A SCR Model based on Reactor and Engine Experimental Studies for a Cu-zeolite Catalyst

A NOx reduction efficiency higher than 95% with NH3 slip less than 30 ppm is desirable for heavy-duty diesel (HDD) engines using selective catalytic reduction (SCR) systems to meet the US EPA 2010 NOx standard and the 2014-2018 fuel consumption regulation. The SCR performance needs to be improved through experimental and modeling studies. In this research, a high fidelity global kinetic 1-dimensional 2-site SCR model with mass transfer, heat transfer and global reaction mechanisms was developed for a Cu-zeolite catalyst. The model simulates the SCR performance for the engine exhaust conditions with NH3 maldistribution and aging effects, and the details are presented. SCR experimental data were collected for the model development, calibration and validation from a reactor at Oak Ridge National Laboratory (ORNL) and an engine experimental setup at Michigan Technological University (MTU) with a Cummins 2010 ISB engine. The model was calibrated separately to the reactor and engine data. The experimental setup, test procedures including a surrogate HD-FTP cycle developed for transient studies and the model calibration process are described. Differences in the model parameters were determined between the calibrations developed from the reactor and the engine data. It was determined that the SCR inlet NH3 maldistribution is one of the reasons causing the differences. The model calibrated to the engine data served as a basis for developing a reduced order SCR estimator model. The effect of the SCR inlet NO2/NOx ratio on the SCR performance was studied through simulations using the surrogate HD-FTP cycle. The cumulative outlet NOx and the overall NOx conversion efficiency of the cycle are highest with a NO2/NOx ratio of 0.5. The outlet NH3 is lowest for the NO2/NOx ratio greater than 0.6. A combined engine experimental and simulation study was performed to quantify the NH3 maldistribution at the SCR inlet and its effects on the SCR performance and kinetics. The uniformity index (UI) of the SCR inlet NH3 and NH3/NOx ratio (ANR) was determined to be below 0.8 for the production system. The UI was improved to 0.9 after installation of a swirl mixer into the SCR inlet cone. A multi-channel model was developed to simulate the maldistribution effects. The results showed that reducing the UI of the inlet ANR from 1.0 to 0.7 caused a 5-10% decrease in NOx reduction efficiency and 10-20 ppm increase in the NH3 slip. The simulations of the steady-state engine data with the multi-channel model showed that the NH3 maldistribution is a factor causing the differences in the calibrations developed from the engine and the reactor data. The Reactor experiments were performed at ORNL using a Spaci-IR technique to study the thermal aging effects. The test results showed that the thermal aging (at 800°C for 16 hours) caused a 30% reduction in the NH3 stored on the catalyst under NH3 saturation conditions and different axial concentration profiles under SCR reaction conditions. The kinetics analysis showed that the thermal aging caused a reduction in total NH3 storage capacity (94.6 compared to 138 gmol/m3), different NH3 adsorption/desorption properties and a decrease in activation energy and the pre-exponential factor for NH3 oxidation, standard and fast SCR reactions. Both reduction in the storage capability and the change in kinetics of the major reactions contributed to the change in the axial storage and concentration profiles observed from the experiments.

Novel Automotive Waste Heat Recovery Techniques

The United States transportation industry is predicted to consume approximately 13 million barrels of liquid fuel per day by 2025. If one percent of the fuel energy were salvaged through waste heat recovery, there would be a reduction of 130 thousand barrels of liquid fuel per day. This dissertation focuses on automotive waste heat recovery techniques with an emphasis on two novel techniques. The first technique investigated was a combination coolant and exhaust-based Rankine cycle system, which utilized a patented piston-in-piston engine technology. The research scope included a simulation of the maximum mass flow rate of steam (700 K and 5.5 MPa) from two heat exchangers, the potential power generation from the secondary piston steam chambers, and the resulting steam quality within the steam chamber. The secondary piston chamber provided supplemental steam power strokes during the engine's compression and exhaust strokes to reduce the pumping work of the engine. A Class-8 diesel engine, operating at 1,500 RPM at full load, had a maximum increase in the brake fuel conversion efficiency of 3.1%. The second technique investigated the implementation of thermoelectric generators on the outer cylinder walls of a liquid-cooled internal combustion engine. The research scope focused on the energy generation, fuel energy distribution, and cylinder wall temperatures. The analysis was conducted over a range of engine speeds and loads in a two cylinder, 19.4 kW, liquid-cooled, spark-ignition engine. The cylinder wall temperatures increased by 17% to 44% which correlated well to the 4.3% to 9.5% decrease in coolant heat transfer. Only 23.3% to 28.2% of the heat transfer to the coolant was transferred through the TEG and TEG surrogate material. The gross indicated work decreased by 0.4% to 1.0%. The exhaust gas energy decreased by 0.8% to 5.9%. Due to coolant contamination, the TEG output was not able to be obtained. TEG output was predicted from cylinder wall temperatures and manufacturer documentation, which was less than 0.1% of the cumulative heat release. Higher TEG conversion efficiencies, combined with greater control of heat transfer paths, would be needed to improve energy output and make this a viable waste heat recovery technique.

