Consumerist Predators"? Emerging lifestyles between McDonaldization and sustainability perspectives: the case of highly qualified employees (HQEs) in India

In industrializing countries new groups of consumers with remarkable purchasing power are emerging. Representing a ?new middle class? they are seen as a carrier and promoter of a so-called ?western way of life? beyond the OECD countries. They are presented as having a consumerist predator lifestyle which stands in conflict with the requirements for a sustainable future. Furthermore, they are imputed a profound lack of a sense of responsibility towards society. However, such a ?civil society spirit? is a core prerequisite for coping with the challenge of changing existing lifestyles to insure a more sustainable future....

Influence of melt pouring temperature and plate inclination on solidification and microstructure of A356 aluminum alloy produced using oblique plate

The preparation of semisolid slurry of A356 aluminum alloy using an oblique plate was investigated. A356 alloy melt undergoes partial solidification when it flows down on an oblique plate cooled from underneath by counter flowing water. It results in continuous formation of columnar dendrites on plate wall. Due to forced convection, these dendrites are sheared off into equiaxed/fragmented grains and then washed away continuously to produce semisolid slurry at plate exit. Melt pouring temperature provides required condition of solidification whereas plate inclination enables necessary shear for producing semisolid slurry of desired quality. Slurry obtained was solidified in metal mould to produce semisolid-cast billets of desired microstructure. Furthermore, semisolid-cast billets were heat treated to improve surface quality. Microstructures of both semisolid-cast and heat-treated billets were analyzed. Effects of melt pouring temperature and plate inclination on solidification and microstructure of billets produced using oblique plate were described. The investigations involved four different melt pouring temperatures (620, 625, 630 and 635 degrees C) associated with four different plate inclinations (30 degrees, 45 degrees, 60 degrees and 75 degrees). Melt pouring temperature of 625 degrees C with plate inclination of 60 degrees shows fine and globular microstructures and it is the optimum.

Influence of plate length and plate cooling rate on solidification and microstructure of A356 alloy produced by oblique plate

A356 alloy melt solidifies partially when it flows down on an oblique plate cooled from bottom by counter flowing water. Columnar dendrites are continuously formed on the plate wall. Because of the forced convection, these dendrites are sheared off into equiaxed/fragmented grains and then washed away continuously by producing semisolid slurry at plate exit. Plate cooling rate provides required extent/amount of solidification whereas plate length enables necessary shear for producing semisolid slurry of desired quality. Slurry obtained is solidified in metal mould to produce semisolid-cast billets of desired microstructure. Furthermore, semisolid-cast billets are also heat-treated to improve surface quality. Microstructures of both semisolid-cast and heat-treated billets are compared. The effects of plate length and plate cooling rate on solidification and microstructure of billets produced by using oblique plate are illustrated. Three different plate lengths (200 mm, 250 mm, 300 mm) associated with three different heat transfer coefficients (1000, 2000 and 2500 W/(m(2).K)) are involved. Plate length of 250 mm with heat transfer coefficient of 2000 W/(m(2).K) gives fine and globular microstructures and is the optimum as there is absolutely no possibility of sticking of slurry to plate wall.

An Extension of 2D Janbu’s Generalized Procedure of Slices for 3D Slope Stability Analysis II—Numerical Method and Applications

This paper provides a numerical approach on achieving the limit equilibrium method for 3D slope stability analysis proposed in the theoretical part of the previous paper. Some programming techniques are presented to ensure the maneuverability of the method. Three examples are introduced to illustrate the use of this method. The results are given in detail such as the local factor of safety and local potential sliding direction for a slope. As the method is an extension of 2D Janbu's generalized procedure of slices (GPS), the results obtained by GPS for the longitudinal sections of a slope are also given for comparison with the 3D results. A practical landslide in Yunyang, the Three Gorges, of China, is also analyzed by the present method. Moreover, the proposed method has the advantages and disadvantages of GPS. The problem frequently encountered in calculation process is still about the convergency, especially in analyzing the stability of a cutting corner. Some advice on discretization is given to ensure convergence when the present method is used. However, the problem about convergency still needs to be further explored based on the rigorous theoretical background.

