MOLECULAR MODELING OF EPON 862-DETDA / CARBON COMPOSITES

The thermoset epoxy resin EPON 862, coupled with the DETDA hardening agent, are utilized as the polymer matrix component in many graphite (carbon fiber) composites. Because it is difficult to experimentally characterize the interfacial region, computational molecular modeling is a necessary tool for understanding the influence of the interfacial molecular structure on bulk-level material properties. The purpose of this research is to investigate the many possible variables that may influence the interfacial structure and the effect they will have on the mechanical behavior of the bulk level composite. Molecular models are established for EPON 862-DETDA polymer in the presence of a graphite surface. Material characteristics such as polymer mass-density, residual stresses, and molecular potential energy are investigated near the polymer/fiber interface. Because the exact degree of crosslinking in these thermoset systems is not known, many different crosslink densities (degrees of curing) are investigated. It is determined that a region exists near the carbon fiber surface in which the polymer mass density is different than that of the bulk mass density. These surface effects extend ~10 Å into the polymer from the center of the outermost graphite layer. Early simulations predict polymer residual stress levels to be higher near the graphite surface. It is also seen that the molecular potential energy in polymer atoms decreases with increasing crosslink density. New models are then established in order to investigate the interface between EPON 862-DETDA polymer and graphene nanoplatelets (GNPs) of various atomic thicknesses. Mechanical properties are extracted from the models using Molecular Dynamics techniques. These properties are then implemented into micromechanics software that utilizes the generalized method of cells to create representations of macro-scale composites. Micromechanics models are created representing GNP doped epoxy with varying number of graphene layers and interfacial polymer crosslink densities. The initial micromechanics results for the GNP doped epoxy are then taken to represent the matrix component and are re-run through the micromechanics software with the addition of a carbon fiber to simulate a GNP doped epoxy/carbon fiber composite. Micromechanics results agree well with experimental data, and indicate GNPs of 1 to 2 atomic layers to be highly favorable. The effect of oxygen bonded to the surface of the GNPs is lastly investigated. Molecular Models are created for systems with varying graphene atomic thickness, along with different amounts of oxygen species attached to them. Models are created for graphene containing hydroxyl groups only, epoxide groups only, and a combination of epoxide and hydroxyl groups. Results show models of oxidized graphene to decrease in both tensile and shear modulus. Attaching only epoxide groups gives the best results for mechanical properties, though pristine graphene is still favored.

An Investigation of Waste Glass-Based Geopolymers Supplemented with Alumina

An increased consideration of sustainability throughout society has resulted in a surge of research investigating sustainable alternatives to existing construction materials. A new binder system, called a geopolymer, is being investigated to supplement ordinary portland cement (OPC) concrete, which has come under scrutiny because of the CO2 emissions inherent in its production. Geopolymers are produced from the alkali activation of a powdered aluminosilicate source by an alkaline solution, which results in a dense three-dimensional matrix of tetrahedrally linked aluminosilicates. Geopolymers have shown great potential as a building construction material, offering similar mechanical and durability properties to OPC. Additionally, geopolymers have the added value of a considerably smaller carbon footprint than OPC. This research considered the compressive strength, microstructure and composition of geopolymers made from two types of waste glass with varying aluminum contents. Waste glass shows great potential for mainstream use in geopolymers due to its chemical and physical homogeneity as well as its high content of amorphous silica, which could eliminate the need for sodium silicate. However, the lack of aluminum is thought to negatively affect the mechanical performance and alkali stability of the geopolymer system. Mortars were designed using various combinations of glass and metakaolin or fly ash to supplement the aluminum in the system. Mortar made from the high-Al glass (12% Al2O3) reached over 10,000 psi at six months. Mortar made from the low-Al glass (<1% Al2O3) did not perform as well and remained sticky even after several weeks of curing, most likely due to the lack of Al which is believed to cause hardening in geopolymers. A moderate metakaolin replacement (25-38% by mass) was found to positively affect the compressive strength of mortars made with either type of glass. Though the microstructure of the mortar was quite indicative of mechanical performance, composition was also found to be important. The initial stoichiometry of the bulk mixture was maintained fairly closely, especially in mixtures made with fine glass. This research has shown that glass has great potential for use in geopolymers, when care is given to consider the compositional and physical properties of the glass in mixture design.

