First Measurement of the b-Jet Cross Section in Events with a W Boson in pp̅ Collisions at √s=1.96 TeV

The cross section for jets from b quarks produced with a W boson has been measured in ppbar collision data from 1.9/fb of integrated luminosity recorded by the CDF II detector at the Tevatron. The W+b-jets process poses a significant background in measurements of top quark production and prominent searches for the Higgs boson. We measure a b-jet cross section of 2.74 +- 0.27(stat.) +- 0.42(syst.) pb in association with a single flavor of leptonic W boson decay over a limited kinematic phase space. This measured result cannot be accommodated in several available theoretical predictions.

First measurement of the ratio of branching fractions B(Λb0→Λc+μ-ν̅ μ)/B(Λb0→Λc+π-)

This article presents the first measurement of the ratio of branching fractions B(Λb0→Λc+μ-ν̅ μ)/B(Λb0→Λc+π-). Measurements in two control samples using the same technique B(B̅ 0→D+μ-ν̅ μ)/B(B̅ 0→D+π-) and B(B̅ 0→D*(2010)+μ-ν̅ μ)/B(B̅ 0→D*(2010)+π-) are also reported. The analysis uses data from an integrated luminosity of approximately 172  pb-1 of pp̅ collisions at √s=1.96  TeV, collected with the CDF II detector at the Fermilab Tevatron. The relative branching fractions are measured to be B(Λb0→Λc+μ-ν̅ μ)/B(Λb0→Λc+π-)=16.6±3.0(stat)±1.0(syst)+2.6/-3.4(PDG)±0.3(EBR), B(B̅ 0→D+μ-ν̅ μ)/B(B̅ 0→D+π-)= 9.9±1.0(stat)±0.6(syst)±0.4(PDG)±0.5(EBR), and B(B̅ 0→D*(2010)+μ-ν̅ μ)/B(B̅ 0→D*(2010)+π-)=16.5±2.3(stat)± 0.6(syst)±0.5(PDG)±0.8(EBR). The uncertainties are from statistics (stat), internal systematics (syst), world averages of measurements published by the Particle Data Group or subsidiary measurements in this analysis (PDG), and unmeasured branching fractions estimated from theory (EBR), respectively. This article also presents measurements of the branching fractions of four new Λb0 semileptonic decays: Λb0→Λc(2595)+μ-ν̅ μ, Λb0→Λc(2625)+μ-ν̅ μ, Λb0→Σc(2455)0π+μ-ν̅ μ, and Λb0→Σc(2455)++π-μ-ν̅ μ, relative to the branching fraction of the Λb0→Λc+μ-ν̅ μ decay. Finally, the transverse-momentum distribution of Λb0 baryons produced in pp̅ collisions is measured and found to be significantly different from that of B̅ 0 mesons, which results in a modification in the production cross-section ratio σΛb0/σB̅ 0 with respect to the CDF I measurement.

First Observation of B̅ s0→Ds±K∓ and Measurement of the Ratio of Branching Fractions B(B̅ s0→Ds±K∓)/B(B̅ s0→Ds+π-)

A combined mass and particle identification fit is used to make the first observation of the decay B̅ s0→Ds±K∓ and measure the branching fraction of B̅ s0→Ds±K∓ relative to B̅ s0→Ds+π-. This analysis uses 1.2  fb-1 integrated luminosity of pp̅ collisions at √s=1.96  TeV collected with the CDF II detector at the Fermilab Tevatron collider. We observe a B̅ s0→Ds±K∓ signal with a statistical significance of 8.1σ and measure B(B̅ s0→Ds±K∓)/B(B̅ s0→Ds+π-)=0.097±0.018(stat)±0.009(syst).

First Measurement of the tt̅ Differential Cross Section dσ/dMtt̅ in pp̅ Collisions at √s=1.96 TeV

We present a measurement of the $\ttbar$ differential cross section with respect to the $\ttbar$ invariant mass, dSigma/dMttbar, in $\ppbar$ collisions at $\sqrt{s}=1.96$ TeV using an integrated luminosity of $2.7\invfb$ collected by the CDF II experiment. The $\ttbar$ invariant mass spectrum is sensitive to a variety of exotic particles decaying into $\ttbar$ pairs. The result is consistent with the standard model expectation, as modeled by \texttt{PYTHIA} with \texttt{CTEQ5L} parton distribution functions.

