The spalling of concrete in fires

The occurrence of spalling is a major factor in determining the fire resistance of concrete constructions. The apparently random occurrence of spalling has limited the development and application of fire resistance modelling for concrete structures. This Thesis describes an experimental investigation into the spalling of concrete on exposure to elevated temperatures. It has been shown that spalling may be categorised into four distinct types, aggregate spalling, corner spalling, surface spalling and explosive spalling. Aggregate spalling has been found to be a form of shear failure of aggregates local to the heated surface. The susceptibility of any particular concrete to aggregate spalling can be quantified from parameters which include the coefficients of thermal expansion of both the aggregate and the surrounding mortar, the size and thermal diffusivity of the aggregate and the rate of heating. Corner spalling, which is particularly significant for the fire resistance of concrete columns, is a result of concrete losing its tensile strength at elevated temperatures. Surface spalling is the result of excessive pore pressures within heated concrete. An empirical model has been developed to allow quantification of the pore pressures and a material failure model proposed. The dominant parameters are rate of heating, pore saturation and concrete permeability. Surface spalling may be alleviated by limiting pore pressure development and a number of methods to this end have been evaluated. Explosive spalling involves the catastrophic failure of a concrete element and may be caused by either of two distinct mechanisms. In the first instance, excessive pore pressures can cause explosive spalling, although the effect is limited principally to unloaded or relatively small specimens. A second cause of explosive spalling is where the superimposition of thermally induced stresses on applied load stresses exceed the concrete's strength.

The mechanical properties and formability of dual-phase steel

In recent years dual phase steels comprising of 5-20% martensite in a ferrite matrix have come into the limelight of high strength cold formable steels because of their potential for vehicle weight saving. They show the following features: no yield point; relatively low initial flow stress; high initial workhardening rate; well sustained work hardening. As a consequence of these characteristics, dual phase steels exhibit a better combination of strength and elongation than other HSLA steels. In this thesis, a broad view of the factors which influence their properties is presented. Mechanical properties and forming ability of a commercially available dual phase steel and an AL-Si killed steel processed to dual phase form are investigated to ascertain the effect of their microstructure on their properties. It is found that the yield phenomena are masked by the transformation induced stresses present during processing and so yield point could be recovered under suitable ageing treatment; that apart from giving the above properties dual phasing gives rise to very low strain-rate sensitivity and a low R value ~ 1; that the mechanical response under rolling conditions is not different from those under tension; that there is a danger of damage to tooling during forming operations of these steels if fracture should precede instability as a result of grain size dependent strength found for these steels. It is also found that very little deformation of the martensite islands took place during deformation except at high strains. The work-hardening and the strength levels can be controlled by either decreasing the grain size or increasing the martensite volume fraction, but it is found that increasing martensite has a detrimental effect on ductility and the ductility and fracture strength can be controlled better by refining the grain size. A remarkable effect found in the dual phase steel tested is that the compressive strength is higher than the tensile strength. The reason for this observation is not yet clear but it is suggested that it might be due to the introduction of emissary type dislocations into the ferrite lattice as a result of twins formed in the martensite during transformation from austenite. The twins are envisaged to be {111} <112> in character.

Development of surface flaw thresholds for pre-cured fiber reinforced polymer and groove size tolerance for near surface mounted fiber reinforced polymer retrofit systems

Since the introduction of fiber reinforced polymers (FRP) for the repair and retrofit of concrete structures in the 1980’s, considerable research has been devoted to the feasibility of their application and predictive modeling of their performance. However, the effects of flaws present in the constitutive components and the practices in substrate preparation and treatment have not yet been thoroughly studied. This research aims at investigating the effect of surface preparation and treatment for the pre-cured FRP systems and the groove size tolerance for near surface mounted (NSM) FRP systems; and to set thresholds for guaranteed system performance. This study was conducted as part of the National Cooperative Highway Research Program (NCHRP) Project 10-59B to develop construction specifications and process control manual for repair and retrofit of concrete structures using bonded FRP systems. The research included both analytical and experimental components. The experimental program for the pre-cured FRP systems consisted of a total of twenty-four (24) reinforced concrete (RC) T-beams with various surface preparation parameters and surface flaws, including roughness, flatness, voids and cracks (cuts). For the NSM FRP systems, a total of twelve (12) additional RC T-beams were tested with different grooves sizes for FRP bars and strips. The analytical program included developing an elaborate nonlinear finite element model using the general purpose software ANSYS. The bond interface between FRP and concrete was modeled by a series of nonlinear springs. The model was validated against test data from the present study as well as those available from the literature. The model was subsequently used to extend the experimental range of parameters for surface flatness in pre-cured FRP systems and for groove size study in the NSM FRP systems. Test results, confirmed by further analyses, indicated that contrary to the general belief in the industry, the impact of surface roughness on the global performance of pre-cured FRP systems was negligible. The study also verified that threshold limits set for wet lay-up FRP systems can be extended to pre-cured systems. The study showed that larger surface voids and cracks (cuts) can adversely impact both the strength and ductility of pre-cured FRP systems. On the other hand, frequency (or spacing) of surface cracks (cuts) may only affect system ductility rather than its strength. Finally, within the range studied, groove size tolerance of ±1/8 in. does not appear to have an adverse effect on the performance of NSM FRP systems.