Determing the Effect of Thermal Treatment Timing on Ultra-High Performance Concrete Beams

The loss of prestressing force over time influences the long-term deflection of the prestressed concrete element. Prestress losses are inherently complex due to the interaction of concrete creep, concrete shrinkage, and steel relaxation. Implementing advanced materials such as ultra-high performance concrete (UHPC) further complicates the estimation of prestress losses because of the changes in material models dependent on curing regime. Past research shows compressive creep is "locked in" when UHPC cylinders are subjected to thermal treatment before being loaded in compression. However, the current precasting manufacturing process would typically load the element (through prestressing strand release from the prestressing bed) before the element would be taken to the curing facility. Members of many ages are stored until curing could be applied to all of them at once. This research was conducted to determine the impact of variable curing times for UHPC on the prestress losses, and hence deflections. Three UHPC beams, a rectangular section, a modified bulb tee section, and a pi-girder, were assessed for losses and deflections using an incremental time step approach and material models specific to UHPC based on compressive creep and shrinkage testing. Results show that although it is important for prestressed UHPC beams to be thermally treated, to "lock in" material properties, the timing of thermal treatment leads to negligible differences in long-term deflections. Results also show that for UHPC elements that are thermally treated, changes in deflection are caused only by external loads because prestress losses are "locked-in" following thermal treatment.

Ecology of antimicrobial resistance: humans, animals, food and environment

Antimicrobial resistance is a major health problem. After decades of research, numerous difficulties in tackling resistance have emerged, from the paucity of new antimicrobials to the inefficient contingency plans to reduce the use of antimicrobials; consequently, resistance to these drugs is out of control. Today we know that bacteria from the environment are often at the very origin of the acquired resistance determinants found in hospitals worldwide. Here we define the genetic components that flow from the environment to pathogenic bacteria and thereby confer a quantum increase in resistance levels, as resistance units (RU). Environmental bacteria as well as microbiomes from humans, animals, and food represent an infinite reservoir of RU, which are based on genes that have had, or not, a resistance function in their original bacterial hosts. This brief review presents our current knowledge of antimicrobial resistance and its consequences, with special focus on the importance of an ecologic perspective of antimicrobial resistance. This discipline encompasses the study of the relationships of entities and events in the framework of curing and preventing disease, a definition that takes into account both microbial ecology and antimicrobial resistance. Understanding the flux of RU throughout the diverse ecosystems is crucial to assess, prevent and eventually predict emerging scaffolds before they colonize health institutions. Collaborative horizontal research scenarios should be envisaged and involve all actors working with humans, animals, food and the environment.

Garvicin A, a novel class IId bacteriocin from Lactococcus garvieae that inhibits septum formation in L. garvieae strains

Lactococcus garvieae 21881, isolated in a human clinical case, produces a novel class IId bacteriocin, garvicin A (GarA), which is specifically active against other L. garvieae strains, including fish- and bovine-pathogenic isolates. Purification from active supernatants, sequence analyses, and plasmid-curing experiments identified pGL5, one of the five plasmids found in L. garvieae [M. Aguado-Urda et al., PLoS One 7(6):e40119, 2012], as the coding plasmid for the structural gene of GarA (lgnA), its putative immunity protein (lgnI), and the ABC transporter and its accessory protein (lgnC and lgnD). Interestingly, pGL5-cured strains were still resistant to GarA. Other putative bacteriocins encoded by the remaining plasmids were not detected during purification, pointing to GarA as the main inhibitor secreted by L. garvieae 21881. Mode-of-action studies revealed a potent bactericidal activity of GarA. Moreover, transmission microscopy showed that GarA seems to act by inhibiting septum formation in L. garvieae cells. This potent and species-specific inhibition by GarA holds promise for applications in the prevention or treatment of infections caused by pathogenic strains of L. garvieae in both veterinary and clinical settings.

