Desenvolvimento de argamassa para restauração utilizando resíduo do polimento do porcelanato

The coatings mortars are essential elements of building structures because they execute an important role in protecting walls and are particularly exposed to aggressive action responsible for its degradation over time. The importance of wall coverings has been the subject of discussion and analysis in the conservation and rehabilitation of old buildings. Are sometimes removed and replaced with inappropriate solutions of constructive point of view or architecture. The most commonly used coatings on walls of old buildings is based on traditional hydraulic lime mortars. The present study aims at the formulation of new lime- based mortars and aerial fine aggregate, in order to contribute to a better field of conservation and restoration mortar coating of old buildings. Residue was used for polishing porcelain as fine aggregate, replacing the aggregate (sand), in percentages 05-30% by mass. We conducted a thorough evaluation of the mortar properties in fresh and hardened state by comparing the performance of the same with a reference mortar. The residue used was characterized as the density, bulk density, and particle size laser, scanning electron microscopy, X-ray diffraction and X-ray fluorescence. Formulations were produced 7, 6 with residue and one commonly used formulation, which served as a reference. In the formulations of lime mortars air (hydrated lime powder CH-I) has been adopted a stroke volume (1:3) with constant binder, was varied and the water / binder and aggregate and waste. For evaluation of mortars fresh, proceeded to consistency analysis, specific gravity, water retention and air content embedded. In the hardened state assays were performed in specific gravity, water retention, modulus of elasticity, tensile strength in bending, compressive strength, water absorption by capillary action, adhesion, tensile strength, resistance to shrinkage and salts by of crystallization trials with resources chloride solution, nitrate and sulfate all sodium in prismatic at 90 days of age, in addition to the micro structural analysis of mortars. Based on the results we can see that the mortar formulated with 10% content of waste and the reference free retraction feature more stable closer to neutrality. The composition of 10% was obtained better performance against the action of the salt crystallization. The mortar with 15% residue obtained better density, lower air content embedded and high capacity for water retention developing good workability. The replacement of 20% of waste generates a satisfactory utilization of resistance to compression, flexion and traction grip the base. And, finally, it can be seen that the mortar with 10, 15 and 20% residual show, in principle, good suitability as coatings, thus enabling a final result consistent with durability, workability and aesthetics developing therefore a material with better performance to repair or replace existing mortars in old buildings

Optimización del pelado de maíz con cal a utilizarse como estrategia de descontaminación de fumonisinas

Objetivo: En este estudio, el proceso de pelado de maíz con cal(PPC) fue documentado y sus parámetros optimizados mediante un diseño experimental, con el fin de conseguir un pelado completo del maíz con el mínimo grado de contaminación con fumonisinas. La presencia de fumonisina B1 (FB1) en el maíz fue analizada mediante HPLC-RP-FLD. Metodología: Los experimentos se realizaron a partir de un lote de maíz en grano seco conformado por submuestras provistas por agricultores seleccionados del cantón Nabón de la provincia del Azuay en base a un trabajo de investigación previo realizado por el proyecto VLIR-IUC, “Nutrición, Alimentación y Salud”. El diseño experimental fue divido en tres etapas: la caracterización de proceso, el mismo que se realizó mediante encuestas y observaciones in situ; pruebas de agotamiento de cal para el PPC, las que se realizaron partiendo de los datos recogidos en la primera etapa, y las pruebas de evaluación del PPC en la reducción de fumonisinas B1. Resultados y conclusiones: Se observó que, independiente de la concentración de cal utilizada, la etapa de pelado produjo una reducción de 8.73 veces la concentración de FB1 del maíz crudo (P=0.030), y que el maíz pelado y cocinado presentó una reducción de 9.14 veces (P=0.019). Recomendaciones: Se recomienda continuar con la experimentación para elucidar si la reducción de FB1se debió al proceso mecánico de remoción de la cáscara, o a la transformación química en su forma hidrolizada, por lo que este trabajo podría considerarse como un estudio explorativo preliminar.

