Screening process for activity determination of conductive oxide electrodes for organic oxidation

A modified method for the calculation of the normalized faradaic charge (q fN) is proposed. The method involves the simulation of an oxidation process, by cyclic voltammetry, by employing potentials in the oxygen evolution reaction region. The method is applicable to organic species whose oxidation is not manifested by a defined oxidation peak at conductive oxide electrodes. The variation of q fN for electrodes of nominal composition Ti/RuX Sn1-X O2 (x = 0.3, 0.2 and 0.1), Ti/Ir0.3Ti0.7O2 and Ti/Ru0.3Ti0.7O2 in the presence of various concentrations of formaldehyde was analyzed. It was observed that electrodes containing SnO2 are the most active for formaldehyde oxidation. Subsequently, in order to test the validity of the proposed model, galvanostatic electrolyses (40 mA cm-2) of two different formaldehyde concentrations (0.10 and 0.01 mol dm-3) were performed. The results are in agreement with the proposed model and indicate that this new method can be used to determine the relative activity of conductive oxide electrodes. In agreement with previous studies, it can be concluded that not only the nature of the electrode material, but also the organic species in solution and its concentration are important factors to be considered in the oxidation of organic compounds.

Spectroscopic characterization and investigation of the dynamic of charge compensation process of supramolecular films derived from tetra-2-pyridyl-1,4-pyrazine ligand

This work describes the infrared spectroscopy characterization and the charge compensation dynamics in supramolecular film FeTPPZFeCN derived from tetra-2-pyridyl-1,4-pyrazine (TPPZ) with hexacyanoferrate, as well as the hybrid film formed by FeTPPZFeCN and polypyrrole (PPy). For supramolecular film, it was found that anion flux is greater in a K+ containing solution than in Li+ solution, which seems to be due to the larger crystalline ionic radius of K+. The electroneutralization process is discussed in terms of electrostatic interactions between cations and metallic centers in the hosting matrix. The nature of the charge compensation process differs from others modified electrodes based on Prussian blue films, where only cations such as K+ participate in the electroneutralization process. In the case of FeTPPZFeCN/PPy hybrid film, the magnitude of the anions’s flux is also dependent on the identity of the anion of the supporting electrolyte.

Impacto da adequação da oferta energética sobre a mortalidade em pacientes de UTI recebendo nutrição enteral

OBJETIVO: Investigar a relação entre adequação da oferta energética e mortalidade na unidade de terapia intensiva em pacientes sob terapia nutricional enteral exclusiva. MÉTODOS: Estudo observacional prospectivo conduzido em uma unidade de terapia intensiva em 2008 e 2009. Foram incluídos pacientes >18 anos que receberam terapia nutricional enteral por >72h. A adequação da oferta de energia foi estimada pela razão administrado/prescrito. Para a investigação da relação entre variáveis preditoras (adequação da oferta energética, escore APACHE II, sexo, idade e tempo de permanência na unidade de terapia intensiva e o desfecho mortalidade na unidade de terapia intensiva, utilizou-se o modelo de regressão logística não condicional. RESULTADOS: Foram incluídos 63 pacientes (média 58 anos, mortalidade 27%), 47,6% dos quais receberam mais de 90% da energia prescrita (adequação média 88,2%). O balanço energético médio foi de -190 kcal/dia. Observou-se associação significativa entre ocorrência de óbito e as variáveis idade e tempo de permanência na unidade de terapia intensiva, após a retirada das variáveis adequação da oferta energética, APACHE II e sexo durante o processo de modelagem. CONCLUSÃO: A adequação da oferta energética não influenciou a taxa de mortalidade na unidade de terapia intensiva. Protocolos de infusão de nutrição enteral seguidos criteriosamente, com adequação administrado/prescrito acima de 70%, parecem ser suficientes para não interferirem na mortalidade. Dessa forma, pode-se questionar a obrigatoriedade de atingir índices próximos a 100%, considerando a elevada frequência com que ocorrem interrupções no fornecimento de dieta enteral devido a intolerância gastrointestinal e jejuns para exames e procedimentos. Pesquisas futuras poderão identificar a meta ideal de adequação da oferta energética que resulte em redução significativa de complicações, mortalidade e custos.

Vinculação determinística de Bancos de Dados sobre mortalidade por Aids

A vinculação determinística de bancos de dados sobre mortalidade por aids tem apresentado problemas causados por falhas nos arquivos. Assim, os objetivos deste estudo foram: avaliar o desempenho da vinculação determinística em bancos de óbito por aids do Programa de Aprimoramento das Informações de Mortalidade no Município de São Paulo (PRO-AIM) e da Fundação SEADE entre os anos de 2000 e 2004 e estimar a cobertura de cada banco. Utilizou-se a rotina merge de um software para vincular os bancos. A primeira etapa pareou os registros automaticamente e, na segunda etapa, cada banco foi conferido para localizar novos pares. Estimaram-se os óbitos pela soma entre casos pareados e não pareados para calcular a cobertura dos bancos. A primeira etapa da vinculação identificou 91,6% dos pares. A segunda etapa adicionou 457 pares. O total de óbitos foi estimado em 5.855, com cobertura de 97,1% do PRO-AIM e 96% do SEADE. O uso da vinculação determinística cobriu grande parte dos casos. O banco do PRO-AIM proporcionou a maior cobertura, com maior quantidade de informações completas e melhor localização geográfica dos casos.

