Flight dynamics and stability of kites in steady and unsteady wind conditions

The flight dynamics and stability of a kite with a single main line flying in steady and unsteady wind conditions are discussed. A simple dynamic model with five degrees of freedom is derived with the aid of Lagrangian formulation, which explicitly avoids any constraint force in the equations of motion. The longitudinal and lateral–directional modes and stability of the steady flight under constant wind conditions are analyzed by using both numerical and analytical methods. Taking advantage of the appearance of small dimensionless parameters in the model, useful analytical formulas for stable-designed kites are found. Under nonsteady wind-velocity conditions, the equilibrium state disappears and periodic orbits occur. The kite stability and an interesting resonance phenomenon are explored with the aid of a numerical method based on Floquet theory.

Influence of gravity on heavy particle statistics in turbulent channel and pipe flow at matched Kàrmàn number

In this work, we use large eddy simulations (LES) and Lagrangian tracking to study the influence of gravity on particle statistics in a fully developed turbulent upward/downward flow in a vertical channel and pipe at matched Kàrmàn number. Only drag and gravity are considered in the equation of motion for solid particles, which are assumed to have no influence on the flow field. Particle interactions with the wall are fully elastic. Our findings obtained from the particle statistics confirm that: (i) the gravity seems to modify both the quantitative and qualitative behavior of the particle distribution and statistics of the particle velocity in wall normal direction; (ii) however, only the quantitative behavior of velocity particle in streamwise direction and the root mean square of velocity components is modified; (iii) the statistics of fluid and particles coincide very well near the wall in channel and pipe flow with equal Kàrmàn number; (iv) pipe curvature seems to have quantitative and qualitative influence on the particle velocity and on the particle concentration in wall normal direction.

Comparison of linear and non-linear 2D+T registration methods for DE-MRI cardiac perfusion studies

A series of motion compensation algorithms is run on the challenge data including methods that optimize only a linear transformation, or a non-linear transformation, or both – first a linear and then a non-linear transformation. Methods that optimize a linear transformation run an initial segmentation of the area of interest around the left myocardium by means of an independent component analysis (ICA) (ICA-*). Methods that optimize non-linear transformations may run directly on the full images, or after linear registration. Non-linear motion compensation approaches applied include one method that only registers pairs of images in temporal succession (SERIAL), one method that registers all image to one common reference (AllToOne), one method that was designed to exploit quasi-periodicity in free breathing acquired image data and was adapted to also be usable to image data acquired with initial breath-hold (QUASI-P), a method that uses ICA to identify the motion and eliminate it (ICA-SP), and a method that relies on the estimation of a pseudo ground truth (PG) to guide the motion compensation.

Low Work-Function Thermionic Emission and Orbital-Motion-Limited Ion Collection at Bare-Tether Cathodic Contact

Una amarra electrodinámica (electrodynamic tether) opera sobre principios electromagnéticos intercambiando momento con la magnetosfera planetaria e interactuando con su ionosfera. Es un subsistema pasivo fiable para desorbitar etapas de cohetes agotadas y satélites al final de su misión, mitigando el crecimiento de la basura espacial. Una amarra sin aislamiento captura electrones del plasma ambiente a lo largo de su segmento polarizado positivamente, el cual puede alcanzar varios kilómetros de longitud, mientras que emite electrones de vuelta al plasma mediante un contactor de plasma activo de baja impedancia en su extremo catódico, tal como un cátodo hueco (hollow cathode). En ausencia de un contactor catódico activo, la corriente que circula por una amarra desnuda en órbita es nula en ambos extremos de la amarra y se dice que ésta está flotando eléctricamente. Para emisión termoiónica despreciable y captura de corriente en condiciones limitadas por movimiento orbital (orbital-motion-limited, OML), el cociente entre las longitudes de los segmentos anódico y catódico es muy pequeño debido a la disparidad de masas entre iones y electrones. Tal modo de operación resulta en una corriente media y fuerza de Lorentz bajas en la amarra, la cual es poco eficiente como dispositivo para desorbitar. El electride C12A7 : e−, que podría presentar una función de trabajo (work function) tan baja como W = 0.6 eV y un comportamiento estable a temperaturas relativamente altas, ha sido propuesto como recubrimiento para amarras desnudas. La emisión termoiónica a lo largo de un segmento así recubierto y bajo el calentamiento de la operación espacial, puede ser más eficiente que la captura iónica. En el modo más simple de fuerza de frenado, podría eliminar la necesidad de un contactor catódico activo y su correspondientes requisitos de alimentación de gas y subsistema de potencia, lo que resultaría en un sistema real de amarra “sin combustible”. Con este recubrimiento de bajo W, cada segmento elemental del segmento catódico de una amarra desnuda de kilómetros de longitud emitiría corriente como si fuese parte de una sonda cilíndrica, caliente y uniformemente polarizada al potencial local de la amarra. La operación es similar a la de una sonda de Langmuir 2D tanto en los segmentos catódico como anódico. Sin embargo, en presencia de emisión, los electrones emitidos resultan en carga espacial (space charge) negativa, la cual reduce el campo eléctrico que los acelera hacia fuera, o incluso puede desacelerarlos y hacerlos volver a la sonda. Se forma una doble vainas (double sheath) estable con electrones emitidos desde la sonda e iones provenientes del plasma ambiente. La densidad de corriente termoiónica, variando a lo largo del segmento catódico, podría seguir dos leyes distintas bajo diferentes condiciones: (i) la ley de corriente limitada por la carga espacial (space-charge-limited, SCL) o (ii) la ley de Richardson-Dushman (RDS). Se presenta un estudio preliminar sobre la corriente SCL frente a una sonda emisora usando la teoría de vainas (sheath) formada por la captura iónica en condiciones OML, y la corriente electrónica SCL entre los electrodos cilíndricos según Langmuir. El modelo, que incluye efectos óhmicos y el efecto de transición de emisión SCL a emisión RDS, proporciona los perfiles de corriente y potencial a lo largo de la longitud completa de la amarra. El análisis muestra que en el modo más simple de fuerza de frenado, bajo condiciones orbitales y de amarras típicas, la emisión termoiónica proporciona un contacto catódico eficiente y resulta en una sección catódica pequeña. En el análisis anterior, tanto la transición de emisión SCL a RD como la propia ley de emisión SCL consiste en un modelo muy simplificado. Por ello, a continuación se ha estudiado con detalle la solución de vaina estacionaria de una sonda con emisión termoiónica polarizada negativamente respecto a un plasma isotrópico, no colisional y sin campo magnético. La existencia de posibles partículas atrapadas ha sido ignorada y el estudio incluye tanto un estudio semi-analítico mediante técnica asintóticas como soluciones numéricas completas del problema. Bajo las tres condiciones (i) alto potencial, (ii) R = Rmax para la validez de la captura iónica OML, y (iii) potencial monotónico, se desarrolla un análisis asintótico auto-consistente para la estructura de plasma compleja que contiene las tres especies de cargas (electrones e iones del plasma, electrones emitidos), y cuatro regiones espaciales distintas, utilizando teorías de movimiento orbital y modelos cinéticos de las especies. Aunque los electrones emitidos presentan carga espacial despreciable muy lejos de la sonda, su efecto no se puede despreciar en el análisis global de la estructura de la vaina y de dos capas finas entre la vaina y la región cuasi-neutra. El análisis proporciona las condiciones paramétricas para que la corriente sea SCL. También muestra que la emisión termoiónica aumenta el radio máximo de la sonda para operar dentro del régimen OML y que la emisión de electrones es mucho más eficiente que la captura iónica para el segmento catódico de la amarra. En el código numérico, los movimientos orbitales de las tres especies son modelados para potenciales tanto monotónico como no-monotónico, y sonda de radio R arbitrario (dentro o más allá del régimen de OML para la captura iónica). Aprovechando la existencia de dos invariante, el sistema de ecuaciones Poisson-Vlasov se escribe como una ecuación integro-diferencial, la cual se discretiza mediante un método de diferencias finitas. El sistema de ecuaciones algebraicas no lineal resultante se ha resuelto de con un método Newton-Raphson paralelizado. Los resultados, comparados satisfactoriamente con el análisis analítico, proporcionan la emisión de corriente y la estructura del plasma y del potencial electrostático. ABSTRACT An electrodynamic tether operates on electromagnetic principles and exchanges momentum through the planetary magnetosphere, by continuously interacting with the ionosphere. It is a reliable passive subsystem to deorbit spent rocket stages and satellites at its end of mission, mitigating the growth of orbital debris. A tether left bare of insulation collects electrons by its own uninsulated and positively biased segment with kilometer range, while electrons are emitted by a low-impedance active device at the cathodic end, such as a hollow cathode, to emit the full electron current. In the absence of an active cathodic device, the current flowing along an orbiting bare tether vanishes at both ends and the tether is said to be electrically floating. For negligible thermionic emission and orbital-motion-limited (OML) collection throughout the entire tether (electron/ion collection at anodic/cathodic segment, respectively), the anodic-to-cathodic length ratio is very small due to ions being much heavier, which results in low average current and Lorentz drag. The electride C12A7 : e−, which might present a possible work function as low as W = 0.6 eV and moderately high temperature stability, has been proposed as coating for floating bare tethers. Thermionic emission along a thus coated cathodic segment, under heating in space operation, can be more efficient than ion collection and, in the simplest drag mode, may eliminate the need for an active cathodic device and its corresponding gas-feed requirements and power subsystem, which would result in a truly “propellant-less” tether system. With this low-W coating, each elemental segment on the cathodic segment of a kilometers-long floating bare-tether would emit current as if it were part of a hot cylindrical probe uniformly polarized at the local tether bias, under 2D probe conditions that are also applied to the anodic-segment analysis. In the presence of emission, emitted electrons result in negative space charge, which decreases the electric field that accelerates them outwards, or even reverses it, decelerating electrons near the emitting probe. A double sheath would be established with electrons being emitted from the probe and ions coming from the ambient plasma. The thermionic current density, varying along the cathodic segment, might follow two distinct laws under different con ditions: i) space-charge-limited (SCL) emission or ii) full Richardson-Dushman (RDS) emission. A preliminary study on the SCL current in front of an emissive probe is presented using the orbital-motion-limited (OML) ion-collection sheath and Langmuir’s SCL electron current between cylindrical electrodes. A detailed calculation of current and bias profiles along the entire tether length is carried out with ohmic effects considered and the transition from SCL to full RDS emission is included. Analysis shows that in the simplest drag mode, under typical orbital and tether conditions, thermionic emission provides efficient cathodic contact and leads to a short cathodic section. In the previous analysis, both the transition between SCL and RDS emission and the current law for SCL condition have used a very simple model. To continue, considering an isotropic, unmagnetized, colissionless plasma and a stationary sheath, the probe-plasma contact is studied in detail for a negatively biased probe with thermionic emission. The possible trapped particles are ignored and this study includes both semianalytical solutions using asymptotic analysis and complete numerical solutions. Under conditions of i) high bias, ii) R = Rmax for ion OML collection validity, and iii) monotonic potential, a self-consistent asymptotic analysis is carried out for the complex plasma structure involving all three charge species (plasma electrons and ions, and emitted electrons) and four distinct spatial regions using orbital motion theories and kinetic modeling of the species. Although emitted electrons present negligible space charge far away from the probe, their effect cannot be neglected in the global analysis for the sheath structure and two thin layers in between the sheath and the quasineutral region. The parametric conditions for the current to be space-chargelimited are obtained. It is found that thermionic emission increases the range of probe radius for OML validity and is greatly more effective than ion collection for cathodic contact of tethers. In the numerical code, the orbital motions of all three species are modeled for both monotonic and non-monotonic potential, and for any probe radius R (within or beyond OML regime for ion collection). Taking advantage of two constants of motion (energy and angular momentum), the Poisson-Vlasov equation is described by an integro differential equation, which is discretized using finite difference method. The non-linear algebraic equations are solved using a parallel implementation of the Newton-Raphson method. The results, which show good agreement with the analytical results, provide the results for thermionic current, the sheath structure, and the electrostatic potential.

