A record of Probopyrus bithynis (Richardson, 1904) in Macrobrachium rosenbergii (De Man) from coastal Andhra Pradesh, India, with special reference to host-parasite relationship

An incidence of bopyrid isopod infestation was observed in giant freshwater prawn, Macrobrachium rosenbergii (de Man) juveniles (40-60 mm/0.9-1.5 g) in a scampi culture farm in East Godavari district of Andhra Pradesh. The presence of parasite was observed by conspicuous boil like swelling of the branchial chamber where the parasite was found lodged on the gills. The infested gill was highly compressed and necrosed. Only one branchial chamber was infested by the parasite while the other gill was normal. The infested prawns were thin and emaciated and showed retarded growth. The parasite was identified as Probopyrus bithynis (Richardson, 1904) which caused inhibition of ventilation due to its permanent lodging in the branchial chamber and impaired the gaseous exchange by gills. It was also observed that this parasite caused parasitic castration in the infested prawns.

Improving the performance of a valveless pulse combustor using unsteady fuel injection

This paper describes an experimental investigation into the effect of unsteady fuel injection on the performance of a valveless pulse combustor. Two fuel systems were used. The first delivered a steady flow of ethylene through choked nozzles, and the second delivered ethylene in discrete pulses using high-frequency fuel injectors. Both fuel systems injected directly into the combustion chamber. The high-frequency fuel injectors were phase locked to the unsteady pressure measured on the inlet pipe. The phase and opening pulse width of the injectors and the time-averaged fuel mass flow rate through the injectors were independently varied. For a given fuel mass flow rate, it is shown that the maximum pressure amplitude occurs when fuel is injected during flow reversal in the inlet pipe, i.e. flow direction is out of the combustor. The optimal fuel injection pulse width is shown to be approximately 2/9th of the cycle. It should, however, be noted that this is the shortest time in which the injectors can reliably be fully opened and closed. It is shown that by using unsteady fuel injection the mass flow rate of fuel needed to achieve a given amplitude of unsteady pressure can be reduced by up to 65% when compared with the steady fuel injection case. At low fuel mass flow rates unsteady fuel injection is shown to raise the efficiency of the combustor by a factor of 7 decreasing to a factor of 2 at high fuel mass flow rates. Copyright © 2008 by the American Institute of Aeronautics and Astronautics, Inc.

Investigation of the effect of combustor cooling geometry on acoustic energy absorption

To control combustion instabilities occurring in LPP gas turbine combustors, several active and passive systems have been developed in recent years. The combustion chamber cooling geometry has the potential to influence instability feedback loops by absorbing acoustical energy inside the combustor. The design of the cooling liner and the geometry of the cooling plenum and the cooling air flow rate have a significant influence on the absorption characteristics of the system. This paper presents the results of a cold flow study which was carried out in the course of a comprehensive study on the influence of the cooling geometry on combustor thermoacoustics. Absorption characteristics of three different cooling liner geometries and non-perforated plates were determined over a frequency range from 50 Hz to 600 Hz for different cooling flow rates and different cooling plenum volumes. The experimental results compared well with results from a low order thermoacoustic network model. The acoustic energy absorption spectrum of a cooling liner with 90°-hole configuration was found to be strongly dependent on cooling flow rate and cooling plenum volume, whereas the absorption spectrum of cooling liners with 25°-holes were found to be strongly dependent on the cooling plenum volume, but less dependent on the cooling air flow rate. All cooling liner setups with perforations were capable of increased acoustic absorption over a broad band of frequencies compared to the case of non-perforated combustor walls. © 2010 by Johannes Schmidt.

Boundary-layer suction system design for laminar-flying-wing aircraft

The present study aims to provide insight into the parameters affecting practical laminar-flow-control suction power requirements for a commercial laminar-flying-wing transport aircraft. It is shown that there is a minimum power requirement independent of the suction system design, associated with the stagnation pressure loss in the boundary layer. This requirement increases with aerofoil section thickness, but depends only weakly on Mach number and (for a thick, lightly loaded laminar flying wing) lift coefficient. Deviation from the optimal suction distribution, due to a practical chamber-based architecture, is found to have very little effect on the overall suction coefficient; hence, to a good approximation, the power penalty is given by the product of the optimal suction flow rate coefficient and the average skin pressure drop. In the spanwise direction, through suitable choice of chamber depth, the pressure drop due to frictional and inertial effects may be rendered negligible. Finally, if there are fewer pumps than chambers, the average pressure drop from the aerofoil surface to the pump collector ducts, rather than to the chambers, determines the power penalty. For the representative laminar-flying-wing aircraft parameters considered here, the minimum power associated with boundary-layer losses alone contributes some 80-90% of the total power requirement. © 2011 by the American Institute of Aeronautics and Astronautics, Inc.