Circuitos de uso de crack na região central da cidade de São Paulo (SP, Brasil)

Apesar de o uso de drogas ser uma prática presente desde os primórdios da humanidade, atualmente o seu abuso adquiriu dimensões preocupantes, configurando-se como um problema de saúde pública. O surgimento do crack, droga derivada da pasta de coca, agravou esse quadro ao aumentar os danos sociais e à saúde dos usuários. Visando conhecer o impacto de sua inserção no cotidiano dos usuários, foi realizado um estudo etnográfico em locais de venda e uso de crack na região central da cidade de São Paulo (SP, Brasil). Foi utilizado um diário de campo para registrar as observações e os diálogos informais efetuados com as pessoas que circulavam no local estudado. Os resultados apontaram os circuitos percorridos pelos usuários, suas dinâmicas e as relações que estabelecem com outros atores sociais, as quais são permeadas por permanente tensão, envolvendo a prática de atos violentos nos quais os usuários são tanto agressores quanto vítimas. O estudo também sugere a importância de outros fatores como a história da região pesquisada, as políticas públicas, questões econômicas e ausência de investimentos sociais e em saúde pública. Sugere-se que o alto grau de degradação da região pesquisada não seria consequência apenas das pessoas e atividades exercidas no local, mas principalmente do processo urbano que gerou tal quadro social.

Modelagem e gestão das perdas no suprimento de tomates para processamento industrial

O suprimento de tomates para processamento industrial é uma atividade relativamente complexa. Plantas industriais de larga escala necessitam de elevados volumes diários de matéria-prima. Por outro lado, há alta perecibilidade dos frutos e a colheita ainda é predominantemente manual. Um modelo matemático foi desenvolvido com o propósito de entender objetivamente o processo de suprimento de tomate e, também, vislumbrar possibilidades de sua otimização. A simulação a partir do modelo pode gerar cenários que, quando comparados com o desempenho efetivamente observado em campo, evidenciam a importância da gestão acurada, com a presença de potenciais ganhos financeiros expressivos na cadeia de suprimentos a partir da redução de tempos, perdas e custos. As perdas de produto poderiam ser reduzidas de mais de 2% para algo inferior a 1%. A menor capacidade ociosa traduzir-se-ia em um menor custo de oportunidade e aumento de receita. Para uma fábrica com um consumo de tomates de 336 mil toneladas por ano, a melhoria no suprimento de matéria-prima poderia resultar em ganhos estimados em R$ 6 milhões por ano.

Body Mass Index, Cigarette Smoking, and Alcohol Consumption and Cancers of the Oral Cavity, Pharynx, and Larynx: Modeling Odds Ratios in Pooled Case-Control Data

study-specific results, their findings should be interpreted with caution

The Process of Simulation Authoring/Creation by Chemistry Teachers: A Service Learning Experience

Two case studies are presented to describe the process of public school teachers authoring and creating chemistry simulations. They are part of the Virtual Didactic Laboratory for Chemistry, a project developed by the School of the Future of the University of Sao Paulo. the documental analysis of the material produced by two groups of teachers reflects different selection process for both themes and problem-situations when creating simulations. The study demonstrates the potential for chemistry learning with an approach that takes students' everyday lives into account and is based on collaborative work among teachers and researches. Also, from the teachers' perspectives, the possibilities of interaction that a simulation offers for classroom activities are considered.

Spectral Region Optimization for Raman-Based Optical Biopsy of Inflammatory Lesions

Objective: The biochemical alterations between inflammatory fibrous hyperplasia (IFH) and normal tissues of buccal mucosa were probed by using the FT-Raman spectroscopy technique. The aim was to find the minimal set of Raman bands that would furnish the best discrimination. Background: Raman-based optical biopsy is a widely recognized potential technique for noninvasive real-time diagnosis. However, few studies had been devoted to the discrimination of very common subtle or early pathologic states as inflammatory processes that are always present on, for example, cancer lesion borders. Methods: Seventy spectra of IFH from 14 patients were compared with 30 spectra of normal tissues from six patients. The statistical analysis was performed with principal components analysis and soft independent modeling class analogy cross-validated, leave-one-out methods. Results: Bands close to 574, 1,100, 1,250 to 1,350, and 1,500 cm(-1) (mainly amino acids and collagen bands) showed the main intragroup variations that are due to the acanthosis process in the IFH epithelium. The 1,200 (C-C aromatic/DNA), 1,350 (CH(2) bending/collagen 1), and 1,730 cm(-1) (collagen III) regions presented the main intergroup variations. This finding was interpreted as originating in an extracellular matrix-degeneration process occurring in the inflammatory tissues. The statistical analysis results indicated that the best discrimination capability (sensitivity of 95% and specificity of 100%) was found by using the 530-580 cm(-1) spectral region. Conclusions: The existence of this narrow spectral window enabling normal and inflammatory diagnosis also had useful implications for an in vivo dispersive Raman setup for clinical applications.