Limit load instabilities in structural elements

Este trabajo analiza distintas inestabilidades en estructuras formadas por distintos materiales. En particular, se capturan y se modelan las inestabilidades usando el método de Riks. Inicialmente, se analiza la bifurcación en depósitos cilíndricos formados por material anisótropo sometidos a carga axial y presión interna. El análisis de bifurcación y post-bifurcación asociados con cilindros de pared gruesa se formula para un material incompresible reforzado con dos fibras que son mecánicamente equivalentes y están dispuestas simétricamente. Consideramos dos casos en la naturaleza de la anisotropía: (i) Fibras refuerzo que tienen una influencia particular sobre la respuesta a cortante del material y (ii) Fibras refuerzo que influyen sólo si la fibra cambia de longitud con la deformación. Se analiza la propagación de las inestabilidades. En concreto, se diferencia en el abultamiento (bulging) entre la propagación axial y la propagación radial de la inestabilidad. Distintos modelos sufren una u otra propagación. Por último, distintas inestabilidades asociadas al mecanismo de ablandamiento del material (material softening) en contraposición al de endurecimiento (hardening) en una estructura (viga) de a: hormigón y b: hormigón reforzado son modeladas utilizando una metodología paralela a la desarrollada en el análisis de inestabilidades en tubos sometidos a presión interna. This present work deals with the instability of structures made of various materials. It captures and models different types of instabilities using numerical analysis. Firstly, we consider bifurcation for anisotropic cylindrical shells subject to axial loading and internal pressure. Analysis of bifurcation and post bifurcation of inflated hyperelastic thick-walled cylinder is formulated using a numerical procedure based on the modified Riks method for an incompressible material with two preferred directions which are mechanically equivalent and are symmetrically disposed. Secondly, bulging/necking motion in doubly fiber-reinforced incompressible nonlinearly elastic cylindrical shells is captured and we consider two cases for the nature of the anisotropy: (i) reinforcing models that have a particular influence on the shear response of the material and (ii) reinforcing models that depend only on the stretch in the fiber direction. The different instability motions are considered. Axial propagation of the bulging instability mode in thin-walled cylinders under inflation is analyzed. We present the analytical solution for this particular motion as well as for radial expansion during bulging evolution. For illustration, cylinders that are made of either isotropic incompressible non-linearly elastic materials or doubly fiber reinforced incompressible non-linearly elastic materials are considered. Finally, strain-softening constitutive models are considered to analyze two concrete structures: a reinforced concrete beam and an unreinforced notch beam. The bifurcation point is captured using the Riks method used previously to analyze bifurcation of a pressurized cylinder.

