Avaliação da aplicação de modelos para a secagem de pastas e suspensões em leito de jorro com alimentação contínua

This work studies the development, implementation and improvement of a macroscopic model to describe the behavior of the spouted bed dryer with continuous feeding for pastes and suspensions drying. This model is based on the CST model (Freire et al., 2009) and the model of Fernandes (2005), whose theoretical foundation is based on macroscopic mass and heat balances for the three phases involved in the process: gas, liquid and solid. Because this technique is quite relevant, the studies of modeling and simulation of spouted bed drying are essential in the analysis of the process as a whole, because through them it is possible to predict and understand the behavior of the process, which contributes significantly to more efficient project and operation. The development and understanding of the phenomena involved in the drying process can be obtained by comparing the experimental data with those from computer simulations. Such knowledge is critical for choosing properly the process conditions in order to obtain a good drying efficiency. Over the past few years, researches and development of works in the field of pastes and suspensions drying in spouted bed has been gaining ground in Brazil. The Particulate Systems Laboratory at Universidade Federal do Rio Grande do Norte, has been developing several researches and generating a huge collection of experimental data concerning the drying of fruit pulps, vegetables pastes, goat milk and suspensions of agro-industrial residues. From this collection, some data of goat milk and residue from acerola (Malpighia glabra L.) drying were collected. For the first time, these data were used for the development and validation of a model that can describe the behavior of spouted bed dryer. Thus, it was possible to model the dryer and to evaluate the influence of process variables (paste feeding, temperature and flow rate of the drying air) in the drying dynamics. We also performed water evaporation experiments in order to understand and to study the behavior of the dryer wall temperature and the evaporation rate. All these analysis will contribute to future works involving the implementation of control strategies in the pastes and suspensions drying. The results obtained in transient analysis were compared with experimental data indicating that this model well represents the process

Can native vegetation recover after slash pine cultivation in the Brazilian Savanna?

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Estudo da produção de pectinase por fermentação em estado sólido utilizando pedúnculo de caju como substrato

Pectinolytic enzymes, or simply pectinases, are complex enzymes that degrade pectic polymers. They have many uses, such as fruit juice extraction and purification, textile fiber treatment and vegetal oil extraction. The aim of this work was to study the kinetics of pectinases production by solid-state fermentation, using dry cashew apple residue as substrate and the microorganism Aspergillus niger CCT 0916. The influence of the initial medium moisture and medium supplementation with a source of nitrogen and phosphorus was evaluated using the factorial experimental planning and response surface methodology. Ammonia sulphate and potassium phosphate were used as nitrogen and phosphorus source, respectively. The variables time of contact (T) and ratio volume solvent/fermented medium (RZ), in systems with and without agitation, were evaluated in order to study the best extraction condition of the produced enzyme. Washed and unwashed cashew apple residues were tested as the growth medium. The unwashed residue was obtained by drying the residue after the extraction of the juice, while the washed residue was obtained by water washing 5 times using the proportion of 1 kg pulp/2 liters of water. Samples were taken every 12 hours for moisture content, pH, protein, reducing sugars, polygalacturonase activity (PG) and viscosity reduction. The physical-chemical composition of the residues had different sugar and pectin levels. For the unwashed residue, the peak activity was reached with 40% of initial moisture content, 1% of nitrogen supplementation without phosphorus addition after 30 hours of process. These conditions led to 16 U/g of PG activity and 82% of viscosity reduction. The calculated models reached similar values to the experimental ones in the same process conditions: 15.55 U/g of PG and 79.57% of viscosity eduction. Similarly, the greatest enzyme production for washed residue was reached with 40% initial moisture content, 1% nitrogen supplementation without phosphorus addition after 22 hours of cultivation. In this condition it was obtained polygalacturonase activity of 9.84 U/g and viscosity reduction of 81.36%. These values are close to experimental values that were of 10.1 U/g and 81%, respectively. The conditions that led to the best PG activity results was the agitated one and the best extraction condition was obtained with 100 minutes of solvent/medium contact and RZ of 5 (mL/g)

