Partikkelikokoanalyysimenetelmän kehittäminen

Päällystettyä paperia valmistettaessa syntyy päällystettyä hylkyä, joka kierrätetään takaisin prosessiin raaka-aineen tehokkaaksi hyödyntämiseksi. Hylyn mukana takaisin paperikoneen lyhyeen kiertoon päätyy myös pigmenttiaines levymäisinä partikkeleina. Nämä partikkelit rejektoituvat lyhyen kierron pyörrepuhdistimilla. Raaka-aineen hävikin pienentämiseksi käytetään lyhyessä kierrossa täyteaineen talteenottojärjestelmää, jonka tehtävänä on hienontaa päällystysainepartikkelit tasakokoisiksi, jotta ne voitaisiin palauttaa prosessiin. Talteenottolaitteistojen toiminnan tarkkailun kannalta on keskeistä tietää pyörrepuhdistuslaitoksen eri jakeiden partikkelikokojakaumat juuri pigmenttipartikkelien osalta. Tätä määritystä häiritsee näytteissä oleva kuitu. Tässä työssä pyrittiin löytämään partikkelikokoanalyysimenetelmä, jolla pigmenttien partikkelikokojakauma saataisiin selvitettyä kuidusta huolimatta. Aiemmin käytetty näytteen tuhkaus esikäsittelynä ennen partikkelikokoanalyysiä laserdiffraktiometrillä on osoittautunut toimimattomaksi. Kokeiden pääpaino keskittyi näytteen esikäsittelyyn fraktioinnilla ennen laserdiffraktioanalyysiä ja virtaussytometriamittauksiin. Fraktiointiin käytettiin DDJ-laitetta (dynamic drainage jar), joka oli varustettu metalliviiralla. Kumpikaan menetelmistä ei ollut täysin toimiva partikkelikokoanalyysiin, fraktioinnilla saadaan vähennettyä kuidun partikkelikokojakaumaan aiheuttamaa virhettä, mutta sen toimivuus riippuu paljolti näytteestä. Virtaussytometrialla väriainetta SYTO13 käyttämällä saadaan pigmenttipartikkelit tunnistettua ja näin rajattua kuidut pois mittauksista, mutta pigmenttiä ei saada erotettua puuperäisestä hienoaineesta, mikä vääristää mittaustulosta.

In vitro pollen germination and pollen viability in passion fruit (Passiflora spp.)

The use of Passiflora species for ornamental purposes has been recently developed, but little is known about pollen viability and the potential for crossing different species. The objective of this study was to evaluate the pollen viability of six Passiflora species collected from different physiological stages of development through in vitro germination and histochemical analysis using dyes. The pollen was collected in three stages (pre-anthesis, anthesis and post-anthesis). Three compositions of culture medium were used to evaluate the in vitro germination, and two dyes (2,3,5-triphenyltetrazolium chloride, or TTC, and Lugol's solution) were used for the histochemical analysis. The culture medium containing 0.03% Ca(NO3) 4H2O, 0.02% of Mg(SO4 ).7H2O, 0.01% of KNO3, 0,01% of H3BO3, 15% sucrose, and 0.8% agar, pH 7.0, showed a higher percentage of pollen grains germinated. Anthesis is the best time to collect pollen because it promotes high viability and germination. The Lugol's solution and TTC dye overestimated the viability of pollen, as all accessions showed high viability indices when compared with the results obtained in vitro.

