Improving the competitiveness of electrolytic Zinc process by chemical reaction engineering approach

This doctoral thesis describes the development work performed on the leachand purification sections in the electrolytic zinc plant in Kokkola to increase the efficiency in these two stages, and thus the competitiveness of the plant. Since metallic zinc is a typical bulk product, the improvement of the competitiveness of a plant was mostly an issue of decreasing unit costs. The problems in the leaching were low recovery of valuable metals from raw materials, and that the available technology offered complicated and expensive processes to overcome this problem. In the purification, the main problem was consumption of zinc powder - up to four to six times the stoichiometric demand. This reduced the capacity of the plant as this zinc is re-circulated through the electrolysis, which is the absolute bottleneck in a zinc plant. Low selectivity gave low-grade and low-value precipitates for further processing to metallic copper, cadmium, cobalt and nickel. Knowledge of the underlying chemistry was poor and process interruptions causing losses of zinc production were frequent. Studies on leaching comprised the kinetics of ferrite leaching and jarosite precipitation, as well as the stability of jarosite in acidic plant solutions. A breakthrough came with the finding that jarosite could precipitate under conditions where ferrite would leach satisfactorily. Based on this discovery, a one-step process for the treatment of ferrite was developed. In the plant, the new process almost doubled the recovery of zinc from ferrite in the same equipment as the two-step jarosite process was operated in at that time. In a later expansion of the plant, investment savings were substantial compared to other technologies available. In the solution purification, the key finding was that Co, Ni, and Cu formed specific arsenides in the “hot arsenic zinc dust” step. This was utilized for the development of a three-step purification stage based on fluidized bed technology in all three steps, i.e. removal of Cu, Co and Cd. Both precipitation rates and selectivity increased, which strongly decreased the zinc powder consumption through a substantially suppressed hydrogen gas evolution. Better selectivity improved the value of the precipitates: cadmium, which caused environmental problems in the copper smelter, was reduced from 1-3% reported normally down to 0.05 %, and a cobalt cake with 15 % Co was easily produced in laboratory experiments in the cobalt removal. The zinc powder consumption in the plant for a solution containing Cu, Co, Ni and Cd (1000, 25, 30 and 350 mg/l, respectively), was around 1.8 g/l; i.e. only 1.4 times the stoichiometric demand – or, about 60% saving in powder consumption. Two processes for direct leaching of the concentrate under atmospheric conditions were developed, one of which was implemented in the Kokkola zinc plant. Compared to the existing pressure leach technology, savings were obtained mostly in investment. The scientific basis for the most important processes and process improvements is given in the doctoral thesis. This includes mathematical modeling and thermodynamic evaluation of experimental results and hypotheses developed. Five of the processes developed in this research and development program were implemented in the plant and are still operated. Even though these processes were developed with the focus on the plant in Kokkola, they can also be implemented at low cost in most of the zinc plants globally, and have thus a great significance in the development of the electrolytic zinc process in general.

Sellutehtaan prosessien jätevesien puhdistaminen membraanitekniikalla

Tässä työssä tarkoituksena on tutkia mahdollisuuksia sellutehtaan eri jätevesien puhdistukseen uudelleenkäyttöä varten. Yleensä tutkimuksen kohteena ovat yleensä valkaisun alkalisen suodokset, koska niiden suodattaminen on ollut helppoa membraanitekniikalla. Tässä tutkimuksessa kuitenkin kiinnostuksen kohteena ovat valkaisun happamat suodokset ja kuorimon jätevedet. Tutkimuksessa käytettiin viittä membraania, joista kolme on ultrasuodatusmembraaneja ja kaksi nanosuodatusmembraaneja. Näiden katkaisukoot ovat väillä 30 000 -200 Da. Konsentraatiosuodatukset suoritettiin CR 250 -suodattimella. Syötöstä, konsentraatista ja permeaatista otettujen näytteiden analyysien pohjalta laskettujen retentioiden perusteella nanosuodatusmembraani NF270 antoi parhaan tuloksen. Tällä membraanilla kuorimon jätevesien suodatuksessa retentioksi saatiin kaikilla osa-alueilla vähintään 80 %, mutta valkaisun happamien suodosten tulokset olivat alhaisempia. Suodatusten perusteella voitiin laskea tarvittava kapasiteetti ja suodatuspinta-ala suodatus yksiköille. Kummassakin tapauksessa suodatuksen syöttömäärät määräytyivät erään suomalaisen sellutehtaan valkaisussa ja kuorimolla syntyvien jätevesimäärien mukaan. Suodatusyksiköiden kooksi saatiin valkaisun happamien suodosten suodattamiseen 54 CR 1010 -suodatinta ja kuorimon jätevesien suodattamiseen 4 CR 1010-suodatinta.