DEVELOPMENT OF ION EXCHANGE MODELS FOR WATER TREATMENT AND APPLICATION TO THE INTERNATIONAL SPACE STATION WATER PROCESSOR

The International Space Station (ISS) requires a substantial amount of potable water for use by the crew. The economic and logistic limitations of transporting the vast amount of water required onboard the ISS necessitate onboard recovery and reuse of the aqueous waste streams. Various treatment technologies are employed within the ISS water processor to render the waste water potable, including filtration, ion exchange, adsorption, and catalytic wet oxidation. The ion exchange resins and adsorption media are combined in multifiltration beds for removal of ionic and organic compounds. A mathematical model (MFBMODEL™) designed to predict the performance of a multifiltration (MF) bed was developed. MFBMODEL consists of ion exchange models for describing the behavior of the different resin types in a MF bed (e.g., mixed bed, strong acid cation, strong base anion, and weak base anion exchange resins) and an adsorption model capable of predicting the performance of the adsorbents in a MF bed. Multicomponent ion exchange ii equilibrium models that incorporate the water formation reaction, electroneutrality condition, and degree of ionization of weak acids and bases for mixed bed, strong acid cation, strong base anion, and weak base anion exchange resins were developed and verified. The equilibrium models developed use a tanks-inseries approach that allows for consideration of variable influent concentrations. The adsorption modeling approach was developed in related studies and application within the MFBMODEL framework was demonstrated in the Appendix to this study. MFBMODEL consists of a graphical user interface programmed in Visual Basic and Fortran computational routines. This dissertation shows MF bed modeling results in which the model is verified for a surrogate of the ISS waste shower and handwash stream. In addition, a multicomponent ion exchange model that incorporates mass transfer effects was developed, which is capable of describing the performance of strong acid cation (SAC) and strong base anion (SBA) exchange resins, but not including reaction effects. This dissertation presents results showing the mass transfer model's capability to predict the performance of binary and multicomponent column data for SAC and SBA exchange resins. The ion exchange equilibrium and mass transfer models developed in this study are also applicable to terrestrial water treatment systems. They could be applied for removal of cations and anions from groundwater (e.g., hardness, nitrate, perchlorate) and from industrial process waters (e.g. boiler water, ultrapure water in the semiconductor industry).

The Development of Calibrants through Characterization of Volatile Organic Compounds from Peroxide Based Explosives and a Non-target Chemical Calibration Compound

Detection canines represent the fastest and most versatile means of illicit material detection. This research endeavor in its most simplistic form is the improvement of detection canines through training, training aids, and calibration. This study focuses on developing a universal calibration compound for which all detection canines, regardless of detection substance, can be tested daily to ensure that they are working with acceptable parameters. Surrogate continuation aids (SCAs) were developed for peroxide based explosives along with the validation of the SCAs already developed within the International Forensic Research Institute (IFRI) prototype surrogate explosives kit. Storage parameters of the SCAs were evaluated to give recommendations to the detection canine community on the best possible training aid storage solution that minimizes the likelihood of contamination. Two commonly used and accepted detection canine imprinting methods were also evaluated for the speed in which the canine is trained and their reliability. As a result of the completion of this study, SCAs have been developed for explosive detection canine use covering: peroxide based explosives, TNT based explosives, nitroglycerin based explosives, tagged explosives, plasticized explosives, and smokeless powders. Through the use of these surrogate continuation aids a more uniform and reliable system of training can be implemented in the field than is currently used today. By examining the storage parameters of the SCAs, an ideal storage system has been developed using three levels of containment for the reduction of possible contamination. The developed calibration compound will ease the growing concerns over the legality and reliability of detection canine use by detailing the daily working parameters of the canine, allowing for Daubert rules of evidence admissibility to be applied. Through canine field testing, it has been shown that the IFRI SCAs outperform other commercially available training aids on the market. Additionally, of the imprinting methods tested, no difference was found in the speed in which the canines are trained or their reliability to detect illicit materials. Therefore, if the recommendations discovered in this study are followed, the detection canine community will greatly benefit through the use of scientifically validated training techniques and training aids.