First simultaneous measurement of the top quark mass in the lepton+jets and dilepton channels at CDF

We present a measurement of the mass of the top quark using data corresponding to an integrated luminosity of 1.9fb^-1 of ppbar collisions collected at sqrt{s}=1.96 TeV with the CDF II detector at Fermilab's Tevatron. This is the first measurement of the top quark mass using top-antitop pair candidate events in the lepton + jets and dilepton decay channels simultaneously. We reconstruct two observables in each channel and use a non-parametric kernel density estimation technique to derive two-dimensional probability density functions from simulated signal and background samples. The observables are the top quark mass and the invariant mass of two jets from the W decay in the lepton + jets channel, and the top quark mass and the scalar sum of transverse energy of the event in the dilepton channel. We perform a simultaneous fit for the top quark mass and the jet energy scale, which is constrained in situ by the hadronic W boson mass. Using 332 lepton + jets candidate events and 144 dilepton candidate events, we measure the top quark mass to be mtop=171.9 +/- 1.7 (stat. + JES) +/- 1.1 (syst.) GeV/c^2 = 171.9 +/- 2.0 GeV/c^2.

First Observation of B̅ s0→Ds±K∓ and Measurement of the Ratio of Branching Fractions B(B̅ s0→Ds±K∓)/B(B̅ s0→Ds+π-)

A combined mass and particle identification fit is used to make the first observation of the decay Bs --> Ds K and measure the branching fraction of Bs --> Ds K relative to Bs --> Ds pi. This analysis uses 1.2 fb^-1 integrated luminosity of pbar-p collisions at sqrt(s) = 1.96 TeV collected with the CDF II detector at the Fermilab Tevatron collider. We observe a Bs --> Ds K signal with a statistical significance of 8.1 sigma and measure Br(Bs --> Ds K)/Br(Bs --> Ds pi) = 0.097 +- 0.018(stat) +- 0.009(sys).

First Observation of Vector Boson Pairs in a Hadronic Final State at the Tevatron Collider

We present the first observation in hadronic collisions of the electroweak production of vector boson pairs (VV, V=W, Z) where one boson decays to a dijet final state. The data correspond to 3.5  fb-1 of integrated luminosity of pp̅ collisions at √s=1.96  TeV collected by the CDF II detector at the Fermilab Tevatron. We observe 1516±239(stat)±144(syst) diboson candidate events and measure a cross section σ(pp̅ →VV+X) of 18.0±2.8(stat)±2.4(syst)±1.1(lumi)  pb, in agreement with the expectations of the standard model.

First Observation of Vector Boson Pairs in a Hadronic Final State at the Tevatron Collider

We present the first observation in hadronic collisions of the electroweak production of vector boson pairs (VV, V=W,Z) where one boson decays to a dijet final state . The data correspond to 3.5 inverse femtobarns of integrated luminosity of ppbar collisions at sqrt(s)=1.96 TeV collected by the CDFII detector at the Fermilab Tevatron. We observe 1516+/-239(stat)+/-144(syst) diboson candidate events and measure a cross section sigma(ppbar->VV+X) of 18.0+/-2.8(stat)+/-2.4(syst)+/-1.1(lumi) pb, in agreement with the expectations of the standard model.