Influence of environmental factors on seed germination and seedling emergence of yellow sweet clover (Melilotus officinalis)

Laboratory and greenhouse experiments were conducted to determine the effects of drought and salinity stress, temperature, pH and planting depth on yellow sweet clover (Melilotus officinalis) germination and emergence. Base, optimum and ceiling germination temperatures were estimated as 0, 18.47 and 34.60 ºC, respectively. Seed germination was sensitive to drought stress and completely inhibited at a potential of -1 MPa, but it was tolerant to salinity. Salinity stress up to 90 mM had no effect over the M. officinalis seed germination, but the germination decreased by increasing the salt concentration. The drought and salinity required for 50% inhibition of maximum germination were 207 mM and -0.49 MPa, respectively. High percentage of seed germination (>92%) was observed at pH = 5-6 and decreased to 80% at acidic medium (pH 4) and to 42% at alkaline medium (pH 9) pH. Maximum seedling emergence occurred when the seeds were placed at 2 cm depth and decreased when increasing the depth of planting; no seed emerged from depths of 10 cm.

Characterization of Leaf-Type Ferredoxin-NADP+ Oxidoreductase (FNR) Isoforms in Arabidopsis thaliana

Life on earth is based on sunlight, which is captured in chemical form by photosynthetic reactions. In the chloroplasts of plants, light reactions of photosynthesis take place at thylakoid membranes, whereas carbon assimilation reactions occur in the soluble stroma. The products of linear electron transfer (LET), highly-energetic ATP molecules, and reducing power in the form of NADPH molecules, are further used in the fixation of inorganic CO2 molecules into organic sugars. Ferredoxin-NADP+ oxidoreductase (FNR) catalyzes the last of the light reactions by transferring electrons from ferredoxin (FD) to NADP+. In addition to LET, FNR has been suggested to play a role in cyclic electron transfer (CET), which produces ATP without the accumulation of reducing equivalents. CET is proposed to occur via two putative routes, the PGR5- route and the NDH-route. In this thesis, the leaf-type FNR (LFNR) isoforms LFNR1 and LFNR2 of a model organism, Arabidopsis thaliana, were characterized. The physiological roles of LFNRs were investigated using single and double mutant plants. The viability of the single mutants indicates functionality of both isoforms, with neither appearing to play a specific role in CET. The more severe phenotype of low-temperature adapted fnr2 plants compared to both wild-type (WT) and fnr1 plants suggests a specific role for LFNR2 under unfavorable growth conditions. The more severe phenotype of the fnr1 x fnr2 (F1 generation) plants compared to single mutants reflects down-regulated photosynthetic capacity, whereas slightly higher excitation pressure indicates mild over-excitation of electron transfer chain (ETC). However, induction of CET and various photoprotective mechanisms enable adaptation of fnr1 x fnr2 plants to scarcity of LFNR. The fnr1 fnr2 plants (F2 generation), without detectable levels of LFNR, were viable only under heterotrophic conditions. Moreover, drought stress induced acceleration of the rate of P700 + re-reduction in darkness was accompanied by a concomitant up-regulation of the PGR5-route specific components, PGR5 and PGRL1, demonstrating the induction of CET via the PGR5-route. The up-regulation of relative transcriptional expression of the FD1 gene indicates that the FD1 isoform may have a specific function in CET, while no such role could be defined for either of the LFNR isoforms. Both the membrane-bound and soluble LFNR1 and LFNR2 each appear as two distinct spots after 2D-PAGE with different isoelectric points (pIs), indicating the existence of post-translational modifications (PTMs) which do not determine the membrane attachment of LFNR. The possibility of phosphorylation and glycosylation PTMs were excluded, but all four LFNR forms were shown to contain acetylated lysine residues as well as alternative N-termini. N-terminal acetylation was shown to shift the pI of both LFNRs to be more acidic. In addition, all four LFNR forms were demonstrated to interact both with FD1 and FD2 in vitro

Influence of seed size and ecological factors on the germination and emergence of field bindweed (Convolvulus arvensis)

