Design of a Low Power – High Temperature Heated Ceramic Sensor to Detect Halogen Gases

The design, construction and optimization of a low power-high temperature heated ceramic sensor to detect leaking of halogen gases in refrigeration systems are presented. The manufacturing process was done with microelectronic assembly and the Low Temperature Cofire Ceramic (LTCC) technique. Four basic sensor materials were fabricated and tested: Li2SiO3, Na2SiO3, K2SiO3, and CaSiO3. The evaluation of the sensor material, sensor size, operating temperature, bias voltage, electrodes size, firing temperature, gas flow, and sensor life was done. All sensors responded to the gas showing stability and reproducibility. Before exposing the sensor to the gas, the sensor was modeled like a resistor in series and the calculations obtained were in agreement with the experimental values. The sensor response to the gas was divided in surface diffusion and bulk diffusion; both were analyzed showing agreement between the calculations and the experimental values. The sensor with 51.5%CaSiO3 + 48.5%Li2SiO3 shows the best results, including a stable current and response to the gas.

Estudo da previsão da carga de ruptura de estacas pré-moldadas de concreto

The piles are one of the most important types of solution adopted for the foundation of buildings. They are responsible for transmitting to the soil in deepe r and resistant layers loads from structures. The interaction of the foundation element with the soil is a very important variable, making indispensable your domain in order to determine the strength of the assembly and establish design criteria for each c ase of application of the pile. In this research analyzes were performed f rom experiments load tests for precast concrete piles and inve stigations of soil of type SPT, a study was performed for obtaining the ultimate load capacity of the foundation through methods extrapolation of load - settlement curve , semi - empirical and theoretic . After that, were realized comparisons between the different methods used for two types of soil a granular behavior and other cohesive. For obtaining soil paramet ers to be used i n the methods were established empirical correlations with the standard penetration number (NSPT). The charge - settlement curves of the piles are also analyzed. In the face of established comparisons was indicated the most reliable semiempirical method Déco urt - Quaresma as the most reliable for estimating the tensile strength for granular and cohesive soils. Meanwhile, among the methods studied extrapolation is recommended method of Van der Veen as the most appropriate for predicting the tensile strength.

The nature of alkanethiol self-assembled monolayer adsorption on sputtered gold substrates

A detailed study of the self-assembly and coverage by 1-nonanethiol of sputtered Au surfaces using molecular resolution atomic force microscopy (AFM) and scanning tunneling microscopy (STM) is presented. The monolayer self-assembles on a smooth Au surface composed predominantly of {111} oriented grains. The domains of the alkanethiol monolayer are observed with sizes typically of 5-25 nm, and multiple molecular domains can exist within one Au grain. STM imaging shows that the (4 × 2) superlattice structure is observed as a (3 × 2√3) structure when imaged under noncontact AFM conditions. The 1-nonanethiol molecules reside in the threefold hollow sites of the Au{111} lattice and aligned along its lattice vectors. The self-assembled monolayer (SAM) contains many nonuniformities such as pinholes, domain boundaries, and monatomic depressions which are present in the Au surface prior to SAM adsorption. The detailed observations demonstrate limitations to the application of 1-nonanethiol as a resist in atomic nanolithography experiments to feature sizes of ∼20 nm.

Towards the design of monolithic decoupled XYZ compliant parallel mechanisms for multi-function applications

This paper deals with the monolithic decoupled XYZ compliant parallel mechanisms (CPMs) for multi-function applications, which can be fabricated monolithically without assembly and has the capability of kinetostatic decoupling. At first, the conceptual design of monolithic decoupled XYZ CPMs is presented using identical spatial compliant multi-beam modules based on a decoupled 3-PPPR parallel kinematic mechanism. Three types of applications: motion/positioning stages, force/acceleration sensors and energy harvesting devices are described in principle. The kinetostatic and dynamic modelling is then conducted to capture the displacements of any stage under loads acting at any stage and the natural frequency with the comparisons with FEA results. Finally, performance characteristics analysis for motion stage applications is detailed investigated to show how the change of the geometrical parameter can affect the performance characteristics, which provides initial optimal estimations. Results show that the smaller thickness of beams and larger dimension of cubic stages can improve the performance characteristics excluding natural frequency under allowable conditions. In order to improve the natural frequency characteristic, a stiffness-enhanced monolithic decoupled configuration that is achieved through employing more beams in the spatial modules or reducing the mass of each cubic stage mass can be adopted. In addition, an isotropic variation with different motion range along each axis and same payload in each leg is proposed. The redundant design for monolithic fabrication is introduced in this paper, which can overcome the drawback of monolithic fabrication that the failed compliant beam is difficult to replace, and extend the CPM’s life.