Studies on smoke curing and preservation of oil sardine (Sardinella longiceps)

A method is reported for smoke curing of oil sardine (Sardinella longiceps) by dry salting in the ratio of 1:6 (salt to fish), followed by smoking in the traditional smoke chamber in two stages, (1) at 45°C for 3h hand (2) at 75°C for 2h with smoke generated from coconut husk, wood shavings and saw dust in 2:2:1 proportion. The product obtained had good odour, flavour, golden yellow colour and a shelf-life of 8 weeks at room temperature (26 to 28°C)

Effects of furanace on Brachionus

Tiger prawn P.monodon) larvae utilize Brachionus a rotifer, as food in the Zoea 3 and mysis stages when they change from an herbivorous to an omnivorous diet. The present work aims to show the effects of furanace on the population growth of Brachionus. Cultures of Brachionus were obtained and fed with Chlorella at a density of 1-2x10 SUP-6 cells/ml. Five liters of the culture water were placed in each of 4 white, circular, 152x304 mm plastic basins. The mean initial densities of the rotifer ranged from 26 . 5 to 38 . 5 individuals/ml. The concentrations of furanace were 0, 1, 2 and 3 mg /l. The cultures were vigorously aerated. Population growth was observed after 3, 6, and 9 hours of exposure. The cultures were thoroughly mixed before samples were taken to ensure an almost equal distribution of the rotifers in the water. To facilitate the counting of the rotifer, one drop of Lugol's solution was added to each sample. This immobilizes the rotifer as well as stops further reproduction. Individuals with only the lorica left or with badly deformed lorica were considered dead. Population counts were done using a Sedgwick-Rafter counting chamber. Among the different durations of exposure, the percentage survival of the populations in the furanace baths were highest after 3 hr. There were slight increases in the control and 2 mg/l and slight decreases in 1 and 3 mg/l. The differences in the mean densities are statistically insignificant at . 01 significance level. After a 6-hr exposure, the control population reached its peak density with a survival of 89%. Populations in furanace baths decreased to 88 . 5% in both 2 and 3 mg /l followed closely by 87% in 1 mg/l. Again, no statistical differences exist among all the levels. The mean percentage survival in 1 and 2 mg/l increased (89% and 91%, respectively) after a 9-hr expsoure, while those in the control and 3 mg/l decreased to 86 . 5% and 88 . 25%, respectively. There were no marked differences in appearance noted among the individuals in furanace baths and those in the control.

Preparation and keeping quality of hot smoked mackerel

A method has been standardised for the production of smoke cured mackerel by dry salting in the ratio of 1:8 salt to fish followed by smoking in a traditional smoke chamber at 70±5°C for 5h. The smoke was generated by burning moist coconut husk and saw dust. The product obtained by this method had shelf-lives of 105, 95 and 6 days in chilled storage (0 to 2°C) refrigerated storage (10±2°C) and at room temperature (29±2°C) respectively.

Effects of unconditioned and conditioned aversive stimuli in an intense fear conditioning paradigm on synaptic plasticity in the hippocampal CA1 area in vivo