Avaliação e modelagem da absorção de H2S do gás natural em coluna de leito estagnado

Natural gas, although basically composed by light hydrocarbons, also presents contaminant gases in its composition, such as CO2 (carbon dioxide) and H2S (hydrogen sulfide). The H2S, which commonly occurs in oil and gas exploration and production activities, causes damages in oil and natural gas pipelines. Consequently, the removal of hydrogen sulfide gas will result in an important reduction in operating costs. Also, it is essential to consider the better quality of the oil to be processed in the refinery, thus resulting in benefits in economic, environmental and social areas. All this facts demonstrate the need for the development and improvement in hydrogen sulfide scavengers. Currently, the oil industry uses several processes for hydrogen sulfide removal from natural gas. However, these processes produce amine derivatives which can cause damage in distillation towers, can cause clogging of pipelines by formation of insoluble precipitates, and also produce residues with great environmental impact. Therefore, it is of great importance the obtaining of a stable system, in inorganic or organic reaction media, able to remove hydrogen sulfide without formation of by-products that can affect the quality and cost of natural gas processing, transport, and distribution steps. Seeking the study, evaluation and modeling of mass transfer and kinetics of hydrogen removal, in this study it was used an absorption column packed with Raschig rings, where the natural gas, with H2S as contaminant, passed through an aqueous solution of inorganic compounds as stagnant liquid, being this contaminant gas absorbed by the liquid phase. This absorption column was coupled with a H2S detection system, with interface with a computer. The data and the model equations were solved by the least squares method, modified by Levemberg-Marquardt. In this study, in addition to the water, it were used the following solutions: sodium hydroxide, potassium permanganate, ferric chloride, copper sulfate, zinc chloride, potassium chromate, and manganese sulfate, all at low concentrations (»10 ppm). These solutions were used looking for the evaluation of the interference between absorption physical and chemical parameters, or even to get a better mass transfer coefficient, as in mixing reactors and absorption columns operating in counterflow. In this context, the evaluation of H2S removal arises as a valuable procedure for the treatment of natural gas and destination of process by-products. The study of the obtained absorption curves makes possible to determine the mass transfer predominant stage in the involved processes, the mass transfer volumetric coefficients, and the equilibrium concentrations. It was also performed a kinetic study. The obtained results showed that the H2S removal kinetics is greater for NaOH. Considering that the study was performed at low concentrations of chemical reagents, it was possible to check the effect of secondary reactions in the other chemicals, especially in the case of KMnO4, which shows that your by-product, MnO2, acts in H2S absorption process. In addition, CuSO4 and FeCl3 also demonstrated to have good efficiency in H2S removal

Análise experimental de blocos intertravados de concreto com adição de resíduos do processo de recauchutagem de pneus

Analysis of experimental interlocking blocks of concrete with addition of residues of process the tires retreading production. With the population growth in recent years, industry in general has adjusted itself to resulting demand. the industry of tire retreading generates residues that have been discarded without any control. this adds to environmental pollution and promotes the proliferation of vectors harmful to health, aiming to find an application for this type of residues, this study presents experimental results to interlocking concrete block pavements, with addition of residues tires, interlocking blocks were built up and we determined, through laboratory tests, the need to set the mark that provide greater return regarding analyzed characteristics, there are four types of dosage of concrete with residues tires. We accomplished tests of compression strength, water absorption and resistance to impact. Through the preliminary results, we verified that are satisfactory, confirming the possibility of applying this type of interlocking block in environments with low demand, which would bring the economy of natural sources of aggregates, beyond ecological benefits through the reuse of residues from retreading of tires.

