SCANNERS: constraining the phase diagram of a complex scalar singlet at the LHC

We present the first version of a new tool to scan the parameter space of generic scalar potentials, SCANNERS (Coimbra et al., SCANNERS project., 2013). The main goal of SCANNERS is to help distinguish between different patterns of symmetry breaking for each scalar potential. In this work we use it to investigate the possibility of excluding regions of the phase diagram of several versions of a complex singlet extension of the Standard Model, with future LHC results. We find that if another scalar is found, one can exclude a phase with a dark matter candidate in definite regions of the parameter space, while predicting whether a third scalar to be found must be lighter or heavier. The first version of the code is publicly available and contains various generic core routines for tree level vacuum stability analysis, as well as implementations of collider bounds, dark matter constraints, electroweak precision constraints and tree level unitarity.

Optoelectronic properties of a-Si(1-x)C(x)H films grown in hydrogen diluted silane-methane plasma

This work reports on the optoelectronic properties and device application of hydrogenated amorphous silicon carbide (a-Si(1-x)C(x):H) films grown by plasma-enhanced chemical vapour deposition (PECVD). The films with an optical bandgap ranging from about 1.8 to 2.0 eV were deposited in hydrogen diluted silane-methane plasma by varying the radio frequency power. Several n-i-p structures with an intrinsic a-Si(1-x)C(x):H layer of different optical gaps were also fabricated. The optimized devices exhibited a diode ideality factor of 1.4-1.8, and a leakage current of 190-470 pA/cm(2) at -5 V. The density of deep defect states in a-Si(1-x)C(x):H was estimated from the transient dark current measurements and correlated with the optical bandgap and carbon content. Urbach energies for the valence band tail were also determined by analyzing the spectral response within sub-bandgap energy range. (C) 2010 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim

Basic dyestuffs removal from textile effluents using feathers: equilibrium, kinetic and column studies

This research work has been focused in the study of gallinaceous feathers, a waste that may be valorised as sorbent, to remove the Dark Blue Astrazon 2RN (DBA) from Dystar. This study was focused on the following aspects: optimization of experimental conditions through factorial design methodology, kinetic studies into a continuous stirred tank adsorber (at pH 7 and 20ºC), equilibrium isotherms (at pH 5, 7 and 9 at 20 and 45ºC) and column studies (at 20ºC, at pH 5, 7 and 9). In order to evaluate the influence of the presence of other components in the sorption of the dyestuff, all experiments were performed both for the dyestuff in aqueous solution and in real textile effluent. The pseudo-first and pseudo-second order kinetic models were fitted to the experimental data, being the latter the best fit for the aqueous solution of dyestuff. For the real effluent both models fit the experimental results and there is no statistical difference between them. The Central Composite Design (CCD) was used to evaluate the effects of temperature (15 - 45ºC) and pH (5 - 9) over the sorption in aqueous solution. The influence of pH was more significant than temperature. The optimal conditions selected were 45ºC and pH 9. Both Langmuir and Freundlich models could fit the equilibrium data. In the concentration range studied, the highest sorbent capacity was obtained for the optimal conditions in aqueous solution, which corresponds to a maximum capacity of 47± 4 mg g-1. The Yoon-Nelson, Thomas and Yan’s models fitted well the column experimental data. The highest breakthrough time for 50% removal, 170 min, was obtained at pH 9 in aqueous solution. The presence of the dyeing agents in the real wastewater decreased the sorption of the dyestuff mostly for pH 9, which is the optimal pH. The effect of pH is less pronounced in the real effluent than in aqueous solution. This work shows that feathers can be used as sorbent in the treatment of textile wastewaters containing DBA.

Cryptotermes brevis (Isoptera: Kalotermitidae) in the Azores : Lessons After 2 yr of Monitoring in the Archipelago

The dispersal flights of West Indian drywood termite, Cryptotermes brevis (Walker) (Isoptera: Kalotermitidae) were surveyed in the major cities of Azores. The sampling device used to estimate termite density consisted of a yellow adhesive trap (size 45 by 24 cm), placed with an artificial or natural light source in a dark attic environment. In addition, data from two other projects were used to improve the knowledge about the geographical distribution of the species. The level of infestation in the two main Azorean towns differed, with high levels in the houses of Angra do Heroísmo, whereas in Ponta Delgada, there are fewer houses with high levels of infestation. The infestation in Ponta Delgada shows a pattern of spreading from the center outward to the city's periphery, whereas in Angra do Heroísmo, there was a pattern of spreading outward from several foci. The heavy infestation observed in Angra do Heroísmo and the clear increase of infestation levels observed from 2010 to 2011 is a reason for concern and calls for an urgent application of an Integrated Pest Management (IPM) control strategy.

