System Integration of PV/T Collectors in Solar Cooling Systems

The demand for cooling and air-conditioning of building is increasingly ever growing. This increase is mostly due to population and economic growth in developing countries, and also desire for a higher quality of thermal comfort. Increase in the use of conventional cooling systems results in larger carbon footprint and more greenhouse gases considering their higher electricity consumption, and it occasionally creates peaks in electricity demand from power supply grid. Solar energy as a renewable energy source is an alternative to drive the cooling machines since the cooling load is generally high when solar radiation is high. This thesis examines the performance of PV/T solar collector manufactured by Solarus company in a solar cooling system for an office building in Dubai, New Delhi, Los Angeles and Cape Town. The study is carried out by analyzing climate data and the requirements for thermal comfort in office buildings. Cooling systems strongly depend on weather conditions and local climate. Cooling load of buildings depend on many parameters such as ambient temperature, indoor comfort temperature, solar gain to the building and internal gains including; number of occupant and electrical devices. The simulations were carried out by selecting a suitable thermally driven chiller and modeling it with PV/T solar collector in Polysun software. Fractional primary energy saving and solar fraction were introduced as key figures of the project to evaluate the performance of cooling system. Several parametric studies and simulations were determined according to PV/T aperture area and hot water storage tank volume. The fractional primary energy saving analysis revealed that thermally driven chillers, particularly adsorption chillers are not suitable to be utilizing in small size of solar cooling systems in hot and tropic climates such as Dubai and New Delhi. Adsorption chillers require more thermal energy to meet the cooling load in hot and dry climates. The adsorption chillers operate in their full capacity and in higher coefficient of performance when they run in a moderate climate since they can properly reject the exhaust heat. The simulation results also indicated that PV/T solar collector have higher efficiency in warmer climates, however it requires a larger size of PV/T collectors to supply the thermally driven chillers for providing cooling in hot climates. Therefore using an electrical chiller as backup gives much better results in terms of primary energy savings, since PV/T electrical production also can be used for backup electrical chiller in a net metering mechanism.

Demonstration of Solar Heating and Cooling System using Sorption Integrated Solar Thermal Collectors

Producing cost-competitive small and medium-sized solar cooling systems is currently a significant challenge. Due to system complexity, extensive engineering, design and equipment costs; the installation costs of solar thermal cooling systems are prohibitively high. In efforts to overcome these limitations, a novel sorption heat pump module has been developed and directly integrated into a solar thermal collector. The module comprises a fully encapsulated sorption tube containing hygroscopic salt sorbent and water as a refrigerant, sealed under vacuum with no moving parts. A 5.6m2 aperture area outdoor laboratory-scale system of sorption module integrated solar collectors was installed in Stockholm, Sweden and evaluated under constant re-cooling and chilled fluid return temperatures in order to assess collector performance. Measured average solar cooling COP was 0.19 with average cooling powers between 120 and 200 Wm-2 collector aperture area. It was observed that average collector cooling power is constant at daily insolation levels above 3.6 kWhm-2 with the cooling energy produced being proportional to solar insolation. For full evaluation of an integrated sorption collector solar heating and cooling system, under the umbrella of a European Union project for technological innovation, a 180 m2 large-scale demonstration system has been installed in Karlstad, Sweden. Results from the installation commissioned in summer 2014 with non-optimised control strategies showed average electrical COP of 10.6 and average cooling powers between 140 and 250 Wm-2 collector aperture area. Optimisation of control strategies, heat transfer fluid flows through the collectors and electrical COP will be carried out in autumn 2014.

Evaluation of a thermally driven heat pump for solar heating and cooling applications

Exploiting solar energy technology for both heating and cooling purposes has the potential of meeting an appreciable portion of the energy demand in buildings throughout the year. By developing an integrated, multi-purpose solar energy system, that can operate all twelve months of the year, a high utilisation factor can be achieved which translates to more economical systems. However, there are still some techno-economic barriers to the general commercialisation and market penetration of such technologies. These are associated with high system and installation costs, significant system complexity, and lack of knowledge of system implementation and expected performance. A sorption heat pump module that can be integrated directly into a solar thermal collector has thus been developed in order to tackle the aforementioned market barriers. This has been designed for the development of cost-effective pre-engineered solar energy system kits that can provide both heating and cooling. This thesis summarises the characterisation studies of the operation of individual sorption modules, sorption module integrated solar collectors and a full solar heating and cooling system employing sorption module integrated collectors. Key performance indicators for the individual sorption modules showed cooling delivery for 6 hours at an average power of 40 W and a temperature lift of 21°C. Upon integration of the sorption modules into a solar collector, measured solar radiation energy to cooling energy conversion efficiencies (solar cooling COP) were between 0.10 and 0.25 with average cooling powers between 90 and 200 W/m2 collector aperture area. Further investigations of the sorption module integrated collectors implementation in a full solar heating and cooling system yielded electrical cooling COP ranging from 1.7 to 12.6 with an average of 10.6 for the test period. Additionally, simulations were performed to determine system energy and cost saving potential for various system sizes over a full year of operation for a 140 m2 single-family dwelling located in Madrid, Spain. Simulations yielded an annual solar fraction of 42% and potential cost savings of €386 per annum for a solar heating and cooling installation employing 20m2 of sorption integrated collectors.