Seismic performance of hybrid fiber reinforced polymer-concrete pier frame systems

As an alternative to transverse spiral or hoop steel reinforcement, fiber reinforced polymers (FRPs) were introduced to the construction industry in the 1980’s. The concept of concrete-filled FRP tube (CFFT) has raised great interest amongst researchers in the last decade. FRP tube can act as a pour form, protective jacket, and shear and flexural reinforcement for concrete. However, seismic performance of CFFT bridge substructure has not yet been fully investigated. Experimental work in this study included four two-column bent tests, several component tests and coupon tests. Four 1/6-scale bridge pier frames, consisting of a control reinforced concrete frame (RCF), glass FRP-concrete frame (GFF), carbon FRP-concrete frame (CFF), and hybrid glass/carbon FRP-concrete frame (HFF) were tested under reverse cyclic lateral loading with constant axial loads. Specimen GFF did not show any sign of cracking at a drift ratio as high as 15% with considerable loading capacity, whereas Specimen CFF showed that lowest ductility with similar load capacity as in Specimen GFF. FRP-concrete columns and pier cap beams were then cut from the pier frame specimens, and were tested again in three point flexure under monotonic loading with no axial load. The tests indicated that bonding between FRP and concrete and yielding of steel both affect the flexural strength and ductility of the components. The coupon tests were carried out to establish the tensile strength and elastic modulus of each FRP tube and the FRP mold for the pier cap beam in the two principle directions of loading. A nonlinear analytical model was developed to predict the load-deflection responses of the pier frames. The model was validated against test results. Subsequently, a parametric study was conducted with variables such as frame height to span ratio, steel reinforcement ratio, FRP tube thickness, axial force, and compressive strength of concrete. A typical bridge was also simulated under three different ground acceleration records and damping ratios. Based on the analytical damage index, the RCF bridge was most severely damaged, whereas the GFF bridge only suffered minor repairable damages. Damping ratio was shown to have a pronounced effect on FRP-concrete bridges, just the same as in conventional bridges. This research was part of a multi-university project, which is founded by the National Science Foundation (NSF) - Network for Earthquake Engineering Simulation Research (NEESR) program.

Dynamic Behavior and Fatigue Life of Highway Bridges Due to Doubling Heavy Vehicles

An increase in the demand for the freight shipping in the United States has been predicted for the near future and Longer Combination Vehicles (LCVs), which can carry more loads in each trip, seem like a good solution for the problem. Currently, utilizing LCVs is not permitted in most states of the US and little research has been conducted on the effects of these heavy vehicles on the roads and bridges. In this research, efforts are made to study these effects by comparing the dynamic and fatigue effects of LCVs with more common trucks. Ten Steel and prestressed concrete bridges with span lengths ranging from 30’ to 140’ are designed and modeled using the grid system in MATLAB. Additionally, three more real bridges including two single span simply supported steel bridges and a three span continuous steel bridge are modeled using the same MATLAB code. The equations of motion of three LCVs as well as eight other trucks are derived and these vehicles are subjected to different road surface conditions and bumps on the roads and the designed and real bridges. By forming the bridge equations of motion using the mass, stiffness and damping matrices and considering the interaction between the truck and the bridge, the differential equations are solved using the ODE solver in MATLAB and the results of the forces in tires as well as the deflections and moments in the bridge members are obtained. The results of this study show that for most of the bridges, LCVs result in the smallest values of Dynamic Amplification Factor (DAF) whereas the Single Unit Trucks cause the highest values of DAF when traveling on the bridges. Also in most cases, the values of DAF are observed to be smaller than the 33% threshold suggested by the design code. Additionally, fatigue analysis of the bridges in this study confirms that by replacing the current truck traffic with higher capacity LCVs, in most cases, the remaining fatigue life of the bridge is only slightly decreased which means that taking advantage of these larger vehicles can be a viable option for decision makers.