Testing of Interposer-Based 2.5D Integrated Circuits

The unprecedented and relentless growth in the electronics industry is feeding the demand for integrated circuits (ICs) with increasing functionality and performance at minimum cost and power consumption. As predicted by Moore's law, ICs are being aggressively scaled to meet this demand. While the continuous scaling of process technology is reducing gate delays, the performance of ICs is being increasingly dominated by interconnect delays. In an effort to improve submicrometer interconnect performance, to increase packing density, and to reduce chip area and power consumption, the semiconductor industry is focusing on three-dimensional (3D) integration. However, volume production and commercial exploitation of 3D integration are not feasible yet due to significant technical hurdles.

At the present time, interposer-based 2.5D integration is emerging as a precursor to stacked 3D integration. All the dies and the interposer in a 2.5D IC must be adequately tested for product qualification. However, since the structure of 2.5D ICs is different from the traditional 2D ICs, new challenges have emerged: (1) pre-bond interposer testing, (2) lack of test access, (3) limited ability for at-speed testing, (4) high density I/O ports and interconnects, (5) reduced number of test pins, and (6) high power consumption. This research targets the above challenges and effective solutions have been developed to test both dies and the interposer.

The dissertation first introduces the basic concepts of 3D ICs and 2.5D ICs. Prior work on testing of 2.5D ICs is studied. An efficient method is presented to locate defects in a passive interposer before stacking. The proposed test architecture uses e-fuses that can be programmed to connect or disconnect functional paths inside the interposer. The concept of a die footprint is utilized for interconnect testing, and the overall assembly and test flow is described. Moreover, the concept of weighted critical area is defined and utilized to reduce test time. In order to fully determine the location of each e-fuse and the order of functional interconnects in a test path, we also present a test-path design algorithm. The proposed algorithm can generate all test paths for interconnect testing.

In order to test for opens, shorts, and interconnect delay defects in the interposer, a test architecture is proposed that is fully compatible with the IEEE 1149.1 standard and relies on an enhancement of the standard test access port (TAP) controller. To reduce test cost, a test-path design and scheduling technique is also presented that minimizes a composite cost function based on test time and the design-for-test (DfT) overhead in terms of additional through silicon vias (TSVs) and micro-bumps needed for test access. The locations of the dies on the interposer are taken into consideration in order to determine the order of dies in a test path.

To address the scenario of high density of I/O ports and interconnects, an efficient built-in self-test (BIST) technique is presented that targets the dies and the interposer interconnects. The proposed BIST architecture can be enabled by the standard TAP controller in the IEEE 1149.1 standard. The area overhead introduced by this BIST architecture is negligible; it includes two simple BIST controllers, a linear-feedback-shift-register (LFSR), a multiple-input-signature-register (MISR), and some extensions to the boundary-scan cells in the dies on the interposer. With these extensions, all boundary-scan cells can be used for self-configuration and self-diagnosis during interconnect testing. To reduce the overall test cost, a test scheduling and optimization technique under power constraints is described.

In order to accomplish testing with a small number test pins, the dissertation presents two efficient ExTest scheduling strategies that implements interconnect testing between tiles inside an system on chip (SoC) die on the interposer while satisfying the practical constraint that the number of required test pins cannot exceed the number of available pins at the chip level. The tiles in the SoC are divided into groups based on the manner in which they are interconnected. In order to minimize the test time, two optimization solutions are introduced. The first solution minimizes the number of input test pins, and the second solution minimizes the number output test pins. In addition, two subgroup configuration methods are further proposed to generate subgroups inside each test group.