Nonlinear seismic behaviour of concrete arch bridges

Arch bridge structural solution has been known for centuries, in fact the simple nature of arch that require low tension and shear strength was an advantage as the simple materials like stone and brick were the only option back in ancient centuries. By the pass of time especially after industrial revolution, the new materials were adopted in construction of arch bridges to reach longer spans. Nowadays one long span arch bridge is made of steel, concrete or combination of these two as "CFST", as the result of using these high strength materials, very long spans can be achieved. The current record for longest arch belongs to Chaotianmen bridge over Yangtze river in China with 552 meters span made of steel and the longest reinforced concrete type is Wanxian bridge which also cross the Yangtze river through a 420 meters span. Today the designer is no longer limited by span length as long as arch bridge is the most applicable solution among other approaches, i.e. cable stayed and suspended bridges are more reasonable if very long span is desired. Like any super structure, the economical and architectural aspects in construction of a bridge is extremely important, in other words, as a narrower bridge has better appearance, it also require smaller volume of material which make the design more economical. Design of such bridge, beside the high strength materials, requires precise structural analysis approaches capable of integrating the combination of material behaviour and complex geometry of structure and various types of loads which may be applied to bridge during its service life. Depend on the design strategy, analysis may only evaluates the linear elastic behaviour of structure or consider the nonlinear properties as well. Although most of structures in the past were designed to act in their elastic range, the rapid increase in computational capacity allow us to consider different sources of nonlinearities in order to achieve a more realistic evaluations where the dynamic behaviour of bridge is important especially in seismic zones where large movements may occur or structure experience P - _ effect during the earthquake. The above mentioned type of analysis is computationally expensive and very time consuming. In recent years, several methods were proposed in order to resolve this problem. Discussion of recent developments on these methods and their application on long span concrete arch bridges is the main goal of this research. Accordingly available long span concrete arch bridges have been studied to gather the critical information about their geometrical aspects and properties of their materials. Based on concluded information, several concrete arch bridges were designed for further studies. The main span of these bridges range from 100 to 400 meters. The Structural analysis methods implemented in in this study are as following: Elastic Analysis: Direct Response History Analysis (DRHA): This method solves the direct equation of motion over time history of applied acceleration or imposed load in linear elastic range. Modal Response History Analysis (MRHA): Similar to DRHA, this method is also based on time history, but the equation of motion is simplified to single degree of freedom system and calculates the response of each mode independently. Performing this analysis require less time than DRHA. Modal Response Spectrum Analysis (MRSA): As it is obvious from its name, this method calculates the peak response of structure for each mode and combine them using modal combination rules based on the introduced spectra of ground motion. This method is expected to be fastest among Elastic analysis. Inelastic Analysis: Nonlinear Response History Analysis (NL-RHA): The most accurate strategy to address significant nonlinearities in structural dynamics is undoubtedly the nonlinear response history analysis which is similar to DRHA but extended to inelastic range by updating the stiffness matrix for every iteration. This onerous task, clearly increase the computational cost especially for unsymmetrical buildings that requires to be analyzed in a full 3D model for taking the torsional effects in to consideration. Modal Pushover Analysis (MPA): The Modal Pushover Analysis is basically the MRHA but extended to inelastic stage. After all, the MRHA cannot solve the system of dynamics because the resisting force fs(u; u_ ) is unknown for inelastic stage. The solution of MPA for this obstacle is using the previously recorded fs to evaluate system of dynamics. Extended Modal Pushover Analysis (EMPA): Expanded Modal pushover is a one of very recent proposed methods which evaluates response of structure under multi-directional excitation using the modal pushover analysis strategy. In one specific mode,the original pushover neglect the contribution of the directions different than characteristic one, this is reasonable in regular symmetric building but a structure with complex shape like long span arch bridges may go through strong modal coupling. This method intend to consider modal coupling while it take same time of computation as MPA. Coupled Nonlinear Static Pushover Analysis (CNSP): The EMPA includes the contribution of non-characteristic direction to the formal MPA procedure. However the static pushovers in EMPA are performed individually for every mode, accordingly the resulted values from different modes can be combined but this is only valid in elastic phase; as soon as any element in structure starts yielding the neutral axis of that section is no longer fixed for both response during the earthquake, meaning the longitudinal deflection unavoidably affect the transverse one or vice versa. To overcome this drawback, the CNSP suggests executing pushover analysis for governing modes of each direction at the same time. This strategy is estimated to be more accurate than MPA and EMPA, moreover the calculation time is reduced because only one pushover analysis is required. Regardless of the strategy, the accuracy of structural analysis is highly dependent on modelling and numerical integration approaches used in evaluation of each method. Therefore the widely used Finite Element Method is implemented in process of all analysis performed in this research. In order to address the study, chapter 2, starts with gathered information about constructed long span arch bridges, this chapter continuous with geometrical and material definition of new models. Chapter 3 provides the detailed information about structural analysis strategies; furthermore the step by step description of procedure of all methods is available in Appendix A. The document ends with the description of results and conclusion of chapter 4.

Proactive and reactive thermal aware optimization techniques to minimize the environmental impact of data centers

Los Centros de Datos se encuentran actualmente en cualquier sector de la economía mundial. Están compuestos por miles de servidores, dando servicio a los usuarios de forma global, las 24 horas del día y los 365 días del año. Durante los últimos años, las aplicaciones del ámbito de la e-Ciencia, como la e-Salud o las Ciudades Inteligentes han experimentado un desarrollo muy significativo. La necesidad de manejar de forma eficiente las necesidades de cómputo de aplicaciones de nueva generación, junto con la creciente demanda de recursos en aplicaciones tradicionales, han facilitado el rápido crecimiento y la proliferación de los Centros de Datos. El principal inconveniente de este aumento de capacidad ha sido el rápido y dramático incremento del consumo energético de estas infraestructuras. En 2010, la factura eléctrica de los Centros de Datos representaba el 1.3% del consumo eléctrico mundial. Sólo en el año 2012, el consumo de potencia de los Centros de Datos creció un 63%, alcanzando los 38GW. En 2013 se estimó un crecimiento de otro 17%, hasta llegar a los 43GW. Además, los Centros de Datos son responsables de más del 2% del total de emisiones de dióxido de carbono a la atmósfera. Esta tesis doctoral se enfrenta al problema energético proponiendo técnicas proactivas y reactivas conscientes de