Repeated vivid recalls or flashbacks of traumatic memories and memory deficits are the cardinal features of post-traumatic stress disorder (PTSD). The underlying mechanisms are not fully understood yet. Here, we examined the effects of very strong fear conditioning (20 pairings of a light with a 1.5-mA, 0.5-s foot shock) and subsequent reexposure to the conditioning context (chamber A), a similar context (chamber B), and/or to the fear conditioned stimulus (CS) (a light) on synaptic plasticity in the hippocampal CA1 area in anesthetized Sprague-Dawley rats. The conditioning procedure resulted in very strong conditioned fear, as reflected by high levels of persistent freezing, to both the contexts and to the CS, 24 h after fear conditioning. The induction of long-term potentiation ON was blocked immediately after fear conditioning. It was still markedly impaired 24 h after fear conditioning; reexposure to the conditioning chamber A (CA) or to a similar chamber 13 (CB) did not affect the impairment. However, presentation of the CS in the CA exacerbated the impairment of LTP, whereas the CS presentation in a CB ameliorated the impairment so that LTP induction did not differ from that of control groups. The induction of long-term depression (LTD) was facilitated immediately, but not 24 h, after fear conditioning. Only reexposure to the CS in the CA, but not reexposure to either chamber A or B alone, or the CS in chamber B, 24 h after conditioning, reinstated the facilitation of LTD induction. These data demonstrate that unconditioned and conditioned aversive stimuli in an intense fear conditioning paradigm can have profound effects on hippocampal synaptic plasticity, which may aid to understand the mechanisms underlying impairments of hippocampus-dependent memory by stress or in PTSD. (c) 2005 Wiley-Liss, Inc.

The nonlinear heat release response of stratified lean-premixed flames to acoustic velocity oscillations

This paper analyzes the forced response of swirl-stabilized lean-premixed flames to high-amplitude acoustic forcing in a laboratory-scale stratified burner operated with CH4 and air at atmospheric pressure. The double-swirler, double-channel annular burner was specially designed to generate high-amplitude acoustic velocity oscillations and a radial equivalence ratio gradient at the inlet of the combustion chamber. Temporal oscillations of equivalence ratio along the axial direction are dissipated over a long distance, and therefore the effects of time-varying fuel/air ratio on the response are not considered in the present investigation. Simultaneous measurements of inlet velocity and heat release rate oscillations were made using a constant temperature anemometer and photomultiplier tubes with narrow-band OH*/CH* interference filters. Time-averaged and phase-synchronized CH* chemiluminescence intensities were measured using an intensified CCD camera. The measurements show that flame stabilization mechanisms vary depending on equivalence ratio gradients for a constant global equivalence ratio (φg=0.60). Under uniformly premixed conditions, an enveloped M-shaped flame is observed. In contrast, under stratified conditions, a dihedral V-flame and a toroidal detached flame develop in the outer stream and inner stream fuel enrichment cases, respectively. The modification of the stabilization mechanism has a significant impact on the nonlinear response of stratified flames to high-amplitude acoustic forcing (u'/U∼0.45 and f=60, 160Hz). Outer stream enrichment tends to improve the flame's stiffness with respect to incident acoustic/vortical disturbances, whereas inner stream stratification tends to enhance the nonlinear flame dynamics, as manifested by the complex interaction between the swirl flame and large-scale coherent vortices with different length scales and shedding points. It was found that the behavior of the measured flame describing functions (FDF), which depend on radial fuel stratification, are well correlated with previous measurements of the intensity of self-excited combustion instabilities in the stratified swirl burner. The results presented in this paper provide insight into the impact of nonuniform reactant stoichiometry on combustion instabilities, its effect on flame location and the interaction with unsteady flow structures. © 2011 The Combustion Institute.

Measurement of liquid film thickness by optical fluorescence and its application to an oscillating piston positive displacement flowmeter

The movement of the circular piston in an oscillating piston positive displacement flowmeter is important in understanding the operation of the flowmeter, and the leakage of liquid past the piston plays a key role in the performance of the meter. The clearances between the piston and the chamber are small, typically less than 60 νm. In order to measure this film thickness a fluorescent dye was added to the water passing through the meter, which was illuminated with UV light. Visible light images were captured with a digital camera and analysed to give a measure of the film thickness with an uncertainty of less than 7%. It is known that this method lacks precision unless careful calibration is undertaken. Methods to achieve this are discussed in the paper. The grey level values for a range of film thicknesses were calibrated in situ with six dye concentrations to select the most appropriate one for the range of liquid film thickness. Data obtained for the oscillating piston flowmeter demonstrate the value of the fluorescence technique. The method is useful, inexpensive and straightforward and can be extended to other applications where measurement of liquid film thickness is required. © 2011 IOP Publishing Ltd.

