Kuusiviilun esikuivaus puristamalla

Tutkimuksen lähtökohtana oli selvittää, voidaanko viilun valmistusprosessiin liittää uusi työvaihe, viilun esikuivaus. Esikuivauksen tarkoituksena on poistaa kosteutta viiluista ennen varsinaista kuivausta ja lisätä näin kuivauskapasiteettia. Tehdyissä tutkimuksissa viilut esikuivattiin nipuissa puristamalla. Muuttujina esikuivauksessa toimivat puristusaika ja -paine. Niiden määrittelyn lähtökohtana pidettiin sitä, etteivät viilun ominaisuudet saa merkittävästi heikentyä esikuivauksen aikana ja samalla viiluista on saatava mahdollisimman paljon kosteutta pois. Aikaisempien tutkimusten avulla selvitettiin vanerin valmistuksen, viilun kuivauksen sekä viilun esikuivauksen teoriaa. Lisäksi selvitettiin puun ominaisuuksien antamia mahdollisuuksia ja rajoitteita esikuivaukseen liittyen. Tutkimus koostui kahdesta osasta: laboratorio- ja tehdastutkimuksista. Laboratoriotutkimuksen tarkoituksena oli toimia tehdastutkimuksen esitutkimuksena. Laboratoriotutkimuksessa tutkittiin ainoastaan esikuivauksen vaikutusta märille viiluille. Tehdastutkimusosiossa esikuivatuista viiluista valmistettiin normaalin vanerinvalmistusprosessin kautta levyjä, joiden ominaisuuksia verrattiin normaaleista viiluista valmistettuihin vanereihin. Viilujen esikuivauksen todettiin pienentävän kuusiviilujen kosteuspitoisuutta. Tämän lisäksi kosteuspitoisuuden muutokset esikuivauksen aikana tapahtuivat tasaisesti niin yksittäisen viilun kuin viilunipunkin sisällä. Esikuivatuista viiluista valmistetut vanerilevyt täyttivät kaikki standardien sekä vanerin laadunvalvontasopimuksen asettamat vaatimukset. Esikuivauksen haitaksi tutkimuksissa todettiin viilun paksuuden pienentymä. Ennen esikuivauksen soveltamista teolliseen käyttöön nähtiin tarvetta lisätutkimukselle, jossa tulisi selvittää suurempien viilunippukokojen esikuivaamista sekä niiden varsinaista kuivaamista heti esikuivauksen jälkeen.

Avaliacão de programas de aquecimento para espectrometria de absorção atômica com atomizacão eletrotérmica em filamento de tungstênio

A tungsten coil atomizer was used to investigate the effect of heating programs with constant or variable drying temperatures on the atomization of Al, Cd, Cr and Pb. The variation of the surface temperature in the tungsten coil furnace can occur during each heating step due to the design of the power supply, that may apply constant voltages during a programmed time. For volatile elements (Cd), losses in sensitivity were observed when the program with a variable temperature was used. On the other hand, these effects are negligible for less volatile elements (Al and Cr) and any tested program, in different acidic media, could be used without appreciable changes in sensitivities. The results allow the establishment of proper heating programs for elements with different thermochemical behavior in the tungsten coil atomizer.

Dióxido de titânio sol-gel: propriedades e comportamento eletrocrômico

Titanium dioxide was prepared by hydrolysis and polycondensation of titanium tetraisopropoxide. TiO2 films were obtained by spin coating of the precursor solution on ITO substractes (glass covered with indium doped tin oxide). Films were prepared using different temperatures and hydrochloric acid contents. The effect of the drying temperature of the films (100 or 400ºC) was also investigated. TiO2 films were characterized by cyclic voltammetry, chronoamperometry, ultraviolete-visible spectroscopy, scanning electron microscopy and X-ray diffractrometry.

Esfoliação e hidratação da caulinita após intercalação com uréia

Well-ordered Georgia kaolinite (Kga-1b) obtained from the source Clay Repository of the Clay Minerals Society (USA) was intercalated with urea using grinding procedures. To achieve complete intercalation 20% of urea (in weight) was used, producing Al2Si2O5(OH)4 (N2H4CO)0,86 with an interplanar basal spacing of 1,08nm. After washing with water under ultrasound stirring at 363K, urea was completely removed and kaolinite was partially exfoliated. After drying under air, the material was converted to hydrated kaolinite with the composition Al2Si2O5(OH)4 (H2O)0,64 and an interplanar basal spacing of 0,84nm. In this compound, water molecules positioned between the layers of the silicate can be removed after calcination at 573K, regenerating structurally disordered kaolinite.