la temperatura y de la energía, que contribuyen a tener Centros de Datos más eficientes. Este trabajo desarrolla modelos de energía y utiliza el conocimiento sobre la demanda energética de la carga de trabajo a ejecutar y de los recursos de computación y refrigeración del Centro de Datos para optimizar el consumo. Además, los Centros de Datos son considerados como un elemento crucial dentro del marco de la aplicación ejecutada, optimizando no sólo el consumo del Centro de Datos sino el consumo energético global de la aplicación. Los principales componentes del consumo en los Centros de Datos son la potencia de computación utilizada por los equipos de IT, y la refrigeración necesaria para mantener los servidores dentro de un rango de temperatura de trabajo que asegure su correcto funcionamiento. Debido a la relación cúbica entre la velocidad de los ventiladores y el consumo de los mismos, las soluciones basadas en el sobre-aprovisionamiento de aire frío al servidor generalmente tienen como resultado ineficiencias energéticas. Por otro lado, temperaturas más elevadas en el procesador llevan a un consumo de fugas mayor, debido a la relación exponencial del consumo de fugas con la temperatura. Además, las características de la carga de trabajo y las políticas de asignación de recursos tienen un impacto importante en los balances entre corriente de fugas y consumo de refrigeración. La primera gran contribución de este trabajo es el desarrollo de modelos de potencia y temperatura que permiten describes estos balances entre corriente de fugas y refrigeración; así como la propuesta de estrategias para minimizar el consumo del servidor por medio de la asignación conjunta de refrigeración y carga desde una perspectiva multivariable. Cuando escalamos a nivel del Centro de Datos, observamos un comportamiento similar en términos del balance entre corrientes de fugas y refrigeración. Conforme aumenta la temperatura de la sala, mejora la eficiencia de la refrigeración. Sin embargo, este incremente de la temperatura de sala provoca un aumento en la temperatura de la CPU y, por tanto, también del consumo de fugas. Además, la dinámica de la sala tiene un comportamiento muy desigual, no equilibrado, debido a la asignación de carga y a la heterogeneidad en el equipamiento de IT. La segunda contribución de esta tesis es la propuesta de técnicas de asigación conscientes de la temperatura y heterogeneidad que permiten optimizar conjuntamente la asignación de tareas y refrigeración a los servidores. Estas estrategias necesitan estar respaldadas por modelos flexibles, que puedan trabajar en tiempo real, para describir el sistema desde un nivel de abstracción alto. Dentro del ámbito de las aplicaciones de nueva generación, las decisiones tomadas en el nivel de aplicación pueden tener un impacto dramático en el consumo energético de niveles de abstracción menores, como por ejemplo, en el Centro de Datos. Es importante considerar las relaciones entre todos los agentes computacionales implicados en el problema, de forma que puedan cooperar para conseguir el objetivo común de reducir el coste energético global del sistema. La tercera contribución de esta tesis es el desarrollo de optimizaciones energéticas para la aplicación global por medio de la evaluación de los costes de ejecutar parte del procesado necesario en otros niveles de abstracción, que van desde los nodos hasta el Centro de Datos, por medio de técnicas de balanceo de carga. Como resumen, el trabajo presentado en esta tesis lleva a cabo contribuciones en el modelado y optimización consciente del consumo por fugas y la refrigeración de servidores; el modelado de los Centros de Datos y el desarrollo de políticas de asignación conscientes de la heterogeneidad; y desarrolla mecanismos para la optimización energética de aplicaciones de nueva generación desde varios niveles de abstracción. ABSTRACT Data centers are easily found in every sector of the worldwide economy. They consist of tens of thousands of servers, serving millions of users globally and 24-7. In the last years, e-Science applications such e-Health or Smart Cities have experienced a significant development. The need to deal efficiently with the computational needs of next-generation applications together with the increasing demand for higher resources in traditional applications has facilitated the rapid proliferation and growing of data centers. A drawback to this capacity growth has been the rapid increase of the energy consumption of these facilities. In 2010, data center electricity represented 1.3% of all the electricity use in the world. In year 2012 alone, global data center power demand grew 63% to 38GW. A further rise of 17% to 43GW was estimated in 2013. Moreover, data centers are responsible for more than 2% of total carbon dioxide emissions. This PhD Thesis addresses the energy challenge by proposing proactive and reactive thermal and energy-aware optimization techniques that contribute to place data centers on a more scalable curve. This work develops energy models and uses the knowledge about the energy demand of the workload to be executed and the computational and cooling resources available at data center to optimize energy consumption. Moreover, data centers are considered as a crucial element within their application framework, optimizing not only the energy consumption of the facility, but the global energy consumption of the application. The main contributors to the energy consumption in a data center are the computing power drawn by IT equipment and the cooling power needed to keep the servers within a certain temperature range that ensures safe operation. Because of the cubic relation of fan power with fan speed, solutions based on over-provisioning cold air into the server usually lead to inefficiencies. On the other hand, higher chip temperatures lead to higher leakage power because of the exponential dependence of leakage on temperature. Moreover, workload characteristics as well as allocation policies also have an important impact on the leakage-cooling tradeoffs. The first key contribution of this work is the development of power and temperature models that accurately describe the leakage-cooling tradeoffs at the server level, and the proposal of strategies to minimize server energy via joint cooling and workload management from a multivariate perspective. When scaling to the data center level, a similar behavior in terms of leakage-temperature tradeoffs can be observed. As room temperature raises, the efficiency of data room cooling units improves. However, as we increase room temperature, CPU temperature raises and so does leakage power. Moreover, the thermal dynamics of a data room exhibit unbalanced patterns due to both the workload allocation and the heterogeneity of computing equipment. The second main contribution is the proposal of thermal- and heterogeneity-aware workload management techniques that jointly optimize the allocation of computation and cooling to servers. These strategies need to be backed up by flexible room level models, able to work on runtime, that describe the system from a high level perspective. Within the framework of next-generation applications, decisions taken at this scope can have a dramatical impact on the energy consumption of lower abstraction levels, i.e. the data center facility. It is important to consider the relationships between all the computational agents involved in the problem, so that they can cooperate to achieve the common goal of reducing energy in the overall system. The third main contribution is the energy optimization of the overall application by evaluating the energy costs of performing part of the processing in any of the different abstraction layers, from the node to the data center, via workload management and off-loading techniques. In summary, the work presented in this PhD Thesis, makes contributions on leakage and cooling aware server modeling and optimization, data center thermal modeling and heterogeneityaware data center resource allocation, and develops mechanisms for the energy optimization for next-generation applications from a multi-layer perspective.