Cerâmicas avançadas no processo de retificação cilíndrica externa de mergulho com rebolos diamantados com a técnica da mímima quantidade de lubrificação e refrigeração otimizada

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Cellulose pyrolysis and quantum chemistry

Cellulose is the major constituent of most plants of interest as renewable sources of energy and is the most extensively studied form of biomass or biomass constituent. Predicting the mass loss and product yields when cellulose is subjected to increased temperature represents a fundamental problem in the thermal release of biomass energy. Unfortunately, at this time, there is no internally consistent model of cellulose pyrolysis that can organize the varied experimental data now available or provide a guide for additional experiments. Here, we present a model of direct cellulose pyrolysis using a multistage decay scheme that we first presented in the IJQC in 1984. This decay scheme can, with the help of an inverse method of assigning reaction rates, provide a reasonable account of the direct fast pyrolysis yield measurements. The model is suggestive of dissociation states of d-glucose (C6H10O5,), the fundamental cellulose monomer. The model raises the question as to whether quantum chemistry could now provide the dissociation energies for the principal breakup modes of glucose into C-1, C-2, C-3, C-4, and C-5 compounds. These calculations would help in achieving a more fundamental description of volatile generation from cellulose pyrolysis and could serve as a guide for treating hemicellulose and lignin, the other major biomass constituents. Such advances could lead to the development of a predictive science of biomass pyrolysis that would facilitate the design of liquifiers and gasifiers based upon renewable feedstocks. (C) 1998 John Wiley & Sons, Inc.

Radial Plasma Dynamic in Sequential Pinches

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Avaliação da prevenção de falhas em processos utilizando métodos de tomada de decisão

Este trabalho apresenta uma investigação sobre o emprego de FMEA (Failure Mode and Effect Analysis) de Processo com a exposição de irregularidades na sua utilização. O método AHP (Analytic Hierarchy Process) e os Conjuntos Fuzzy são aplicados no estudo das práticas atuais de utilização de FMEA. O AHP é aplicado para a priorização das irregularidades quanto à gravidade de sua ocorrência. Os Conjuntos Fuzzy são aplicados para avaliação do desempenho da utilização de FMEA em algumas empresas do ramo automotivo. Como resultado, tem-se a aceitação de oito e a não aceitação de três dos onze formulários de FMEA averiguados.

The Synthetic Control Chart Based on Two Sample Variances for Monitoring the Covariance Matrix

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

The double sampling and the EWMA charts based on the sample variances

We propose a new statistic to control the covariance matrix of bivariate processes. This new statistic is based on the sample variances of the two quality characteristics, in short VMAX statistic. The points plotted on the chart correspond to the maximum of the values of these two variances. The reasons to consider the VMAX statistic instead of the generalized variance vertical bar S vertical bar is its faster detection of process changes and its better diagnostic feature; that is, with the VMAX statistic it is easier to identify the out-of-control variable. We study the double sampling (DS) and the exponentially weighted moving average (EWMA) charts based on the VMAX statistic. (C) 2008 Elsevier B.V. All rights reserved.

Avaliação do programa de tutorização da EMATER-RN para servidores em estágio probatório

The present thesis evaluated the contributions and limitations of the tutorship program introduced in EMATER-RN, as a tactic of organizational socialization for civil servants in probationary stage. Tutorship was understood as an intensive and continuous relational process, in which a more experienced person in the organization the tutor offers psychosocial support, stimulates the development of the professional career and enables to the newcomer the tutee learning on job performance. The organizational socialization was considered in the perspective of the symbolic interactionism. The study was characterized as a program evaluation and as an action research. The practical interventions for the program implementation were conducted and, at the same time, the evaluations of process, results and reaction to the program were applied. Among the major contributions of the action research, it stood out: the diagnosis of reasons for the formation of the pair and of expectations of tutors and tutees, the improvement of the tutorship registration tools, the ascertainment of the success of the program in the socialization of the new civil servants, the confirmation of the importance of the compatibility among them and of the adequate performance of tutorship functions for achieving its benefits. Based in constraints of the program, one may quote as essential recommendations: the formation of a technical team supporting the program, the clear establishment of deadlines for each procedure and the reinforcement to its compliance, the investigation of the functions performed by the tutor, the sensitization of the managers to the resolution of problems that affect the program, the voluntary participation of the tutor and the continuous meetings of tutors and tutees. One settles for the relevance of the program and in favor of its continuation, provided that its improvement and systematic management are conducted.