Development of novel immunotherapies against bladder cancer

Le cancer de la vessie est le deuxième cancer urologique le plus fréquent dans le monde. La plupart des patients (75%) sont initialement diagnostiqués avec un cancer non musculo- invasif. Après résection trans-urétrale, ie traitement standard pour ce type de lésion chez les patients présentant un risque important de récidive/progression consiste en une série d'instillations intravésicales du Bacille de Calmette-Guerin (i.e. le vaccin BCG). Cependant cette "BCG thérapie" est associée à des effets secondaires non négligeables et s'avère inefficace dans 30% des cas, des limitations donc importantes qui soulignent la nécessité de développer des stratégies thérapeutiques alternatives. L'utilisation d'antigènes associés aux tumeurs (TAA) comme vaccin, combinée à une application locale d'immunostimulants sur le site tumoral, est une approche prometteuse en vue de maximiser les réponses immunitaires anti-tumorales localement. Nous montrons que la bactérie vivante atténuée Ty21a, issue du vaccin Vivotif® contre la fièvre typhoïde, peut être utilisée comme immunostimulant intravésical (IVES), mais ce uniquement dans le cas où la bactérie est en phase exponentielle de croissance (Vivotif exp). En effet, l'instillation IVES de Vivotif exp à la suite d'une vaccination par un TAA, un antigène mineur d'histocompatibilité mâle H-Y (Uty), permet d'augmenter de 15 fois le nombre de cellules T CD8 totales et spécifiques de l'antigène dans la vessie. Le recrutement des cellules T est TLR4-dépendent, ce qui suggère un rôle des lipopolysaccharides du Vivotif exp. Par ailleurs, en comparaison avec le contenu bactérien de la capsule de Vivotif, les bactéries en phase exponentielle de croissance permettent également une augmentation préférentielle des chemokines C5/C5a, CXCL1, CXCL2 et CXCL5 dans la vessie, mais pas du nombre de cellules T exprimant les récepteurs apparentés (C5aR et CXCR2). De plus, combiner la vaccination Uty avec le Vivotif exp en IVES permet d'améliorer la survie des souris présentant une tumeur orthotopique de la vessie exprimant l'antigène Uty (lignée tumorale murine MB49). Puisque pour certains cancers, aucun TAA - du moins exprimé à tous les stades tumoraux - n'est identifié, il est nécessaire de développer d'autres approches non vaccinales. Dans une deuxième partie de ce travail de thèse, nous avons donc investigué deux stratégies permettant d'induire une destruction des cellules tumorales, la thérapie génique par gène de suicide, d'une part, et la thérapie photodynamique dans le proche infrarouge (NIR-PDT), d'autre part. Pour appliquer ces thérapies, nous avons utilisé comme vecteur sûr et non toxique une forme non réplicative du virus du « Human Papillomavirus » (HPV) capable de "pseudo-infecter" préférentiellement les souris présentant des tumeurs vésicales (MB49). L'utilisation de pseudovirions (PsV) HPV portant comme gène suicide la thymidine kinase, une enzyme du virus de l'herpès simplex, suivi d'un traitement par la prodrogue Ganciclovir, permet de tuer 90% des cellules MB49 in-vitro ainsi que de ralentir significativement le développement des tumeurs vésicales in-vivo. Par ailleurs, l'emploi de particules pseudo- virales HPV couplées à la phtalocyanine IR700, un pigment photosensible présentant un pouvoir cytotoxique une fois activé, permet de tuer, après application d'une lumière dans le proche infrarouge, quasi 100% des cellules MB49 in-vitro et, plus important, de régresser des tumeurs in-vivo. De façon générale, ce travail de thèse présente des approches thérapeutiques innovantes et prometteuses pour le traitement des patients avec un cancer non musculo-invasif de la vessie. -- Bladder cancer is the second most common urological malignancy in the world. At initial diagnosis, non-muscle invasive bladder cancer (NMIBC) accounts for 75% of bladder cancer. The standard of care of NMIBC consists of intravesical (IVES) treatments with Bacillus- Calmette-Guerin (BCG) following transurethral resections of the lesions. However, repeated BCG treatments are associated with significant side effects and treatment failure may occur in 30% of the cases, underlying the necessity of alternative therapeutic strategies. The use of tumor-associated antigens (TAA) as vaccines followed by the local application of immunostimulants where the tumor resides is a promising approach to increase anti-tumor immune responses locally. We show that live attenuated Ty21a bacteria used from the vivotif® vaccine against typhoid fever can efficiently be used as IVES immunostimulant, only if bacteria are grown to exponential phase (Vivotif exp). In this condition, IVES immunostimulation after TAA vaccination with a minor histocompatibility male antigen HY (Uty) resulted in more than 15-fold increase of both vaccine-specific and total CD8-T cells in the bladder. T cell recruitment was mediated by TLR-4 suggesting that it was mainly mediated by lipopolysaccharides of Vivotif exp. In addition, these bacteria, as compared to the bacterial content of the vivotif capsule preferentially increased C5/C5a, CXCL1, CXCL2 and CXCL5 chemokines, but not the numbers of T cells expressing the cognate receptors (C5aR and CXCR2). Combination of IVES Vivotif exp with Uty vaccination improved survival of mice with pre-established orthotopic Uty-expressing MB49 murine bladder tumors, as compared to vaccination alone. As known TAA are not identified in all cancers, or not expressed in all stages of the tumor, we further investigated two potent approaches able of initiating tumor-cell destruction, suicide-gene therapy and near-infrared (NIR) photodynamic therapy (PDT). Towards a safe and non-toxic application of these therapies, we used Human Papillomavirus (HPV) replication-defective vectors that were able to preferentially pseudo-infect MB49-tumor bearing mice. HPV pseudovirions (PsV) carrying the Herpex-Simplex virus thymidine kinase suicide-gene followed by treatment with the prodrug Ganciclovir resulted in 90% of MB49 cell-death in-vitro and was able to significantly reduce bladder tumor growth in-vivo. Furthermore, HPV virus-like particles coupled to a NIR phtalocyanine dye, IR700 in combination with specific NIR light led to almost 100% of MB49 cell-death in-vitro and more interestingly, to bladder tumors shrinkage in-vivo. Overall, in this thesis, we offer promising therapeutic approaches for application in NMIBC patients.

