King George Island ice cap. L-band synthetic aperture radar images covering the time-span January 2008 to January 2011 over King George Island are processed using an intensity-tracking algorithm to obtain surface velocity measurements. Pixel offsets from 40 pairs of radar images are analysed and inverted to estimate a weighted average surface velocity field. Ice thicknesses are derived from simple principles of ice flow mechanics using the computed surface velocity fields and in situ thickness data. The maximum ice surface speeds reach mayor que 225 m/yr, and the total ice discharge for the analysed flux gates of King George Island is estimated to be 0.720+/-0.428 Gt/yr, corresponding to a specific mass loss of 0.64+/-0.38 m w.e./yr over the area of the entire ice cap (1127 km2).

On the errors involved in the estimate of glacier ice volume from ice thickness data

The assessment of the glacier thickness is one of the most widespread applications of radioglaciology, and is the basis for estimating the glacier volume. The accuracy of the measurement of ice thickness, the distribution of profiles over the glacier and the accuracy of the boundary delineation of the glacier are the most important factors determining the error in the evaluation of the glacier volume. The aim of this study is to get an accurate estimate of the error incurred in the estimate of glacier volume from GPR-retrieved ice-thickness data.

Double ion implantation and pulsed laser melting processes for third generation solar cells

In the framework of the third generation of photovoltaic devices, the intermediate band solar cell is one of the possible candidates to reach higher efficiencies with a lower processing cost. In this work, we introduce a novel processing method based on a double ion implantation and, subsequently, a pulsed laser melting (PLM) process to obtain thicker layers of Ti supersaturated Si. We perform ab initio theoretical calculations of Si impurified with Ti showing that Ti in Si is a good candidate to theoretically form an intermediate band material in the Ti supersaturated Si. From time-of-flight secondary ion mass spectroscopy measurements, we confirm that we have obtained a Ti implanted and PLM thicker layer of 135 nm. Transmission electron microscopy reveals a single crystalline structure whilst the electrical characterization confirms the transport properties of an intermediate band material/Si substrate junction. High subbandgap absorption has been measured, obtaining an approximate value of 104 cm−1 in the photons energy range from 1.1 to 0.6 eV.

Stability and dynamics in a hyperthermophilic protein with melting temperature close to 200°C

The rubredoxin protein from the hyperthermophilic archaebacterium Pyrococcus furiosus was examined by a hydrogen exchange method. Even though the protein does not exhibit reversible thermal unfolding, one can determine its stability parameters—free energy, enthalpy, entropy, and melting temperature—and also the distribution of stability throughout the protein, by using hydrogen exchange to measure the reversible cycling of the protein between native and unfolded states that occurs even under native conditions.