An understanding of seed germination ecology of weeds can assist in predicting their potential distribution and developing effective management strategies. Influence of environmental factors and seed size on germination and seedling emergence of Convolvulus arvensis (field bindweed) was studied in laboratory and greenhouse conditions. Germination occurred over a wide range of constant temperatures, between 15 and 40 ºC, with optimum germination between 20 and 25 ºC. Time to start germination, time to 50% germination and mean germination time increased while germination percentage and germination index decreased with an increase in temperature from 20 ºC, salinity and osmotic stress. However, germination was tolerant to low salt (25 mM) or osmotic stress (0.2 MPa), but as salinity and osmotic stress increased, germination percentage and germination index decreased. Seeds of C. arvensis placed at soil surface showed maximum emergence and decreased as seeding depth increased. Seeds of C. arvensis germinated over a wide range of pH (4 to 9) but optimum germination occurred at pH 6 to 8. Under highly alkaline and acidic pH, time to start germination, time to 50% germination and mean germination time increased while germination percentage and germination index decreased. Increase in field capacity caused decreased time to start germination, time to 50% germination and mean germination time but increased germination percentage and germination index. Bigger seeds had low time to start germination, time to 50% germination and mean germination time but high germination percentage and germination index. Smaller seeds were more sensitive to environmental factors as compared to larger or medium seeds. It can be concluded that except for pH, all environmental factors and seed sizes adversely affect C. arvensis as regards seed germination or emergence and germination or emergence traits, and larger seeds result in improved stand establishment and faster germination than small seeds, regardless of moisture stress or deeper seeding depth.

Seed germination and seedling emergence of velvetleaf (Abutilon theophrasti) and Barnyardgrass (Echinochloa crus-galli)

Abutilon theophrasti and Barnyardgrass (Echinochloa crus-galli) are major weeds that affect cropping systems worldwide. Laboratory and greenhouse studies were conducted to determine the effects of temperature, pH, water and salinity stress, and planting depth on seed germination and seedling emergence of Velvetleaf and Barnyardgrass. For Velvetleaf, the base, optimum and ceiling germination temperatures were estimated as 5, 35 and 48 ºC, respectively. Seed germination was sensitive to drought stress and completely inhibited by a potential of -0.6 MPa, but it was tolerant to salinity. Salinity stress up to 45 mM had no effect on the germination of Velvetleaf, but germination decreased with increasing salt concentration. Drought and salinity levels for 50% inhibition of maximum germination were -0.3 MPa and 110 mM, respectively. Seed germination of Velvetleaf was tolerant to a wide range of pH levels. For Barnyardgrass, the base, optimum and ceiling germination temperatures were estimated as 5, 38 and 45 ºC, respectively. Seed germination was tolerant to drought stress and completely inhibited by a potential of -1.0 MPa. Salinity stress up to 250 mM had no effect on seed germination. Drought and salinity levels for 50% inhibition of maximum germination were -0.5 MPa and 307 mM, respectively. A high percentage of seed germination was observed at pH=5 and decreased to 61.5% at acidic medium (pH 4) and to 11% at alkaline medium (pH 9). Maximum seedling emergence of Velvetleaf and Barnyardgrass occurred when the seeds were placed on the surface of the soil or at a depth of 1 cm.

Atlantic Forest succession over calcareous soil, Parque Estadual Turístico do Alto Ribeira - PETAR, SP

The forest succession after abandonment of slash-and-burn agriculture over calcareous soil in Brazilian Atlantic Forest was assessed. This is one of the world's most threatened Biome, with only 8% remaining. The study area is located over calcareous soil inside the Alto Ribeira Touristic State Park (PETAR), southeast Brazil. The phytossociological survey showed a successional pattern dominated by species of Leguminosae, especially Piptadenia gonoacantha (Mart.) J.F. Macbr. This species occurs in calcareous soils as a substitute of Tibouchina pulchra (Cham.) Cogn. (Melastomataceae) that is the most usual dominant tree species in early succession over acidic soil, which is the most common situation in this Biome. These results are important for a better understanding of Neotropical forest biodiversity and characterize a unique genetic bank in this highly endangered Biome. They are also decisive to support actions regarding rehabilitation of degraded lands and a potential tool for Neotropical forest sustainable management, both inside and around the conservation unit.