Estudo da influência das condições de armazenamento nas propriedades e composição do biodiesel

O objectivo deste trabalho era a determinação da influência das condições de armazenamento do biodiesel nas suas propriedades e composição. Para isso foi produzido biodiesel a partir de óleo alimentar usado e armazenado em diferentes condições. O biodiesel foi colocado em frascos de vidro e dividido em três grupos diferentes de temperatura. O primeiro foi colocado a uma temperatura de 6ºC (frigorifico) com frascos fechados e expostos ao ar e água. O segundo grupo foi colocado a uma temperatura de 40ºC (banho termostático) com frascos fechados, abertos ao ar e abertos ao ar e água. O terceiro e ultimo grupo foi colocado à temperatura ambiente (18,6

Avaliação do desempenho de adsorventes obtidos a partir de resíduos da indústria de curtumes na adsorção de poluentes

Na procura por uma solução de valorização dos resíduos gerados pela indústria de curtumes, o presente trabalho tem como principais objectivos a preparação de adsorventes a partir de resíduos desta actividade e a avaliação do seu desempenho na adsorção de poluentes. Para atingir este objectivo, inicialmente procedeu-se à carbonização das aparas de couro wet-white à temperatura de 800 ºC. Seguidamente, os carbonizados foram activados por activação química, tendo sido o hidróxido de potássio o agente activante escolhido. As razões mássicas hidróxido de potássio:precursor usadas na impregnação, foram iguais a 0,5:1 e 1:1. Para a razão 0,5:1, as temperaturas de activação escolhidas foram 700 e 800 ºC. Para a razão de impregnação 1:1, as temperaturas de activação usadas foram 700, 800 e 900 ºC. Para uma avaliação preliminar da capacidade de adsorção dos carvões activados produzidos, efectuou-se a determinação do número de azul de metileno. Este teste provou serem as amostras activadas a 900 ºC as que apresentaram melhores resultados (número de azul de metileno: 24g/100g) e as amostras activadas a 700 ºC, as que apresentaram menor capacidade de adsorção (1g/100g, para a razão de 0,5:1 e 7g/100g, para a razão de 1:1). Verificou-se também que amostras preparadas com iguais condições de activação (temperatura de activação e razão de impregnação), mas produzidas a partir de carbonizado de diferentes granulometrias, apresentaram diferentes desempenhos na adsorção de azul de metileno. As propriedades texturais dos carvões activados produzidos foram obtidas pela determinação das isotérmicas de adsorção de azoto a 77 K. Para tal, selecionaram-se quatro amostras: dois carvões activados a 800 ºC, com uma razão de impregnação de 1:1 e dois carvões activados a 900 ºC, com a mesma razão de impregnação, obtidos a partir de carbonizados com diferentes granulometrias. As isotérmicas obtidas são características de materiais essencialmente microporosos, com mesoporos e macroporos. Verificou-se também que a granulometria do precursor carbonizado influencia as propriedades texturais dos carvões activados produzidos. Para as temperaturas de activação usadas, 800 e 900 ºC, os carvões activados preparados a partir de carbonizado de menor granulometria apresentam melhores propriedades texturais. O carvão activado que apresentou maior área superficial específica foi obtido a 900 ºC, a partir de carbonizado finamente moído (SBET = 1475 m2/g). Determinadas as propriedades texturais dos carvões activados produzidos, realizaram-se ensaios de adsorção do corante CORIACIDE DARK BROWN VR, usado na indústria de curtumes com um carvão activado produzido no âmbito deste trabalho e com um carvão activado comercial NORIT ROW 0,8. A amostra de carvão activado produzida a partir de resíduos de wet-white escolhida para estes ensaios foi o carvão activado a 800 ºC, à razão de 1:1, a partir de carbonizado finamente moído (ww_800_1:1_carb.moído). Verificou-se que as quantidades adsorvidas pela amostra ww_800_1:1_carb.moído variaram entre os valores 7,47 e 32,07 mgcorante/gcarvão activado. Quanto ao carvão activado comercial, as quantidades adsorvidas situaram-se entre 8,95 e 69,13 mgcorante/gcarvão activado. Assim, conclui-se que o carvão activado comercial apresentou melhor desempenho na adsorção do corante da indústria de curtumes. Os carvões activados obtidos revelaram-se materiais essencialmente microporosos, com capacidade de adsorção de poluentes, como por exemplo corantes, no entanto o seu desempenho seria mais eficaz na adsorção de pequenas moléculas devido ao elevado volume de microporos que apresentaram.