Effects of plasticizing and crosslinking on the mechanical and barrier properties of coatings based on blends of starch and poly(vinyl alcohol)

In the last decades, intensive research has been carried out in order to replace oil-based polymers with bio-based polymers due to growing environmental concerns. So far, most of the barrier materials used in food packaging are petroleum-based materials. The purpose of the barrier is to protect the packaged food from oxygen, water vapour, water and fat. The mechanical and barrier properties of coatings based on starch-plasticizer and starch-poly(vinyl alcohol) (PVOH)-plasticizer blends have been studied in the work described in this thesis. The plasticizers used were glycerol, polyethylene glycol and citric acid. In a second step, polyethylene coatings were extruded onto paperboard pre-coated with a starch-PVOH-plasticizer blend. The addition of PVOH to the starch increased the flexibility of the film. Curing of the film led to a decrease in flexibility and an increase in tensile strength. The flexibility of the starch-PVOH films was increased more when glycerol or polyethylene glycol was added than citric acid. The storage modulus of the starch-PVOH films containing citric acid increased substantially at high temperature. It was seen that the addition of polyethylene glycol or citric acid to the starch-PVOH blend resulted in an enrichment of PVOH at the surface of the films. Tensile tests on the films indicated that citric acid acted as a compatibilizer and increased the compatibility of the starch and PVOH in the blend. The addition of citric acid to the coating recipe substantially decreased the water vapour transmission rate through the starch-PVOH coated paperboard, which indicated that citric acid acts as a cross-linker for starch and/or PVOH. The starch-PVOH coatings containing citric acid showed oxygen-barrier properties similar to those of pure PVOH or of a starch-PVOH blend without plasticizer when four coating layers were applied on a paperboard. The oxygen-barrier properties of coatings based on a starch-PVOH blend containing citric acid indicated a cross-linking and increase in compatibility of the starch-PVOH blends. Polyethylene extrusion coating on a pre-coated paperboard resulted in a clear reduction in the oxygen transmission rate for all the pre-coating formulations containing plasticizers. The addition of a plasticizer to the pre-coating reduced the adhesion of polyethylene to pre-coated board. Polyethylene extrusion coating gave a board with a lower oxygen transmission rate when the paperboard was pre-coated with a polyethylene-glycol-containing formulation than with a citric-acid-containing formulation. The addition of polyethylene glycol to pre-coatings indicated an increase in wetting of the pre-coated paperboard by the polyethylene melt, and this may have sealed the small defects in the pre-coating leading to low oxygen transmission rate. The increase in brittleness of starch-PVOH films containing citric acid at a high temperature seemed to have a dominating effect on the barrier properties developed by the extrusion coating process. 

Influência de polímeros superabsorventes na retracção de argamassas

Hoje em dia, o desenvolvimento dos superplastificantes permite a produção de betões com menor razão água/cimento. Ao usar razões água/cimento mais baixas, os materiais científicos apresentam maior tendência para fissurar devido à retracção autogénea. Este trabalho apresenta um estudo sobre a utilização de polímeros superabsorventes (SAP) no controlo da retracção. O uso de SAPs em materiais comentícios atenua a retracção autogénea pois estes produtos permitem o fornecimento interno de água. Estes produtos podem também afectar outras propriedades, afectando as características mecânicas e a trabalhabilidade. Para análise do efeito dos SAP foram estudadas argamassas com várias concentrações deste produto, tendo como referência argamassas semelhantes sem SAP, determinando-se as retracções autogénea e total, a resistência à compressão e o módulo de elasticidade. Além de SAP, foi também utilizado um agregado leve, um outro tipo de introdutor de água, para comparação com os polímeros em estudo. /ABSTRACT: This work presents a study on the use of superabsorbent polymers (SAP) in the control of shrinkage. The use of SAPs in cementitious materials reduces the autogenous shrinkage because these products enable the internal supply of water. These materials can also affect other properties such as mechanical properties and workability. To analyze the effect of SAP, mortars containing various concentrations of this product were studied, in comparison with reference mortars without SAP. The tests performed were autogenous and total shrinkage, compressive strength and modulus of elasticity. Besides SAP, it was also used a lightweight aggregate, another type of internal supply of water, for comparison with the polymers under study.