Impact of HydroPolymers on the soil biological components in mediterranean drylands

Soil degradation affects more than 52 million ha of land in counties of the European Union. This problem is particularly serious in Mediterranean areas, where the effects of anthropogenic activities (tillage on slopes, deforestation, and pasture production) add to problems caused by prolonged periods of drought and intense and irregular rainfall. Soil microbiota can be used as an indicator of the soil healthy in degraded areas. This is because soil microbiota participates in the cycle elements and in the organic matter decomposition. All this helps to the young plants establishment and in long term protect the soils against the erosion. During dry periods in the Mediterranean areas, the lack of water entering the soil matrix leads to a loss of soil microbiological activity and it turns into a lower soil production capabilities. Under these conditions, the aim of this study was to evaluate the positive effect on soil biological components produced by an hydro absorbent polymer (Terracottem). The aim of the experiment was to evaluate the impact assessment of an hydropolymer (Terracottem) on the soil biological components. An experimental flowerpot layout was established in June 2015 and 12 variants with different amount of Terracottem were applied as follow: i) 3.0 kg.m3 ; ii) 1.5 kg.m3 and; iii) 0 kg.m3. In all the variants were tested the further additives: a) 1% of glucose, b) 50 kg N.ha-1 of Mineral nitrogen, c) 1% of Glucose + 50 kg N.ha-1 of Mineral nitrogen d) control (no additive). According to natural conditions, humidity have been kept at 15% in all the variants. During four weeks, mineral nitrogen leaching and soil respiration have been measured in each flowerplot. Respiration has been quantified four times every time while moistening containers and alkaline soda lime has been used as a sorbent. The amount of CO 2 increase has been measured with the sorbent. Leaching of mineral nitrogen has been quantified by ion exchange resins (IER). IER pouches have been placed on the bottom of each container, and after completion of the experiment mineral nitrogen leaching has been evaluated by distillation and titration method. Results from respiration have shown statistically significant differences between the variants. According to control, soil with polymers have shown significant difference when comparing respiration with independence of the additive used. CO 2 production in the first week has exceeded the sum of the outputs of the following weeks. Mineral nitrogen leaching measurement has shown statistically significant differences. The lowest leaching has been occurred in control variant, while the highest in variant containing only the addition of mineral nitrogen. Research results may conclude that the biological part of the test soil is not limited by a lack of components, the only thing that suppresses its activity is the lack of moisture. After moistening it leads to a rapid growth of soil activity, without causing the nutrients loss. Besides, Terracottem has affected soil activity neither positively nor negatively, but it considers being a suitable tool for reducing the drought impact in arid and semi-arid areas.

Influência da adição de cinza do bagaço de cana calcinada em sistemas de pastas para cimentação de poços petrolíferos

Cementing operation is one of the most important stages in the oil well drilling processes and has main function to form hydraulic seal between the various permeable zones traversed by the well. However, several problems may occur with the cement sheath, either during primary cementing or during the well production period. Cements low resistance can cause fissures in the cement sheath and compromise the mechanical integrity of the annular, resulting in contamination of groundwater and producing zones. Several researches show that biomass ash, in particular, those generated by the sugarcane industry have pozzolanic activity and can be added in the composition of the cementing slurries in diverse applications, providing improvements in mechanical properties, revenue and cement durability. Due to the importance of a low cost additive that increases the mechanical properties in a well cementing operations, this study aimed to potentiate the use of sugarcane bagasse ash as pozzolanic material, evaluate the mechanisms of action of this one on cement pastes properties and apply this material in systems slurries aimed to cementing a well with 800 m depth and geothermal gradient of 1.7 °F/100 ft, as much primary cementing operations as squeeze. To do this, the ash beneficiation methods were realized through the processes of grinding, sifting and reburning (calcination) and then characterization by X-ray fluorescence, XRD, TG / DTG, specific surface area, particle size distribution by laser diffraction and mass specific. Moreover, the ash pozzolanic activity added to the cement at concentrations of 0%, 20% and 40% BWOC was evaluated by pozzolanic activity index with lime and with Portland cement. The evaluation of the pozzolanic activity by XRD, TG / DTG and compressive strength confirmed the ash reactivity and indicated that the addition of 20% in the composition of cement slurries produces improvement 34% in the mechanical properties of the slurry cured. Cement slurries properties evaluated by rheological measurements, fluid loss, free fluid, slurry sedimentation, thickening time and sonic strength (UCA) were satisfactory and showed the viability of using the sugarcane ash in cement slurries composition for well cementing

