Algorithm for simulating fracture processes in concrete by lattice modeling

To simulate fracture behaviors in concrete more realistically, a theoretical analysis on the potential question in the quasi-static method is presented, then a novel algorithm is proposed which takes into account the inertia effect due to unstable crack propagation and meanwhile requests much lower computational efforts than purely dynamic method. The inertia effect due to load increasing becomes less important and can be ignored with the loading rate decreasing, but the inertia effect due to unstable crack propagation remains considerable no matter how low the loading rate is. Therefore, results may become questionable if a fracture process including unstable cracking is simulated by the quasi-static procedure excluding completely inertia effects. However, it requires much higher computational effort to simulate experiments with not very high loading rates by the dynamic method. In this investigation which can be taken as a natural continuation, the potential question of quasi-static method is analyzed based on the dynamic equations of motion. One solution to this question is the new algorithm mentioned above. Numerical examples are provided by the generalized beam (GB) lattice model to show both fracture processes under different loading rates and capability of the new algorithm.

Numerical investigation of crack growth in concrete subjected to compression by the generalized beam lattice model

The beam lattice-type models, such as the Euler-Bernoulli (or Timoshenko) beam lattice and the generalized beam (GB) lattice, have been proved very effective in simulating failure processes in concrete and rock due to its simplicity and easy implementation. However, these existing lattice models only take into account tensile failures, so it may be not applicable to simulation of failure behaviors under compressive states. The main aim in this paper is to incorporate Mohr-Coulomb failure criterion, which is widely used in many kinds of materials, into the GB lattice procedure. The improved GB lattice procedure has the capability of modeling both element failures and contact/separation of cracked elements. The numerical examples show its effectiveness in simulating compressive failures. Furthermore, the influences of lateral confinement, friction angle, stiffness of loading platen, inclusion of aggregates on failure processes are respectively analyzed in detail.

Small-scale commercial production of tilapia fry and fingerlings in concrete raceways

This paper discusses the investment prospects in Tilapia fry and fingerling production in raceways created from the concrete drainage channel of a reservoir or pond of an existing fish farm in Nigeria. With an initial capital of 1,300 and an annual operating cost of 310 spent on procurement of fish feed and brood stock for a 10 m super(2) raceway per se, a net profit of 4,100 and 5,090 would be realized from Sarotherodon galilaeus in the first year and subsequent years of production respectively, assuming that the fingerling production rate has been maintained through the production period. It is concluded that the application of this approach of optimizing the use of available resources in the fish farm for the productive breeding of Tilapia fry and fingerlings will apart from alleviating the problem of scarcity of stocking materials in the country, increase the profit margin accruing to the fish farmer

Commercial production of Clarias fry and fingerlings in indoor and outdoor concrete tank systems

Induced breeding technique by hypophysation is being applied at the Kainji Lake Research Institute Fisheries Division Hatchery complex in New Bussa, Nigeria, for the production of Clarias fry and fingerlings in indoor and outdoor concrete tank systems. The hatchlings are fed on livefood (zooplankton) and artificial feed. Source of zooplankton is from cultured stock which is maintained throughout the breeding season by fertilization. Production values show that an average of over 4,000 hatchlings (larvae) can be produced by a female breeder (over-700g wt) and percentage survival after two months ranges between 70 to 75%. With the proposed modification and expansion project, an estimated production of over 0.5 million fingerlings per breeding season is projected

The variation of water quality in the outdoor concrete tank and earthen pond

The paper reports on the study carried out at the Federal College of Freshwater Fisheries and Technology (Nigeria) and the Hatchery Complex in 1997. The physico-chemical parameters of an earthen fish pond and concrete tank were analysed. The abundance and distribution of phytoplankton and zooplankton were recorded. A total of eight species of phytoplankton were observed. These species can be classified as Chlorophyceae (green algae), Bacillariophyceae (diatom algae) and Cyanophyta (blue-green algae). Eight zooplankton species were observed in the pond and 6 in the tank. Moina was observed and recorded as the most abundant cladoceran species in the tank

Effect of different feeding levels on the production of Heterobranchus bidorsalis in outdoor concrete tanks

Fry of Heterobranchus bidorsalis (mean weight, 0.03g) were fed at 10, 20, 30, 40 or 50% of their body weight (bw)/day in outdoor concrete tanks in New Bussa, Nigeria. The fry attained the highest average weight of 6.66g in 10 weeks when fed at 40% bw/day. Feed conversion ratio ranged from 2.13 to 9.65, the protein efficiency ratio from 1.33 to 5.93. Results indicated that H. bidorsalis are efficient feed converters. Feed intake was significantly different (p<0.05) between the treatments, specific growth rate (SGR), daily growth rate (DGR), production and average weight gain indicated that 40% of fish biomass was the optimum feeding level

Alignment of nanoparticles formed on the surface of 6H-SiC crystals irradiated by two collinear femtosecond laser beams

Nanoripples with periods of 150 and 80 nm are formed on the surface of 6H-SiC crystals irradiated by the p-polarized 800 nm and the s-polarized 400 nm femtosecond lasers, respectively. When both of the two collinear laser beams focus simultaneously on the sample surface, nanoparticles are formed on the whole ablation area, and they array in parallel lines. We propose and confirm that the second harmonics in the sample surface excited by the incident lasers plays an important role in the formation of nanostructures.