Environmental impact assessment of agrochemicals for fish production - a review paper

The environmental impact of agro-chemicals for fish production was extensively reviewed. The positive contribution of agro- chemicals and the devastating effect on aquaculture was x-rayed to alert users to this obvious environmental problem. Lime and fertilizers are commonly used in fish farming to increase pH of pond soil and water and to increase alkalinity and hardness, reduce humic acid content and to initiate primary and secondary productivity. Devastating effect of lime on environment is likely to be minimal. In the case of fertilizers, over utilization of this agro-chemical could impair water quality as phytoplankton bloom become excessive which consequently raises BOD. The use of Therapeutants in aquaculture was discovered to be more popular in Europe and North America than in the tropics (Africa). Commonly used therapeutants include antibiotics and antimicrobials. For fish pathology chemicals like formalin, potassium permanganate, Dipterex and malachite green are widely in use. Effluent from farms where these chemicals are commonly in use can distort the aquatic ecosystem. The changes in water quality, aquatic community structure and productivity caused by intensive aquaculture are typical of the impacts of pollution from a wide variety of sources like sewage, agricultural run-off and effluent discharges from industry

The effects of pollution on phytoplankton in a stretch of River Kubanni, Zaria, Nigeria

River Kubanni, a major tributary of River Galma, receives both organic and inorganic wastes through run-offs and seepage from residential and agricultural areas of Tundun-Wada, Zaria. Water and phytoplankton samples were collected once a month from three stations on a stretch of the river, for eight months (February, 1994-0ctober, 1994). The physico-chemical parameters and phytoplankton composition were determined and correlated to one another. The distribution and composition of phytoplankton species are affected by variations through fluctuations in environmental variables such as temperature, velocity, transparency, pH, dissolved Oxygen, total alkalinity, total hardness, electrical conductivity and total dissolved matter. Highest dissolved oxygen concentration in February coincided with the minimum water temperature due to the cool harmattan winds. Low alkalinity resulted in low phytoplankton productivity while a rise in total dissolved matter resulted in increase in electrical conductivity and high phytoplankton productivity. The presence of Oscillatoria sp and Euglena sp in station 2 and 3 are indicative of organic pollution in these stations. However, the river stretch is suitable for fish production with respect to water hardness and pH

A Mechanical Model For The Quantification Of The Effect Of Laser Quenching On Ctod In Steels

The technology of laser quenching is widely used to improve the surface properties of steels in surface engineering. Generally, laser quenching of steels can lead to two important results. One is the generation of residual stress in the surface layer. In general, the residual stress varies from the surface to the interior along the quenched track depth direction, and the residual stress variation is termed as residual stress gradient effect in this work. The other is the change of mechanical properties of the surface layer, such as the increases of the micro-hardness, resulting from the changes of the microstructure of the surface layer. In this work, a mechanical model of a laser-quenched specimen with a crack in the middle of the quenched layer is developed to quantify the effect of residual stress gradient and the average micro-hardness over the crack length on crack tip opening displacement (CTOD). It is assumed that the crack in the middle of the quenched layer is created after laser quenching, and the crack can be a pre-crack or a defect due to some reasons, such as a void, cavity or a micro-crack. Based on the elastic-plastic fracture mechanics theory and using the relationship between the micro-hardness and yield strength, a concise analytical solution, which can be used to quantify the effect of residual stress gradient and the average micro-hardness over the crack length resulting from laser quenching on CTOD, is obtained. The concise analytical solution obtained in this work, cannot only be used as a means to predict the crack driving force in terms of the CTOD, but also serve as a baseline for further experimental investigation of the effect after laser-quenching treatment on fracture toughness in terms of the critical CTOD of a specimen, accounting for the laser-quenching effect. A numerical example presented in this work shows that the CTOD of the quenched can be significantly decreased in comparison with that of the unquenched. (C) 2008 Elsevier B.V. All rights reserved.

Influences Of Precursor Constitution And Processing Speed On Microstructure And Wear Behavior During Laser Clad Composite Coatings On Gamma-Tial Intermetallic Alloy

The effects of constitution of precursor mixed powders and scan speed on microstructure and wear properties were designed and investigated during laser clad gamma/Cr7C3/TiC composite coatings on gamma-TiAl intermetallic alloy substrates with NiCr-Cr3C2 precursor mixed powders. The results indicate that both the constitution of the precursor mixed powders and the beam scan rate have remarkable influence on microstructure and attendant hardness as well as wear resistance of the formed composite coatings. The wear mechanisms of the original TiAl alloy and laser clad composite coatings were investigated. The composite coating with an optimum compromise between constitution of NiCr-Cr3C2 precursor mixed powders as well as being processed under moderate scan speed exhibits the best wear resistance under dry sliding wear test conditions. (C) 2008 Elsevier Ltd. All rights reserved.