Lacunae Infills for in Situ Treatment of Historic Glazed Tiles

Knowledge of current conservation materials and methods together with those adopted in the past is essential to aid research and improve or develop better conservation options. The infill and painting of tile lacunae are subjected to special requirements mainly when used in outdoor settings. A selection of the most commonly used materials was undertaken and performed based on inquiries to practitioners working in the field. The infill pastes comprised organic (epoxy, polyester), inorganic (slaked lime,hydraulic lime and zinc hydroxychloride) and mixed organic–inorganic (slaked lime mixed with a vinylic resin)binders. The selected aggregates were those most commonly used or those already present in the commercially formulated products. The infill pastes were characterised by SEM, MIP, open porosity, water absorption by capillarity, water vapour permeability, thermal and hydric expansibilities and adhesion to the ceramic body. Their performance was assessed after curing, artificial ageing (salt ageing and UV–Temp–RH cycles) and natural ageing. The results were interpreted in terms of their significance as indicators of effectiveness, compatibility and durability

Relação entre resistência ao cisalhamento no plano e parâmetros processuais de co-cura de juntas em compósitos auto-reforçados de polietileno de matriz reprocessada

Este estudo investiga a otimização da resistência ao cisalhamento no plano de juntas de sobreposição co-curadas do compósito termoplástico unidirecional auto-reforçado de polietileno de baixa densidade reciclado reforçado por fibras de polietileno de ultra alto peso molecular através da relação desta resistência com os parâmetros processuais de prensagem a quente para a conformação da junta (pressão, temperatura, tempo e comprimento). A matriz teve sua estrutura química analisada para verificar potenciais degradações devidas à sua origem de reciclagem. Matriz e reforço foram caracterizados termicamente para definir a janela de temperatura de processamento de junta a ser estudada. A elaboração das condições de cura dos corpos de prova foi feita de acordo com a metodologia de Projeto de Experimento de Superfície de Resposta e a relação entre a resistência ao cisalhamento das juntas e os respectivos parâmetros de cura foi obtida através de equação de regressão gerada pelo método dos Mínimos Quadrados Ordinários. A caracterização mecânica em tração do material foi analisada micro e macromecanicamente. A análise química da matriz não demonstrou a presença de grupos carboxílicos que evidenciassem degradação por ramificações de cadeia e reticulação advindos da reciclagem do material. As metodologias de ensaio propostas demonstraram ser eficazes, podendo servir como base para a constituição de normas técnicas. Demonstrou-se que é possível obter juntas com resistência ótima ao cisalhamento de 6,88 MPa quando processadas a 1 bar, 115°C, 5 min e com 12 mm. A análise da fratura revelou que a ruptura por cisalhamento das juntas foi precedida por múltiplas fissuras longitudinais induzidas por sucessivos debondings, tanto dentro quanto fora da junta, devido à tensão transversal acumulada na mesma, proporcional a seu comprimento. A temperatura demonstrou ser o parâmetro de processamento mais relevante para a performance da junta, a qual é pouco afetada por variações na pressão e tempo de cura.

Fibre naturali nel settore dei compositi: confronto fibre di lino vs. fibre di carbonio

I materiali compositi possiedono proprietà funzionali e di resistenza sempre più performanti grazie alla natura dei rinforzanti in fibra di carbonio, i quali però sono caratterizzati da criticità relative al processo di trasformazione altamente energivoro e dispendioso, all’inquinamento collegato alla produzione delle fibre e al trattamento di sizing, nonché alla difficoltà nello stadio di separazione dei costituenti del manufatto composito e del conseguente riciclo. A causa di queste problematiche sono stati introdotti in produzione materiali a matrice epossidica rinforzata con fibre di lino. Lo studio è stato indirizzato verso la caratterizzazione delle materie prime che compongono i manufatti, quindi fibre e semilavorati, mediante analisi termiche dinamiche in DSC e TGA con il fine di determinare la composizione e resistenza dei singoli componenti e la misura della variazione nel comportamento quando sono uniti per comporre i prepreg. Sono state eseguite delle prove di igroscopicità, umidità e densità per ottenere una panoramica precisa sulle differenze nella struttura delle fibre in carbonio e lino che le differenzia in modo apprezzabile. Sono stati laminati compositi reticolati secondo tecnologia in autoclave, le cui proprietà sono state definite mediante prove termiche dinamiche in DSC, TGA, DMA, prove alla fiamma mediante conocalorimetro, prove fisiche di igroscopicità, umidità e densità, prove ottiche al SEM in seguito ad una rottura in trazione. Parte del progetto seguito è stato direzionato all’ottimizzazione del ciclo produttivo in autoclave. La simulazione del nuovo ciclo di cura industriale, RAPID, è stata eseguita per valutare la variazione della Tg finale e il grado di curing, nonché le proprietà termiche e meccaniche già valutate nel ciclo di cura, STANDARD.