Treatment of Fe-containing Acid Mine Waters in Fixed Bed Adsorption Column with Calcite Side-Stone

The acid mining drainage is considered the most significant environmental pollution problem around the world for the extensive formation acidic leachates containing heavy metals. Adsorption is widely used methods in water treatment due to it easy operation and the availability of a wide variety of commercial adsorbent (low cost). The primary goal of this thesis was to investigate the efficiency of neutralizing agents, CaCO3 and CaSiO3, and metal adsorption materials with unmodified limestone from Company Nordkalk Oy. In addition to this, the side materials of limestone mining were tested for iron adsorption from acidic model solution. This study was executed at Lappeenranta University of Technology, Finland. The work utilised fixed-bed adsorption column as the main equipment and large fluidized column. Atomic absorption spectroscopy (AAS) and x-ray diffraction (XRD) was used to determine ferric removal and the composition of material respectively. The results suggest a high potential for the studied materials to be used a low cost adsorbents in acid mine drainage treatment. From the two studied adsorbents, the FS material was more suitable than the Gotland material. Based on the findings, it is recommended that further studies might include detailed analysis of Gotland materials.

Methyl and ethyl chloride synthesis in microreactors

Methyl chloride is an important chemical intermediate with a variety of applications. It is produced today in large units and shipped to the endusers. Most of the derived products are harmless, as silicones, butyl rubber and methyl cellulose. However, methyl chloride is highly toxic and flammable. On-site production in the required quantities is desirable to reduce the risks involved in transportation and storage. Ethyl chloride is a smaller-scale chemical intermediate that is mainly used in the production of cellulose derivatives. Thus, the combination of onsite production of methyl and ethyl chloride is attractive for the cellulose processing industry, e.g. current and future biorefineries. Both alkyl chlorides can be produced by hydrochlorination of the corresponding alcohol, ethanol or methanol. Microreactors are attractive for the on-site production as the reactions are very fast and involve toxic chemicals. In microreactors, the diffusion limitations can be suppressed and the process safety can be improved. The modular setup of microreactors is flexible to adjust the production capacity as needed. Although methyl and ethyl chloride are important chemical intermediates, the literature available on potential catalysts and reaction kinetics is limited. Thus the thesis includes an extensive catalyst screening and characterization, along with kinetic studies and engineering the hydrochlorination process in microreactors. A range of zeolite and alumina based catalysts, neat and impregnated with ZnCl2, were screened for the methanol hydrochlorination. The influence of zinc loading, support, zinc precursor and pH was investigated. The catalysts were characterized with FTIR, TEM, XPS, nitrogen physisorption, XRD and EDX to identify the relationship between the catalyst characteristics and the activity and selectivity in the methyl chloride synthesis. The acidic properties of the catalyst were strongly influenced upon the ZnCl2 modification. In both cases, alumina and zeolite supports, zinc reacted to a certain amount with specific surface sites, which resulted in a decrease of strong and medium Brønsted and Lewis acid sites and the formation of zinc-based weak Lewis acid sites. The latter are highly active and selective in methanol hydrochlorination. Along with the molecular zinc sites, bulk zinc species are present on the support material. Zinc modified zeolite catalysts exhibited the highest activity also at low temperatures (ca 200 °C), however, showing deactivation with time-onstream. Zn/H-ZSM-5 zeolite catalysts had a higher stability than ZnCl2 modified H-Beta and they could be regenerated by burning the coke in air at 400 °C. Neat alumina and zinc modified alumina catalysts were active and selective at 300 °C and higher temperatures. However, zeolite catalysts can be suitable for methyl chloride synthesis at lower temperatures, i.e. 200 °C. Neat γ-alumina was found to be the most stable catalyst when coated in a microreactor channel and it was thus used as the catalyst for systematic kinetic studies in the microreactor. A binder-free and reproducible catalyst coating technique was developed. The uniformity, thickness and stability of the coatings were extensively characterized by SEM, confocal microscopy and EDX analysis. A stable coating could be obtained by thermally pretreating the microreactor platelets and ball milling the alumina to obtain a small particle size. Slurry aging and slow drying improved the coating uniformity. Methyl chloride synthesis from methanol and hydrochloric acid was performed in an alumina-coated microreactor. Conversions from 4% to 83% were achieved in the investigated temperature range of 280-340 °C. This demonstrated that the reaction is fast enough to be successfully performed in a microreactor system. The performance of the microreactor was compared with a tubular fixed bed reactor. The results obtained with both reactors were comparable, but the microreactor allows a rapid catalytic screening with low consumption of chemicals. As a complete conversion of methanol could not be reached in a single microreactor, a second microreactor was coupled in series. A maximum conversion of 97.6 % and a selectivity of 98.8 % were reached at 340°C, which is close to the calculated values at a thermodynamic equilibrium. A kinetic model based on kinetic experiments and thermodynamic calculations was developed. The model was based on a Langmuir Hinshelwood-type mechanism and a plug flow model for the microreactor. The influence of the reactant adsorption on the catalyst surface was investigated by performing transient experiments and comparing different kinetic models. The obtained activation energy for methyl chloride was ca. two fold higher than the previously published, indicating diffusion limitations in the previous studies. A detailed modeling of the diffusion in the porous catalyst layer revealed that severe diffusion limitations occur starting from catalyst coating thicknesses of 50 μm. At a catalyst coating thickness of ca 15 μm as in the microreactor, the conditions of intrinsic kinetics prevail. Ethanol hydrochlorination was performed successfully in the microreactor system. The reaction temperature was 240-340°C. An almost complete conversion of ethanol was achieved at 340°C. The product distribution was broader than for methanol hydrochlorination. Ethylene, diethyl ether and acetaldehyde were detected as by-products, ethylene being the most dominant by-product. A kinetic model including a thorough thermodynamic analysis was developed and the influence of adsorbed HCl on the reaction rate of ethanol dehydration reactions was demonstrated. The separation of methyl chloride using condensers was investigated. The proposed microreactor-condenser concept enables the production of methyl chloride with a high purity of 99%.