Finally, the dissertation presents a programmable method for shift-clock stagger assignment to reduce power supply noise during SoC die testing in 2.5D ICs. An SoC die in the 2.5D IC is typically composed of several blocks and two neighboring blocks that share the same power rails should not be toggled at the same time during shift. Therefore, the proposed programmable method does not assign the same stagger value to neighboring blocks. The positions of all blocks are first analyzed and the shared boundary length between blocks is then calculated. Based on the position relationships between the blocks, a mathematical model is presented to derive optimal result for small-to-medium sized problems. For larger designs, a heuristic algorithm is proposed and evaluated.

In summary, the dissertation targets important design and optimization problems related to testing of interposer-based 2.5D ICs. The proposed research has led to theoretical insights, experiment results, and a set of test and design-for-test methods to make testing effective and feasible from a cost perspective.

The Philippines in the Electronics & Electrical Global Value Chain

This report uses the Duke CGGC global value chain (GVC) framework to examine the role of the Philippines in the global electronics & electrical (E&E) industry and identify opportunities to upgrade. Electronics and electrical equipment have played an important role in the Philippine economy since the 1970s and form the foundation of the country’s export basket today. In 2014, these sectors accounted for 47% of total exports from the Philippines at US$28.8 billion, of which 41% was from electronics, and 6% from electrical products. From a global perspective, while the Philippines is not the leading exporter in any particular product category, it is known for its significant number of semiconductor assembly and test (A&T) facilities. The global economic crisis (2008-09), combined with the exit of Intel (2009), had a significant negative impact on electronics exports and, although steadily increasing, they have not yet rebounded to pre-crisis levels. Nonetheless, investment in the E&E industries has picked up since 2010; in the past five years, there have been 110 new investments in these sectors. Another positive sign is the low exit rate; with the exception of Intel, companies that have invested in the Philippines have stayed, with several operations dating back to the late 1970s and 1980s. These firms have not only stayed, but have continued to grow and expand in the country due to the quality of the workforce and satisfaction with the Philippine Economic Zone Authority (PEZA) environment. The growth of the industry has significantly benefited from foreign investment and close ties with Japanese firms.

Fabrication of sub-10 nm lamellar structures by solvent vapour annealing of block copolymers

Fabrication of nanoscale patterns through the bottom-up approach of self-assembly of phase-separated block copolymers (BCP) holds promise for nanoelectronics applications. For lithographic applications, it is useful to vary the morphology of BCPs by monitoring various parameters to make “from lab to fab” a reality. Here I report on the solvent annealing studies of lamellae forming polystyrene-blockpoly( 4-vinylpyridine) (PS-b-P4VP). The high Flory-Huggins parameter (χ = 0.34) of PS-b-P4VP makes it an ideal BCP system for self-assembly and template fabrication in comparison to other BCPs. Different molecular weights of symmetric PS-b-P4VP BCPs forming lamellae patterns were used to produce nanostructured thin films by spin-coating from mixture of toluene and tetrahydrofuran(THF). In particular, the morphology change from micellar structures to well-defined microphase separated arrangements is observed. Solvent annealing provides a better alternative to thermal treatment which often requires long annealing periods. The choice of solvent (single and dual solvent exposure) and the solvent annealing conditions have significant effects on the morphology of films and it was found that a block neutral solvent was required to realize vertically aligned PS and P4VP lamellae. Here, we have followed the formation of microdomain structures with time development at different temperatures by atomic force microscopy (AFM). The highly mobilized chains phase separate quickly due to high Flory-Huggins (χ) parameter. Ultra-small feature size (~10 nm pitch size) nanopatterns were fabricated by using low molecular weight PSb- P4VP (PS and P4VP blocks of 3.3 and 3.1 kg mol-1 respectively). However, due to the low etch contrast between the blocks, pattern transfer of the BCP mask is very challenging. To overcome the etch contrast problem, a novel and simple in-situ hard mask technology is used to fabricate the high aspect ratio silicon nanowires. The lamellar structures formed after self-assembly of phase separated PS-b-P4VP BCPs were used to fabricate iron oxide nanowires which acted as hard mask material to facilitate the pattern transfer into silicon and forming silicon nanostructures. The semiconductor and optical industries have shown significant interest in two dimensional (2D) molybdenum disulphide (MoS2) as a potential device material due to its low band gap and high mobility. However, current methods for its synthesis are not ‘fab’ friendly and require harsh environments and processes. Here, I also report a novel method to prepare MoS2 layered structures via self-assembly of a PS-b-P4VP block copolymer system. The formation of the layered MoS2 was confirmed by XPS, Raman spectroscopy and high resolution transmission electron microscopy.