Development of Surface Flaw Thresholds for Pre-Cured Fiber Reinforced Polymer and Groove Size Tolerance for Near Surface Mounted Fiber Reinforced Polymer Retrofit Systems

Since the introduction of fiber reinforced polymers (FRP) for the repair and retrofit of concrete structures in the 1980’s, considerable research has been devoted to the feasibility of their application and predictive modeling of their performance. However, the effects of flaws present in the constitutive components and the practices in substrate preparation and treatment have not yet been thoroughly studied. This research aims at investigating the effect of surface preparation and treatment for the pre-cured FRP systems and the groove size tolerance for near surface mounted (NSM) FRP systems; and to set thresholds for guaranteed system performance. The research included both analytical and experimental components. The experimental program for the pre-cured FRP systems consisted of a total of twenty-four (24) reinforced concrete (RC) T-beams with various surface preparation parameters and surface flaws, including roughness, flatness, voids and cracks (cuts). For the NSM FRP systems, a total of twelve (12) additional RC T-beams were tested with different grooves sizes for FRP bars and strips. The analytical program included developing an elaborate nonlinear finite element model using the general purpose software ANSYS. The model was subsequently used to extend the experimental range of parameters for surface flatness in pre-cured FRP systems, and for groove size study in the NSM FRP systems. Test results, confirmed by further analyses, indicated that contrary to the general belief in the industry, the impact of surface roughness on the global performance of pre-cured FRP systems was negligible. The study also verified that threshold limits set for wet lay-up FRP systems can be extended to pre-cured systems. The study showed that larger surface voids and cracks (cuts) can adversely impact both the strength and ductility of pre-cured FRP systems. On the other hand, frequency (or spacing) of surface cracks (cuts) may only affect system ductility rather than its strength. Finally, within the range studied, groove size tolerance of +1/8 in. does not appear to have an adverse effect on the performance of NSM FRP systems.

Concrete and abstract concepts in school age children

The aim of this study is to highlight what kind of information distinguishes abstract and concrete conceptual knowledge in different aged children. A familiarity-rating task has shown that 8-year-olds judged concrete concepts as very familiar while abstract concepts were judged as much less familiar with ratings increasing substantially from age 10 to age 12, according to literature showing that abstract terms are not mastered until adolescence (Schwanenflugel, 1991). The types of relation elicited by abstract and concrete concepts during development were investigated in an association production task. At all considered age levels, concrete concepts mainly activated attributive and thematic relations as well as, to a much lesser extent, taxonomic relations and stereotypes. Abstract concepts, instead, elicited mainly thematic relations and, to a much lesser extent, examples and taxonomic relations. The patterns of relations elicited were already differentiated by age 8, becoming more specific in abstract concepts with age.

Seismic Performance of Hybrid Fiber Reinforced Polymer-Concrete Pier Frame Systems

As an alternative to transverse spiral or hoop steel reinforcement, fiber reinforced polymers (FRPs) were introduced to the construction industry in the 1980's. The concept of concrete-filled FRP tube (CFFT) has raised great interest amongst researchers in the last decade. FRP tube can act as a pour form, protective jacket, and shear and flexural reinforcement for concrete. However, seismic performance of CFFT bridge substructure has not yet been fully investigated. Experimental work in this study included four two-column bent tests, several component tests and coupon tests. Four 1/6-scale bridge pier frames, consisting of a control reinforced concrete frame (RCF), glass FRP-concrete frame (GFF), carbon FRP-concrete frame (CFF), and hybrid glass/carbon FRP-concrete frame (HFF) were tested under reverse cyclic lateral loading with constant axial loads. Specimen GFF did not show any sign of cracking at a drift ratio as high as 15% with considerable loading capacity, whereas Specimen CFF showed that lowest ductility with similar load capacity as in Specimen GFF. FRP-concrete columns and pier cap beams were then cut from the pier frame specimens, and were tested again in three point flexure under monotonic loading with no axial load. The tests indicated that bonding between FRP and concrete and yielding of steel both affect the flexural strength and ductility of the components. The coupon tests were carried out to establish the tensile strength and elastic modulus of each FRP tube and the FRP mold for the pier cap beam in the two principle directions of loading. A nonlinear analytical model was developed to predict the load-deflection responses of the pier frames. The model was validated against test results. Subsequently, a parametric study was conducted with variables such as frame height to span ratio, steel reinforcement ratio, FRP tube thickness, axial force, and compressive strength of concrete. A typical bridge was also simulated under three different ground acceleration records and damping ratios. Based on the analytical damage index, the RCF bridge was most severely damaged, whereas the GFF bridge only suffered minor repairable damages. Damping ratio was shown to have a pronounced effect on FRP-concrete bridges, just the same as in conventional bridges. This research was part of a multi-university project, which is founded by the National Science Foundation (NSF) Network for Earthquake Engineering Simulation Research (NEESR) program.