Floristics, structure and soil of insular vegetation in four quartzite-sandstone outcrops of "Chapada Diamantina", Northeast Brazil

Soil islands on rocky surfaces often harbor aggregated vegetation that consists of insular plant communities. These islands are typical of the rocky outcrops and in various parts of Brazil form the so-called "campos rupestres" vegetation. Four of such sites have been selected in the state of Bahia, Northeast Brazil, for this comparative study on floristics and vegetation structure: three areas situated inside the "Parque Nacional da Chapada Diamantina" (Guiné, Fumaça and "Gerais da Fumaça") and one is at the border of the Environmental Protection Area of "Marimbus-Iraquara" ("Mãe Inácia"). All occurring vegetation islands were studied in four random plots of 10 × 10 m per site. Soil was often shallow, sandy and acidic. Vascular plant species were determined, with respective life forms and canopy coverage areas. The total number of species when all four sites were added was 135, and the number of species per island varied from 2 to 32. The areas of the 214 soil islands varied from 0.015 to 91.9 m², totaling 568 m² in the four sites. Monocotyledon families were dominant, essentially Velloziaceae, as well as Orchidaceae, Bromeliaceae, Amaryllidaceae and Cyperaceae. Among the eudicotyledons, dominant families were mainly Clusiaceae, Asteraceae and Melastomataceae. The biological spectra revealed that phanerophytes and hemicryptophytes predominated among the life forms, while chamaephytes had the largest coverage area. Epilithic and desiccant chamaephytes composed the most conspicuous interspecific associations, and were probably related to early successional processes. Sites closest to one another were not the most similar in structure, indicating that other factors more relevant than distance might be involved in the abundance of species in space.

Influence of soil properties on the abundance of plant species in ferruginous rocky soils vegetation, southeastern Brazil

Ferruginous "campos rupestres" are a particular type of vegetation growing on iron-rich primary soils. We investigated the influence of soil properties on plant species abundance at two sites of ferruginous "campos rupestres" and one site of quartzitic "campo rupestre", all of them in "Quadrilátero Ferrífero", in Minas Gerais State, southeastern Brazil. In each site, 30 quadrats were sampled to assess plant species composition and abundance, and soil samples were taken to perform chemical and physical analyses. The analyzed soils are strongly acidic and presented low fertility and high levels of metallic cations; a principal component analysis of soil data showed a clear segregation among sites due mainly to fertility and heavy metals content, especially Cu, Zn, and Pb. The canonical correspondence analysis indicated a strong correlation between plant species abundance and soil properties, also segregating the sites.