Structure of Ce1-xSnxO2 and its relation to oxygen storage property from first-principles analysis

CeO2-SnO2 solid solution has been reported to possess high oxygen storage/release property which possibly originates from local structural distortion. We have performed first-principles based density functional calculations of Ce1-xSnxO2 structure (x=0, 0.25, 0.5, 1) to understand its structural stability in fluorite in comparison to rutile structure of the other end-member SnO2, and studied the local structural distortion induced by the dopant Sn ion. Analysis of relative energies of fluorite and rutile phases of CeO2, SnO2, and Ce1-xSnxO2 indicates that fluorite structure is the most stable for Ce1-xSnxO2 solid solution. An analysis of local structural distortions reflected in phonon dispersion show that SnO2 in fluorite structure is highly unstable while CeO2 in rutile structure is only weakly unstable. Thus, Sn in Ce1-xSnxO2-fluorite structure is associated with high local structural distortion whereas Ce in Ce1-xSnxO2-rutile structure, if formed, will show only marginal local distortion. Determination of M-O (M=Ce or Sn) bond lengths and analysis of Born effective charges for the optimized structure of Ce1-xSnxO2 show that local coordination of these cations changes from ideal eightfold coordination expected of fluorite lattice to 4+4 coordination, leading to generation of long and short Ce-O and Sn-O bonds in the doped structure. Bond valence analyses for all ions show the presence of oxygen with bond valence similar to 1.84. These weakly bonded oxygen ions are relevant for enhanced oxygen storage/release properties observed in Ce1-xSnxO2 solid solution. (C) 2010 American Institute of Physics.

First passage probability during random vibration

The probability that a random process crosses an arbitrary level for the first time is expressed as a Gram—Charlier series, the leading term of which is the Poisson approximation. The coefficients of this series are related to the moments of the number of level crossings. The results are applicable to both stationary and non-stationary processes. Some numerical results are presented for the response process of a linear single-degree-of-freedom oscillator under Gaussian white noise excitation.

Anisotropy of the Stone-Wales defect and warping of graphene nanoribbons: A first-principles analysis

Stone-Wales (SW) defects, analogous to dislocations in crystals, play an important role in mechanical behavior of sp(2)-bonded carbon based materials. Here, we show using first-principles calculations that a marked anisotropy in the interaction among the SW defects has interesting consequences when such defects are present near the edges of a graphene nanoribbon: depending on their orientation with respect to edge, they result in compressive or tensile stress, and the former is responsible to depression or warping of the graphene nanoribbon. Such warping results in delocalization of electrons in the defect states.

Design of first- and second-order sliding mode observers for induction motors using a stator-flux model

We extend current research in the area of 'sensorless' control of induction motors by presenting two observers based on first- and second-order sliding mode control theories for the simultaneous estimation of flux and speed. We base the observers on the stator-flux model of the motor instead of the usual rotor-flux model mainly because of the uncertain rotor resistance that plays a significant role in the latter. By designing the observers as if they are sliding mode controllers, we lend the properties of parameter insensitive closed-loop dynamics and finite time convergence to the stator flux and speed estimation schemes. We also present simulation and experimental results to validate the operation of the observers.

Relationship Drivers in Provider - Consumer Relationships. Empirical Studies of Customer Loyalty Programs (första upplagan slutsåld / first edition sold out, 'print on demand' 60 €)

The study addressed a phenomenon that has become common marketing practice, customer loyalty programs. Although a common type of consumer relationship, there is limited knowledge of its nature. The purpose of the study was to create structured understanding of the nature of customer relationships from both the provider’s and the consumer’s viewpoints by studying relationship drivers and proposing the concept of relational motivation as a provider of a common framework for the analysis of these views. The theoretical exploration focused on reasons for engaging in customer relationships for both the consumer and the provider. The themes of buying behaviour, industrial and network marketing and relationship marketing, as well as the concepts of a customer relationship, customer loyalty, relationship conditions, relational benefits, bonds and commitment were explored and combined in a new way. Concepts from the study of business-to-business relationships were brought over and their power in explaining the nature of consumer relationships examined. The study provided a comprehensive picture of loyalty programs, which is an important contribution to the academic as well as the managerial discussions. The consumer study provided deep insights into the nature of customer relationships. The study provides a new frame of reference to support the existing concepts of loyalty and commitment with the introduction of the relationship driver and relational motivation concepts. The result is a novel view of the nature of customer relationships that creates new understanding of the forces leading to loyal behaviour and commitment. The study concludes with managerial implications.