Laser Guiding in the Randomicity of Discrete Surface Strengthening by Arc Discharge

Several discharge areas by laser-guided discharge (LGD) were compared with those by common arc discharge. The randomicity of discharge areas by common arc discharge was controlled by laser guiding on two scales: large scale (the spacing of the discharge areas) and small scale (the inside of the discharge area). The position of the discharge area overlapped completely with a laser focus; therefore, the distribution and surface shape of the discharge areas were controlled. The stochastic movement of anode spot in the discharge area was controlled by laser guiding. As such, the repetitive melting and solidifying of microstructures in the discharge area was constrained. The tempered microstruc- tures in the discharge area were voided, the utilization efficiency of input energy was improved, and the strengthened depth of the discharge areas was increased. The regularity of cross-sectional shape of the discharge area was also improved. The hardness of microstructures in both discharge areas is greater than that of the base material. The highest level of hardness of microstructures in both discharge areas measures above 1000 HV. In summary, the hardness ofmicrostructures in the discharge area by LGD is larger and more discrete than that by common arc discharge.

A small arc-heated plasma testing facility for thermal protection materials

Experimental research on a 150 kW arc-heated plasma testing facility was conducted. Stable plasma jets with different gas compositions, temperatures and velocities were obtained at chamber pressure between 400 Pa – 100 kPa. Stagnation ablation experiments were conducted on samples of typical super alloys used for thermal protection systems. The microstructure and hardness of alloys before and after ablation were compared.

Study of the origins of toughness in amorphous metals

Amorphous metals that form fully glassy parts over a few millimeters in thickness are still relatively new materials. Their glassy structure gives them particularly high strengths, high yield strains, high hardness values, high resilience, and low damping losses, but this can also result in an extremely low tolerance to the presence of flaws in the material. Since this glassy structure lacks the ordered crystal structure, it also lacks the crystalline defect (dislocations) that provides the micromechanism of toughening and flaw insensitivity in conventional metals. Without a sufficient and reliable toughness that results in a large tolerance of damage in the material, metallic glasses will struggle to be adopted commercially. Here, we identify the origin of toughness in metallic glass as the competition between the intrinsic toughening mechanism of shear banding ahead of a crack and crack propagation by the cavitation of the liquid inside the shear bands. We present a detailed study over the first three chapters mainly focusing on the process of shear banding; its crucial role in giving rise to one of the most damage-tolerant materials known, its extreme sensitivity to the configurational state of a glass with moderate toughness, and how the configurational state can be changed with the addition of minor elements. The last chapter is a novel investigation into the cavitation barrier in glass-forming liquids, the competing process to shear banding. The combination of our results represents an increased understanding of the major influences on the fracture toughness of metallic glasses and thus provides a path for the improvement and development of tougher metallic glasses.

Determination and modelling of water quality parameter in Abuja metropolis

This research work involves the determination and modelling of water parameter such as pH, temperature, turbidity, chloride, hardness. The result of the analysis was used as important operating variables to generate a model equation of pH, hardness, temperature, turbidity and chloride. The values obtained from the model equation were compared with those from experiment. On an average bases the values were close. These parameters can be used to monitor the extent of pollution of pond water and to monitor stress and diseases of fish. The experimental data of pH was in the range of 6.7 to 6.9 while the modelled result was also between 6.7 to 7.0. The turbidity experimental value was close to the modelled value also. The chloride value for the experimental data was in the range of 25.32 to 35.0. The total hardness value ranges between 4.5 to 65.1 mg/l while the modelled result ranges between 11.025 to 68.402 mg/l. The result was within the acceptable limit of world health organization standard on water quality parameter.