Establishment of a preconditioning regime for air permeability and sorptivity of alkali-activated slag concrete

This study reports an experimental investigation designed to assess the influence of near-surface moisture contents on permeation properties of alkali-activated slag concrete (AASC). Five different drying periods (5, 10, 15, 20 and 25 days) and three AASC and normal concretes with compressive strength grades ranging from C30 to C60 were considered. Assessment of moisture distribution was
achieved using 100 mm diameter cores with drilled cavities. Results indicate that air permeability of AASC is very sensitive to the moisture content and its spatial distribution, especially at relative humidity above 65%. To control the influence of moisture on permeation testing, the recommendation of this paper is that AASC specimens should be dried in controlled conditions at 40 C for 10 days prior to testing. It was also concluded from this study that AASC tends to perform less well, in terms of air permeability and sorptivity, than normal concrete for a given strength grade. This conclusion reinforces the need to further examine AASC properties prior to its widespread practical use.

Developing an engineering approach for migrating from prescriptive to performance-based specification for concrete

The integral variability of raw materials, lack of awareness and appreciation of the technologies for achieving quality control and lack of appreciation of the micro and macro environmental conditions that the structures will be subjected, makes modern day concreting a challenge. This also makes Designers and Engineers adhere more closely to prescriptive standards developed for relatively less aggressive environments. The data from exposure sites and real structures prove, categorically, that the prescriptive specifications are inadequate for chloride environments. In light of this shortcoming, a more pragmatic approach would be to adopt performance-based specifications which are familiar to industry in the form of specification for mechanical strength. A recently completed RILEM technical committee made significant advances in making such an approach feasible.
Furthering a performance-based specification requires establishment of reliable laboratory and on-site test methods, as well as easy to perform service-life models. This article highlights both laboratory and on-site test methods for chloride diffusivity/electrical resistivity and the relationship between these tests for a range of concretes. Further, a performance-based approach using an on-site diffusivity test is outlined that can provide an easier to apply/adopt practice for Engineers and asset managers for specifying/testing concrete structures.

Creep deflection of low-strength reinforced concrete flexural members strengthened with carbon fiber composite sheets

The low-strength concrete is defined as a concrete where the compressive cubic strength is less than 15 MPa. Since the beginning of the last century, many low-strength concrete buildings and bridges have been built all over the world. Being short of deeper study, composite sheets are prohibited in strengthening of low-strength reinforced concrete members (CECS 146; ACI 440). Moreover, there are few relevant information about the long-term behavior and durability of strengthened RC members. This fact undoubtedly limits the use of the composite materials in the strengthening applications, therefore, it is necessary to study the behaviours of low-strength concrete elements strengthened with composite materials (FRP) for the preservation of historic constructions and innovation in the strengthening technology. Deformability is one of criteria in the design of concrete structures, and this for functionality, durability and aesthetics reasons. Civil engineer possibly encounters more deflection problems in the structural design than any other type of problem. Many materials common in structural engineering such as wood, concrete and composite materials, suffer creep; if the creep phenomenon is taken into account, checks for serviceability limit state criteria can become onerous, because the creep deformation in these materials is in the same order of magnitude as the elastic deformation. The thesis presents the results of an experimental study on the long-term behavior of low-strength reinforced concrete beams strengthened with carbon fiber composite sheets (CFRP). The work has investigated the accuracy of the long-term deflection predictions made by some analytical procedures existing in literature, as well as by the most widely used design codes (Eurocode 2, ACI-318, ACI-435).