Understanding Customer Loyalty and Disloyalty The Effect of Loyalty-Supporting and -Repressing Factors (first edition sold out, 'print on demand' 60 €)

Customer loyalty has been a central topic of both marketing theory and practice for several decades. Customer disloyalty, or relationship ending, has received much less attention. Despite the close relation between customer loyalty and disloyalty, they have rarely been addressed in the same study. The thesis bridges this gap by focusing on both loyal and disloyal customers and the factors characterising them. Based on a qualitative study of loyal and disloyal bank customers in the Finnish retail banking market, both factors that are common to the groups and factors that differentiate between them are identified. A conceptual framework of factors that affect customer loyalty or disloyalty is developed and used to analyse the empirical data. According to the framework, customers’ loyalty status (behavioural and attitudinal loyalty) is influenced by positive, loyalty-supporting, and negative, loyalty-repressing factors. Loyalty-supporting factors either promote customer dedication, making the customer want to remain loyal, or act as constraints, hindering the customer from switching. Among the loyalty-repressing factors it is especially important to identify those that act as triggers of disloyal behaviour, making customers switch service providers. The framework further suggests that by identifying the sources of loyalty-supporting and -repressing factors (the environment, the provider, the customer, the provider-customer interaction, or the core service) one can determine which factors are within the control of the service provider. Attitudinal loyalty is approached through a customer’s “feeling of loyalty”, as described by customers both orally and graphically. By combining the graphs with behavioural loyalty, seven customer groups are identified: Stable Loyals, Rescued Loyals, Loyals at Risk, Positive Disloyals, Healing Disloyals, Fading Disloyals, and Abrupt Disloyals. The framework and models of the thesis can be used to analyse factors that affect customer loyalty and disloyalty in different service contexts. Since the empirical study was carried out in a retail bank setting, the thesis has managerial relevance especially for banks. Christina Nordman is associated with CERS, Center for Relationship Marketing and Service Management at the Swedish School of Economics and Business Administration. The doctoral thesis is part of the Göran Collert Research Project in Customer Relationships and Retail Banking and has been funded by The Göran Collert Foundation.

Tiering Effects in Third-party Logistics: A First-tier Buyer Perspective

This doctoral dissertation takes a buy side perspective to third-party logistics (3PL) providers’ service tiering by applying a linear serial dyadic view to transactions. It takes its point of departure not only from the unalterable focus on the dyad levels as units of analysis and how to manage them, but also the characteristics both creating and determining purposeful conditions for a longer duration. A conceptual framework is proposed and evaluated on its ability to capture logistics service buyers’ perceptions of service tiering. The problem discussed is in the theoretical context of logistics and reflects value appropriation, power dependencies, visibility in linear serial dyads, a movement towards the more market governed modes of transactions (i.e. service tiering) and buyers’ risk perception of broader utilisation of the logistics services market. Service tiering, in a supply chain setting, with the lack of multilateral agreements between supply chain members, is new. The deductive research approach applied, in which theoretically based propositions are empirically tested with quantitative and qualitative data, provides new insight into (contractual) transactions in 3PL. The study findings imply that the understanding of power dependencies and supply chain dynamics in a 3PL context is still in its infancy. The issues found include separation of service responsibilities, supply chain visibility, price-making behaviour and supply chain strategies under changing circumstances or influence of non-immediate supply chain actors. Understanding (or failing to understand) these issues may mean remarkable implications for the industry. Thus, the contingencies may trigger more open-book policies, larger liability scope of 3PL service providers or insourcing of critical logistics activities from the first-tier buyer core business and customer service perspectives. In addition, a sufficient understanding of the issues surrounding service tiering enables proactive responses to devise appropriate supply chain strategies. The author concludes that qualitative research designs, facilitating data collection on multiple supply chain actors, may capture and increase understanding of the impact of broader supply chain strategies. This would enable pattern-matching through an examination of two or more sides of exchange transactions to measure relational symmetries across linear serial dyads. Indeed, the performance of the firm depends not only on how efficiently it cooperates with its partners, but also on how well exchange partners cooperate with an organisation’s own business.