Some aspects of the limnology of Makwaye (Ahmadu Bello University) Lake, Samaru, Zaria

The monthly variations in the physico-chemical parameters and zooplankton abundance were followed from December, 2003 to March 2004 in Makwaye (Ahmadu Bello University Farm) Lake, Samaru, Zaria. In this lake, all physico-chemical parameters investigated showed wide variations within the months except hardness, which exhibited highly significant variation both between stations and within months. Chemical variables including Na, Mg, Zn, Pb, Fe, K and Cu showed significant variations within the months. Three groups namely Cladocera (32.62%), Rotifera (29.33%) and Copepoda (38.05%) were observed. These indicated low species richness

Development of selection methods for steels and their heat treatments

Designers who want to manufacture a hardenable steel component need to select both the steel and its heat treatment. This project aims to develop a selection methodology for steels and process routes as an aid to designers. Three studies were conducted: - production of software to calculate the "equivalent diameter" and "equivalent Jominy distance" for simple shapes of a steel component; - prediction of semi-empirical Jominy curves (as-cooled) using CCT diagrams and process modelling methods, which were validated by experiment on plain carbon steels; - investigation of tempering of Jominy bars to explore the potential for semi-empirical models for the hardness after tempering.

Developing and characterizing bulk metallic glasses for extreme applications

Metallic glasses have typically been treated as a “one size fits all” type of material. Every alloy is considered to have high strength, high hardness, large elastic limits, corrosion resistance, etc. However, similar to traditional crystalline materials, properties are strongly dependent upon the constituent elements, how it was processed, and the conditions under which it will be used. An important distinction which can be made is between metallic glasses and their composites. Charpy impact toughness measurements are performed to determine the effect processing and microstructure have on bulk metallic glass matrix composites (BMGMCs). Samples are suction cast, machined from commercial plates, and semi-solidly forged (SSF). The SSF specimens have been found to have the highest impact toughness due to the coarsening of the dendrites, which occurs during the semi-solid processing stages. Ductile to brittle transition (DTBT) temperatures are measured for a BMGMC. While at room temperature the BMGMC is highly toughened compared to a fully glassy alloy, it undergoes a DTBT by 250 K. At this point, its impact toughness mirrors that of the constituent glassy matrix. In the following chapter, BMGMCs are shown to have the capability of being capacitively welded to form single, monolithic structures. Shear measurements are performed across welded samples, and, at sufficient weld energies, are found to retain the strength of the parent alloy. Cross-sections are inspected via SEM and no visible crystallization of the matrix occurs.

Next, metallic glasses and BMGMCs are formed into sheets and eggbox structures are tested in hypervelocity impacts. Metallic glasses are ideal candidates for protection against micrometeorite orbital debris due to their high hardness and relatively low density. A flat single layer, flat BMG is compared to a BMGMC eggbox and the latter creates a more diffuse projectile cloud after penetration. A three tiered eggbox structure is also tested by firing a 3.17 mm aluminum sphere at 2.7 km/s at it. The projectile penetrates the first two layers, but is successfully contained by the third.

A large series of metallic glass alloys are created and their wear loss is measured in a pin on disk test. Wear is found to vary dramatically among different metallic glasses, with some considerably outperforming the current state-of-the-art crystalline material (most notably Cu₄₃Zr₄₃Al₇Be₇). Others, on the other hand, suffered extensive wear loss. Commercially available Vitreloy 1 lost nearly three times as much mass in wear as alloy prepared in a laboratory setting. No conclusive correlations can be found between any set of mechanical properties (hardness, density, elastic, bulk, or shear modulus, Poisson’s ratio, frictional force, and run in time) and wear loss. Heat treatments are performed on Vitreloy 1 and Cu₄₃Zr₄₃Al₇Be₇. Anneals near the glass transition temperature are found to increase hardness slightly, but decrease wear loss significantly. Crystallization of both alloys leads to dramatic increases in wear resistance. Finally, wear tests under vacuum are performed on the two alloys above. Vitreloy 1 experiences a dramatic decrease in wear loss, while Cu₄₃Zr₄₃Al₇Be₇ has a moderate increase. Meanwhile, gears are fabricated through three techniques: electrical discharge machining of 1 cm by 3 mm cylinders, semisolid forging, and copper mold suction casting. Initial testing finds the pin on disk test to be an accurate predictor of wear performance in gears.

The final chapter explores an exciting technique in the field of additive manufacturing. Laser engineered net shaping (LENS) is a method whereby small amounts of metallic powders are melted by a laser such that shapes and designs can be built layer by layer into a final part. The technique is extended to mixing different powders during melting, so that compositional gradients can be created across a manufactured part. Two compositional gradients are fabricated and characterized. Ti 6Al¬ 4V to pure vanadium was chosen for its combination of high strength and light weight on one end, and high melting point on the other. It was inspected by cross-sectional x-ray diffraction, and only the anticipated phases were present. 304L stainless steel to Invar 36 was created in both pillar and as a radial gradient. It combines strength and weldability along with a zero coefficient of thermal expansion material. Only the austenite phase is found to be present via x-ray diffraction. Coefficient of thermal expansion is measured for four compositions, and it is found to be tunable depending on composition.