Assessment of the role of LASER-Doppler in the treatment of port-wine stains in infants.

BACKGROUND: Port-wine stains (PWS) are malformations of capillaries in 0.3% of newborn children. The treatment of choice is by pulsed dye LASER (PDL), and requires several sessions. The efficacy of this treatment is at present evaluated on the basis of clinical inspection and of digital photographs taken throughout the treatment. LASER-Doppler imaging (LDI) is a noninvasive method of imaging the perfusion of the tissues by the microcirculatory system (capillaries). The aim of this paper is to demonstrate that LDI allows a quantitative, numerical evaluation of the efficacy of the PDL treatment of PWS. METHOD: The PDL sessions were organized according to the usual scheme, every other month, from September 1, 2012, to September 30, 2013. LDI imaging was performed at the start and at the conclusion of the PDL treatment, and simultaneously on healthy skin in order to obtain reference values. The results evidenced by LDI were analyzed according to the "Wilcoxon signed-rank" test before and after each session, and in the intervals between the three PDL treatment sessions. RESULTS: Our prospective study is based on 20 new children. On average, the vascularization of the PWS was reduced by 56% after three laser sessions. Compared with healthy skin, initial vascularization of PWS was 62% higher than that of healthy skin at the start of treatment, and 6% higher after three sessions. During the 2 months between two sessions, vascularization of the capillary network increased by 27%. CONCLUSION: This study shows that LDI can demonstrate and measure the efficacy of PDL treatment of PWS in children. The figures obtained when measuring the results by LDI corroborate the clinical assessments and may allow us to refine, and perhaps even modify, our present use of PDL and thus improve the efficacy of the treatment.

Brightness of multilayer boards

A good appearance of a package enhances the sale of the product. The packing gives information about the content and instructions for the usage. In this master’s thesis, the optical properties of multilayer packaging board is studied. Especially means of increasing brightness of the multilayer board are evaluated. In the literature part, the effect of different factors on optical properties of a multilayer board are evaluated with the help of light scattering and absorption coefficients. The Kubelka-Munk theory can be used also in modelling brightness of the multilayer board. A large variety of different process factors, chemical aids and machine variables affect optical properties of board. In the experimental part, different methods to increase brightness of a 3-layer board were evaluated. It was discovered that brightness variation of broke (30 % share of the center layer pulp) have only minor influence on brightness of the board. The brightness variation must be high, roughly 9 % in order to alter brightness of the board by 1 %. Higher brightness can be achieved by bleaching the pulp, which holds the largest share of the center layer pulp. Here, 2,6 % increase in brightness of the pulp (60 % share of the center layer pulp) increased brightness of the board by 1 %. In a trial run at a board machine, there was no indication of decreased bulk of the board due to extended bleaching of the pulp. With pulp dyeing appearance and optical properties of a multilayer board can be influenced. By using bluish dyes the natural yellowness of pulps can be decreased and impression of whiteness is then increased. Brightness may deteriorate though, because of increasing light absorption of the dyed pulps. When the yellowness comes from the center layer pulp, the dye should be introduced there. Then the brightness decreasing effect of the dye decreases brightness of the board less. It was noticed that it is more important to maintain brightness of the top layer than brightness of the center layer, because the top layer pulp affects on brightness of the board the most. By introducing fillers into the top layer of a multilayer board it is possible to increase brightness of the board. Fillers with the highest light scattering increased the brightness of the board the most. Increasing light scattering increases brightness and also opacity. Higher opacity in the top layer decreases also the darkening effect of the center layer. Calcinated kaolin and PCC was found to increase the light scattering of the top layer the most at the filler comparison. Introducing fillers into the top layer of multilayer board may decrease bulk and modulus of elasticity of the top layer. This could lead to deteriorated bending stiffness.