Shear-induced lamellar phase of an ionic liquid crystal at room temperature

The phase behaviour of a number of N-alkylimidazolium salts was studied using polarizing optical microscopy, differential scanning calorimetry and X-ray diffraction. Two of these compounds exhibit lamellar mesophases at temperatures above 50 degrees C. In these systems, the liquid crystalline behaviour may be induced at room temperature by shear. Sheared films of these materials, observed between crossed polarisers, have a morphology that is typical of (wet) liquid foams: they partition into dark domains separated by brighter (birefringent) walls, which are approximately arcs of circle and meet at "Plateau borders" with three or more sides. Where walls meet three at a time, they do so at approximately 120 degrees angles. These patterns coarsen with time and both T1 and T2 processes have been observed, as in foams. The time evolution of domains is also consistent with von Neumann's law. We conjecture that the bright walls are regions of high concentration of defects produced by shear, and that the system is dominated by the interfacial tension between these walls and the uniform domains. The control of self-organised monodomains, as observed in these systems, is expected to play an important role in potential applications.

How foam-like is the shear-induced lamellar phase of an ionic liquid crystal?

Philosophical Magazine Letters Volume 88, Issue 9-10, 2008 Special Issue: Solid and Liquid Foams. In commemoration of Manuel Amaral Fortes

Brewer's spent grain from different types of malt: Evaluation of the antioxidant activity and identification of the major phenolic compounds

The antioxidant activity and phenolic composition of brewer's spent grain (BSG) extracts obtained by microwave-assisted extraction from twomalt types (light and darkmalts) were investigated. The total phenolic content (TPC) and antioxidant activity among the light BSG extracts (pilsen, melano, melano 80 and carared)were significantly different (p b 0.05) compared to dark extracts (chocolate and black types), with the pilsen BSG showing higher TPC (20 ± 1 mgGAE/g dry BSG). In addition, the antioxidant activity assessed by 2,2-diphenyl- 1-picrylhydrazyl, 2,2′-azino-bis(3-ethylbenzothiazoline-6-sulfonic acid) and deoxyribose assays decreased as a result of increasing kilning temperatures in the following order: pilsen N melano N melano 80 N carared N chocolate N black. HPLC-DAD/ESI-MS/MS analysis indicated the presence of phenolic acids, such as ferulic, p-coumaric and syringic acids, as well as several isomeric ferulate dehydrodimers and one dehydrotrimer. Chocolate and black extracts, obtained frommalts submitted to the highest kilning temperatures, showed the lowest levels of ferulic and p-coumaric acids. These results suggested that BSG extracts from pilsen malt might be used as an inexpensive and good natural source of antioxidants with potential interest for the food, pharmaceutical and/or cosmetic industries after purification.

Properties of tantalum oxynitride thin films produced by magnetron sputtering: the influence of processing parameters

The main purpose of this work is to present and to interpret the change of structure and physical properties of tantalum oxynitride (TaNxOy) thin films, produced by dc reactive magnetron sputtering, by varying the processing parameters. A set of TaNxOy films was prepared by varying the reactive gases flow rate, using a N2/O2 gas mixture with a concentration ratio of 17:3. The different films, obtained by this process, exhibited significant differences. The obtained composition and the interpretation of X-ray diffraction results, shows that, depending on the partial pressure of the reactive gases, the films are: essentially dark grey metallic, when the atomic ratio (N + O)/Ta < 0.1, evidencing a tetragonal β-Ta structure; grey-brownish, when 0.1 < (N + O)/Ta < 1, exhibiting a face-centred cubic (fcc) TaN-like structure; and transparent oxide-type, when (N + O)/Ta > 1, evidencing the existence of Ta2O5, but with an amorphous structure. These transparent films exhibit refractive indexes, in the visible region, always higher than 2.0. The wear resistance of the films is relatively good. The best behaviour was obtained for the films with (N + O)/Ta ≈ 0.5 and (N + O)/Ta ≈ 1.3.

