Learning sustainability by developing a solar dryer for microalgae retrieval

The development of nations depends on energy consumption, which is generally based on fossil fuels. This dependency produces irreversible and dramatic effects on the environment, e.g. large greenhouse gas emissions, which in turn cause global warming and climate changes, responsible for the rise of the sea level, floods, and other extreme weather events. Transportation is one of the main uses of energy, and its excessive fossil fuel dependency is driving the search for alternative and sustainable sources of energy such as microalgae, from which biodiesel, among other useful compounds, can be obtained. The process includes harvesting and drying, two energy consuming steps, which are, therefore, expensive and unsustainable. The goal of this EPS@ISEP Spring 2013 project was to develop a solar microalgae dryer for the microalgae laboratory of ISEP. A multinational team of five students from distinct fields of study was responsible for designing and building the solar microalgae dryer prototype. The prototype includes a control system to ensure that the microalgae are not destroyed during the drying process. The solar microalgae dryer works as a distiller, extracting the excess water from the microalgae suspension. This paper details the design steps, the building technologies, the ethical and sustainable concerns and compares the prototype with existing solutions. The proposed sustainable microalgae drying process is competitive as far as energy usage is concerned. Finally, the project contributed to increase the deontological ethics, social compromise skills and sustainable development awareness of the students.

Interpretative research in information systems: two qualitative research design projects

In a scientific research project is important to define the underlying philosophical orientation of the project, because this will influence the choices made in respect of scientific methods used, as well as the way they will be applied. It is crucial, therefore, that the philosophy and research design strategy are consistent with each other. These questions become even more relevant in qualitative research. Historically, the interpretive research philosophy is more associated to the scientific areas of social sciences and humanities where the subjectivity inherent to human intervention is more explicitly defined. Information systems field are, primarily, trapped in computer science field, though it also integrates issues related with management and organizations field. This shift from a purely technological guidance for the consideration of the problems of management and organizations has fostered the rise of research projects according to the interpretive philosophy and using qualitative methods. This paper explores the importance of alignment between the epistemological orientation and research design strategy, in qualitative research projects. As a result, it is presented two PhD projects, with different research design strategies, that are being developed in the technology and information systems field, in the light of the interpretive paradigm.

Sepsis Mortality Prediction Based on Predisposition, Infection and Response

OBJECTIVE: To empirically test, based on a large multicenter, multinational database, whether a modified PIRO (predisposition, insult, response, and organ dysfunction) concept could be applied to predict mortality in patients with infection and sepsis. DESIGN: Substudy of a multicenter multinational cohort study (SAPS 3). PATIENTS: A total of 2,628 patients with signs of infection or sepsis who stayed in the ICU for >48 h. Three boxes of variables were defined, according to the PIRO concept. Box 1 (Predisposition) contained information about the patient's condition before ICU admission. Box 2 (Injury) contained information about the infection at ICU admission. Box 3 (Response) was defined as the response to the infection, expressed as a Sequential Organ Failure Assessment score after 48 h. INTERVENTIONS: None. MAIN MEASUREMENTS AND RESULTS: Most of the infections were community acquired (59.6%); 32.5% were hospital acquired. The median age of the patients was 65 (50-75) years, and 41.1% were female. About 22% (n=576) of the patients presented with infection only, 36.3% (n=953) with signs of sepsis, 23.6% (n=619) with severe sepsis, and 18.3% (n=480) with septic shock. Hospital mortality was 40.6% overall, greater in those with septic shock (52.5%) than in those with infection (34.7%). Several factors related to predisposition, infection and response were associated with hospital mortality. CONCLUSION: The proposed three-level system, by using objectively defined criteria for risk of mortality in sepsis, could be used by physicians to stratify patients at ICU admission or shortly thereafter, contributing to a better selection of management according to the risk of death.