A Micro-Opto-Electro-Mechanical System (MOEMS) for Microstructure Manipulation

Microstructure manipulation is a fundamental process to the study of biology and medicine, as well as to advance micro- and nano-system applications. Manipulation of microstructures has been achieved through various microgripper devices developed recently, which lead to advances in micromachine assembly, and single cell manipulation, among others. Only two kinds of integrated feedback have been demonstrated so far, force sensing and optical binary feedback. As a result, the physical, mechanical, optical, and chemical information about the microstructure under study must be extracted from macroscopic instrumentation, such as confocal fluorescence microscopy and Raman spectroscopy. In this research work, novel Micro-Opto-Electro-Mechanical-System (MOEMS) microgrippers are presented. These devices utilize flexible optical waveguides as gripping arms, which provide the physical means for grasping a microobject, while simultaneously enabling light to be delivered and collected. This unique capability allows extensive optical characterization of the structure being held such as transmission, reflection, or fluorescence. The microgrippers require external actuation which was accomplished by two methods: initially with a micrometer screw, and later with a piezoelectric actuator. Thanks to a novel actuation mechanism, the “fishbone”, the gripping facets remain parallel within 1 degree. The design, simulation, fabrication, and characterization are systematically presented. The devices mechanical operation was verified by means of 3D finite element analysis simulations. Also, the optical performance and losses were simulated by the 3D-to-2D effective index (finite difference time domain FDTD) method as well as 3D Beam Propagation Method (3D-BPM). The microgrippers were designed to manipulate structures from submicron dimensions up to approximately 100 µm. The devices were implemented in SU-8 due to its suitable optical and mechanical properties. This work demonstrates two practical applications: the manipulation of single SKOV-3 human ovarian carcinoma cells, and the detection and identification of microparts tagged with a fluorescent “barcode” implemented with quantum dots. The novel devices presented open up new possibilities in the field of micromanipulation at the microscale, scalable to the nano-domain.

Representación política y derechos de las trabajadoras en Argentina. El caso de la Convención Constituyente de 1957

A partir de la indagación de los diarios de sesiones de la asamblea constituyente y periódicos partidarios y comerciales, entre otras fuentes, este artículo examina las formulaciones y debates en torno al artículo 14 bis de la Constitución Argentina de 1957. En particular, se resaltará el aporte de las mujeres que actuaron en ese debate quienes establecieron interpretaciones distintas de las existentes hasta ese momento. En ese camino, el estudio arroja luz sobre la dimensión jurídica y política de un tema que no ha sido considerado hasta la fecha en esta normativa: los derechos de las trabajadoras. Las características específicas de los debates y el artículo final de proporcionar una visión de género de esta ley a fin de tener en cuenta dos dimensiones: cómo la política construye el género y cómo éste construye la política

Representación política y derechos de las trabajadoras en Argentina. El caso de la Convención Constituyente de 1957

A partir de la indagación de los diarios de sesiones de la asamblea constituyente y periódicos partidarios y comerciales, entre otras fuentes, este artículo examina las formulaciones y debates en torno al artículo 14 bis de la Constitución Argentina de 1957. En particular, se resaltará el aporte de las mujeres que actuaron en ese debate quienes establecieron interpretaciones distintas de las existentes hasta ese momento. En ese camino, el estudio arroja luz sobre la dimensión jurídica y política de un tema que no ha sido considerado hasta la fecha en esta normativa: los derechos de las trabajadoras. Las características específicas de los debates y el artículo final de proporcionar una visión de género de esta ley a fin de tener en cuenta dos dimensiones: cómo la política construye el género y cómo éste construye la política