Business, development and inclusive supply chains. Exploring pathways for the sustainable incorporation of the poor as suppliers in agrifood supply chains

El panorama global está cambiando, y esto influye sobre la forma en la que entendemos y tratamos de alcanzar un desarrollo humano sostenible. El crecimiento de la población conlleva una mayor presión sobre los recursos, pero también supone una mayor cantidad de mano de obra y de talento; la concentración en áreas urbanas está cambiando las dinámicas sociales y desafiando los canales de comercialización tradicionales, pero también genera nuevos mercados y fomenta la innovación; los cambios en la economía global están reduciendo los tradicionales desequilibrios de poder entre los países occidentales y el resto del mundo; y las crecientes interconexiones crean nuevos riesgos pero también oportunidades para lanzar iniciativas de alcance global. Todas estas tendencias nos están obligando a repensar qué es el desarrollo humano y de qué manera deberíamos afrontar el reto de la pobreza. Es comúnmente aceptado que la globalización implica interdependencia y que, para conseguir un desarrollo humano sostenible, la colaboración entre actores de distintos ámbitos es necesaria. Se observa una creciente convergencia de temas, intereses y soluciones en torno al desarrollo sostenible, incluso en diferentes países y sectores, lo que está facilitando la colaboración estratégica entre empresas, gobiernos y sociedad civil. Existen pocas duda a día de hoy sobre el papel fundamental que las empresas deben desempeñar en la transición mundial hacia la sostenibilidad ambiental y la erradicación de la pobreza. Las empresas están evolucionando desde un enfoque tradicional centrado en la maximización de beneficios económicos hacia un enfoque holístico que integra la sostenibilidad y la responsabilidad social como parte del núcleo de negocio de las compañías. En el ámbito medioambiental, muchas empresas ya han comenzado a actuar y tratan de reducir sus emisiones, sus desechos y su consumo de energía. Sin embargo la contribución de las empresas a la reducción de la pobreza no está tan clara. Actualmente en torno a 1,2 miles de millones de personas viven en situación de extrema pobreza. La mayoría de estas personas aún vive en zonas rurales donde la mayor parte de la población activa trabaja en el sector agrícola. Por lo tanto, mejorar las oportunidades y reducir los riesgos de los productores más vulnerables en el sector de la agricultura puede ser un motor de desarrollo rural y reducción de la pobreza, especialmente en países de bajo nivel de desarrollo cuyas economías están fundamentalmente basadas en la agricultura. Algunas empresas comienzan a incluir a los pobres en sus operaciones como consumidores, proveedores y emprendedores. Esta tesis se centra en las potenciales oportunidades relacionadas con la incorporación sostenible de los pobres como proveedores de productos y/o de mano de obra. La colaboración entre empresas y productores vulnerables de países en desarrollo es un tema relativamente nuevo y todavía poco estudiado. La pregunta que guía esta tesis es: “¿Cómo pueden las empresas facilitar la inclusión sostenible en cadenas de suministro de productores vulnerables de los países menos desarrollados?”. Para responder a la pregunta anterior, la autora ha aplicado una metodología de casos de estudio. Esta metodología se considera apropiada porque la investigación sobre cadenas de suministro inclusivas es todavía escasa y porque es necesario entender en profundidad un fenómeno de la vida real, y para ello es fundamental conocer su contexto. En primer lugar, se realiza una revisión de literatura para identificar las proposiciones y los constructos teóricos que guiarán la posterior recogida de datos. La revisión de literatura se divide en dos partes: una más general que explora la dimensión social de la sostenibilidad en cadenas de suministro, y una más específica que se centra en la incorporación de los pobres como proveedores en cadenas de suministro. A lo largo de la última década, ha habido un crecimiento exponencial de los estudios académicos sobre la sostenibilidad de las cadenas de suministro, pero la mayoría de los esfuerzos se han dirigido hacia la dimensión medioambiental de la sostenibilidad. Por lo tanto la revisión de literatura, que se presenta en la Sección 3.1 (página 35) y que profundiza en la sostenibilidad social de las cadenas de suministro, puede considerarse una contribución en sí misma. Esta revisión de literatura revela que la investigación sobre aspectos sociales en cadenas de suministro está cobrando impulso en distintas áreas de conocimiento, principalmente en los ámbitos de investigación sobre “gestión de cadenas de suministro”, “responsabilidad social corporativa” y “estudios del desarrollo”. La investigación existente sobre sostenibilidad social de cadenas de suministro se centra en tres temas: aclarar la definición de sostenibilidad social; analizar la implementación de estrategias de sostenibilidad social en cadenas de suministro; y estudiar el apoyo de las em presas líderes a proveedores vulnerables para facilitar su transición hacia la sostenibilidad. Un marco conceptual que resume los principales hallazgos de esta primera parte de la revisión de literatura es planteado en la Figura 7 (página 48). No obstante, en el área de investigación que está emergiendo en torno a la sostenibilidad social de las cadenas de suministro, los estudios relacionados con la reducción de la pobreza son aún escasos. Además se aprecia una falta de contribuciones desde y sobre los países menos desarrollados, así como una clara tendencia a reflejar la visión de las empresas líderes de las cadenas de suministro, olvidando la perspectiva de los proveedores. La segunda parte de la revisión de literatura presentada en la Sección 3.2 (página 51) profundiza en tres líneas de investigación que exploran, desde distintas perspectivas, la inclusión de los pobres en cadenas de suministro. Estas líneas son “Global Value Chains” (GVC), “Base of the Pyramid” (BoP) y “Sustainable Supply Chain Management” (SSCM). La investigación en GVC analiza las cadenas de suministro desde la perspectiva de la globalización económica y el comercio internacional, poniendo especial énfasis en las implicaciones para los países en desarrollo y las comunidades vulnerables. GVC caracteriza las cadenas de suministro según la forma en la que son gobernadas, las oportunidades de mejora que existen para los productores que forman parte de la cadena y el grado de inclusión o exclusión de las comunidades más pobres y vulnerables. La investigación en BoP explora las relaciones comerciales entre empresas y comunidades pobres. La premisa fundamental del concepto BoP es la posibilidad de combinar la generación de beneficios con la reducción de la pobreza. La propuesta original es que mediante la venta de productos y servicios a las comunidades pobres de países en desarrollo, la pobreza puede ser reducida al tiempo que las empresas incrementan sus beneficios, especialmente las grandes empresas multinacionales. Esta idea ha ido evolucionando y, a día de hoy, los investigadores BoP consideran la incorporación de los pobres no sólo como consumidores sino también como empleados, proveedores y co-creadores. La investigación en SSCM ha estado fundamentalmente orientada al estudio de la dimensión medioambiental de la sostenibilidad de cadenas de suministro. Sin embargo, la creciente externalización de la producción a países en desarrollo y las demandas de los grupos de interés para que las empresas aborden todos los aspectos de la sostenibilidad han llevado a los académicos de SSCM a reconocer la importancia de integrar asuntos relacionados con la reducción de la pobreza en sus investigaciones. Algunos estudios comienzan a apuntar los principales retos a los que se enfrentan las empresas para colaborar con productores vulnerables en sus cadenas de suministro. Estos retos son: falta de comunicación, altos costes de transacción y el incremento de la complejidad de las operaciones. Las contribuciones de estas tres líneas de investigación son complementarias para el estudio de las cadenas de suministro inclusivas. Sin embargo, raramente han sido consideradas conjuntamente, ya que pertenecen a ámbitos de conocimiento distintos. Esta tesis integra las aportaciones de GVC, BoP y SSCM en un marco conceptual para la creación y gestión de cadenas de suministro inclusivas. Este marco conceptual para cadenas de suministro inclusivas queda representado en la Figura 9 (página 68). El marco conceptual refleja las motivaciones que llevan a las empresas a colaborar con productores vulnerables, los retos a los que se enfrentan al hacerlo, y los caminos o estrategias que están siguiendo para construir y operar cadenas de suministro inclusivas de manera que sean beneficiosas tanto para la empresa como para los productores vulnerables. A fin de validar y refinar el marco conceptual propuesto, tres casos de estudio se llevan a cabo. Las cadenas de suministro analizadas por los casos de estudio pertenecen al sector agrícola y sus principales proveedores se encuentran en países de África subsahariana. Múltiples métodos de recolección de datos y triangulación son utilizados para mejorar la fiabilidad de los datos. La autora desarrolló trabajos de campo en Senegal, Etiopía y Tanzania. Estos viajes permitieron enriquecer el proceso de recogida de información mediante entrevistas semiestructuradas y conversaciones informales con los principales actores de la cadena de suministro y mediante la observación directa de los procesos y las interacciones entre productores vulnerables y empresas. El Caso de estudio A (Sección 5.1 en página 96) es un caso de estudio único. Analiza la cadena de suministro local de verduras en Senegal. La organización focal es Manobi, una empresa senegalesa que provee servicios de bajo coste a emprendedores locales del sector agrícola. El Caso de estudio A proporciona un interesante análisis del funcionamiento de una cadena de suministro local en un país en desarrollo y muestra como la provisión de servicios profesionales puede mejorar el desempeño de productores vulnerables. El Caso de estudio B (Sección 5.2 en página 122) es un caso de estudio único. Analiza la cadena de suministro global de flor cortada con origen en Etiopía. La organización focal es EHPEA, la Asociación Etíope de Productores y Exportadores Hortícolas, cuya misión es promover y salvaguardar la posición competitiva del sector agrícola etíope en el mercado global. El Caso de estudio B ayuda a comprender mejor la perspectiva de los proveedores respecto a los requerimiento de sostenibilidad del mercado global. También muestra cómo la inclusión de los productores en el proceso de desarrollo de un estándar privado facilita su implementación posterior. El Caso de estudio C (Sección 5.3 en página 143) es un caso de estudio múltiple. Analiza la cadena de suministro global de café especial con origen en Tanzania. Las organizaciones focales son comerciantes que conectan de manera directa a pequeños agricultores de café en países en desarrollo con empresas tostadoras de café en países desarrollados. El Caso de estudio C muestra cómo un pequeño agricultor puede proveer un producto “premium” al mercado global, y participar en un segmento diferenciado del mercado a través de una cadena de suministro transparente y eficiente. Las aportaciones empíricas de los casos de estudio ayudan a validar y mejorar el marco conceptual sobre cadenas de suministro inclusivas (ver discusión en el Capítulo 6 en página 170). El resultado es la propuesta de una nueva versión