Stratégie d'amélioration de la résistance mécanique des zones de connecteurs

Le bois subit une demande croissante comme matériau de construction dans les bâtiments de grandes dimensions. Ses qualités de matériau renouvelable et esthétique le rendent attrayant pour les architectes. Lorsque comparé à des produits fonctionnellement équivalents, il apparait que le bois permet de réduire la consommation d’énergie non-renouvelable. Sa transformation nécessite une quantité d’énergie inférieure que l’acier et le béton. Par ailleurs, par son origine biologique, une structure en bois permet de stocker du carbone biogénique pour la durée de vie du bâtiment. Maintenant permis jusqu’à six étages de hauteur au Canada, les bâtiments de grande taille en bois relèvent des défis de conception. Lors du dimensionnement des structures, les zones des connecteurs sont souvent les points critiques. Effectivement, les contraintes y sont maximales. Les structures peuvent alors apparaitre massives et diminuer l’innovation architecturale. De nouvelles stratégies doivent donc être développées afin d’améliorer la résistance mécanique dans les zones de connecteurs. Différents travaux ont récemment porté sur la création ou l’amélioration de types d’assemblage. Dans cette étude, l’accent est mis sur le renforcement du bois utilisé dans la région de connexion. L’imprégnation a été choisie comme solution de renfort puisque la littérature démontre qu’il est possible d’augmenter la dureté du bois avec cette technique. L’utilisation de cette stratégie de renfort sur l’épinette noire (Picea Mariana (Mill.) BSP) pour une application structurale est l’élément de nouveauté dans cette recherche. À défaut d’effectuer une imprégnation jusqu’au coeur des pièces, l’essence peu perméable de bois employée favorise la création d’une mince couche en surface traitée sans avoir à utiliser une quantité importante de produits chimiques. L’agent d’imprégnation est composé de 1,6 hexanediol diacrylate, de triméthylopropane tricacrylate et d’un oligomère de polyester acrylate. Une deuxième formulation contenant des nanoparticules de SiO2 a permis de vérifier l’effet des nanoparticules sur l’augmentation de la résistance mécanique du bois. Ainsi, dans ce projet, un procédé d’imprégnation vide-pression a servi à modifier un nouveau matériau à base de bois permettant des assemblages plus résistants mécaniquement. Le test de portance locale à l’enfoncement parallèle au fil d’un connecteur de type tige a été réalisé afin de déterminer l’apport du traitement sur le bois utilisé comme élément de connexion. L’effet d’échelle a été observé par la réalisation du test avec trois diamètres de boulons différents (9,525 mm, 12,700 mm et 15,875 mm). En outre, le test a été effectué selon un chargement perpendiculaire au fil pour le boulon de moyen diamètre (12,700 mm). La corrélation d’images numériques a été utilisée comme outil d’analyse de la répartition des contraintes dans le bois. Les résultats ont démontré une portance du bois plus élevée suite au traitement. Par ailleurs, l’efficacité est croissante lorsque le diamètre du boulon diminue. C’est un produit avec une valeur caractéristique de la portance locale parallèle au fil de 79% supérieure qui a été créé dans le cas du test avec le boulon de 9,525 mm. La raideur du bois a subi une augmentation avoisinant les 30%. Suite au traitement, la présence d’une rupture par fissuration est moins fréquente. Les contraintes se distribuent plus largement autour de la région de connexion. Le traitement n’a pas produit d’effet significatif sur la résistance mécanique de l’assemblage dans le cas d’un enfoncement du boulon perpendiculairement au fil du bois. De même, l’effet des nanoparticules en solution n’est pas ressorti significatif. Malgré une pénétration très faible du liquide à l’intérieur du bois, la couche densifiée en surface créée suite au traitement est suffisante pour produire un nouveau matériau plus résistant dans les zones de connexion. Le renfort du bois dans la région des connecteurs doit influencer le dimensionnement des structures de grande taille. Avec des éléments de connexion renforcés, il sera possible d’allonger les portées des poutres, multipliant ainsi les possibilités architecturales. Le renfort pourra aussi permettre de réduire les sections des poutres et d’utiliser une quantité moindre de bois dans un bâtiment. Cela engendrera des coûts de transport et des coûts reliés au temps d’assemblage réduits. De plus, un connecteur plus résistant permettra d’être utilisé en moins grande quantité dans un assemblage. Les coûts d’approvisionnement en éléments métalliques et le temps de pose sur le site pourront être revus à la baisse. Les avantages d’un nouveau matériau à base de bois plus performant utilisé dans les connexions permettront de promouvoir le bois dans les constructions de grande taille et de réduire l’impact environnemental des bâtiments.