CrossMDA-SPL: uma abordagem para gerência de variabilidades dirigida por modelos e aspectos

This paper proposes a systematic approach to management of variability modelsdriven and aspects using the mechanisms of approaches Aspect-Oriented Software Development (AOSD) and Model-Driven Development (MDD). The main goal of the approach, named CrossMDA-SPL, is to improve the management(gerência), modularization and isolation ou separation of the variability of the LPSs of architecture in a high level of abstraction (model) at the design and implementing phases of development Software Product Lines (SPLs), exploiting the synergy between AOSD and MDD. The CrossMDA-SPL approach defines some artifacts basis for advance the separation clear in between the mandatory (bounden) and optional features in the architecture of SPL. The artifacts are represented by two models named: (i) core model (base domain) - responsible for specify the common features the all members of the SPL, and (ii) variability model - responsible for represent the variables features of SPL. In addition, the CrossMDA-SPL approach is composed of: (i) guidelines for modeling and representation of variability, (ii) CrossMDA-SPL services and process, and (iii) models of the architecture of SPL or product instance of SPL. The guidelines use the advantages of AOSD and MDD to promote a better modularization of the variable features of the architecture of SPL during the creation of core and variability models of the approach. The services and sub-processes are responsible for combination automatically, through of process of transformation between the core and variability models, and the generation of new models that represent the implementation of the architecture of SPL or a instance model of SPL. Mechanisms for effective modularization of variability for architectures of SPL at model level. The concepts are described and measured with the execution of a case study of an SPL for management systems of transport electronic tickets

Uma abordagem dirigida por modelos para gerência de variabilidade e execução de processos de software

This dissertation presents a model-driven and integrated approach to variability management, customization and execution of software processes. Our approach is founded on the principles and techniques of software product lines and model-driven engineering. Model-driven engineering provides support to the specification of software processes and their transformation to workflow specifications. Software product lines techniques allows the automatic variability management of process elements and fragments. Additionally, in our approach, workflow technologies enable the process execution in workflow engines. In order to evaluate the approach feasibility, we have implemented it using existing model-driven engineering technologies. The software processes are specified using Eclipse Process Framework (EPF). The automatic variability management of software processes has been implemented as an extension of an existing product derivation tool. Finally, ATL and Acceleo transformation languages are adopted to transform EPF process to jPDL workflow language specifications in order to enable the deployment and execution of software processes in the JBoss BPM workflow engine. The approach is evaluated through the modeling and modularization of the project management discipline of the Open Unified Process (OpenUP)

PUPSI :uma proposta de processo unificado para políticas de segurança da informação

The way to deal with information assets means nowadays the main factor not only for the success but also for keeping the companies in the global world. The number of information security incidents has grown for the last years. The establishment of information security policies that search to keep the security requirements of assets in the desired degrees is the major priority for the companies. This dissertation suggests a unified process for elaboration, maintenance and development of information security policies, the Processo Unificado para Políticas de Segurança da Informação - PUPSI. The elaboration of this proposal started with the construction of a structure of knowledge based on documents and official rules, published in the last two decades, about security policies and information security. It's a model based on the examined documents which defines the needed security policies to be established in the organization, its work flow and identifies the sequence of hierarchy among them. It's also made a model of the entities participating in the process. Being the problem treated by the model so complex, which involves all security policies that the company must have. PUPSI has an interative and developing approach. This approach was obtained from the instantiation of the RUP - Rational Unified Process model. RUP is a platform for software development object oriented, of Rational Software (IBM group). Which uses the best practice known by the market. PUPSI got from RUP a structure of process that offers functionality, diffusion capacity and comprehension, performance and agility for the process adjustment, offering yet capacity of adjustment to technological and structural charges of the market and the company