del marco conceptual representado en la Figura 40 (página 195). Los casos de estudio también proporcionan interesantes aportaciones en relación a la gestión de cadenas de suministro inclusivas y muestran las perspectivas de distintos actores implicados. Esta tesis arroja luz sobre el papel de las empresas en la creación y la gestión de cadenas de suministro inclusivas llevando a cabo una revisión de literatura multidisciplinar y analizando tres casos de estudio en países africanos. Como resultado, esta tesis presenta una serie de contribuciones empíricas y teóricas al ámbito de investigación emergente en torno a las cadenas de suministro inclusivas (Capítulo 7). Esta tesis también pretende ser útil a profesionales que deseen facilitar la incorporación de los pobres como proveedores en condiciones justas y beneficiosas. ABSTRACT The global outlook is changing, and this is influencing the way we understand and try to achieve sustainable human development. Population growth entails increasing pressure over resources, but it also provides greater workforce and talent; concentration in urban areas is changing social dynamics and challenging traditional marketing channels, but also creating news markets and driving innovation; the global economy shift is rebalancing the traditional power imbalance between Western countries and the rest of the world, making new opportunities to arise; and interconnections and global interdependence create new risks but also opportunities for launching initiatives with a global reach. All these trends are impelling us to rethink what development is and in which way poverty alleviation should be approached. It is generally agreed that globalization implies interdependence and, in order to achieve sustainable human development, collaboration of all actors is needed. A convergence of issues, interests and solutions related to sustainable development is being observed across countries and sectors, encouraging strategic collaboration among companies, governments and civil society. There is little doubt nowadays about the crucial role of the private sector in the world’s path towards environmental sustainability and poverty alleviation. Businesses are evolving from a “business as usual” stance to a more sustainable and responsible approach. In the environmental arena, many companies have already “walk the talk”, implementing environmental management systems and trying to reduce emissions and energy consumption. However, regarding poverty alleviation, their contribution is less clear. There are around 1.2 billion people living in extreme poverty. Most of this people still live in rural areas where the agricultural sector employs a big part of the active population. Therefore, improving opportunities and reducing risks for vulnerable producers in the agri-food sector can be a primary engine of rural development and poverty alleviation, particularly in the poor, agriculture-based economies of least developed countries. Some companies are beginning to include the poor into their operations as consumers, suppliers and entrepreneurs. This thesis focuses specifically on the potential opportunities related to the sustainable incorporation of the poor as suppliers of products and/or labor. Business collaboration with vulnerable producers in developing countries is a relatively new trend and it is still understudied. The overall question guiding this thesis is: “How can businesses facilitate the sustainable inclusion of vulnerable producers from least developed countries into supply chains?”. In order to answer the research question, the author has applied a case study research strategy. This methodology is considered appropriate because research about inclusive supply chains is still at an early stage, and because there is a need to understand a real-life phenomenon in depth, but such understanding encompasses important contextual conditions. First, a literature review is conducted, in order to identify the research propositions and theoretical constructs that will guide the data collection. The literature review is divided in two parts: a more general one that explores the social dimension of sustainability of supply chains, and a more specific one that focuses on the incorporation of the poor as suppliers in supply chains. During the last decade, there has been an exponential growth of studies in the field of supply chain sustainability, but research efforts have traditionally been directed towards the analysis of the environmental dimension. Therefore, the literature review presented in Section 3.1 (page 35) that delves into social sustainability of supply chains can be considered a contribution in itself. This literature review reveals that the investigation of social issues in supply chains is gaining momentum and comes from different academic disciplines, namely Supply Chain Management, Corporate Social Responsibility and Development Studies. Existing research about social sustainability of supply chains focuses on three issues: clarify the definition of social sustainability; analyze the implementation of social sustainability strategies in supply chains; and study lead companies’ support to vulnerable suppliers in their transition towards sustainability. A conceptual framework that outlines the main findings that emerge from this first part of literature review is proposed in Figure 7 (page 48). Nevertheless, in this nascent field of social sustainability of supply chains, studies related to poverty alleviation are still scarce. Moreover, a lack of contributions from and about least developed countries has been observed, as well as a tendency to reflect on the lead firms’ standpoint, neglecting the suppliers’ perspective. The second part of the literature review (Section 3.2 in page 51) delves into three research streams that are exploring the inclusion of the poor into supply chains from different viewpoints. These research streams are Global Value Chains (GVC), Base of the Pyramid (BoP) and Sustainable Supply Chain Management (SSCM). GVC research discusses the dynamics of economic globalization and international trade, putting special emphasis in the implications for developing countries and vulnerable communities. GVC characterizes supply chains by the way they are governed, the upgrading opportunities that exist for producers in the chain and the degree of inclusion or exclusion of impoverished communities. BoP research explores trading relationships between businesses and impoverished communities. The core premise of the BoP concept is the possibility to combine profits with poverty alleviation. The original BoP proposition is that by marketing innovative products and services to poor communities in developing countries, poverty would be reduced and companies would increase their benefits, especially multinational companies. This idea has evolved to consider the incorporation of the poor to business activities not only as consumers, but also as employees, entrepreneurs and co-creators. The SSCM school of thought has mainly focused on studying the environmental dimension of supply chain sustainability, neglecting the consideration of the social perspective. However, in recent years, increasing outsourcing of production to developing countries and stakeholders’ demands for a more holistic approach to business sustainability have led SSCM scholars to acknowledge the importance of integrating poverty concerns in this field’s research agenda. Some SSCM studies identify the main operational challenges for companies which engage with vulnerable suppliers in their supply chains: missing communication, higher transactional and operational costs and increased complexity. Contributions from these three research streams are complementary for the study of inclusive supply chains. However, they have been rarely considered together, since they belong to different research areas. This thesis seeks to play a dovetailing role in this scenario by proposing a conceptual framework for creating and operating inclusive supply chains that builds on contributions from GVC, SSCM and BoP research. This framework for inclusive supply chains is depicted in Figure 9 (page 68), and explains the motivations that drive businesses to collaborate with vulnerable suppliers, the chal lenges they face in doing so, and the pathways they are following in order to build and operate inclusive supply chains profitably for both buying companies and vulnerable suppliers. In order to validate and refine the proposed framework, three case studies are carried out. The supply chains analyzed by the case studies belong to the agri-food sector and source from Sub-Saharan African countries. Multiple data collection methods and triangulation are used in order to improve reliability of findings. The author carried out field work in Senegal, Ethiopia and Tanzania. These travels enriched the data collection process, providing semi-structured interviews and informal conversations with the main actors in the supply chains, as well as direct observation of processes and interactions among companies and vulnerable suppliers. Case study A (Section 5.1 in page 96) is a single case study. It analyzes a local supply chain in Senegal providing vegetables to the local market. The focal organization is Manobi, a Senegalese inclusive business which provides affordable ICT services to local entrepreneurs in the agri-food sector. Case study A provides interesting insights into the dynamics of local supply chains and how professional services can help to improve their performance. Case study B (Section 5.2 in page 122) is a single case study. It analyzes a global supply chain with origin in Ethiopia providing cut flowers to the global commodity market. The focal organization is EHPEA, Ethiopian Horticulture Producers and Exporters Association, whose mission is to promote and safeguard the competitive position of the Ethiopian horticulture sector within the global market. Case study B helps to better understand the suppliers’ perspective regarding global market sustainability requirements and shows how the inclusion of suppliers in the process of development of a private standard has a positive impact in its implementation. Case study C (Section 5.3 in page 143) is a multiple case study. It analyzes a global supply chain with origin in Tanzania providing coffee to the global niche market of specialty coffee. The focal organizations are traders who are directly connecting smallholder coffee farmers in developing countries to coffee roasters in developed countries. Case study C shows how smallholder farmers can supply a premium product and be incorporated in a differentiated market segment through a transparent and efficient supply chain. The empirical findings from the case studies help to validate and refine the conceptual framework (see discussion in Chapter 6). The proposal of a new version of the conceptual framework is depicted in Figure 40 (page 195). The case studies also provide interesting insights related to the management of inclusive supply chains and show the perspectives of the different actors involved. This thesis sheds some light on the role of businesses in the creation and operation of inclusive supply chains by carrying out a cross-disciplinary literature review and analyzing three case studies in African countries. In doing so, this thesis presents a series of theoretical and empirical contributions to the emerging academic field of inclusive supply chains (Chapter 7). This thesis also intends to be useful to practitioners willing to improve the incorporation of the poor as suppliers in fair and profitable conditions.