Cement-Wood composites: effects of wood species, particle treatments and mix proportion

The aim of this research was to investigate the effects of wood species, particle treatments and mix proportion on the physical (density) and mechanical (compressive strength and dynamicmodulus of elasticity) properties of cement-wood composites. Different mix proportions were investigated, based on the cement: wood ratio of 0.3:0.7, in volume, with Pinus elliottii and Eucalyptus grandis sawdust percentages of 0-100, 25-75, 50-50, 75-25 or 100-0. Sawdust particles were pre-treated with either lime or cement coating to improve cement and wood compatibility. Results show that wood species, particle treatments and mix proportions may influence the physical and mechanical properties of cement-wood composites. In general, results confirm that Eucalyptus sawdust and cement are naturally compatible and do not require any previous particle treatment to avoid compatibility problems.

Arsenic Geochemitry in Warm Spring Ponds: New Field and Experimental Results

Silver Bow Creek (SBC) flows into the Warm Springs Ponds Operable Unit (WSPOU), where various containment cells are used to precipitate copper and other metals (e.g., Cd, Cu, Mn, Pb, Zn). Lime is added seasonally to increase the pH and assist in removal of metals from the water column. Although the WSPOU is effective at removing copper and other cationic trace metals, concentrations of dissolved arsenic exiting the facility are often above the site specific standard, 20 20 ug/L, during low-flow periods each summer and fall. This thesis is a continuation of arsenic geochemistry studies by Montana Tech in the WSPOU. Field work focused on Pond 3, the largest and first in the series of treatment ponds. Shallow groundwater was sampled from 8 PVC piezometers located near the south end of Pond 3. Three sediment pore-water diffusion samplers (“peepers”) were also deployed at the south end of Pond 3 to examine vertical gradients in chemistry in the top 25 cm of the pond sediment. In general, the pH and Eh values of the shallow groundwater and sediment pore-water were less than in the pond water. Concentrations of arsenic were generally higher in subsurface water, and tended to pass through a maximum (up to 530 g/L) about 10 cm below the sediment-water interface. In the peeper cells, there was a strong positive correlation between dissolved As and dissolved Fe, and an inverse correlation with sulfate. Therefore, the zone of arsenic release corresponds to a zone of bacterial Fe and sulfate reduction in the shallow, organic-rich sediment. Redox speciation of arsenic shows that arsenate (As(V)) is dominant in the pond, and arsenite (As(III)) is dominant in the subsurface water. A series of laboratory experiments with pH adjustment were completed using SBC water collected near the inlet to the WSPOU as well as water and shallow sediment collected from Pond 3. Water ± sediment mesocosms were set up in 1-L Nalgene bottles (closed system) or a 20-L aquarium (open system), both with continuous stirring. The pH of the mesocosm was adjusted by addition of NaOH or HNO3 acid. The closed system provided better pH control since the water was not in contact with the atmosphere, which prevented exchange of carbon dioxide. In both the closed and open systems, dissolved arsenic concentrations either decreased or stayed roughly the same with increase in pH to values > 11. Therefore, the release of dissolved As into the treatment ponds in low-flow periods is not due to changes in pH alone. All of these results support the hypothesis that the arsenic release in WSPOU is linked to microbial reduction of ferric oxide minerals in the organic-rich sediment. Upwards diffusion of dissolved As from the sediment pore-water into the pond water is the most likely explanation for the increase in As concentration of the WSPOU in low-flow periods.

