Measurement of the W gamma and Z gamma inclusive cross sections in pp collisions at root s=7 TeV and limits on anomalous triple gauge boson couplings

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Measurement of Inclusive W and Z Boson Production Cross Sections in pp Collisions at root s=8 TeV

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Search for supersymmetry in pp collisions at root s=8 TeV in events with a single lepton, large jet multiplicity, and multiple b jets

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Measurement of associated W plus charm production in pp collisions at root s=7 TeV

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Evidence for the 125 GeV Higgs boson decaying to a pair of tau leptons

A search for a standard model Higgs boson decaying into a pair of tau leptons is performed using events recorded by the CMS experiment at the LHC in 2011 and 2012. The dataset corresponds to an integrated luminosity of 4.9 fb(-1) at a centre-of-mass energy of 7 TeV and 19.7 fb(-1) at 8 TeV. Each tau lepton decays hadronically or leptonically to an electron or a muon, leading to six different final states for the tau-lepton pair, all considered in this analysis. An excess of events is observed over the expected background contributions, with a local significance larger than 3 standard deviations for m (H) values between 115 and 130 GeV. The best fit of the observed H -> tau tau signal cross section times branching fraction for m(H) = 125 GeV is 0.78 +/- 0.27 times the standard model expectation. These observations constitute evidence for the 125 GeV Higgs boson decaying to a pair of tau leptons.

Measurement of the t-channel single-top-quark production cross section and of the |V (tb)| CKM matrix element in pp collisions at root s=8 TeV

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Search for pair production of excited top quarks in the lepton plus jets final state

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Structural, electronic and optical properties of Fe(III) complex with pyridine-2,6-dicarboxylic acid: A combined experimental and theoretical study

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Measurement of the p(p)over-bar -> W plus b plus X production cross section at root s=1.96 TeV D0 Collaboration

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Time reduction of light curing: Influence on conversion degree and microhardness of orthodontic composites

Introduction: The aim of this study was to assess the influence of curing time and power on the degree of conversion and surface microhardness of 3 orthodontic composites. Methods: One hundred eighty discs, 6 mm in diameter, were divided into 3 groups of 60 samples according to the composite used-Transbond XT (3M Unitek, Monrovia, Calif), Opal Bond MV (Ultradent, South Jordan, Utah), and Transbond Plus Color Change (3M Unitek)-and each group was further divided into 3 subgroups (n = 20). Five samples were used to measure conversion, and 15 were used to measure microhardness. A light-emitting diode curing unit with multiwavelength emission of broad light was used for curing at 3 power levels (530, 760, and 1520 mW) and 3 times (8.5, 6, and 3 seconds), always totaling 4.56 joules. Five specimens from each subgroup were ground and mixed with potassium bromide to produce 8-mm tablets to be compared with 5 others made similarly with the respective noncured composite. These were placed into a spectrometer, and software was used for analysis. A microhardness tester was used to take Knoop hardness (KHN) measurements in 15 discs of each subgroup. The data were analyzed with 2 analysis of variance tests at 2 levels. Results: Differences were found in the conversion degree of the composites cured at different times and powers (P < 0.01). The composites showed similar degrees of conversion when light cured at 8.5 seconds (80.7%) and 6 seconds (79.0%), but not at 3 seconds (75.0%). The conversion degrees of the composites were different, with group 3 (87.2%) higher than group 2 (83.5%), which was higher than group 1 (64.0%). Differences in microhardness were also found (P < 0.01), with lower microhardness at 8.5 seconds (35.2 KHN), but no difference was observed between 6 seconds (41.6 KHN) and 3 seconds (42.8 KHN). Group 3 had the highest surface microhardness (35.9 KHN) compared with group 2 (33.7 KHN) and group 1 (30.0 KHN). Conclusions: Curing time can be reduced up to 6 seconds by increasing the power, with a slight decrease in the degree of conversion at 3 seconds; the decrease has a positive effect on the surface microhardness.

Direct Spectrometry: A New Alternative for Measuring the Fluorescence of Composite Resins and Dental Tissues

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Real-time monitoring of ozone in air using substrate-integrated hollow waveguide mid-infrared sensors

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Monitoring of hydrogen sulfide via substrate-integrated hollow waveguide mid-infrared sensors in real-time

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

ANTIDIARRHEAL MECHANISM AND IONIC PROFILE OF CARPOLOBIA LUTEA ETHANOLIC STEM-BARK EXTRACT IN RATS

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Production of the Quinone-Methide Triterpene Maytenin by In Vitro Adventitious Roots of Peritassa campestris (Cambess.) ACSm. (Celastraceae) and Rapid Detection and Identification by APCI-IT-MS/MS

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)