Applications of Formal Languages to Management of Manned and Unmanned Aircraft

En el futuro, la gestión del tráfico aéreo (ATM, del inglés air traffic management) requerirá un cambio de paradigma, de la gestión principalmente táctica de hoy, a las denominadas operaciones basadas en trayectoria. Un incremento en el nivel de automatización liberará al personal de ATM —controladores, tripulación, etc.— de muchas de las tareas que realizan hoy. Las personas seguirán siendo el elemento central en la gestión del tráfico aéreo del futuro, pero lo serán mediante la gestión y toma de decisiones. Se espera que estas dos mejoras traigan un incremento en la eficiencia de la gestión del tráfico aéreo que permita hacer frente al incremento previsto en la demanda de transporte aéreo. Para aplicar el concepto de operaciones basadas en trayectoria, el usuario del espacio aéreo (la aerolínea, piloto, u operador) y el proveedor del servicio de navegación aérea deben negociar las trayectorias mediante un proceso de toma de decisiones colaborativo. En esta negociación, es necesaria una forma adecuada de compartir dichas trayectorias. Compartir la trayectoria completa requeriría un gran ancho de banda, y la trayectoria compartida podría invalidarse si cambiase la predicción meteorológica. En su lugar, podría compartirse una descripción de la trayectoria independiente de las condiciones meteorológicas, de manera que la trayectoria real se pudiese calcular a partir de dicha descripción. Esta descripción de la trayectoria debería ser fácil de procesar usando un programa de ordenador —ya que parte del proceso de toma de decisiones estará automatizado—, pero también fácil de entender para un operador humano —que será el que supervise el proceso y tome las decisiones oportunas—. Esta tesis presenta una serie de lenguajes formales que pueden usarse para este propósito. Estos lenguajes proporcionan los medios para describir trayectorias de aviones durante todas las fases de vuelo, desde la maniobra de push-back (remolcado hasta la calle de rodaje), hasta la llegada a la terminal del aeropuerto de destino. También permiten describir trayectorias tanto de aeronaves tripuladas como no tripuladas, incluyendo aviones de ala fija y cuadricópteros. Algunos de estos lenguajes están estrechamente relacionados entre sí, y organizados en una jerarquía. Uno de los lenguajes fundamentales de esta jerarquía, llamado aircraft intent description language (AIDL), ya había sido desarrollado con anterioridad a esta tesis. Este lenguaje fue derivado de las ecuaciones del movimiento de los aviones de ala fija, y puede utilizarse para describir sin ambigüedad trayectorias de este tipo de aeronaves. Una variante de este lenguaje, denominada quadrotor AIDL (QR-AIDL), ha sido desarrollada en esta tesis para permitir describir trayectorias de cuadricópteros con el mismo nivel de detalle. Seguidamente, otro lenguaje, denominado intent composite description language (ICDL), se apoya en los dos lenguajes anteriores, ofreciendo más flexibilidad para describir algunas partes de la trayectoria y dejar otras sin especificar. El ICDL se usa para proporcionar descripciones genéricas de maniobras comunes, que después se particularizan y combinan para formar descripciones complejas de un vuelo. Otro lenguaje puede construirse a partir del ICDL, denominado flight intent description language (FIDL). El FIDL especifica requisitos de alto nivel sobre las trayectorias —incluyendo restricciones y objetivos—, pero puede utilizar características del ICDL para proporcionar niveles de detalle arbitrarios en las distintas partes de un vuelo. Tanto el ICDL como el FIDL han sido desarrollados en colaboración con Boeing Research & Technology Europe (BR&TE). También se ha desarrollado un lenguaje para definir misiones en las que interactúan varias aeronaves, el mission intent description language (MIDL). Este lenguaje se basa en el FIDL y mantiene todo su poder expresivo, a la vez que proporciona nuevas semánticas para describir tareas, restricciones y objetivos relacionados con la misión. En ATM, los movimientos de un avión en la superficie de aeropuerto también tienen que ser monitorizados y gestionados. Otro lenguaje formal ha sido diseñado con este propósito, llamado surface movement description language (SMDL). Este lenguaje no pertenece a la jerarquía de lenguajes descrita en el párrafo anterior, y se basa en las clearances (autorizaciones del controlador) utilizadas durante las operaciones en superficie de aeropuerto. También proporciona medios para expresar incertidumbre y posibilidad de cambios en las distintas partes de la trayectoria. Finalmente, esta tesis explora las aplicaciones de estos lenguajes a la predicción de trayectorias y a la planificación de misiones. El concepto de trajectory language processing engine (TLPE) se usa en ambas aplicaciones. Un TLPE es una función de ATM cuya principal entrada y salida se expresan en cualquiera de los lenguajes incluidos en la jerarquía descrita en esta tesis. El proceso de predicción de trayectorias puede definirse como una combinación de TLPEs, cada uno de los cuales realiza una pequeña sub-tarea. Se le ha dado especial importancia a uno de estos TLPEs, que se encarga de generar el perfil horizontal, vertical y de configuración de la trayectoria. En particular, esta tesis presenta un método novedoso para la generación del perfil vertical. El proceso de planificar una misión también se puede ver como un TLPE donde la entrada se expresa en MIDL y la salida consiste en cierto número de trayectorias —una por cada aeronave disponible— descritas utilizando FIDL. Se ha formulado este problema utilizando programación entera mixta. Además, dado que encontrar caminos óptimos entre distintos puntos es un problema fundamental en la planificación de misiones, también se propone un algoritmo de búsqueda de caminos. Este algoritmo permite calcular rápidamente caminos cuasi-óptimos que esquivan todos los obstáculos en un entorno urbano. Los diferentes lenguajes formales definidos en esta tesis pueden utilizarse como una especificación estándar para la difusión de información entre distintos actores de la gestión del tráfico aéreo. En conjunto, estos lenguajes permiten describir trayectorias con el nivel de detalle necesario en cada aplicación, y se pueden utilizar para aumentar el nivel de automatización explotando esta información utilizando sistemas de soporte a la toma de decisiones. La aplicación de estos lenguajes a algunas funciones básicas de estos sistemas, como la predicción de trayectorias, han sido analizadas. ABSTRACT Future air traffic management (ATM) will require a paradigm shift from today’s mainly tactical ATM to trajectory-based operations (TBOs). An increase in the level of automation will also relieve humans —air traffic control officers (ATCOs), flight crew, etc.— from many of the tasks they perform today. Humans will still be central in this future ATM, as decision-makers and managers. These two improvements (TBOs and increased automation) are expected to provide the increase in ATM performance that will allow coping with the expected increase in air transport demand. Under TBOs, trajectories are negotiated between the airspace user (an airline, pilot, or operator) and the air navigation service provider (ANSP) using a collaborative decision making (CDM) process. A suitable method for sharing aircraft trajectories is necessary for this negotiation. Sharing a whole trajectory would require a high amount of bandwidth, and the shared trajectory might become invalid if the weather forecast changed. Instead, a description of the trajectory, decoupled from the weather conditions, could be shared, so that the actual trajectory could be computed from this trajectory description. This trajectory description should be easy to process using a computing program —as some of the CDM processes will be automated— but also easy to understand for a human operator —who will be supervising the process and making decisions. This thesis presents a series of formal languages that can be used for this purpose. These languages provide the means to describe aircraft trajectories during all phases of flight, from push back to arrival at the gate. They can also describe trajectories of both manned and unmanned aircraft, including fixedwing and some rotary-wing aircraft (quadrotors). Some of these languages are tightly interrelated and organized in a language hierarchy. One of the key languages in this hierarchy, the aircraft intent description language (AIDL), had already been developed prior to this thesis. This language was derived from the equations of motion of fixed-wing aircraft, and can provide an unambiguous description of fixed-wing aircraft trajectories. A variant of this language, the quadrotor AIDL (QR-AIDL), is developed in this thesis to allow describing a quadrotor aircraft trajectory with the same level of detail. Then, the intent composite description language (ICDL) is built on top of these two languages, providing more flexibility to describe some parts of the trajectory while leaving others unspecified. The ICDL is used to provide generic descriptions of common aircraft manoeuvres, which can be particularized and combined to form complex descriptions of flight. Another language is built on top of the ICDL, the flight intent description language (FIDL). The FIDL specifies high-level requirements on trajectories —including constraints and objectives—, but can use features of the ICDL to provide arbitrary levels of detail in different parts of the flight. The ICDL and FIDL have been developed in collaboration with Boeing Research & Technology Europe (BR&TE). Also, the mission intent description language (MIDL) has been developed to allow describing missions involving multiple aircraft. This language is based on the FIDL and keeps all its expressive power, while it also provides new semantics for describing mission tasks, mission objectives, and constraints involving several aircraft. In ATM, the movement of aircraft while on the airport surface also has to be monitored and managed. Another formal language has been designed for this purpose, denoted surface movement description language (SMDL). This language does not belong to the language hierarchy described above, and it is based on the clearances used in airport surface operations. Means to express uncertainty and mutability of different parts of the trajectory are also provided. Finally, the applications of these languages to trajectory prediction and mission planning are explored in this thesis. The concept of trajectory language processing engine (TLPE) is used in these two applications. A TLPE is an ATM function whose main input and output are expressed in any of the languages in the hierarchy described in this thesis. A modular trajectory predictor is defined as a combination of multiple TLPEs, each of them performing a small subtask. Special attention is given to the TLPE that builds the horizontal, vertical, and configuration profiles of the trajectory. In particular, a novel method for the generation of the vertical profile is presented. The process of planning a mission can also be seen as a TLPE, where the main input is expressed in the MIDL and the output consists of a number of trajectory descriptions —one for each aircraft available in the mission— expressed in the FIDL. A mixed integer linear programming (MILP) formulation for the problem of assigning mission tasks to the available aircraft is provided. In addition, since finding optimal paths between locations is a key problem to mission planning, a novel path finding algorithm is presented. This algorithm can compute near-shortest paths avoiding all obstacles in an urban environment in very short times. The several formal languages described in this thesis can serve as a standard specification to share trajectory information among different actors in ATM. In combination, these languages can describe trajectories with the necessary level of detail for any application, and can be used to increase automation by exploiting this information using decision support tools (DSTs). Their applications to some basic functions of DSTs, such as trajectory prediction, have been analized.