Síntese de membranas cerâmicas via método sol-gel utilizando TEOS e N,N-dimetilformamida

In this work we obtained microporous and mesoporous silica membranes by sol-gel processing. Tetraethylortosilicate (TEOS) was used as precursor. Nitric acid was used as catalyst. In order to study the affect of N,N-dimethylformamide (NDF) as drying additive, we used a molar ratio TEOS/NDF of 1/3. The performance of N,N-dimethylformamide was evaluated through monolithicity measurements. The structural evolutions occurring during the sol-gel transition and in the interconnected network of the membranes during thermal treatment were monitored by Fourier transform infrared spectroscopy (FTIR), thermogravimetric analyses and nitrogen sorption. We noted that in the presence of N,N-dimethylformamide, polymerization goes through a temporary stabilization of oligomers. The Si-O(H) bonds are stronger and belong to a more cross-linked structure for the N,N-dimethylformamide containing sol. The membranes obtained in the presence of N,N-dimethylformamide have larger surface area and its pore structure is in the range of mesoporous. The membranes obtained without additive have pore structure in the range of microporous.

Comportamento térmico da caulinita hidratada

Well-ordered kaolinite from the Brazilian Amazon Region (State of Pará) was initially reacted at 60 °C with a water dimethylsulfoxide mixture. After washing and characterisation, the resulting material was washed several times with methanol and in the final step with water. The water molecules displace the previously dimethylsulfoxide intercalated molecules and two different hydrated kaolinites were obtained. An unstable phase characterized by an interplanar basal distance of 0,996 nm that after drying collapse to the stable 0,844 nm hydrated kaolinite. The dehydration of the sample to disordered kaolinite was accompanied by Powder X-ray Diffractometry, thermal analysis (simultaneous TG and DSC) and FTIR spectroscopy.

Desenvolvimento de um sistema automatizado para a fabricação de filmes automontados

In this technical note, we describe the construction of a low-cost computer controlled device for layer-by-layer film fabrication. The software allows to control multiple material deposition, washing and drying steps and the time for each operation. To test the device, we produced and characterized self-assembled films of conductive polymers by alternating poly(o-methoxyaniline) (POMA) and poly(3-thiophene acetic acid) (PTAA) via the layer-by-layer technique.

Experimentos didáticos envolvendo radiação microondas

Theoretical and practical aspects of the use of microwave-assisted strategies in chemistry are introduced for students using simple and safe experiments employing a domestic oven. Three procedures are proposed for evaluating the distribution of microwave radiation inside the microwave oven cavity: (1) variation of the volume of marshmallows; (2) drying of filter paper wetted with Co(II) solution, and (3) variation of water temperature, after microwave-assisted heating. These experiments establish the position with the highest incidence of microwave radiation in the oven cavity, which was chosen for the synthesis of salicylic acid acetate. This synthesis was performed in 5 min of heating and the yield was around 85%. All experiments can be carried out in a 4 h lab-session using low-cost instrumentation.

Preparação de amostra de fígado bovino e estudo de micro homogeneidade para a determinação de Cd E Pb por espectrometria de absorção atômica com atomização eletrotérmica e amostragem direta de sólido

This work describes a systematic study for bovine liver sample preparation for Cd and Pb determination by solid sampling electrothermal atomic absorption spectrometry. Samples were prepared using different procedures: (1) drying in a household microwave oven followed by drying in a stove at 60 ºC until constant mass, and (2) freeze-drying. Ball and cryogenic mills were used for grinding. Particle size, sample size and micro sample homogeneity were investigated. All prepared samples showed good homogeneity (He < 10) even for low sample mass, but samples dried in a microwave oven/stove and ground in a ball mill presented the best homogeneity.

A convenient method for the determination of moisture in aromatic plants

A method is proposed for the determination of the moisture content of aromatic plants. This method is based on the co-distillation of the starting material in a modified Clevenger apparatus with four organic solvents (toluene, cyclohexane, dichloromethane and carbon tetrachloride). The results were compared with those obtained by oven drying at 105 ºC and steam distillation of the essential oil. The efficiencies of the methods were shown to be equivalent. The solvent distillation method was more practical, especially with respect to operating time (2 h).

Optimization of a heatset dryer

The objective of the thesis was to examine the possibilities in designing better performing nozzles for the heatset drying oven in Forest Pilot Center. To achieve the objective, two predesigned nozzle types along with the replicas of the current nozzles in the heatset drying oven were tested on a pilot-scale dryer. During the runnability trials, the pilot dryer was installed between the last printing unit and the drying oven. The two sets of predesigned nozzles were consecutively installed in the dryer. Four web tension values and four different impingement air velocities were used and the web behavior during the trial points was evaluated and recorded. The runnability in all trial conditions was adequate or even good. During the heat transfer trials, each nozzle type was tested on at least two different nozzle-to-surface distances and four different impingement air velocities. In a test situation, an aluminum plate fitted with thermocouples was set below a nozzle and the temperature measurement of each block was logged. From the measurements, a heat transfer coefficient profile for the nozzle was calculated. The performance of each nozzle type in tested conditions could now be rated and compared. The results verified that the predesigned simpler nozzles were better than the replicas. For runnability reasons, there were rows of inclined orifices on the leading and trailing edges of the current nozzles. They were believed to deteriorate the overall performance of the nozzle, and trials were conducted to test this hypothesis. The perpendicular orifices and inclined orifices of a replica nozzle were consecutively taped shut and the performance of the modified nozzles was measured as before, and then compared to the performance of the whole nozzle. It was found out, that after a certain nozzle-to-surface distance the jets from the two nozzles would collide, which deteriorates the heat transfer.