Add/drop filters based on SiC technology for optical interconnects

In this paper we demonstrate an add/drop filter based on SiC technology. Tailoring of the channel bandwidth and wavelength is experimentally demonstrated. The concept is extended to implement a 1 by 4 wavelength division multiplexer with channel separation in the visible range. The device consists of a p-i'(a-SiC:H)-n/p-i(a-Si: H)-n heterostructure. Several monochromatic pulsed lights, separately or in a polychromatic mixture illuminated the device. Independent tuning of each channel is performed by steady state violet bias superimposed either from the front and back sides. Results show that, front background enhances the light-to-dark sensitivity of the long and medium wavelength channels and quench strongly the others. Back violet background has the opposite behaviour. This nonlinearity provides the possibility for selective removal or addition of wavelengths. An optoelectronic model is presented and explains the light filtering properties of the add/drop filter, under different optical bias conditions.

Liquid crystal beads constrained on thin cellulosic fibers: Electric field induced microrotors and N-I transition

We directly visualize the response of nematic liquid crystal drops of toroidal topology threaded in cellulosic fibers, suspended in air, to an AC electric field and at different temperatures over the N-I transition. This new liquid crystal system can exhibit non-trivial point defects, which can be energetically unstable against expanding into ring defects depending on the fiber constraining geometries. The director anchoring tangentially near the fiber surface and homeotropically at the air interface makes a hybrid shell distribution that in turn causes a ring disclination line around the main axis of the fiber at the center of the droplet. Upon application of an electric field, E, the disclination ring first expands and moves along the fiber main axis, followed by the appearance of a stable "spherical particle" object orbiting around the fiber at the center of the liquid crystal drop. The rotation speed of this particle was found to vary linearly with the applied voltage. This constrained liquid crystal geometry seems to meet the essential requirements in which soliton-like deformations can develop and exhibit stable orbiting in three dimensions upon application of an external electric field. On changing the temperature the system remains stable and allows the study of the defect evolution near the nematic-isotropic transition, showing qualitatively different behaviour on cooling and heating processes. The necklaces of such liquid crystal drops constitute excellent systems for the study of topological defects and their evolution and open new perspectives for application in microelectronics and photonics.

A rede GÉANT e as tendências de desenvolvimento das novas redes de comunicação em fibra óptica

Trabalho realizado sob orientação do Prof. António Brandão Moniz para a disciplina “Factores Sociais da Inovação” do Mestrado Engenharia Informática realizado na Faculdade de Ciências e Tecnologia da Universidade Nova de Lisboa (Portugal).

Pliocene-quaternary upwelling in the SoutheasternAtlantic may reflect changes in water mass production

Proceedings of tile 1" R.C.A.N.S. Congress, Lisboa, October 1992

Partitura de luz: a representação criativa como perspectiva educacional

Este projecto de investigação teve como objectivo avaliar - através de uma série de workshops orientados pela mestranda no Centro Cultural de Belém em Abril de 2012 - o impacto da utilização de notação musical não-convencional num contexto não escolar. Traçando possíveis paralelos com o ensino especializado da música, propuseram-se metodologias de aprendizagem que permitissem a introdução da notação, de forma inovadora, no referido contexto escolar. O processo de investigação baseou-se em observação directa, na análise dos questionários preenchidos pelos participantes dos workshops e na observação e análise das gravações em vídeo que documentaram o processo artístico, pedagógico e de investigação. Numa sala escura, 6 retroprojectores projectaram uma Partitura de Luz. Entre crianças e adultos, 120 participantes (não-músicos) criaram empiricamente as suas composições, moldando o som em função da forma e a forma em função do som. O resultado foi compensador: a criação de condições favoráveis ao desenvolvimento máximo da expressão criativa individual ou colectiva dos participantes - através da utilização irrestrita de símbolos, imagens, objectos e matérias - culminou num efectivo estabelecimento de correspondência musical, a partir de recursos vocais. Este projecto, “Partitura de Luz”, foi uma oportunidade de relacionar a vertente artística – musical, plástica e gráfica - com a vertente humana: pedagógica e social.