Modeling and Simulation of Upper Brachial Plexus Injury

This article presents the first musculoskeletal model and simulation of upper plexus brachial injury. From this model is possible to analyse forces and movement ranges in order to develop a robotic exoskeleton to improve rehabilitation. The software that currently exists for musculoskeletal modeling is varied and most have advanced features for proper analysis and study of motion simulations. Whilst more powerful computer packages are usually expensive, there are other free and open source packages available which offer different tools to perform animations and simulations and which obtain forces and moments of inertia. Among them, Musculoskeletal Modeling Software was selected to construct a model of the upper limb, which has 7 degrees of freedom and 10 muscles. These muscles are important for two of the movements simulated in this article that are part of the post-surgery rehabilitation protocol. We performed different movement animations which are made using the inertial measurement unit to capture real data from movements made by a human being. We also performed the simulation of forces produced in elbow flexion-extension and arm abduction-adduction of a healthy subject and one with upper brachial plexus injury in a postoperative state to compare the force that is capable of being produced in both cases.

Membrane-bound state of the colicin E1 channel domain as an extended two-dimensional helical array

Atomic level structures have been determined for the soluble forms of several colicins and toxins, but the structural changes that occur after membrane binding have not been well characterized. Changes occurring in the transition from the soluble to membrane-bound state of the C-terminal 190-residue channel polypeptide of colicin E1 (P190) bound to anionic membranes are described. In the membrane-bound state, the α-helical content increases from 60–64% to 80–90%, with a concomitant increase in the average length of the helical segments from 12 to 16 or 17 residues, close to the length required to span the membrane bilayer in the open channel state. The average distance between helical segments is increased and interhelix interactions are weakened, as shown by a major loss of tertiary structure interactions, decreased efficiency of fluorescence resonance energy transfer from an energy donor on helix V of P190 to an acceptor on helix IX, and decreased resonance energy transfer at higher temperatures, not observed in soluble P190, implying freedom of motion of helical segments. Weaker interactions are also shown by a calorimetric thermal transition of low cooperativity, and the extended nature of the helical array is shown by a 3- to 4-fold increase in the average area subtended per molecule to 4,200 Å2 on the membrane surface. The latter, with analysis of the heat capacity changes, implies the absence of a developed hydrophobic core in the membrane-bound P190. The membrane interfacial layer thus serves to promote formation of a highly helical extended two-dimensional flexible net. The properties of the membrane-bound state of the colicin channel domain (i.e., hydrophobic anchor, lengthened and loosely coupled α-helices, and close association with the membrane interfacial layer) are plausible structural features for the state that is a prerequisite for voltage gating, formation of transmembrane helices, and channel opening.

Characteristic enrichment of DNA repeats in different genomes

Using computer programs developed for this purpose, we searched for various repeated sequences including inverted, direct tandem, and homopurine–homopyrimidine mirror repeats in various prokaryotes, eukaryotes, and an archaebacterium. Comparison of observed frequencies with expectations revealed that in bacterial genomes and organelles the frequency of different repeats is either random or enriched for inverted and/or direct tandem repeats. By contrast, in all eukaryotic genomes studied, we observed an overrepresentation of all repeats, especially homopurine–homopyrimidine mirror repeats. Analysis of the genomic distribution of all abundant repeats showed that they are virtually excluded from coding sequences. Unexpectedly, the frequencies of abundant repeats normalized for their expectations were almost perfect exponential functions of their size, and for a given repeat this function was indistinguishable between different genomes.

Perceptual motion standstill in rapidly moving chromatic displays

In motion standstill, a quickly moving object appears to stand still, and its details are clearly visible. It is proposed that motion standstill can occur when the spatiotemporal resolution of the shape and color systems exceeds that of the motion systems. For moving red-green gratings, the first- and second-order motion systems fail when the grating is isoluminant. The third-order motion system fails when the green/red saturation ratio produces isosalience (equal distinctiveness of red and green). When a variety of high-contrast red-green gratings, with different spatial frequencies and speeds, were made isoluminant and isosalient, the perception of motion standstill was so complete that motion direction judgments were at chance levels. Speed ratings also indicated that, within a narrow range of luminance contrasts and green/red saturation ratios, moving stimuli were perceived as absolutely motionless. The results provide further evidence that isoluminant color motion is perceived only by the third-order motion system, and they have profound implications for the nature of shape and color perception.

Comparative mapping of the human 22q11 chromosomal region and the orthologous region in mice reveals complex changes in gene organization

The region of human chromosome 22q11 is prone to rearrangements. The resulting chromosomal abnormalities are involved in Velo-cardio-facial and DiGeorge syndromes (VCFS and DGS) (deletions), “cat eye” syndrome (duplications), and certain types of tumors (translocations). As a prelude to the development of mouse models for VCFS/DGS by generating targeted deletions in the mouse genome, we examined the organization of genes from human chromosome 22q11 in the mouse. Using genetic linkage analysis and detailed physical mapping, we show that genes from a relatively small region of human 22q11 are distributed on three mouse chromosomes (MMU6, MMU10, and MMU16). Furthermore, although the region corresponding to about 2.5 megabases of the VCFS/DGS critical region is located on mouse chromosome 16, the relative organization of the region is quite different from that in humans. Our results show that the instability of the 22q11 region is not restricted to humans but may have been present throughout evolution. The results also underscore the importance of detailed comparative mapping of genes in mice and humans as a prerequisite for the development of mouse models of human diseases involving chromosomal rearrangements.

Real-Time Imaging of the Axonal Transport of Granules Containing a Tissue Plasminogen Activator/Green Fluorescent Protein Hybrid

A hybrid protein, tPA/GFP, consisting of rat tissue plasminogen activator (tPA) and green fluorescent protein (GFP) was expressed in PC12 cells and used to study the distribution, secretory behavior, and dynamics of secretory granules containing tPA in living cells with a neuronal phenotype. High-resolution images demonstrate that tPA/GFP has a growth cone-biased distribution in differentiated cells and that tPA/GFP is transported in granules of the regulated secretory pathway that colocalize with granules containing secretogranin II. Time-lapse images of secretion reveal that secretagogues induce substantial loss of cellular tPA/GFP fluorescence, most importantly from growth cones. Time-lapse images of the axonal transport of granules containing tPA/GFP reveal a surprising complexity to granule dynamics. Some granules undergo canonical fast axonal transport; others move somewhat more slowly, especially in highly fluorescent neurites. Most strikingly, granules traffic bidirectionally along neurites to an extent that depends on granule accumulation, and individual granules can reverse their direction of motion. The retrograde component of this bidirectional transport may help to maintain cellular homeostasis by transporting excess tPA/GFP back toward the cell body. The results presented here provide a novel view of the axonal transport of secretory granules. In addition, the results suggest that tPA is targeted for regulated secretion from growth cones of differentiated cells, strategically positioning tPA to degrade extracellular barriers or to activate other barrier-degrading proteases during axonal elongation.