Space experimental device on Marangoni drop migrations of large Reynolds numbers

The space experimental device for testing the Marangoni drop migrations has been discussed in the present paper. The experiment is one of the spaceship projects of China. In comparison with similar devices, it has the ability of completing all the scientific experiments by both auto controlling and telescience methods. It not only can perform drop migration experiments of large Reynolds numbers but also has an equi-thick interferential system.

Undercooling and Rapid Solidification of Nb-Si Eutectic Alloys Studied by Long Drop Tube

Niobium-silicide alloys have great potential for high temperature turbine applications. The two-phase Nb/Nb5Si3 in situ composites exhibit a good balance in mechanical properties. Using the 52 in drop tube, the effect of undercooling and rapid solidification on the solidification process and micro-structural characterization of Nb-Si eutectic alloy was studied. The microstructures of the Nb-Si composites were investigated by optics microscope (OM), X-ray diffraction (XRD) and scanning electron microscope (SEM) equipped with X-ray energy dispersive spectrometry (EDS). Up to 480 K, deep undercooling of the Nb-Si eutectic samples was successfully obtained, which corresponds to 25% of the liquidus temperature. Contrasting to the conventional microstructure usually found in the Nb-Si eutectic alloy, the microstructure of the undercooled sample is divided into the fine and coarse regions. The most commonly observed microstructure is Nb+Nb5Si3, and the Nb3Si phase is not be found. The change of coarseness of microstructure is due to different cooling rates during and after recalescence. The large undercooling is sufficient to completely bypass the high temperature phase field.

Combustion and Ignition of Thermally Cracked Kerosene in Supersonic Model Combustors

A series of experiments were conducted to characterize the self-ignition and combustion of thermally cracked kerosene in both a Mach 2.5 model combustor with a combustor entrance height of 51 mm and a Mach 3.0 model combustor with an entrance height of 70 mm. A unique kerosene heating and delivery system was developed, which can prepare heated kerosene up to 950 K at a pressure of 5.5 MPa with negligible fuel coking. The extent of China no. 3 kerosene conversion under supercritical conditions was measured using a specially designed system. The compositions of gaseous products as a result of thermal cracking were analyzed using gas chromatography. The mass flow rates of cracked kerosene were also calibrated and measured using sonic nozzles. With the injection of thermally cracked kerosene, the ability to achieve enhanced combustion performance was demonstrated under a variety of airflow and fuel conditions. Furthermore, self-ignition tests of cracked kerosene in a Mach 2.5 model combustor over a range of fuel injection conditions and with the help of different amounts of pilot hydrogen were conducted and discussed.

Progress In Modeling Of Fluid Flows In Crystal Growth Processes

Modeling of fluid flows in crystal growth processes has become an important research area in theoretical and applied mechanics. Most crystal growth processes involve fluid flows, such as flows in the melt, solution or vapor. Theoretical modeling has played an important role in developing technologies used for growing semiconductor crystals for high performance electronic and optoelectronic devices. The application of devices requires large diameter crystals with a high degree of crystallographic perfection, low defect density and uniform dopant distribution. In this article, the flow models developed in modeling of the crystal growth processes such as Czochralski, ammonothermal and physical vapor transport methods are reviewed. In the Czochralski growth modeling, the flow models for thermocapillary flow, turbulent flow and MHD flow have been developed. In the ammonothermal growth modeling, the buoyancy and porous media flow models have been developed based on a single-domain and continuum approach for the composite fluid-porous layer systems. In the physical vapor transport growth modeling, the Stefan flow model has been proposed based on the flow-kinetics theory for the vapor growth. In addition, perspectives for future studies on crystal growth modeling are proposed. (c) 2008 National Natural Science Foundation of China and Chinese Academy of Sciences. Published by Elsevier Limited and Science in China Press. All rights reserved.

