Oxidation of several p-phenylenediamines in room temperature ionic liquids: Estimation of transport and electrode kinetic parameters

The electrochemical oxidation of N,N,N',N'-tetramethyl-p-phenylenediamine (TMPD) has been studied by cyclic voltammetry and potential step chronoamperometry at 303 K in five ionic liquids, namely [C(2)mim] [NTf2], [C(4)mim] [NTf2] [C(4)mpyrr] [NTf2] [C(4)mim] [BF4], and [C(4)mim] [PF6] (where [C(n)mim](+) = 1-alkyl-3-methylimidazolium, [C(4)mpyrr](+) = N-butyl-N-methylpyrrolidinium, [NTf2](-) = bis(trifluoromethylsulfonyl)imide, [BF4](-) = tetrafluoroborate, and [PF6](-) = hexafluorophosphate). Diffusion coefficients, D, of 4.87, 3.32, 2.05, 1.74, and 1.34 x 10(-11) m(2) s(-1) and heterogeneous electron-transfer rate constants, k(0), of 0.0109, 0.0103, 0.0079, 0.0066, and 0.0059 cm s(-1) were calculated for TMPD in [C(2)mim] [NTf2], [C(4)mim] [NTf2], [C(4)mpyrr] [NTf2], [C(4)mim] [BF4], and [C(4)mim] [PF6], respectively, at 303 K. The oxidation of TMPD in [C4mim][PF6] was also carried out at increasing temperatures from 303 to 343 K, with an activation energy for diffusion of 32.3 kJ mol(-1). k(0) was found to increase systematically with increasing temperature, and an activation energy of 31.4 kJ mol(-1) was calculated. The study was extended to six other p-phenylenediamines with alkyl/phenyl group substitutions. D and k(0) values were calculated for these compounds in [C(2)mim] [NTf2], and it was found that k(0) showed no obvious relationship with the hydrodynamic radius, r.

Updated parameters for the transiting exoplanet WASP-3b using RISE, a new fast camera for the Liverpool Telescope

Some of the first results are reported from RISE - a new fast camera mounted on the Liverpool Telescope primarily designed to obtain high time-resolution light curves of transiting extrasolar planets for the purpose of transit timing. A full and partial transit of WASP-3 are presented, and a Markov-Chain Monte Carlo analysis is used to update the parameters from the discovery paper. This results in a planetary radius of 1.29(-0.12)(+0.05) R-J and therefore a density of 0.82(-0.09)(+0.14) rho(J), consistent with previous results. The inclination is 85.06(-0.15)(+0.16) deg, in agreement (but with a significant improvement in the precision) with the previously determined value. Central transit times are found to be consistent with the ephemeris given in the discovery paper; however, a new ephemeris calculated using the longer baseline results in T-c(0) = 2 454 605.55915 +/- 0.00023 HJD and P = 1.846835 +/- 0.000002 days.

The VLT-FLAMES survey of massive stars: atmospheric parameters and rotational velocity distributions for B-type stars in the Magellanic Clouds (vol 457, pg 265, 2006)

We correct the estimates of the dispersions in the rotational velocities for early-type stars in our Galaxy (Dufton et al. 2006, A&A, 457, 265) and the Magellanic Clouds (Hunter et al. 2008, A&A, 479, 541). The corrected values are pi(1/4) (i.e. approximately 33%) larger than those published in the original papers.

Factorial Design of Modelling Mix Proportion Parameters of Underwater Composite Cement Grouts

There is an increasing need to identify the rheological properties of cement grout using a simple test to determine the fluidity, and other properties of underwater applications such as washout resistance and compressive strength. This paper reviews statistical models developed using a factorial design that was carried out to model the influence of key parameters on properties affecting the performance of underwater cement grout. Such responses of fluidity included minislump and flow time measured by Marsh cone, washout resistance, unit weight, and compressive strength. The models are valid for mixes with 0.35–0.55 water-to-binder ratio (W/B), 0.053–0.141% of antiwashout admixture (AWA), by mass of water, and 0.4–1.8% (dry extract) of superplasticizer (SP), by mass of binder. Two types of underwater grout were tested: the first one made with cement and the second one made with 20% of pulverised fuel ash (PFA) replacement, by mass of binder. Also presented are the derived models that enable the identification of underlying primary factors and their interactions that influence the modelled responses of underwater cement grout. Such parameters can be useful to reduce the test protocol needed for proportioning of underwater cement grout. This paper attempts also to demonstrate the usefulness of the models to better understand trade-offs between parameters and compare the responses obtained from the various test methods that are highlighted.

The Role of Process Parameters in Determining Wall Thickness Distribution in Plug-Assisted Thermoforming

This article describes the results of a comprehensive investigation to determine the link between process parameters and observed wall thickness output for the plug-assisted thermoforming process. The overall objective of the work was to systematically investigate the process parameters that may be adjusted during production to control the wall thickness distribution of parts manufactured by plug-assisted thermoforming. The parameters investigated were the sheet temperature, plug temperature, plug speed, plug displacement, plug shape, and air pressure. As well as quantifying the effects of each parameter on the wall thickness distribution, a further aim of the work was to improve the understanding of the physical mechanisms of deformation of the sheet during the different stages of the process. The process parameters shown to have the greatest effect on experimentally determined wall thickness distribution were the plug displacement, sheet temperature, plug temperature, and plug shape. It is proposed that during the plug-assisted thermoforming of polystyrene the temperature dependent friction between the plug and sheet surface was the most important factor in determining product wall thickness distribution, whereas heat transfer was shown to play a less important role. POLYM. ENG. SCI., 2010. © 2010 Society of Plastics Engineers

Influence of post-calving regrouping strategy on welfare and performance parameters in dairy heifers

Thirty-six Holstein Friesian heifers (dairy herd replacements) were assigned to one of three regrouping treatments during the post-calving period. In Treatment 1, heifers were introduced individually to an established group of cows and heifers within 24 h of calving ('Single-day 1'). In Treatment 2, heifers were housed individually in a straw pen for I week after calving before being added individually to the group ('Single-day 7'). In Treatment 3, two heifers were housed together in a straw pen for 1 week after calving before being added as a pair to the group ('Pair-day T). The size of the resident group remained constant at 16 animals (10 mature cows and 6 first-lactation heifers). The behaviour of the heifers was assessed during their first 8 h and first month in the resident group, and milk yield parameters, body condition loss and live weight loss were assessed during the first month post-calving. Reproductive performance was assessed during the post-calving period, and hoof health parameters were measured I month prior to calving, and at I and 3 months post-calving. Heifers in the 'Pair-day 7' treatment appeared to associate closely during their first month in the group by spending more time than expected in the same pen area and in adjacent cubicles (P