Damping and Thermomechanical behaviour of CFRP laminates modified with rubbery nanofibers

Nanofibrous membranes are a promising material for tailoring the properties of laminated CFRP composites by embedding them into the structure. This project aimed to understand the effect of number, position and thickness of nanofibrous modifications specifically on the damping behaviour of the resulting nano-modified CFRP composite with an epoxy matrix. An improvement of damping capacity is expected to improve a composites lifetime and fatigue resistance by prohibiting the formation of microcracks and consequently hindering delamination, it also promises a rise in comfort for a range of final products by intermission of vibration propagation and therefore diminution of noise. Electrospinning was the technique employed to produce nanofibrous membranes from a blend of polymeric solutions. SEM, WAXS and DSC were utilised to evaluate the quality of the obtained membranes before they were introduced, following a specific stacking sequence, in the production process of the laminate. A suitable curing cycle in an autoclave was applied to mend the modifications together with the matrix material, ensuring full crosslinking of the matrix and therefore finalising the production process. DMA was exercised in order to gain an understanding about the effects of the different modifications on the properties of the composite. During this investigation it became apparent that a high number of modifications of laminate CFRP composites, with an epoxy matrix, with thick rubbery nanofibrous membranes has a positive effect on the damping capacity and the temperature range the effect applies in. A suggestion for subsequent studies as well as a recommendation for the production of nano-modified CFRP structures is included at the end of this document.

The Virome of two Fusarium spp. Collections and its Potential for Controlling Fusarium Disease

This research aims to discover the virome diversity and composition in Fusarium poae and Fusarium proliferatum collections, characterize the mycovirus that may have an effect on host pathogenicity to provide potential materials for the biological control of Fusarium spp. pathogens. Next-Generation Sequencing (NGS) analysis of 30 F. poae isolates revealed an extreme diversity of mycoviruses. Bioinformatic analysis shows that contigs associated with viral genome belong to the families: Hypoviridae, Mitoviridae, Partitiviridae, Polymycoviridae, proposed Alternaviridae, proposed Fusagraviridae, proposed Fusariviridae, proposed Yadokariviridae, and Totiviridae. The complete genomes of 12 viruses were obtained by assembling contigs and overlapping cloning sequences. Moreover, all the F. poae isolates analyzed are multi-infected. Fusarium poae partitivirus 1 appears in all the 30 strains, followed by Fusarium poae fusagravirus 1 (22), Fusarium poae mitovirus 2 (18), Fusarium poae partitivirus 3 (16), and Fusarium poae mitovirus 2 and 3 (11). Using the same approach, the virome of F. proliferatum collections resulted in lower diversity and abundance. The identified mycoviruses belong to the family Mitoviridae and Mymonaviridae. Interestingly, most F. proliferatum isolates are not multi-infected. The complete genomes of four viruses were obtained by assembling contigs and overlapping cloning sequences. By multiple liner regression of the virome composition and growth rate of 30 F. poae, Fusarium poae mitovirus 3 is significantly correlated with the growth rate among F. poae collection. Furthermore, the principal component analysis of the virome composition from 30 F. poae showed that the presence of Fusarium poae mitovirus 3 and other two viruses could increase the F. poae growth rate. The curing experiment and pathogenicity test in Petri indicated that Fusarium poae hypovirus 1 might be associated with the host hypovirulence phenotype, while Fusarium poae fusagravirus 1 and Fusarium poae partitivirus 3 may have some beneficial effect on host pathogenicity.