Comportamento e reforço de nós viga-pilar

A presente dissertação tem como principal objetivo a análise do comportamento do nó viga-pilar, com a finalidade de dimensionar uma solução de reforço sísmico a aplicar em nós de estruturas antigas de betão armado. Uma parte considerável das construções em betão armado construídas em Portugal até 1970 são muito frágeis relativamente às ações sísmicas. Devido a este fato, os edifícios estão associados a uma conceção desajustada face à regulamentação atual pois à época não estava prevista a consideração de ações sísmicas na execução dos projetos de estruturas. Nesse período, era prática comum na construção o uso de armadura lisa conjugada com uma má pormenorização das armaduras e baixa resistência mecânica do betão. Tal levava a que as estruturas de betão armado construídas em Portugal até à década de setenta, possuírem uma baixa capacidade para resistir a solicitações cíclicas, como as induzidas pelos sismos. Os nós viga-pilar das estruturaras de betão armado são considerados as zonas mais crítica e vulnerável a ações sísmicas. Por isso é frequente em estruturas antigas, a necessidade de as reforçar, para melhorar a performance do edifício durante os sismos. Têm sido estudadas por investigadores várias técnicas e soluções para reforçar os nós viga-pilar de estruturas antigas de betão armado. Serão analisados nesta dissertação os danos observados em dois nós viga-pilar ensaiados experimentalmente, onde são simuladas as ações cíclicas horizontais dos sismos. Com base nestes dados, é proposta e detalhada uma solução de reforço para melhorar o comportamento histerético dessa ligações, de forma a conferir uma maior capacidade resistente e/ou ductilidade.

DESIGN, FABRICATION, AND PERFORMANCE CHARACTERIZATION OF MULTIFUNCTIONAL STRUCTURES TO HARVEST SOLAR ENERGY FOR FLAPPING WING AERIAL VEHICLES

Flapping Wing Aerial Vehicles (FWAVs) have the capability to combine the benefits of both fixed wing vehicles and rotary vehicles. However, flight time is limited due to limited on-board energy storage capacity. For most Unmanned Aerial Vehicle (UAV) operators, frequent recharging of the batteries is not ideal due to lack of nearby electrical outlets. This imposes serious limitations on FWAV flights. The approach taken to extend the flight time of UAVs was to integrate photovoltaic solar cells onto different structures of the vehicle to harvest and use energy from the sun. Integration of the solar cells can greatly improve the energy capacity of an UAV; however, this integration does effect the performance of the UAV and especially FWAVs. The integration of solar cells affects the ability of the vehicle to produce the aerodynamic forces necessary to maintain flight. This PhD dissertation characterizes the effects of solar cell integration on the performance of a FWAV. Robo Raven, a recently developed FWAV, is used as the platform for this work. An additive manufacturing technique was developed to integrate photovoltaic solar cells into the wing and tail structures of the vehicle. An approach to characterizing the effects of solar cell integration to the wings, tail, and body of the UAV is also described. This approach includes measurement of aerodynamic forces generated by the vehicle and measurements of the wing shape during the flapping cycle using Digital Image Correlation. Various changes to wing, body, and tail design are investigated and changes in performance for each design are measured. The electrical performance from the solar cells is also characterized. A new multifunctional performance model was formulated that describes how integration of solar cells influences the flight performance. Aerodynamic models were developed to describe effects of solar cell integration force production and performance of the FWAV. Thus, performance changes can be predicted depending on changes in design. Sensing capabilities of the solar cells were also discovered and correlated to the deformation of the wing. This demonstrated that the solar cells were capable of: (1) Lightweight and flexible structure to generate aerodynamic forces, (2) Energy harvesting to extend operational time and autonomy, (3) Sensing of an aerodynamic force associated with wing deformation. Finally, different flexible photovoltaic materials with higher efficiencies are investigated, which enable the multifunctional wings to provide enough solar power to keep the FWAV aloft without batteries as long as there is enough sunlight to power the vehicle.

Projeto de estabilidade de um edifício para uma sala elétrica em betão armado e estrutura metálica

Trabalho de Projeto para obtenção do grau de Mestre em Engenharia Civil na Área de Especialização Estruturas