Passive control of combustion instability in a low emissions aeroderivative gas turbine

This paper describes the conceptual ideas, the theoretical validation, the laboratory testing and the field trials of a recently patented fuel-air mixing device for use in high-pressure ratio, low emissions, gaseous-fueled gas turbines. By making the fuel-air mixing process insensitive to pressure fluctuations in the combustion chamber, it is possible to avoid the common problem of positive feedback between mixture strength and the unsteady combustion process. More specifically, a mixing duct has been designed such that fuel-air ratio fluctuations over a wide range of frequencies can be damped out by passive design means. By scaling the design in such a way that the range of damped frequencies covers the frequency spectrum of the acoustic modes in the combustor, the instability mechanism can be removed. After systematic development, this design philosophy was successfully applied to a 35:1 pressure ratio aeroderivative gas turbine yielding very low noise levels and very competitive NOx and CO measurements. The development of the new premixer is described from conceptual origins through analytic and CFD evaluation to laboratory testing and final field trials. Also included in this paper are comments about the practical issues of mixing, flashback resistance and autoignition.

DDES of a supersonic coaxial helium jet

The mixing of a light gas in a scramjet combustion chamber is replicated through the simulation of a supersonic coaxial helium jet. Sensitivities of the RANS method to model constants is presented and the DDES method is employed to try and alleviate this modelling weakness. A significant delay in the shear layer transition is found to occur in the DDES simulation and it is suggested this may be due to the absence of inlet turbulence. The influence of the introduction of inflow turbulence is investigated and computational results are compared to experimental data. The influence of model constants on the DDES results are presented. © 2012 by Peter Cocks.

Simulations of the SCHOLAR scramjet experiment

The DDES method is employed to investigate the complex physics involved in supersonic combustion and in particular in the SCHOLAR scramjet test case. The influence on computational results of prescribing turbulent fluctuations at the entrance to the combustion chamber is investigated. The interaction of shock waves, vortices, turbulence and combustion is studied and the existence of secondary vortices on the upper will of the combustor is proposed. © 2012 by Peter Cocks.

Effects of nonuniform reactant stoichiometry on combustion instability

This paper analyzes the forced response of swirl-stabilized lean-premixed flames to acoustic forcing in a laboratory-scale stratified burner. The double-swirler, double-channel annular burner was specially designed to generate acoustic velocity oscillations and radial fuel stratification at the inlet of the combustion chamber. Temporal oscillations of equivalence ratio along the axial direction are dissipated over a long distance, and therefore the effects of time-varying fuel/air ratio on the flame response are not considered. Simultaneous measurements of inlet velocity and heat release rate oscillations were made using a hot wire anemometer and photomultiplier tubes with narrowband OH*/CH* interference filters. Time-averaged CH* chemiluminescence intensities were measured using an intensified CCD camera. Results show that flame stabilization mechanisms vary depending on stratification ratio for a constant global equivalence ratio. For a uniformly premixed condition, an enveloped M-shaped flame is observed. For stratified conditions, however, a dihedral V-flame and a detached flame are developed for outer stream and inner stream fuel enrichment cases, respectively. Flame transfer function (FTF) measurement results indicate that a V-shaped flame tends to damp incident flow oscillations, while a detached flame acts as a strong amplifier relative to the uniformly premixed condition. The phase difference of FTF increases in the presence of stratification. More importantly, the dynamic characteristics obtained from the forced stratified flame measurements are well correlated with unsteady flame behavior under limit-cycle pressure oscillations. The results presented in this paper provide insight into the impact of nonuniform reactant stoichiometry on combustion instabilities, which has not been well explored to date. Copyright © 2011 by ASME.

Influence of micro supersonic jets on micro percussion drilling of 316L stainless steel using nanosecond 355NM laser radiation

The interaction phenomena of nanosecond Q-switched diode-pumped solid state (DPSS) laser using 355nm radiation with 0.2mm thick 316L stainless steel foil was investigated at incident laser fluence range of 19 - 82Jcm-2. The characterization study was performed with and without the use of assist gas by utilizing micro supersonic minimum length nozzles (MLN), specifically designed for air at inlet chamber pressure of 8bar. MLN ranged in throat diameters of 200μm, 300μm, and 500μm respectively. Average etch rate per pulse under the influence of three micro supersonic impinging jets, for both oxygen and air showed the average etch rate was reduced when high-speed gas jets were utilized, compared to that without any gas jets, but significant variation was noticed between different jet sizes. Highest etch rate and quality was achieved with the smallest diameter nozzle, suggesting that micro nozzles can produce a viable process route for micro laser cutting.