Lacunae Infills for in Situ Treatment of Historic Glazed Tiles

Knowledge of current conservation materials and methods together with those adopted in the past is essential to aid research and improve or develop better conservation options. The infill and painting of tile lacunae are subjected to special requirements mainly when used in outdoor settings. A selection of the most commonly used materials was undertaken and performed based on inquiries to practitioners working in the field. The infill pastes comprised organic (epoxy, polyester), inorganic (slaked lime,hydraulic lime and zinc hydroxychloride) and mixed organic–inorganic (slaked lime mixed with a vinylic resin)binders. The selected aggregates were those most commonly used or those already present in the commercially formulated products. The infill pastes were characterised by SEM, MIP, open porosity, water absorption by capillarity, water vapour permeability, thermal and hydric expansibilities and adhesion to the ceramic body. Their performance was assessed after curing, artificial ageing (salt ageing and UV–Temp–RH cycles) and natural ageing. The results were interpreted in terms of their significance as indicators of effectiveness, compatibility and durability

Effect of edible coatings with essential oils on the quality of red raspberries over shelf-life

The objective of the present work was to develop stategies for raising the shelf-life of red raspberries (Rubus idaeus L.). The quality of red raspberries over shelf-life after coated with alginate plus Brazilian Citrus essential oils was evaluated. Edible coatings did not significantly influence the firmness loss, soluble solids content (SCC), and brightness of fruits over time, when compared to control, nevertheless all edible coatings with essential oils induced higher weight loss than those samples in which the essential oils were not incorporated. Fruits coated with alginate plus lime essential oil (0.2%) or orange essential oil (0.1%) after 15 days of storage had less red skin, but were darker than the remaining samples. The less red colour verified in these samples was also coincident with the lower concentration of anthocyanins at the end of the experiment as well as the lower capacity for scavenging ABTS free radicals or quenching singlet oxygen. The edible coatings supplemented with the essential oil of orange either at 0.1 % or 0.2 % were very efficient to control the yeasts and moulds growth after 15 days of storage. To control the development of aerobic mesophilic bacteria the use of essential oil of lemon 0.2% and essential oil of orange 0.1% were the most efficient. The essential oils used in the edible coatings did not significantly change the sensorial properties of the fruit. Cyanidin-3-O-sophoroside, cyanidin-3-O-glucosylrutinoside, cyanidin-3-O-xylosylrutinoside, cyanidin-3-O-glucoside, cyanidin-3-O-rutinoside, pelargonidin-3-O-sophoroside, pelargonidin-3-O-glucosylrutinoside, pelargonidin 3-O-glucoside, pelargonidin 3-O-rutinoside were found in raspberries fruits. An unknown cyanidin derivative was also found in all samples, constituting 27.4% of total anthocyanin content.

Atrazine movement in a dark red latosol of the tropics.

Atrazine dissplacement was studied in a soll profile as function of water movement and time after herbicide application, taldng into account possible influences of preferential flow on keaching. The experiment consisted of two 7 x 7 m plots of a dark red latosol (Kanduidalfic Eutrudox), located at Pirecicaba, SP, Brazil (22o43'S and 47o25'W), 250 km inside continent, at an altitude of 580 m. One plot was previously treated with 1,000 kg/ha of lime, in order to increase saturation to 88%, and 500 kg/ha of gypsum. Each plot was instrumented with tensiometers, neutron probe acess tubes and soil solution extractors, in order to monitor water and atrazine flows. Atrazine was applied at the high rate of 6 kg/ha of active principllle. Results showed intensiive leaching of atrazine in the whole soil profile, up to the instrumented depth of 150 cm, alredy at the first sampling, seven days after herbicide application. The limed plot showed much higher atrazine leachinng losses than the other plot. The atrazine adsorption capacity of the soll is very low, its maximum value being of the order of 10%, for the 0-15 cm surface layer.

Ocorrência e controle de lesmas do gênero Omalonyx (Gastropoda, Succineidae), pragas de capim-elefante Pennisetum purpureum (Poaceae) em Rio Preto da Eva, Amazonas.

Lesmas do gênero Omalonyx d'Orbigny, 1837 são hermafroditas, herbívoras, de distribuição neotropical e vivem em plantas aquáticas, nas demais vegetações adjacentes e em solo úmido próximo a ambientes de água doce. No presente trabalho reporta-se a ocorrência atípica de O. pattersonae Tillier, 1981 e de Omalonyx sp. em área de terra firme, distante de ambiente aquático.