Korroosionesto polymeerin ekstruusiolinjalla

Tämä diplomityö tutkii korroosionestoa polymeerin ekstruusiolinjalla. Kirjallisuusosassa käsitellään ekstruusiolinjaa, linjalla valmistettavia tuotteita ja niiden jatkojalostusta. Lisäksi kirjallisuusosassa käydään läpi linjalla ilmeneviä korroosiotyyppejä, korroosiota eri prosessilaitteissa, korroosionestossa käytettäviä inhibiittoreita ja eri materiaalien korroosiokestävyyden kartoitusta. Kokeellisessa osassa tutkittiin perushartsin kuivauksen vaikutusta ekstruuderin kaasutilan metanoli-, happi- ja kosteuspitoisuuksiin. Kokeellisessa osassa tutkittiin myös korroosioinhibiittorien I1 ja I2 vaikutusta korroosionestoon, seuraamalla korrodoivalla alueella olleiden ruuvielementtien painohäviöitä. Kaapelitestauksessa selvitettiin inhibiittorien käytön vaikutukset matalajännitekaapelin laatuun. Kuivauksella ei todettu olevan vaikutusta korroosionestoon. Metanolipitoisuus pysyi korkeana ja happipitoisuuden aleneminen ei ollut merkittävää. Kosteuspitoisuuden suuruusluokka selvitettiin. Kuivauksesta huolimatta se pysyi korkeana. Inhibiittorien käytöstä huolimatta ruuvielementit korrodoituivat, mutta inhibiittoria I2 käytettäessä tutkittujen ruuvielementtien painohäviöt olivat pienempiä referenssiajoon verrattuna. Inhibiittori I2:lla ei todettu olevan negatiivisia vaikutuksia matalajännitekaapelin laatuun suoritetuissa ikääntymis- sähköominaisuus- ja ristisilloittumisnopeustesteissä.

Nanoparticle-coated organic-inorganic microparticles: experimental design and gastrointestinal tolerance evaluation

The influences of the spray-drying parameters and the type of nanoparticles (nanocapsules or nanospheres) on the characteristics of nanoparticle-coated diclofenac-loaded microparticles were investigated by using a factorial design 3². Gastrointestinal tolerance following oral administration in rats was evaluated. Formulations were selected considering the best yields, the best encapsulation efficiencies and the lowest water contents, presenting surfaces completely coated by nanostructures and a decrease in the surface areas in relation to the uncoated core. In vitro drug release demonstrated the influence of the nanoparticle-coating on the dissolution profiles of diclofenac. Nanocapsule-coated microparticles presented a protective effect on the gastrointestinal mucosa.

High pressure compression of filter cakes

The purpose of this thesis was to investigate the compression of filter cakes at high filtration pressures with five different test materials and to compare the energy consumption of high pressure compression with the energy consumption of thermal drying. The secondary target of this study was to investigate the particle deformation of test materials during filtration and compression. Literature part consists of basic theory of filtration and compression and of the basic parameters that influence the filtration process. There is also a brief description about all of the test materials including their properties and their industrial production and processing. Theoretical equations for calculating the energy consumptions of the filtrations at different conditions are also presented. At the beginning of the experiments at experimental part, the basic filtration tests were done with all the five test materials. Filtration tests were made at eight different pressures, from 6 bars up to 100 bars, by using piston press pressure filter. Filtration tests were then repeated by using a cylinder with smaller slurry volume than in the first series of filtration tests. Separate filtration tests were also done for investigating the deformation of solid particles during filtration and for finding the optimal curve for raising the filtration pressure. Energy consumption differences between high pressure filtration and ideal thermal drying process were done partly experimentally and partly by using theoretical calculation equations. By comparing these two water removal methods, the optimal ranges for their use were found considering their energy efficiency. The results of the measurements shows that the filtration rate increased and the moisture content of the filter cakes decreased as the filtration pressure was increased. Also the porosity of the filter cakes mainly decreased when the filtration pressure was increased. Particle deformation during the filtration was observed only with coal particles.

Influência da temperatura do ar de secagem sobre o teor e a composição química do óleo essencial de Lippia alba (Mill) N. E. Brown

Leaves of Lippia alba were submitted to six different drying treatments, using air at ambient temperature and heated up to 80 °C. The essential oil was extracted by steam distillation and analyzed by GC-MS. For the dried leaves, the oil content was reduced by 12 to 17% when compared with the fresh plant (0.66%). The major oil component was citral, representing 76% for the fresh plant, and varying from 82 to 84% for the dried material. These results showed that L. alba can be submitted to a drying process of up to 80 ºC without degradation and/or loss of the major, [LC1] active component.