Architecture for machining process and production monitoring based in open computer numerical control

This paper proposes an architecture for machining process and production monitoring to be applied in machine tools with open Computer numerical control (CNC). A brief description of the advantages of using open CNC for machining process and production monitoring is presented with an emphasis on the CNC architecture using a personal computer (PC)-based human-machine interface. The proposed architecture uses the CNC data and sensors to gather information about the machining process and production. It allows the development of different levels of monitoring systems with mininium investment, minimum need for sensor installation, and low intrusiveness to the process. Successful examples of the utilization of this architecture in a laboratory environment are briefly described. As a Conclusion, it is shown that a wide range of monitoring solutions can be implemented in production processes using the proposed architecture.

Bond Strength of Multicomponent White Cast Iron Coatings Applied by HVOF Thermal Spray Process

Multicomponent white cast iron is a new alloy that belongs to system Fe-C-Cr-W-Mo-V, and because of its excellent wear resistance it is used in the manufacture of hot rolling mills rolls. To date, this alloy has been processed by casting, powder metallurgy, and spray forming. The high-velocity oxyfuel process is now also considered for the manufacture of components with this alloy. The effects of substrate, preheating temperature, and coating thickness on bond strength of coatings have been determined. Substrates of AISI 1020 steel and of cast iron with preheating of 150 A degrees C and at room temperature were used to apply coatings with 200 and 400 mu m nominal thickness. The bond strength of coatings was measured with the pull-off test method and the failure mode by scanning electron microscopic analysis. Coatings with thickness of 200 mu m and applied on substrates of AISI 1020 steel with preheating presented bond strength of 87 +/- A 4 MPa.

Modeling of the Barkhausen jump in low carbon steel

This work presents a model for the magnetic Barkhausen jump in low carbon content steels. The outcomes of the model evidence that the Barkhausen jump height depends on the coercive field of the pinning site and on the mean free path of the domain wall between pinning sites. These results are used to deduce the influence of the microstructural features and of the magnetizing parameters on the amplitude and duration of the Barkhausen jumps. In particular, a theoretical expression, establishing the dependence of the Barkbausen jump height on the carbon content and grain size, is obtained. The model also reveals the dependence of the Barkhausen jump on the applied frequency and amplitude. Theoretical and experimental results are presented and compared, being in good agreement. (C) 2008 American Institute of Physics.

Importance of considering a material micro-failure criterion in the numerical modelling of the shot peening process applied to parabolic leaf springs

Shot peening is a cold-working mechanical process in which a shot stream is propelled against a component surface. Its purpose is to introduce compressive residual stresses on component surfaces for increasing the fatigue resistance. This process is widely applied in springs due to the cyclical loads requirements. This paper presents a numerical modelling of shot peening process using the finite element method. The results are compared with experimental measurements of the residual stresses, obtained by the X-rays diffraction technique, in leaf springs submitted to this process. Furthermore, the results are compared with empirical and numerical correlations developed by other authors.

AVERAGE CONTINUOUS CONTROL OF PIECEWISE DETERMINISTIC MARKOV PROCESSES

This paper deals with the long run average continuous control problem of piecewise deterministic Markov processes (PDMPs) taking values in a general Borel space and with compact action space depending on the state variable. The control variable acts on the jump rate and transition measure of the PDMP, and the running and boundary costs are assumed to be positive but not necessarily bounded. Our first main result is to obtain an optimality equation for the long run average cost in terms of a discrete-time optimality equation related to the embedded Markov chain given by the postjump location of the PDMP. Our second main result guarantees the existence of a feedback measurable selector for the discrete-time optimality equation by establishing a connection between this equation and an integro-differential equation. Our final main result is to obtain some sufficient conditions for the existence of a solution for a discrete-time optimality inequality and an ordinary optimal feedback control for the long run average cost using the so-called vanishing discount approach. Two examples are presented illustrating the possible applications of the results developed in the paper.

Intrinsic colony conditions affect the provisioning and oviposition process in the stingless bee Melipona scutellaris

The cell provisioning and oviposition process (POP) is a unique characteristic of stingless bees (Meliponini), in which coordinated interactions between workers and queen regulate the filling of brood cells with larval resources and subsequent egg laying. Environmental conditions seem to regulate reproduction in stingless bees; however, little is known about how the amount of food affects quantitative sequences of the process. We examined intrinsic variables by comparing three colonies in distinct conditions (strong, intermediate and weak state). We predicted that some of these variables are correlated with temporal events of POP in Melipona scutellaris colonies. The results demonstrated that the strong colony had shorter periods of POP.