Emotion-oriented interventions for environment and the facilitation of pro-environmental behavior

Dissertação para obtenção do Grau de Doutor em Ambiente, pela Universidade Nova de Lisboa, Faculdade de Ciências e Tecnologia

THE EFFECT OF HOOKWORM INFECTION AND URINARY SCHISTOSOMIASIS ON BLOOD HEMOGLOBIN CONCENTRATION OF SCHOOLCHILDREN LIVING IN NORTHERN MOZAMBIQUE

This study aims to assess the association between schistosomiasis and hookworm infection with hemoglobin levels of schoolchildren in northern Mozambique. Through a cross-sectional survey, 1,015 children from five to 12 years old in the provinces of Nampula, Cabo Delgado and Niassa were studied. Hookworm infection and urinary schistosomiasis were diagnosed, through Ritchie and filtration methods, with a prevalence of 31.3% and 59.1%, respectively. Hemoglobin levels were obtained with a portable photometer (Hemocue®). The average hemoglobin concentration was 10.8 ± 1.42 g/dL, and 62.1% of the children presented levels below 11.5 g/dL, of which 11.8% of the total number of children had hemoglobin levels below 9 g/dL. A multiple linear regression analysis demonstrated negative interactions between hemoglobin levels and ancylostomiasis, this being restricted to the province of Cabo Delgado (β = -0.55; p < 0.001) where an independent interaction between hemoglobin levels and urinary schistosomiasis was also observed (β = -0.35; p = 0.016). The logistical regression model indicated that hookworm infection represents a predictor of mild (OR = 1.87; 95% CI = 1.17-3.00) and moderate/severe anemia (OR = 2.71; 95% CI = 1.50 - 4.89). We concluded that, in the province of Cabo Delgado, hookworm and Schistosoma haematobium infections negatively influence hemoglobin levels in schoolchildren. Periodical deworming should be considered in the region. Health education and improvements in sanitary infrastructure could achieve long-term and sustainable reductions in soil-transmitted helminthiases and schistosomiasis prevalence rates.

Conceção de um tutorial de Iniciação ao co-projeto de Hardware/software

A crescente evolução dos dispositivos contendo circuitos integrados, em especial os FPGAs (Field Programmable Logic Arrays) e atualmente os System on a chip (SoCs) baseados em FPGAs, juntamente com a evolução das ferramentas, tem deixado um espaço entre o lançamento e a produção de materiais didáticos que auxiliem os engenheiros no Co- Projecto de hardware/software a partir dessas tecnologias. Com o intuito de auxiliar na redução desse intervalo temporal, o presente trabalho apresenta o desenvolvimento de documentos (tutoriais) direcionados a duas tecnologias recentes: a ferramenta de desenvolvimento de hardware/software VIVADO; e o SoC Zynq-7000, Z-7010, ambos desenvolvidos pela Xilinx. Os documentos produzidos são baseados num projeto básico totalmente implementado em lógica programável e do mesmo projeto implementado através do processador programável embarcado, para que seja possível avaliar o fluxo de projeto da ferramenta para um projeto totalmente implementado em hardware e o fluxo de projeto para o mesmo projeto implementado numa estrutura de harware/software.

Strength and damage analysis of composite-aluminium adhesively-bonded single-lap joints

With the need to find an alternative way to mechanical and welding joints, and at the same time to overcome some limitations linked to these traditional techniques, adhesive bonds can be used. Adhesive bonding is a permanent joining process that uses an adhesive to bond the components of a structure. Composite materials reinforced with fibres are becoming increasingly popular in many applications as a result of a number of competitive advantages. In the manufacture of composite structures, although the fabrication techniques reduce to the minimum by means of advanced manufacturing techniques, the use of connections is still required due to the typical size limitations and design, technological and logistical aspects. Moreover, it is known that in many high performance structures, unions between composite materials with other light metals such as aluminium are required, for purposes of structural optimization. This work deals with the experimental and numerical study of single lap joints (SLJ), bonded with a brittle (Nagase Chemtex Denatite XNRH6823) and a ductile adhesive (Nagase Chemtex Denatite XNR6852). These are applied to hybrid joints between aluminium (AL6082-T651) and carbon fibre reinforced plastic (CFRP; Texipreg HS 160 RM) adherends in joints with different overlap lengths (LO) under a tensile loading. The Finite Element (FE) Method is used to perform detailed stress and damage analyses allowing to explain the joints’ behaviour and the use of cohesive zone models (CZM) enables predicting the joint strength and creating a simple and rapid design methodology. The use of numerical methods to simulate the behaviour of the joints can lead to savings of time and resources by optimizing the geometry and material parameters of the joints. The joints’ strength and failure modes were highly dependent on the adhesive, and this behaviour was successfully modelled numerically. Using a brittle adhesive resulted in a negligible maximum load (Pm) improvement with LO. The joints bonded with the ductile adhesive showed a nearly linear improvement of Pm with LO.