Theoretical and experimental study of novel hybrid composite and metal-composites interfaces

The growing demand for lightweight solutions in every field of engineering is driving the industry to seek new technological solutions to exploit the full potential of different materials. The combination of dissimilar materials with distinct property ranges embodies a transparent allocation of component functions while allowing an optimal mix of their characteristics. From both technological and design perspectives, the interaction between dissimilar materials can lead to severe defects that compromise a multi-material hybrid component's performance and its structural integrity. This thesis aims to develop methodologies for designing, manufacturing, and monitoring of hybrid metal-composite joints and hybrid composite components. In Chapter 1, a methodology for designing and manufacturing hybrid aluminum/composite co-cured tubes is assessed. In Chapter 2, a full-field methodology for fiber misalignment detection and stiffness prediction for hybrid, long fiber reinforced composite systems is shown and demonstrated. Chapter 3 reports the development of a novel technology for joining short fiber systems and metals in a one-step co-curing process using lattice structures. Chapter 4 is dedicated to a novel analytical framework for the design optimization of two lattice architectures.

Development and characterization of innovative graphene-based composites

Over the last decade, graphene and related materials (GRM) have drawn significant interest and resources for their development into the next generation of composite materials. This is because these nanoparticles have the ability to operate as reinforcing additives capable of imparting considerable mechanical property increases while also embedding multi-functional advantages on the host matrix. Because graphene and 2D materials are still in their early stages, the relative maturity of different types of composite systems varies. As a result, certain nanocomposite systems are currently commercially accessible, while others are not yet sufficiently developed to enter the market. A substantial emphasis has been placed on developing thermoplastic and thermosetting materials that combine a variety of mechanical and functional qualities. These include higher strength and stiffness, increased thermal and electrical conductivity, improved barrier properties, fire retardancy, and others, with the ultimate goal of providing multifunctionality to already employed composites. The work presented in this thesis investigates the use and benefits that GRM could bring to composites for a variety of applications, with the goal of realizing multifunctional components with improved properties that leads to lightweight and, as a result, energy and cost savings and pollution reduction in the environment. In particular, we worked on the following topics: • Benchmarking of commercial GRM-based master batches; • GRM-coatings for water uptake reduction; • GRM as thermo-electrical anti-icing /de-icing system; • GRM for Out of Oven curing of composites.

Mechanical behaviour and durability assessment of Fibre Reinforced Cementitious Matrix (FRCM) strengthening systems.

In recent years, the seismic vulnerability of existing masonry buildings has been underscored by the destructive impacts of earthquakes. Therefore, Fibre Reinforced Cementitious Matrix (FRCM) retrofitting systems have gained prominence due to their high strength-to-weight ratio, compatibility with substrates, and potential reversibility. However, concerns linger regarding the durability of these systems when subjected to long-term environmental conditions. This doctoral dissertation addressed these concerns by studying the effects of mild temperature variations on three FRCM systems, featuring basalt, glass, and aramid fibre textiles with lime-based mortar matrices. The study subjected various specimens, including mortar triplets, bare textile specimens, FRCM coupons, and single-lap direct shear wallets, to thermal exposure. A novel approach utilizing embedded thermocouple sensors facilitated efficient monitoring and active control of the conditioning process. A shift in the failure modes was obtained in the single lap-direct shear tests, alongside a significant impact on tensile capacity for both textiles and FRCM coupons. Subsequently, bond tests results were used to indirectly calibrate an analytical approach based on mode-II fracture mechanics. A comparison between Cohesive Material Law (CML) functions at various temperatures was conducted for each of the three systems, demonstrating a good agreement between the analytical model and experimental curves. Furthermore, the durability in alkaline environment of two additional FRCM systems, characterized by basalt and glass fibre textiles with lime-based mortars, was studied through an extensive experimental campaign. Tests conducted on single yarn and textile specimens after exposure at different durations and temperatures revealed a significant impact on tensile capacity. Additionally, FRCM coupons manufactured with conditioned textile were tested to understand the influence of aged textile and curing environment on the final tensile behavior. These results contributed significantly to the existing knowledge on FRCM systems and could be used to develop a standardized alkaline testing protocol, still lacking in the scientific literature.