Microstructure and mechanical properties of Zr-Cu-Al bulk metallic glasses

Zr49Cu46Al5 and Zr48.5Cu46.5Al5 bulk metallic glasses(BMGs) with diameter of 5 mm were prepared through water-cooled copper mold casting. The phase structures of the two alloys were identified by X-ray diffractometry(XRD). The thermal stability was examined by differential scanning calorimetry(DSC). Zr49Cu46Al5 alloy shows a glass transition temperature, T, of about 689 K, an crystallization temperature, T-x, of about 736 K. The Zr48.5Cu46.5Al5 alloy shows no obvious exothermic peak. The microstructure of the as-cast alloys was analyzed by transmission electron microscopy(TEM). The aggregations of CuZr and CuZr2 nanocrystals with grain size of about 20 nm are observed in Zr49Cu46Al5 nanocrystalline composite, while the Zr48.5Cu46.5Al5 alloy containing many CuZr martensite plates is crystallized seriously. Mechanical properties of bulk Zr49Cu46Al5 nanocrystalline composite and Zr48.5Cu46.5Al5 alloy measured by compression tests at room temperature show that the work hardening ability of Zr48.5Cu46.5Al5 alloy is larger than that of Zr48.5Cu46.5Al5 alloy.

Finite element analysis on stresses field of normalized layer thickness within ceramic coating on aluminized steel

Multilayer ceramic coatings were fabricated on steel substrate using a combined technique of hot dipping aluminum(HDA) and plasma electrolytic oxidation(PEO). A triangle of normalized layer thickness was created for describing thickness ratios of HDA/PEO coatings. Then, the effect of thickness ratio on stresses field of HDA/PEO coatings subjected to uniform normal contact load was investigated by finite element method. Results show that the surface tensile stress is mainly affected by the thickness ratio of Al layer when the total thickness of coating is unchanged. With the increase of A] layer thickness, the surface tensile stress rises quickly. When Al2O3 layer thickness increases, surface tensile stress is diminished. 'Meanwhile, the maximum shear stress moves rapidly towards internal part of HDA/PEO coatings. Shear stress at the Al2O3/Al interface is minimal when Al2O3 layer and Al layer have the same thickness.

Coflow jets with large velocity difference - a new aerodynamic principle of flame stabilization and combustion intensification

A new aerodynamic principle of flame stabilization and combustion intensification, the coflow jets with large velocity difference, is described. One or more small high-velocity jets of air or steam, injected off the axis and in the same direction as the low-velocity main fuel-air flow into the combustor, create a large recirculation zone of high turbulence intensity in which the combustibles and high temperature gases are effectively mixed, so that stable and intensive combustion can be maintained even for fuels with poor ignition. A pulverized coal combustor based on the principle mentioned above is shown to be characteristic of excellent combustoom and a simple structure. A number of precombustors of this type are in operation at some power stations and industrial boilers of China. Using such precombustor, successtul startups and part-load operation of the boilers have become available under conditions of unpreheated air and low-grade coal with volatiles as low as 15% and ash content as high as 30%. This principle shows good promise as an attractive new technology of combustion.

Report of the Study Group on “Ecosystem-Based Management Science and its application to the North Pacific”