Atorvastatin versus Bezafibrate in Mixed Hyperlipidaemia : Randomised Clinical Trial of Efficacy and Safety (the ATOMIX Study)

OBJECTIVE: Combined hyperlipidaemia is a common and highly atherogenic lipid phenotype with multiple lipoprotein abnormalities that are difficult to normalise with single-drug therapy. The ATOMIX multicentre, controlled clinical trial compared the efficacy and safety of atorvastatin and bezafibrate in patients with diet-resistant combined hyperlipidaemia. PATIENTS AND STUDY DESIGN: Following a 6-week placebo run-in period, 138 patients received atorvastatin 10mg or bezafibrate 400mg once daily in a randomised, double-blind, placebo-controlled trial. To meet predefined low-density lipoprotein-cholesterol (LDL-C) target levels, atorvastatin dosages were increased to 20mg or 40mg once daily after 8 and 16 weeks, respectively. RESULTS: After 52 weeks, atorvastatin achieved greater reductions in LDL-C than bezafibrate (percentage decrease 35 vs 5; p < 0.0001), while bezafibrate achieved greater reductions in triglyceride than atorvastatin (percentage decrease 33 vs 21; p < 0.05) and greater increases in high-density lipoprotein-cholesterol (HDL-C) [percentage increase 28 vs 17; p < 0.01 ]. Target LDL-C levels (according to global risk) were attained in 62% of atorvastatin recipients and 6% of bezafibrate recipients, and triglyceride levels <200 mg/dL were achieved in 52% and 60% of patients, respectively. In patients with normal baseline HDL-C, bezafibrate was superior to atorvastatin for raising HDL-C, while in those with baseline HDL-C <35 mg/dL, the two drugs raised HDL-C to a similar extent after adjustment for baseline values. Both drugs were well tolerated. CONCLUSION: The results show that atorvastatin has an overall better efficacy than bezafibrate in concomitantly reaching LDL-C and triglyceride target levels in combined hyperlipidaemia, thus supporting its use as monotherapy in patients with this lipid phenotype.

An Exploratory Study Of Lean Construction in Portugal – Owners and Designers`Perspectives

21th Annual Conference of the International Group for Lean Construction (IGLC 21), July 2013, Fortaleza, Brazil

The relationship between the education level of successor's and the firm performance in German publicly listed family firms- an empirical analysis

The purpose of this thesis is to investigate how far the education level of the second or third generation of publicly traded German family firms affects the post-succession firm performance. By conducting a correlational and regression design, the aim is to examine how several variables influence the performance of family firms. Performance measures, for example ROA and Tobin’s q and variables, like Education level and succession periods, examine analytically that a positive succession trend will occur. However, with the used model, only a less rigid model shows empirical evidence.

Phenanthroimidazoles as fluorimetric and colourimetric chemosensors in aqueous solution

2,4,5-Triaryl-imidazoles are versatile compounds with application in medicine, due to their biological activity, and materials sciences, for their interesting optical properties. These properties can be tuned by careful selection of substituents at positions 2, 4 and 5: replacement of the aryl group by an heterocyclic group results in larger π-conjugated systems with improved optical properties for application in nonlinear optics, OLEDs, DNA intercalators, and chemosensors. Moreover, it is expected that introducing more conjugation and rigidity into the resulting system will further improve its properties. The development of chromo/fluorescent probes that are capable of detecting ions with high sensitivity and selectivity in aqueous media is currently a topic of strong interest and the design of heteroditopic receptors that contain two or more different binding sites for the simultaneous complexation of cationic and anionic guests is a emerging field of supramolecular chemistry. In this communication, we report the synthesis of new phenanthroimidazoles substituted at position 2 with arylthienyl or arylfuryl moieties possessing substituents of different electronic character, in order to tune the chromo/fluoro response in the presence of relevant anions and metal cations. Their photophysical properties and chemosensory ability were studied in acetonitrile and mixtures of acetonitrile and water, and selective detection of cyanide was achieved in aqueous mixtures for some of the derivatives.