Investigation of Escape and Negative Student Behaviors Related to Florida State High Stakes Test Preparation in Miami-Dade County Public High Schools, having been approved in respect to style and intellectual content, is referred to you for judgment

The purpose of this study was to determine whether there was a relationship between pressure to perform on state mandated, high-stakes tests and the rate of student escape behavior defined as the number of school suspensions and absences. The state assigned grade of a school was used as a surrogate measure of pressure with the assumption that pressure increased as the school grade decreased. Student attendance and suspension data were gathered from all 33 of the regular public high schools in Miami-Dade County Public Schools. The research questions were: Is the number of suspensions highest in the third quarter, when most FCAT preparation takes place for each of the 3 school years 2007-08 through 2009-10? How accurately does the high school’s grade predict the number of suspensions and number of absences during each of the 4 school years 2005-06 through 2008-09? The research questions were answered using repeated measures analysis of variance for research question #1 and non-linear multiple regression for research question #2. No significant difference could be found between the numbers of suspensions in each of the grading periods nor was there a relationship between the number of suspensions and school grade. A statistically significant relationship was found between student attendance and school grade. When plotted, this relationship was found to be quadratic in nature and formed a loose inverted U for each of the four years during which data were collected. This indicated that students in very high and very low performing schools had low levels of absences while those in the midlevel of the distribution of school performance (C schools) had the greatest rates of absence. Identifying a relationship between the pressures associated with high stakes testing and student escape behavior suggests that it might be useful for building administrators to reevaluate test preparation activities and procedures being used in their building and to include anxiety reducing strategies. As a relationship was found, it sets the foundation for future studies to identify whether testing related activities are impacting some students emotionally and are causing unintended consequences of testing mandates.

Large-scale screening of a targeted Enterococcus faecalis mutant library identifies envelope fitness factors

Spread of antibiotic resistance among bacteria responsible for nosocomial and community-acquired infections urges for novel therapeutic or prophylactic targets and for innovative pathogen-specific antibacterial compounds. Major challenges are posed by opportunistic pathogens belonging to the low GC% gram-positive bacteria. Among those, Enterococcus faecalis is a leading cause of hospital-acquired infections associated with life-threatening issues and increased hospital costs. To better understand the molecular properties of enterococci that may be required for virulence, and that may explain the emergence of these bacteria in nosocomial infections, we performed the first large-scale functional analysis of E. faecalis V583, the first vancomycin-resistant isolate from a human bloodstream infection. E. faecalis V583 is within the high-risk clonal complex 2 group, which comprises mostly isolates derived from hospital infections worldwide. We conducted broad-range screenings of candidate genes likely involved in host adaptation (e.g., colonization and/or virulence). For this purpose, a library was constructed of targeted insertion mutations in 177 genes encoding putative surface or stress-response factors. Individual mutants were subsequently tested for their i) resistance to oxidative stress, ii) antibiotic resistance, iii) resistance to opsonophagocytosis, iv) adherence to the human colon carcinoma Caco-2 epithelial cells and v) virulence in a surrogate insect model. Our results identified a number of factors that are involved in the interaction between enterococci and their host environments. Their predicted functions highlight the importance of cell envelope glycopolymers in E. faecalis host adaptation. This study provides a valuable genetic database for understanding the steps leading E. faecalis to opportunistic virulence.