EXECUTIVE SUMMARY INTRODUCTION OVERVIEW OF INTERNATIONAL EBM HISTORY References CANADA Overview Activities to date Integrated Management implementation in Canada Objectives, indicators and reference points Assessment approaches Research directions for the future Management directions for the future References JAPAN Overview Conservation and sustainable use of marine living resources Harvest control by TAC system Stock Recovery Plan and effort regulation system Stock enhancement by hatchery-produced juvenile release Conservation and sustainable develop-ment on coastal waters The implementation of ecosystem-based management PEOPLE’S REPUBLIC OF CHINA Overview Current actions Output control Input control Summer fishing ban Enhance ecosystem health REPUBLIC OF KOREA Initiatives and actions of ecosystem-based management in Korea Current ecosystem-based management initiatives in Korea Precautionary TAC-based fishery management Closed fishing season/areas Fish size- and sex-controls Fishing gear design restrictions Marine protected areas (MPA) RUSSIA Existing and anticipated ecosystem-based management initiatives Issues related to the implementation of ecosystem-based management UNITED STATES OF AMERICA Definitions and approaches to ecosystem-based fishery management in the United States Present U.S. legislative mandates relating to ecosystem-based fishery management Target species Bycatch species Threatened or endangered species Habitats Food webs Ecosystems Integration of legislative mandates into an ecosystem approach Scientific issues in implementing ecosystem-based approaches References DISCUSSION AND RECOMMENDATIONS APPENDICES Appendix 10.1 Study group membership and participants Appendix 10.2 Terminology definitions Appendix 10.3 Present state of implementing ecosystem-based fishery management in Alaska: Alaska groundfish fisheries Appendix 10.4 Present state of implementing ecosystem-based fishery management off the West Coast of the United States: Pacific Coast groundfish fisheries Appendix 10.5 Descriptions of multi-species and ecosystem models developed or under development in the U.S. North Pacific region that might be used to predict effects of fishing on ecosystems Appendix 10.6 A potential standard reporting format (developed by Australia, and currently being used by the U.S.A in their contribution to this report) (83 page document)

Harmful algal blooms in the PICES region of the North Pacific

Foreword Background and objectives [pdf, 0.84 MB] Country reviews and status reports Section I. Western North Pacific Japan Yasuwo Fukuyo, Ichiro Imai, Masaaki Kodama and Kyoichi Tamai Red tides and harmful algal blooms in Japan [pdf, 0.7 MB] People's Republic of China Tian Yan, Ming-Jiang Zhou and Jing-Zhong Zou A national report of HABs in China [pdf, 0.24 MB] Republic of Korea Sam Geun Lee, Hak Gyoon Kim, Eon Seob Cho and Chang Kyu Lee Harmful algal blooms (red tides): Management and mitigation in Korea [pdf, 0.27 MB] Russia Tatiana Y. Orlova, Galina V. Konovalova, Inna V. Stonik, Tatiana V. Morozova and Olga G. Shevchenko Harmful algal blooms on the eastern coast of Russia [pdf, 1.4 MB] Section II. Eastern North Pacific Canada F.J.R. "Max" Taylor and Paul J. Harrison Harmful marine algal blooms in western Canada [pdf, 0.87 MB] United States of America Vera L. Trainer Harmful algal blooms on the U.S. west coast [pdf, 0.5 MB] Mexico Jose L. Ochoa, S. Lluch-Cota, B.O. Arredondo-Vega, E. Nuñes-Vázquez, A. Heredia-Tapia, J. Pérez-Linares and R. Alonso-Rodriguez Marine Biotoxins and harmful algal blooms in Mexico's Pacific littora [pdf, 0.2 MB] Summary and conclusions [pdf, 0.6 MB] Appendices A. Members of the Working Group [pdf, 0.1 MB] B. Original terms of reference (Vladivostok, 1999) [pdf, 0.08 MB] C. Annual reports of WG 15 [pdf, 0.15 MB] D. Workshop report on taxonomy and identification of HAB species and data management [pdf, 0.15 MB] (Document pdf contains 156 pages)

Ecology of Juvenile Walleye Pollock, Theragra chalcogramma: Papers from the workshop "The Importance of Prerecruit Walleye Pollock to the Bering Sea and North Pacific Ecosystems" Seattle, Washington, 28-30 October 1993

The Alaska Fisheries Science Center (AFSC), National Marine Fisheries Service (NMFS), hosted an international workshop, 'The Importance of Prerecruit Walleye Pollock to the Bering Sea and North Pacific Ecosystems," from 28 to 30 October 1993. This workshop was held in conjunction with the annual International North Pacific Marine Science Organization (PICES) meeting held in Seattle. Nearly 100 representatives from government agencies, universities, and the fishing industry in Canada, Japan, the People's Republic of China, Russia, and the United States took part in the workshop to review and discuss current knowledge on juvenile pollock from the postlarval period to the time they recruit to the fisheries. In addition to its importance to humans as a major commercial species, pollock also serves as a major forage species for many marine fishes, birds, and mammals in the North Pacific region. (PDF file contains 236 pages.)