A model to simulate the moment-rotation and crack width of FRC members reinforced with longitudinal bars

The present work describes a model for the determination of the moment–rotation relationship of a cross section of fiber reinforced concrete (FRC) elements that also include longitudinal bars for the flexural reinforcement (R/FRC). Since a stress–crack width relationship (σ–w)(σ–w) is used to model the post-cracking behavior of a FRC, the σ–w directly obtained from tensile tests, or derived from inverse analysis applied to the results obtained in three-point notched beam bending tests, can be adopted in this approach. For a more realistic assessment of the crack opening, a bond stress versus slip relationship is assumed to simulate the bond between longitudinal bars and surrounding FRC. To simulate the compression behavior of the FRC, a shear friction model is adopted based on the physical interpretation of the post-peak compression softening behavior registered in experimental tests. By allowing the formation of a compressive FRC wedge delimited by shear band zones, the concept of concrete crushing failure mode in beams failing in bending is reinterpreted. By using the moment–rotation relationship, an algorithm was developed to determine the force–deflection response of statically determinate R/FRC elements. The model is described in detail and its good predictive performance is demonstrated by using available experimental data. Parametric studies were executed to evidence the influence of relevant parameters of the model on the serviceability and ultimate design conditions of R/FRC elements failing in bending.

Effect of incorporating different waste materials in bitumen

The increasing environmental concern about waste materials and the necessity of improving the performance of asphalt mixtures prompted the study of incorporating different waste materials in conventional bitumen. The reuse of waste materials can present benefits at an environmental and economic level, and some wastes can be used to improve the pavement performance. Thus, the purpose of this study is to evaluate the incorporation of different waste materials in bitumen, namely waste motor oil and different polymers. In order to accomplish this goal, 10% of waste motor oil and 5% of polymers (high density polyethylene, crumb rubber and styrene-butadiene-styrene) were added to a conventional bitumen and the resulting modified bitumens were characterized through basic and rheological tests. From this work, it can be concluded that the incorporation of different waste materials improve some important properties of the conventional bitumen. Such improvements might indicate a good behaviour at medium/high temperatures and an increase of fatigue and rutting resistance. Therefore, these modified bitumens with waste materials can contribute to a sustainable development of road paving industry due to their performance and environmental advantages.

Foamed Bitumen: an alternative way of producing asphalt mixtures

With the constant need to improve and make the production of asphalt mixtures more sustainable, new production techniques have been developed, the implementation of which implies the correct knowledge of their performance. One of the most promising asphalt production techniques is the use of foamed bitumen. However, it is essential to understand how this binder will behave when subject to the expansion process. The loss of volume of the foamed bitumen could be translated by a decay curve, which allows to determine the ideal temperature and water content added to the bitumen in order to assure adequate conditions to the mix the bitumen with the aggregates. On the present study, a conventional 160/220 pen grade bitumen was tested by using different temperatures and water contents, and it was concluded that the optimum temperature for the production of foamed bitumen (with the studied bitumen) is 150 ºC, which corresponds to a viscosity of 0.1 Pa.s. The water content mostly influence the half-life of the bitumen foam, resulting in quicker volume reductions for higher water contents.

Study of the interaction between asphalt and plastic wastes in new polymer modified binders (PMB)

The aim of this study is evaluating the interaction between several base pen grade asphalt binders (35/50, 50/70, 70/100, 160/220) and two different plastic wastes (EVA and HDPE), for a set of new polymer modified binders produced with different amounts of both plastic wastes. After analysing the results obtained for the several polymer modified binders evaluated in this study, including a commercial modified binder, it can be concluded that the new PMBs produced with the base bitumen 70/100 and 5% of each plastic waste (HDPE or EVA) results in binders with very good performance, similar to that of the commercial modified binder.