Modelling and simulations of ductile iron solidification-induced variations in mechanical behaviour on component and microstructural level

The mechanical behaviour and performance of a ductile iron component is highly dependent on the local variations in solidification conditions during the casting process. Here we show a framework which combine a previously developed closed chain of simulations for cast components with a micro-scale Finite Element Method (FEM) simulation of the behaviour and performance of the microstructure. A casting process simulation, including modelling of solidification and mechanical material characterization, provides the basis for a macro-scale FEM analysis of the component. A critical region is identified to which the micro-scale FEM simulation of a representative microstructure, generated using X-ray tomography, is applied. The mechanical behaviour of the different microstructural phases are determined using a surrogate model based optimisation routine and experimental data. It is discussed that the approach enables a link between solidification- and microstructure-models and simulations of as well component as microstructural behaviour, and can contribute with new understanding regarding the behaviour and performance of different microstructural phases and morphologies in industrial ductile iron components in service.

Aerobic power and lean mass are indicators of competitive sprint performance among elite female cross-country skiers

The purpose of this study was to establish the optimal allometric models to predict International Ski Federation’s ski-ranking points for sprint competitions (FISsprint) among elite female cross-country skiers based on maximal oxygen uptake (V̇O2max) and lean mass (LM). Ten elite female cross-country skiers (age: 24.5±2.8 years [mean ± SD]) completed a treadmill roller-skiing test to determine V̇O2max (ie, aerobic power) using the diagonal stride technique, whereas LM (ie, a surrogate indicator of anaerobic capacity) was determined by dual-emission X-ray anthropometry. The subjects’ FISsprint were used as competitive performance measures. Power function modeling was used to predict the skiers’ FISsprint based on V̇O2max, LM, and body mass. The subjects’ test and performance data were as follows: V̇O2max, 4.0±0.3 L min-1; LM, 48.9±4.4 kg; body mass, 64.0±5.2 kg; and FISsprint, 116.4±59.6 points. The following power function models were established for the prediction of FISsprint: 3.91×105 ∙ VO -6.002maxand 6.95×1010 ∙ LM-5.25; these models explained 66% (P=0.0043) and 52% (P=0.019), respectively, of the variance in the FISsprint. Body mass failed to contribute to both models; hence, the models are based on V̇O2max and LM expressed absolutely. The results demonstrate that the physiological variables that reflect aerobic power and anaerobic capacity are important indicators of competitive sprint performance among elite female skiers. To accurately indicate performance capability among elite female skiers, the presented power function models should be used. Skiers whose V̇O2max differs by 1% will differ in their FISsprint by 5.8%, whereas the corresponding 1% difference in LM is related to an FISsprint difference of 5.1%, where both differences are in favor of the skier with higher V̇O2max or LM. It is recommended that coaches use the absolute expression of these variables to monitor skiers’ performance-related training adaptations linked to changes in aerobic power and anaerobic capacity.

Wayne McGregor's choreographic language agent

The paper notebook with its companion pencil or pen is a creative tool for many contemporary choreographers and their dancers. Using the notebook affords a relationship with a set of external objects inscribed “on the page” in the form of drawn sketches, notations, and diagrams combined with text (Blackwell et al.). This relationship can be described in cognitive terms, for example, where the page becomes a surrogate for working memory, or a way for seeing something new by modeling structures or processes. The notebook in this sense becomes a site for the encounter of cognition and creativity, providing a place for thinking generatively with external objects (sketches, notations, etc.), an idea this essay will revisit.

Shopping for schools or shopping for peers : public schools and catchment area segregation

Market theory positions the consumer as a rational choice actor, making informed schooling choices on the basis of ‘hard’ evidence of relative school effectiveness. Yet there are concerns that parents simply choose schools based on socio-demographic characteristics, thus leading to greater social segregation and undercutting the potential of choice to drive quality improvements. In this paper we explore segregation by examining catchment areas for a range of public high schools in a specific middle-class urban area. We focus on socio-demographic characteristics, including levels of income, country of birth and religion affiliation, in order to explore residential segregation according to public high school catchment areas. Our data suggests distinct residential segregation between catchment areas for each public school within our dataset, particularly for the schools deemed to be popular and rejected, that may pose risks for broader equity concerns. We argue that, in contrast to market theory, even more affluent and active choosers are not equipped with information on the programmatic quality of their different school options, but instead may be relying on socio-demographic characteristics of schools—through surrogate information about the urban spaces that the schools occupy—in order to choose peer groups, if not programs, for their children.