Milk protein polymorphisms in Brazilian Zebu cattle

Five bovine milk protein polymorphisms were studied in Zebuine cattle raised in Brazil, through horizontal electrophoresis on starch gel containing urea and 2-mercaptoethanol, using basic and acidic buffer systems. Allelic frequencies for a-La, b-Lg, aS1-Cn, b-Cn and k-Cn loci were estimated in six Gyr herds (N = 283), six Guzerat herds (N = 205), one Nelore herd (N = 17) and one Sindi herd (N = 22), all from São Paulo or Minas Gerais State, Brazil. Genotypic frequencies observed for each locus and breed studied are in accordance with the assumption of genetic equilibrium, demonstrating absence of high inbreeding levels for the breeds tested. The FST value found indicated significant genetic differentiation among breeds; however, the Gyr and Guzerat herds showed significantly different gene frequencies. Genetic distance estimates among zebuine breeds studied and the Holstein breed, taken as a reference for a taurine breed, showed strong differences between these two racial groups

Worker honeybee hemolymph lipid composition and synodic lunar cycle periodicities

The aim of the present investigation was to extend a previous study, showing a correlation of the variations of hemolymph carbohydrates with synodic lunar-like cycle and its circaseptan harmonics to worker honeybee hemolymph lipids. Hemolymph lipid concentrations of emerging worker imagos were analyzed in terms of one ideal synodic lunar cycle and processed by the cosinor method testing the null hypothesis versus the presence of 29.5-, 14.8- or 7.4-day periods in the data. A rhythmicity statistically compatible with a 29.5-day rhythm was observed for triacylglycerols and steroids as well as for body weight. A circadiseptan rhythm was determined for 1,3 diacylglycerols, while fatty acids and phospholipids exhibited a circaseptan rhythm. An agreement of peaks for triacylglycerols, steroids and body weight at the new moon, but not at the full moon, was noted with respect to trehalose and glucose circadiseptan rhythms. The latter moon-phase timing of peaks and nadirs, compared with that previously determined for trehalose and glucose, appeared to be identical to the circadiseptan rhythm and reciprocal for the circaseptan rhythms of 1,3 diacylglycerols. Reciprocal tendencies in circaseptans of trehalose and glucose on the one hand, and fatty acids and phospholipids on the other are indicated. The underlying causal nexus of these relationships is unknown

Thyroid hormone regulates protein expression in C6 glioma cells

Thyroid hormone (T3) is essential to normal brain development. Previously, we have shown that T3 induces cerebellar astrocyte proliferation. This effect is accompanied by alteration in glial fibrillary acidic protein (GFAP) and fibronectin organization. In the present study, we report that the C6 glioma cell line, which expresses GFAP and is classified as an undifferentiated astrocytic cell type, is a target for T3 action. The C6 monolayers were treated with 50 nM T3 for 3 days, after which the cells were maintained for 2 days without medium changes. In C6 cells, T3 induced the expression of proteins of 107, 73 and 62 kDa. The hormone also up-regulated protein bands of 100 (+50%), 37 (+50%) and 25.5 kDa (+50%) and down-regulated proteins of 94 (-100%), 86.5 (-100%), 68 (-100%), 60 (-100%), 54 (-33%), 51 (-33%) and 43.5 kDa (-33%). We suggest, on the basis of molecular mass, that the 54-, 51- and 43.5-kDa proteins could be the cytoskeletal proteins vimentin, GFAP and actin, respectively. The down-regulation of these proteins may be involved in the effects of thyroid hormone on C6 differentiation.

The calcium-modulated proteins, S100A1 and S100B, as potential regulators of the dynamics of type III intermediate filaments

The Ca2+-modulated, dimeric proteins of the EF-hand (helix-loop-helix) type, S100A1 and S100B, that have been shown to inhibit microtubule (MT) protein assembly and to promote MT disassembly, interact with the type III intermediate filament (IF) subunits, desmin and glial fibrillary acidic protein (GFAP), with a stoichiometry of 2 mol of IF subunit/mol of S100A1 or S100B dimer and an affinity of 0.5-1.0 µM in the presence of a few micromolar concentrations of Ca2+. Binding of S100A1 and S100B results in inhibition of desmin and GFAP assemblies into IFs and stimulation of the disassembly of preformed desmin and GFAP IFs. S100A1 and S100B interact with a stretch of residues in the N-terminal (head) domain of desmin and GFAP, thereby blocking the head-to-tail process of IF elongation. The C-terminal extension of S100A1 (and, likely, S100B) represents a critical part of the site that recognizes desmin and GFAP. S100B is localized to IFs within cells, suggesting that it might have a role in remodeling IFs upon elevation of cytosolic Ca2+ concentration by avoiding excess IF assembly and/or promoting IF disassembly in vivo. S100A1, that is not localized to IFs, might also play a role in the regulation of IF dynamics by binding to and sequestering unassembled IF subunits. Together, these observations suggest that S100A1 and S100B may be regarded as Ca2+-dependent regulators of the state of assembly of two important elements of the cytoskeleton, IFs and MTs, and, potentially, of MT- and IF-based activities.