Fabricación de Blisks aeronáuticos mediante electroerosión (EDM)

[ES]En el mundo de la aeronáutica cada vez más se utilizan materiales de alta dureza y baja maquinabilidad. Por ello la necesidad de utilización de métodos de fabricación no convencionales de mecanizado. Para la fabricación de los Blisks, la electroerosión resulta un proceso ventajoso frente a otros procesos. En este trabajo se va llevar a cabo las etapas de puesta a punto de utillajes, mecanizado y control dimensional de los álabes mecanizados.

Avaliação da influência de diferentes óleos extensores com baixo teor de policíclicos aromáticos nas propriedades da borracha à base butadieno e estireno (SBR)

O óleo extensor normalmente empregado em copolímeros à base de butadieno e estireno ( borracha SBR) da série 1712 é o extrato aromático (DAE). Nesta Dissertação, esse óleo foi substituído por óleos com baixos teores de policíclicos aromáticos em formulações de SBR. Esta substituição se deu em atendimento a Regulamentação REACH (EC No1907/2006 do Parlamento Europeu e do Conselho de 18 de Dezembro de 2006, Anexo XVII) que determina que a soma de hidrocarbonetos policíclicos aromáticos individuais (PAHs) deve ser abaixo de 10 mg/kg e o teor de benzo(a)pireno (BaP) não deve exceder 1 mg/kg. Os óleos empregados foram o extrato aromático residual tratado (TRAE) e dois óleos naftênicos de fornecedores diferentes (HN1 e HN2). As composições de SBR estendidas em DAE, TRAE, HN1 e HN2 tiveram suas propriedades térmicas avaliadas por análise termogravimétrica (TG) e calorimetria diferencial de varredura (DSC). As propriedades físicas foram determinadas por ensaios de tração, dureza, resistência à abrasão e resiliência. Foram ainda avaliadas as propriedades reométricas e reológicas, por viscosidade e relaxação Mooney, respectivamente. Ao final os resultados demonstraram que é possível a substituição do óleo extensor por quaisquer dos óleos testados sem prejuízos nas propriedades estudadas

Caracterização metalúrgica de juntas de aço inoxidável superduplex soldadas por processo TIG autógeno

Os aços inoxidáveis do tipo duplex possuem grande importância na indústria, principalmente na do petróleo e gás natural, por apresentarem elevada resistência mecânica e excelente resistência à corrosão. Caracterizam-se por apresentar estrutura bifásica, constituída de proporções praticamente iguais de ferrita e austenita. O presente trabalho caracterizou juntas soldadas por TIG autógeno de aço inoxidável duplex UNS S32760. Foram confeccionados quatro grupos de amostras, provenientes da variação da corrente de soldagem e consequentemente do aporte térmico (corrente de pico: 25A e 40A - aporte térmico: 0,12KJ/mm e 0,19KJ/mm) e da composição do gás de proteção (argônio puro ou argônio contendo 2,5% nitrogênio). Foram utilizadas técnicas de caracterização por metalografia colorida, análise e processamento digital de imagens, ensaios de microdureza Vickers. Para avaliar a resistência à corrosão foram realizados ensaios de potencial em circuito aberto com solução de cloreto férrico (FeCl3) e eletrodo de referência de calomelano saturado. A análise quantitativa das fases ferrita e austenita presentes nas juntas soldadas mostrou que a adição de nitrogênio no gás de proteção favoreceu a formação da fase austenita, variando de 11% (sem nitrogênio) para 26% (com nitrogênio) a quantidade desta fase. Em uma análise qualitativa a variação do aporte térmico: 0,12KJ/mm para 0,19KJ/mm resultou no aumento do tamanho de grãos da fase ferrita.

The growth of brown trout

An article discussing the factors affecting the rate of growth of brown trout, detailing the research udnertaken at Wray Castle, designed to clarify the influencing factors in different waters and investigate what would be required to increase their size. The article considers factors such as alkalinity, total hardness, the presence of coarse fish in the waterbodies and competition for food. Previous work undertaken on brown trout in Ireland by other authors is reviewed. A figure showing average growth rate of brown trout in five lakes, as determined from their scales (Lough Derg, Windermere, Loch Leven, Ullswater, Haweswater).