Representación política y derechos de las trabajadoras en Argentina. El caso de la Convención Constituyente de 1957

A partir de la indagación de los diarios de sesiones de la asamblea constituyente y periódicos partidarios y comerciales, entre otras fuentes, este artículo examina las formulaciones y debates en torno al artículo 14 bis de la Constitución Argentina de 1957. En particular, se resaltará el aporte de las mujeres que actuaron en ese debate quienes establecieron interpretaciones distintas de las existentes hasta ese momento. En ese camino, el estudio arroja luz sobre la dimensión jurídica y política de un tema que no ha sido considerado hasta la fecha en esta normativa: los derechos de las trabajadoras. Las características específicas de los debates y el artículo final de proporcionar una visión de género de esta ley a fin de tener en cuenta dos dimensiones: cómo la política construye el género y cómo éste construye la política

Aboveground plant biomass from the Jena Experiment (Monocultures, year 2003)

This data set contains aboveground plant biomass in 2003 (Sown plant community, Weed plant community, and Dead plant material; all measured in biomass as dry weight) of the monoculture plots of a large grassland biodiversity experiment (the Jena Experiment). In the monoculture plots the biomass of the sown plant community contains only a single species per plot and this species is a different one for each plot. Which species has been sown in which plot is stated in the plot information table for monocultures (see further details below). The monoculture plots of 3.5 x 3.5 m were established for all of the 60 plant species of the Jena Experiment species pool with two replicates per species. These 60 species comprising the species pool of the Jena Experiment belong to four functional groups (grasses, legumes, tall and small herbs). Plots were sown in May 2002 and are since maintained by bi-annual weeding and mowing. Aboveground plant biomass was harvested twice in 2003 just prior to mowing (during peak standing biomass in early June and in late August) on all experimental plots of the monocultures. This was done by clipping the vegetation at 3 cm above ground in 2 rectangles of 0.2 x 0.5 m per plot. The location of these rectangles was assigned prior to each harvest by random selection of coordinates within the core area of the plots (i.e. excluding an outer edge of 0.5 m). The positions of the rectangles within plots were identical for all plots. The harvested biomass was sorted into categories: sown plant species, weed plant species (species not sown at the particular plot), and detached dead plant material (i.e., dead plant material in the data file). All biomass was dried to constant weight (70°C, >= 48 h) and weighed. The data for individual subsamples (i.e. rectangles) and the mean over samples for all biomass measures are given.

Aboveground plant biomass from the Jena Experiment (Monocultures, year 2010)

This data set contains aboveground plant biomass in 2010 (Sown plant community, Weed plant community, Dead plant material, and Unidentified plant material; all measured in biomass as dry weight) of the monoculture plots of a large grassland biodiversity experiment (the Jena Experiment). In the monoculture plots the biomass of the sown plant community contains only a single species per plot and this species is a different one for each plot. Which species has been sown in which plot is stated in the plot information table for monocultures (see further details below). The monoculture plots of 3.5 x 3.5 m were established for all of the 60 plant species of the Jena Experiment species pool with two replicates per species. One of the replicate plots per species was given up after the vegetation period of 2007 for all but the nine species belonging also to the so called dominance experiment in Jena. These nine species are: Alopecurus pratensis, Anthriscus sylvestris, Arrhenatherum elatius, Dactylis glomerata, Geranium pratense, Poa trivialis, Phleum pratense, Trifolium repens and Trifolium pratense.In 2010 plot size was reduced to 1 x 1 m. These 60 species comprising the species pool of the Jena Experiment belong to four functional groups (grasses, legumes, tall and small herbs). Plots were sown in May 2002 and are since maintained by bi-annual weeding and mowing. Aboveground plant biomass was harvested twice in 2010 just prior to mowing (during peak standing biomass in early June and in late August) on all experimental plots of the monocultures. This was done by clipping the vegetation at 3 cm above ground in 1 rectangle of 0.2 x 0.5 m per plot. The location of this rectangle was in the center of the plot area. The positions of the rectangles within plots were identical for all plots. The harvested biomass was sorted into categories: sown plant species, weed plant species (species not sown at the particular plot), detached dead plant material (i.e., dead plant material in the data file), and remaining plant material that could not be assigned to any category (i.e., unidentified plant material in the data file). All biomass was dried to constant weight (70°C, >= 48 h) and weighed.