Fotoiniciação de polimerização vinílica

The initiation step of the light-induced polymerization kinetics of vinyl monomers using dye-sensitized photoinitiators to generate active radicals is discussed. The photoredox processes of basic dyes with amines and sulfinates are described as photochemical systems capable of starting free-radical polymerization of vinyl monomers in homogeneous and microheterogeneous media. Photophysical techniques like laser flash photolysis and time-correlated single photon counting are used to investigate the excited-state kinetics of the dyes.

Reduction and Analysis Methods of Indigo

Throughout history indigo was derived from various plants for example Dyer’s Woad (Isatis tinctoria L.) in Europe. In the 19th century were the synthetic dyes developed and nowadays indigo is mainly synthesized from by-products of fossil fuels. Indigo is a so-called vat dye, which means that it needs to be reduced to its water soluble leucoform before dyeing. Nowadays, most of the industrial reduction is performed chemically by sodium dithionite. However, this is considered environmentally unfavourable because of waste waters contaminating degradation products. Therefore there has been interest to find new possibilities to reduce indigo. Possible alternatives for the application of dithionite as the reducing agent are biologically induced reduction and electrochemical reduction. Glucose and other reducing sugars have recently been suggested as possible environmentally friendly alternatives as reducing agents for sulphur dyes and there have also been interest in using glucose to reduce indigo. In spite of the development of several types of processes, very little is known about the mechanism and kinetics associated with the reduction of indigo. This study aims at investigating the reduction and electrochemical analysis methods of indigo and give insight on the reduction mechanism of indigo. Anthraquinone as well as it’s derivative 1,8-dihydroxyanthraquinone were discovered to act as catalysts for the glucose induced reduction of indigo. Anthraquinone introduces a strong catalytic effect which is explained by invoking a molecular “wedge effect” during co-intercalation of Na+ and anthraquinone into the layered indigo crystal. The study includes also research on the extraction of plant-derived indigo from woad and the examination of the effect of this method to the yield and purity of indigo. The purity has been conventionally studied spectrophotometrically and a new hydrodynamic electrode system is introduced in this study. A vibrating probe is used in following electrochemically the leuco-indigo formation with glucose as a reducing agent.

Determinação espectrofotométrica por injeção em fluxo de vitamina B6 (piridoxina) em formulações farmacêuticas

A flow injection (FI) spectrophotometric procedure is proposed for the determination of vitamin B6 (pyridoxine hydrochloride) in pharmaceutical preparations. Powdered samples containing from 2.5 to 4.5 mg, were previously dissolved in 0.1 mol L-1 phosphate buffer solution (pH 7.0) and a volume of 500 muL was injected directly into a carrier stream consisting of this same phosphate buffer solution, flowing at 4.4 mL min-1. The stable blue indophenol dye produced in the oxidation of pyridoxine hydrochloride by potassium hexacyanoferrate(III) and N,N-diethyl-p-phenylenediamine solution was directly measured at 684 nm. Vitamin B6 was determined in five pharmaceutical preparations in the 0.5 to 6.0 mg L-1 concentration range (calibration graph: A= -0.00499 + 0.11963 C; r= 0.9991, where A is the absorbance and C is the vitamin B6 concentration in mg L-1), with a detection limit of 0.02 mg L-1 (3 Sblank/slope). The recovery of this vitamin from three samples ranged from 97.5 to 103.3 %. The analytical frequency was 62 h-1 and r.s.d. were less than 2% for solutions containing 1.0 and 3.0 mg L-1 vitamin B6 (n= 10). The results obtained for the determination of vitamin B6 in commercial formulations were in good agreement with those obtained by a spectrophotometric procedure (r=0.9997) and also with the label values (r= 0.9998).

Corantes têxteis

A dye is a colored substance used to impart permanent color to other substances. Its most important use is in coloring textile fibers and fabrics. The removal of colour from dyehouse waste waters is currently a major problem in the textile sector. This paper provides an overview of the treatment technologies that can currently be used by the textile processor and the developments over the past decade with respect to the toxicological and ecotoxicological properties of synthetic organic dyes.

Interações entre corantes e argilas em suspensão aquosa

Adsorption of cationic dyes on clays can be used as a model for the interactions between organic compounds and these minerals. Cationic dyes like methylene blue are used to study these interactions because of the spectroscopic changes observed when their molecules are adsorbed on clay surfaces. Depending on the structure and layer charge of the clay particles several processes may occur, like adsorption of dye monomers and aggregates on the external and internal surfaces of the clay tactoids, migration towards internal surfaces, protonation, etc. Under certain conditions the deaggregation-aggregation of the clay particles are accelerated trapping dye species during these processes. A general scheme is proposed for the processes occurring between clays and dyes in aqueous suspensions, which can be used to explain the behaviour of specific systems.