Effect of cooling rate on properties of plasma nitrided AISI 1010 steel

In this work, AISI 1010 steel samples were plasma nitrided into 20% N 2 100 Pa and 400 Pa for N 2 and H 2 , respectively), temperatures of 500 and 580 °C, during 2 h. Three different procedures for cooling were accomplished after nitriding. In the first procedure the cooling occurred naturally, that is, the sample was kept on substrate holder. In the second one the sample was pulled off and cooling in a cold surface. Finally, in the third cooling process the sample was pulled off the substrate holder down into special reservoir filled with oil held at ambient temperature. The properties of the AISI 1010 steel samples were characterized by optical and electron microscopy, X-ray diffraction, Mössbauer spectroscopy and microhardness tests. Thermal gradient inside the sample kept on substrate holder during cooling process was measured by three inserted thermocouples at different depths. When samples were cooled rapidly the transformation of ϵ-Fe 2 − 3 N to γ′-Fe 4 N was inhibited. Such effect is indicated by the high concentration of ϵ-Fe compound zone. To get solid state solution of nitrogen in the diffusion zone, instead of precipitates of nitride phases, the cooling rate should be higher than a critical value of about 0.95 °C/s. When this value is reached at any depth of the diffusion zone, two distinct diffusion zones will appear. Temperature gradients were measured inside the samples as a consequence of the plasma treatment. It's suggested the need for standardization of the term “treatment temperature” for plasma treatment because different nitrided layer properties could be reported for the same “treatment temperature”.

Performance and ruminal morphologic characteristics of Saanen kids fed ground, pelleted or extruded total ration

The aim of the present study was to determine feed intake and average weight gain and to evaluate the ruminal morphologic characteristics of Saanen kids slaughtered at 30, 45 and 60 days of age, according to a completely randomized design. Thirty-six non-castrated male Saanen kids were fed ground total ration, pelleted total ration, or extruded total ration. Feed intake and refusals were controlled daily and the animals were weighed at birth and then once a week. Newborn kids received a milk replacer and were weaned at 45 days. Immediately after slaughter, the animals were eviscerated, the entire digestive apparatus was removed from the carcass. The reticulo-rumen was separated, emptied, washed and weighed. Samples were collected from the dorsal sac, pillar area and ventral sac of the rumen, fixed for about 24h in Bouin's solution, dehydrated, embedded in Histosec and cut into 5 mu m sections. Results showed that dry matter intake (DMI) at weaning and post-weaning and weight gain were higher (P < 0.05) in animals that received the pelleted total ration. The weight of the reticulo-rumen accompanied body development and was heavier in these animals. Histologically, after weaning ruminal papillae were more developed in animals that received pelleted total ration. Length of papillae increased with increase of age. The ratio of papillary height to papillary width increased with age in the ventral sac and until weaning (P > 0.05). We conclude that the pelleting process of the total ration favored increased intake, with a 46.7% increase in weight gain and increase in rumen weight and papillae length, suggesting that best results are obtained with this processing. In general, no difference was observed between the results obtained with extruded and ground total ration, although animals fed extruded total ration showed an increase in rumen weight and papillae width. (c) 2004 Elsevier B.V All rights reserved.

Influence of the season of year, stage of lactation and milking time on the chloride content in bovine milk

From January to October 1995, chloride content determinations were accomplished in 2,218 samples of milk collected from 67 quarters of 17 lactating cows, in initial, middle and final stages of lactation, in the morning and afternoon milking. The highest means of chloride contents were observed among the milk samples collected in the final stage of lactation (0,203 gC1/100ml), in the summer (0,212 gC1/100ml) and in the morning milking (0,189 g C1/100ml). The differences observed between the chloride contents in the samples obtained in the different stages of lactation and the seasons of the year were statistically significant (P<0.0001). The gratest occornce of chloride at rates superior to 0.22 gC1100ml was observed in the final stge of lactation (31.4%), summer (44.2%) and after the morning milking (27.8%). These results evidentiate the influence of physiological and external factors (stage of lactation and season of the year) on the concentration of chloride of milk.