Aboveground plant biomass from the Jena Experiment (Monocultures, year 2005)

This data set contains aboveground plant biomass in 2005 (Sown plant community, Weed plant community, Dead plant material, and Unidentified plant material; all measured in biomass as dry weight) of the monoculture plots of a large grassland biodiversity experiment (the Jena Experiment). In the monoculture plots the biomass of the sown plant community contains only a single species per plot and this species is a different one for each plot. Which species has been sown in which plot is stated in the plot information table for monocultures (see further details below). The monoculture plots of 3.5 x 3.5 m were established for all of the 60 plant species of the Jena Experiment species pool with two replicates per species. These 60 species comprising the species pool of the Jena Experiment belong to four functional groups (grasses, legumes, tall and small herbs). Plots were sown in May 2002 and are since maintained by bi-annual weeding and mowing. Aboveground plant biomass was harvested twice in 2005 just prior to mowing (during peak standing biomass in early June and in late August) on all experimental plots of the monocultures. This was done by clipping the vegetation at 3 cm above ground in 2 rectangles of 0.2 x 0.5 m per plot. The location of these rectangles was assigned prior to each harvest by random selection of coordinates within the core area of the plots (i.e. excluding an outer edge of 0.5 m). The positions of the rectangles within plots were identical for all plots. The harvested biomass was sorted into categories: sown plant species, weed plant species (species not sown at the particular plot), detached dead plant material (i.e., dead plant material in the data file), and remaining plant material that could not be assigned to any category (i.e., unidentified plant material in the data file). All biomass was dried to constant weight (70°C, >= 48 h) and weighed. The data for individual subsamples (i.e. rectangles) and the mean over samples for all biomass measures are given.

Aboveground plant biomass from the Jena Experiment (Monocultures, year 2006)

This data set contains aboveground plant biomass in 2006 (Sown plant community, Weed plant community, Dead plant material, and Unidentified plant material; all measured in biomass as dry weight) of the monoculture plots of a large grassland biodiversity experiment (the Jena Experiment). In the monoculture plots the biomass of the sown plant community contains only a single species per plot and this species is a different one for each plot. Which species has been sown in which plot is stated in the plot information table for monocultures (see further details below). The monoculture plots of 3.5 x 3.5 m were established for all of the 60 plant species of the Jena Experiment species pool with two replicates per species. These 60 species comprising the species pool of the Jena Experiment belong to four functional groups (grasses, legumes, tall and small herbs). Plots were sown in May 2002 and are since maintained by bi-annual weeding and mowing. Aboveground plant biomass was harvested twice in 2006 just prior to mowing (during peak standing biomass in early June and in late August) on all experimental plots of the monocultures. This was done by clipping the vegetation at 3 cm above ground in 2 rectangles of 0.2 x 0.5 m per plot. The location of these rectangles was assigned prior to each harvest by random selection of coordinates within the core area of the plots (i.e. excluding an outer edge of 0.5 m). The positions of the rectangles within plots were identical for all plots. The harvested biomass was sorted into categories: sown plant species, weed plant species (species not sown at the particular plot), detached dead plant material (i.e., dead plant material in the data file), and remaining plant material that could not be assigned to any category (i.e., unidentified plant material in the data file). All biomass was dried to constant weight (70°C, >= 48 h) and weighed. The data for individual subsamples (i.e. rectangles) and the mean over samples for all biomass measures are given.