Gota suspensa para avaliação de aldeído total no ar interno e externo do ambiente

A sensitive and simple system was proposed for the in situ measurement of total aldehyde in outdoor or indoor ambient. The method is based on the use of a reagent drop as an useful interface to preconcentrate the sample prior to determination of total aldehyde as formaldehyde. The drop is formed at the tip of a cylindrical tube that contains two optical fibers placed on opposite sides and in contact with the reagent solution. One optical fiber carries the red light to the drop form a light emitting diode (LED). The transmitted light is measured by a second optical fiber/photodiode system. The analytical signal is read and converted into absorbance. The reagent solution of 3-methyl-2-benzothiazoline hydrazone (MBTH) forms a blue cation during reaction with formaldehyde that can be measured at 660 nm. Some aspects of kinetics reaction formation of dye were reevaluated. The formaldehyde reacts with MBTH and forms the azine in about 12 min. The oxidation of MBTH by Fe (III) and the formation of dye requires 3 min. The absorbance of the reagent drop is proportional to the sampling time and to the analyte concentration. The absorbance signal increases with increased sample gas flow until a maximum is reached then decreases until it forms a plateau. The proposed method was evaluated using both outdoor and indoor samples, and it was shown to viable provide an accurate measure of total aldehyde.

Novas tendências no tratamento de efluentes têxteis

Textile effluents, when not correctly treated, cause a high impact to the environment. The main recalcitrant compounds present in textile effluent are represented by the synthetic dyes, used during the fibber dying process. Among others, the azo dyes are considered the most harmful due to its mutagenic and carcinogenic character. In the present work we reported a revision study on the new tendencies for remediation of textile effluents, mainly to degrade the recalcitrant compounds. For this purpose, chemical, physical, photochemical, biological and combined processes were investigated.

Determinação espectrofotométrica por injeção em fluxo de paracetamol (acetaminofeno) em formulações farmacêuticas

A flow injection spectrophotometric procedure is proposed for the determination of paracetamol (acetaminophen) in pharmaceutical formulations. Powdered and liquid samples were previously dissolved/diluted in 0.05 mol L-1 hydrochloric acid solution and a volume of 250 µL was injected directly into a carrier stream of this same acid solution, flowing at 2.5 mL min-1. Paracetamol reacts with sodium hypochlorite forming N-acetyl-p-benzoquinoneimine which then reacts with sodium salicylate in sodium hydroxide solution yielding a blue indophenol dye which was measured at 640 nm in the pH range of 9.5-10.0. Paracetamol was determined in pharmaceutical products in the 1.0 to 100.0 mg L-1 (3.3x10-6 a 6.6x10-4 mol L-1) concentration range, with a detection limit of 0.5 mg L-1 (1.6x10-6 mol L-1). The recovery of this analyte in five samples ranged from 98.0 to 103.6 %. The analytical frequency was 80 determinations per hour and the RSDs were less than 1% for paracetamol concentrations of 25.0, 50.0 and 75.0 mg L-1 (n=10). A paired t-test showed that all results obtained for paracetamol in commercial formulations using the proposed flow injection procedure and a spectrophotometric batch procedure agree at the 95% confidence level.

Descoloração e degradação de poluentes orgânicos em soluções aquosas através do processo fotoeletroquímico

Organic compounds responsible for the color of wastewaters are usually refractory to biological digestion. In this paper the photo-assisted electrolysis process is used for color removal from three of the most colored wastewaters, which are daily generated in large amounts: the E1 bleach Kraft mill effluent, a textile reactive dye effluent and a landfill leachate. Electrolysis was carried out at 26,5 mA cm-2 in a flow reactor in which the anode surface was illuminated by a 400 W high pressure Hg bulb. In all experiments 70-75% of color reduction was observed which was also followed by a net organic load oxidation.

Transferência de energia entre corantes catiônicos em sistemas homogêneos

In this work, the energy transfer by dipole-dipole interaction between cationic dyes in n-alcohols (methanol, ethanol, 1-propanol and 1-butanol) is studied by time resolved and steady state fluorescence measurements. The critical radii of energy transfer were determined by three independent methods; the spectral overlap, fluorescence decay profiles, and relative intensity measurements. In all solvents, R0 values of the dye pairs obtained from spectral overlap were between 40 to 90 Å. Steady state and time resolved fluorescence measurements resulted in values of R0 in the range of 50 - 80 Å, with good correlation of values.