Investigating relative respiratory effort signals during mixed sleep apnea using photoplethysmogram

Sleep disordered breathing does show different types of events. These are obstructive apnea events, central apnea events and mixed sleep apnea (MSA) which have a central component with a pause in airflow without respiratory effort followed by an obstructive component with respiratory effort. The esophageal pressure (Pes) is the accurate method to assess respiratory effort. The aim of the present study is to investigate whether the features extracted from photo-plethysmogram (PPG) could relate with the changes in Pes during MSA. Therefore, Pes and PPG signals during 65 pre-scored MSA events and 10 s preceding the events were collected from 8 patients. Pulse intervals (PPI), Pulse wave amplitudes (PWA) and wavelet decomposition (Wv) of PPG signals at level 8 (0.15-0.32 Hz) were derived from PPG signals. Results show that significant correlations (r = 0.63, p < 0.01; r = 0.42, p < 0.05; r = 0.8, p < 0.01 for OSA part) were found between reductions in Pes and that in PPG based surrogate respiratory signals PPI, PWA and Wv. Results suggest that PPG based relative respiratory effort signal can be considered as an alternative to Pes as a means of measuring changes in inspiratory effort when scoring OSA and CSA parts of MSA events.

Registro de pacientes con distrofinopatías en Colombia

INTRODUCCIÓN. La distrofia muscular de Duchenne es una enfermedad neuromuscular con una herencia recesiva ligada al X que afecta a 1 de cada 3500 niños nacidos vivos. Se produce por mutaciones en el gen DMD que codifica para la distrofina. Se caracteriza por manifestaciones clínicas variables típicas de una distrofia muscular proximal progresiva. OBJETIVO. Realizar el primer registro en Colombia de los pacientes identificados con distrofinopatías, teniendo en cuenta características clínicas y paraclínicas, así como las mutaciones causales de esta patología. METODOLOGÍA Es un estudio descriptivo, transversal, de la revisión de historias clínicas de los pacientes con diagnóstico de DMD atendidos en la consulta de Genética de la Universidad del Rosario durante los años 2006 a 2015. RESULTADOS Se identificaron 99 pacientes, de los cuales 56 (56,56%) corresponden al fenotipo Duchenne y 12 (12,12%) al Becker. No fue posible clasificar a 31 pacientes (31,3%) por falta de datos clínicos. La edad de inicio de los síntomas fue en promedio de 4,41 años. Las mutaciones más frecuentes fueron las deleciones (69%), seguidas por las mutaciones puntuales(14%), las duplicaciones (11%) y por otras mutaciones (4%). CONCLUSIONES Este registro de distrofinopatías es el primero reportado en Colombia y el punto de partida para conocer la incidencia de la enfermedad, caracterización clínica y molecular de los pacientes, garantizando así el acceso oportuno a los nuevos tratamientos de medicina de precisión que permitan mejorar la calidad de vida de los pacientes y sus familias.

Wild carrot differentiation in Europe and positive selection at DcAOX1 gene

By definition, the domestication process leads to an overall reduction of crop genetic diversity. This lead to the current search of genomic regions in wild crop relatives (CWR), an important task for modern carrot breeding. Nowadays massive sequencing possibilities can allow for discovery of novel genetic resources in wild populations, but this quest could be aided by the use of a surrogate gene (to first identify and prioritize novel wild populations for increased sequencing effort). Alternative oxidase (AOX) gene family seems to be linked to all kinds of abiotic and biotic stress reactions in various organisms and thus have the potential to be used in the identification of CWR hotspots of environment-adapted diversity. High variability of DcAOX1 was found in populations of wild carrot sampled across a West-European environmental gradient. Even though no direct relation was found with the analyzed climatic conditions or with physical distance, population differentiation exists and results mainly from the polymorphisms associated with DcAOX1 exon 1 and intron 1. The relatively high number of amino acid changes and the identification of several unusually variable positions (through a likelihood ratio test), suggests that DcAOX1 gene might be under positive selection. However, if positive selection is considered, it only acts on some specific populations (i.e. is in the form of adaptive differences in different population locations) given the observed high genetic diversity. We were able to identify two populations with higher levels of differentiation which are promising as hot spots of specific functional diversity.