Molecular epidemiology of Staphylococcus aureus isolates at different sites in the milk producing dairy farms

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Shigatoxigenic Escherichia coli serogroups O157, O111 and O113 in feces, water and milk samples from dairy farms

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Free and total GMP (glycomacropeptide) contents of milk during bovine lactation

Amostras quinzenais, desde o parto até o final do período de lactação, obtidas de 34 vacas de três diferentes raças e propriedades, foram analisadas quanto à presença de GMP livre. Um pool das amostras quinzenais de cada rebanho foi analisada tanto para o conteúdo de GMP livre quanto para o GMP total (liberado da k-caseína pela ação da renina), correlacionando-os com as condições sanitárias do animal e do úbere, à fase da lactação e à produção de leite. A maioria dos problemas sanitários concentrou-se próximo ao parto, com poucas e espaçadas ocorrências de mastites clínicas. Os resultados do teste de CMT mostraram reações compatíveis às fases da lactação. Para o GMP livre as maiores variações ocorreram em função do período de lactação e em conseqüência de mastites clínicas e subclínicas. Valores elevados foram observados no início da lactação (5,87mg de ácido siálico/L de leite), normalizando para valores próximos de 3,30mg/L já ao final do segundo mês e voltando a elevar-se no terço final da lactação. em média, as mesmas tendências foram observadas para o teor de GMP total liberado pela ação de coalho comercial, iniciando com valores ligeiramente elevados (35,59mg/L), tornando-se normal e assim se mantendo até o sexto mês com valores próximos a 27,15mg/L, e novamente elevando-se gradualmente até o final da lactação, com 58,35mg de ácido siálico/L de leite. Esses resultados mostram-se úteis para a correta interpretação de métodos aplicados à seleção do leite, seja em relação ao status proteolítico da matéria-prima ou mesmo para coibição de fraudes por adição de soro ao leite.

Occurrence of Staphylococcus aureus in raw milk produced in dairy farms in São Paulo state, Brazil

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Virulence Genes in Isolates of Escherichia coli from Samples of Milk and Feces from Dairy Cattle

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Características físico-qímicas da carne de caprinos submetidos a diferentes níveis de substituição do leite por soro de queijo durante o aleitamento

Fifty six crossbred kids Parda Alpina x Gurgueia were separeted into four groups of 14 (seven male and seven female) and submited to four treatments with different levels of milk goat substitution by cheese serum. The treatments were : T1=milk goat (testify); T2=15% serum at 23 days and 33% at 55 days; T3=15% serum starting from 16 days, 33% on 23 days and 51% on 72 days of age; and T4=33% on 16 days and 69% of liquid diet in the final fase. At 92 days of age, all animals were slaughtered for carcass evaluation. Pallete were separeted from 20 male animals (five by treatment) and the physical and chemical analysis of the meat were realized using these materials. The studied characteristics were: total weight (TW), meat weight (MW), bone weigth (BW) of the pallete, and percentage of umidity (U), ashes (A), protein (P), fat (F) and pH of the pallete meat. There was significant effect of the treatment over F. Means of PW, A and BW were, respectively 491, 342 and 149.8 g. The meal represented 69,6% of total pallete weight. Means of U, A, P and F were 73, 1.0, 19 and 1.95%, respectively. The pH was 6.7. Results allow to conclude that only the fat percentage of the meat was modified, due to the administration of serun milk on the liquid diet of the kids, during the milking fase.

Relationship of black layer and milk line development on maize seed maturity

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Organic and inorganic sources of zinc, copper and selenium in diets for dairy cows: intake, blood metabolic profile, milk yield and composition

The present study was carried out with the objective of evaluating the effects of feeding dairy cows with organic or inorganic sources of zinc (Zn), copper (Cu) and selenium (Se) on blood concentrations of these minerals, blood metabolic profiles, nutrient intake and milk yield and composition. Nineteen Holstein cows were selected and randomly assigned to two groups for receiving organic (n = 9) or inorganic (n = 10) sources of Zn, Cu and Se from 60 days before the expected date of calving to 80 days of lactation. Samples of feed, orts and milk were collected for analysis. Body condition score (BCS) was determined and blood samples were collected for analysis of Zn, Cu and Se concentrations, as well as for metabolic profile. Supplying organic or inorganic sources of Zn, Cu, and Se did not affect dry matter and nutrient intake, blood metabolic profile, milk yield and composition, plasma concentration of these minerals, and BCS or change the BCS in cows from 60 days before the expected date of calving to 80 days of lactation. An effect of time was observed on all feed intake variables, plasma concentrations of Zn and Se, milk yield, milk protein content, BCS and change in BCS.

Random regressions models to describe the genetic variation of milk yield over multiple parities in Buffaloes

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)